Search Documents

By Dietmar Eifler, Benjamin Jost, Marcus Klein

This paper focuses on the ductile cast iron EN-GJS-600 which is often used for components of combustion engines. Under service conditions, those components are mechanically loaded at different temperatures. Therefore, this investigation targets at the fatigue behavior of EN-GJS-600 at ambient and elevated temperatures. Light and scanning electron microscopic investigations were done to characterize the sphericity of the graphite as well as the ferrite, pearlite and graphite fraction. At elevated temperatures, the consideration of dynamic strain ageing effects is of major importance. In total strain increase, temperature increase and constant total strain amplitude tests, the plastic strain amplitude, the stress amplitude, the change in temperature and the change in electrical resistance were measured. The measured values depend on plastic deformation processes in the bulk of the specimens and at the interfaces between matrix and graphite. The fatigue behavior of EN-GJS-600 is dominated by cyclic hardening processes. The physically based fatigue life calculation “PHYBALSIT” (SIT = strain increase test) was developed for total strain controlled fatigue tests. Only one temperature increase test is necessary to determine the temperature interval of pronounced dynamic strain ageing effects

Jan 1, 2015

By G. A. Brooks

Increasing interfacial area through gas injection is one of the main methods for accelerating reaction between slag, metals, and gases in modern pyrometallurgical reactors. In slag-metal reactors, the generation of a large number of metal droplets into the slag phase through high gas velocity has a much larger effect on the overall kinetics compared to the enhanced mass transfer through mixing. Top blowing technology generates large interfacial areas (>300 m2/tonne) through high impingement gas velocity at short distances between the exit of the injection lance and the metal-slag interface. Phase separation may become a limit at the case of very high interfacial areas, though there is still only limited understanding of the trajectories of metal droplets in slag-metal-gas emulsions.

Jan 1, 2003

By Michel G. Drouet

Dross, a major by-product of all processes involving molten aluminum, forms at the surface of the molten metal as the latter reacts with the furnace atmosphere. It generally represents 1 to 5 wt% of the melt, depending on the process, and contains on average about 50% free aluminum dispersed in an oxide layer. Since aluminum production is highly energy-intensive, dross recycling is very attractive from both the energy and the economic standpoints. The conventional recycling process using salt rotary furnaces is thermally inefficient and environmentally non-acceptable because of the production of salt slags. Hydro-Quebec has developed and patented a new salt-free technology using a rotary furnace heated by an electric arc between two graphite electrodes, called DROSCAR®. A 600-kW pilot plant in operation at LTEE is in use to demonstrate the process. This process provides aluminum recovery rates over 90%, using a highly energy efficient, environmentally sound production method. In 1994, 400 tonnes of aluminum dross were treated in this facility and several tests on various types of dross have also been conducted in early 1995. A report on the results will be presented.

Jan 1, 1995

By Akira Yazawa, Kazuo Koike, Mitsuhisa Hino

"The vapor pressures of MS (PbS, SnS and Sb2S3) in the molten Cu2S-MS, FeS-MS pseudo-binary and Cu2S-FeS-MS ternary systems were measured by means of a transportation method in the temperature range of 1323 and 1423K to calculate MS activities in the sulfide melts. The activities of MS in these systems show negative deviation from ideal behavior except the FeS binary systems which exhibit nearly ideal behavior in the homogeneous melts. The activities of the Cu2S-FeS pseudobinary system, which is fundamentals of the copper matte, were estimated from the activity values in the ternary systems and exhibit negative deviation from ideality.The distribution behavior of tin between the ·matte and silica saturated fayalite slag was investigated under the controlled partial pressures of S02 at l 523K. It was found that, in general, tin is distributed in the both phase, while tin is concentrated to the slag phase with increasing copper content in the matte. The activity coefficient of SnO in the slag was calculated based on the distribution ratio combined with the activity coefficient in the Cu2S-FeS system.IntroductionThe thermodynamic properties related to the Cu2S-FeS system and the Cu2S-FeS-MS systems (where MS can be PbS, SnS, Sb2S3, As2S3, Bi2S3, etc.) is required to be better understanding of the copper smelting process. However, thermodynamic analysis such as the distribution of impurities among the gas, slag and matte phases is difficult due to lack of thermodynamic data. In this study, the vapor pressures of MS (PbS, SnS and Sb2S3) in the Cu2S-MS, FeS-MS. and Cu2S-FeS-MS systems were measured by a transportation method. The distribution behavior of tin between the matte and silica saturated fayalite slag was also investigated. The results in the present experiments are useful to analyze thermodynamically the behavior of component in the copper matte smelting."

Jan 1, 2000

By C. A. Pickles

At the present time, pyrometallurgical processes are employed for the recovery of lead from battery scrap. These processes have serious pollution problems, primarily due to the emfssion of sulphur dioxide and airborne lead in the form of dust and fume. In addition it is necessary to dispose of solid wastes and liquid effluents which contain lead and in some cases sodium sulfide-containing compounds. In this work an improved process was investigated for the recovery of lead from battery residue. This involved pelletization of the residue with sodium carbonate and moisture. Then, the pellets were melted without carbon and the .sodium sulphate salt was removed. Subsequently, the molten lead oxide was reduced with carbon. This process minimizes the sulphur dioxide emissions and leads to very low sulfide contents of the sodium sulfate salt

Jan 1, 1992

By G. H. Khoe

Although some hydrometallurgical process liquors contain significant amounts of ferrous and arsenate ions, no reliable thermochemical data for the aqueous complexes and the solubility of the ferrous arsenate precipitate are available. The complexation of iron(11) with arsenate has been investigated using the potentiomemc titration method. The results indicated that virtually no complexation of iron(@ with arsenate has been observed. This is in contrast to the significant complexing reported for iron(1n) with arsenate. The solubility product of the precipitate was calculated using the concentrations of appropriate arsenate species pertaining to the observed precipitation pH's. The fit of the observed precipitation points on the solubility curve of the computed stability diagram was used to assess the appropriateness of the equilibrium model.

Jan 1, 1991

A comprehensive numerical capability for the analysis of Thermal Spray (TS) systems consisting of a three-dimensional compressible, turbulent flow Navier-Stokes model and a multi-phase particle flow model in Lagrangian formulation, was developed. This capability is validated for a set of flow conditions typical for TS. The developed methodology is used for analysis of the JP-5000 TS gun gas and coating powder flow conditions. Modeling and analysis of particle/turbulent eddies interaction is performed. Details of gas flow field, particle temperature, and particle velocity histories, and particle temperature, velocity profiles in the system are presented. For the validation of numerical analysis, the computed results are compared with available experimental measurements. The flow phenomena for different flow parameters are analyzed and explained as the results of gas dynamics and heat and momentum transfer between the gas and particle phases. This methodology can be used for process control and reliability improvement, and has the potential to significantly improve TS gun performance through control of its parameters.

Jan 1, 1996

By Wenbo Luo, Kang Liu, Fusheng Mao, Jilai Xue, Jun Zhu, Chunlei Yang

Extracting alumina from coal fly ash (CFA) is of great interest for both environmental protection and recycling valuable alumina content. In this study, ultrasonic aided leaching process as an effective method was investigated to enhance extracting Al2O3 from CFA via concentrated sulfuric acid sintering. The influence of ultrasonic power and processing time were tested under the conditions as the same as those without ultrasound. It is found that the alumina extraction rate can reach 90.5 % with ultrasound assistance, while the ultrasonic treatment can reduce almost 15 ~ 30 min in leaching time and 5 ~ 10 oC in leaching temperature than those without ultrasonic operation at the same Al2O3 extraction rate. In addition, the ultrasonic can reduce calcium content by 6 ~ 8 % dissolved into the leaching liquid. SEM analysis also shows that the residue particle size with ultrasound is smaller than that without ultrasonic treatment.

Jan 1, 2015

By D. Silva-Galvan, R. D. Morales, S. Gonzáelez-López, A. Romero-Serrano, G. Plascencia-Barrera, F. Chavez-Alcala

This work is focussed on lead decopperising by two techniques: conventional top addition of sulfur and injection of sulfur powder. It is found that the first method proceeds under equilibrium conditions and the second one depends on kinetic considerations. Experiments were carried out using 15 kg lead baths at two temperatures, 340°C and 380°C. The carrying gas used for the injection trials was nitrogen at flow rates of 6.3 and 18.6 L min- 1• The results show that 'decopperising process is more efficient at temperatures close to the melting point of lead for the sulfur top addition process, whereas high temperatures produce better copper removal for the injection of sulfur powder. Besides, the sulfur injection with the higher nitrogen flow rate (18.6 L min-1) produced higher decopperising rates. Thermodynamic and kinetic models are used to simulate this lead refining process.

Jan 1, 2000

By Huanmei Yuan, Yuanyuan Wang, Hao Bai

Composite phase change materials are widely used in energy-saving and energy efficient process. Nano-encapsulated phase change materials are especially significant for making advanced working fluid applicable to waste heat recovery or storage. In this study, silica-coated stearic acid (SA) Nano composite phase change materials were prepared from tetraethyl orthosilicate (TEOS) and stearic acid (SA) via sol-gel process. The materials were investigated by Field emission scanning electron microscopy (FE-SEM), Transmission electron microscope (TEM), Fourier transform infrared spectroscopy(FT-IR) and Differential scanning calorimeter (DSC).The FE-SEM and TEM results show that monodisperse microspheres with stable core– shell structure were formed and SA was encapsulated in the silicon dioxide shell. The FT-IR results show that there were no chemical reaction between silicon dioxide and SA, which is the chemical property of the composite material, is stable. The DSC results show that the composite phase change material has favorable heat capacity.

Jan 1, 2016

By Bart Blanpain, Tom Peter Jones, Muxing Guo, Liugang Chen, Huayue Shi

Fayalite based slag is formed during the smelting process of secondary copper resources. It was found that with the presence of high ZnO, the slag became viscous, causing a slag tapping problem. In the present paper, the phase relations of the slag system ZnO-“FeO”-SiO2-Al2O3- CaO (ZnO = 0-12 wt%, Al2O3% = 0-15 wt%, CaO = 0-1.5 wt%, with iron saturation) at 1150 °C is studied by using quenching technique followed by phase identification and compositional analysis of equilibrated samples. The dependence of FeO and Al2O3 solubility in the liquid slag on the chemical composition of slag is characterized. Based on the experimental data, the solid fraction of the slag, which may considerably, influences the slag viscosity, at the tapping temperature can be reasonably estimated and, therefore an appropriate modification of the slag composition can be made.

Jan 1, 2016

By K. C. Mills, P. N. Quested, A. P. Day, R. F. Brooks

"Methods have been developed to measure the physical properties of molten materials relevant to the fluid flow in high temperature processes. Data for the densities, viscosities and surface tensions of Al-, Ni- and Fe-based alloys are compared with (i) values for the pure metals and (ii) estimated values obtained from models making use of chemical composition of the alloy. Experimental values for metallurgical slags are also given and compared with estimated values.1 IntroductionPhysical property data has proved very useful in improving process control and product quality. For instance, in the continuous casting of steel the viscosity (TJ) of the mould flux is important since it determines (i) the optimum casting conditions, nVc = 2.5±1 dPas (m min-1) where V c is the casting speed and (ii) the level of slag entrapment (which leads to inclusions) in the metal. Thus data for properties like viscosity are exceedingly useful in understanding the process and the problems encountered and the causes of defects and problems.Another interesting development which has helped to increase our knowledge of processes and improve process control and product quality is the development of mathematical models of the fluid and heat flow in the process. These models have been developed to the stage where one of the prime requirements is for good physical property data for the industrial materials involved. Recently, Oxley [1] has shown that the use of reliable, experimental, property values for the commercial alloy in a commercial software package produced a significant improvement in the prediction of casting defects. Thus reliable property data are required for liquid metals but also for (i) liquid slags since many processes involve the use of a slag to refine and protect the metal or to lubricate the mould and (ii) refractories, sand and investment moulds."

Jan 1, 1999

By Yusuke Kimura, Ken-ichi Yamaguchi

"Secondary materials have long been processed at the S-furnace of the Mitsubishi continuous copper smelting and converting process at Naoshima Smelter and Refinery. Intensive recycling in the recent years has formed concerns that impurities in the secondary materials may cause drastic changes in the chemical properties of the CL-slag, which is separated from matte in the smelting stage. Among various impurities included in secondary materials, the authors have studied the influences of sodium oxides in the CL-slag because the behavior of sodium oxide has scarcely been studied with respect to the copper smelting slag. The examinations have been applied experimentally on the distribution between slag and matte of arsenic whose acidic characteristics suggest strong affinity to sodium-oxide of basic characteristics in silicate melts. The results have been discussed by thermodynamic evaluations and the results of pyro-tests at the commercial furnace.IntroductionAt Naoshima Smelter and Refinery, the existing line of the Mitsubishi continuous copper smelting and converting process has been operated since 1991. The Mitsubishi Process consists of three furnaces namely the S-, CL- and C-furnace as shown in Figure 1. In the S-furnace, copper concentrate and powdery secondary materials (scraps, sludges, etc) are charged through the top lances with oxygen enriched air. The other secondary materials of lumpy shapes are charged through the chute installed on the furnace roof. Charged materials are smelted by the reaction heat in accordance with the oxidization of copper concentrate. The mixed melt of matte and slag overflows through the launder into the CL-furnace, where the melt is separated into slag and matte by the difference of their specific gravity. Matte is siphoned out and sent to the C-furnace and converted to blister copper continuously. The CL-slag overflows continuously through the slag outlet to be water-granulated. Granulated slag is sold as a raw material used for the cement production and so on. Various secondary materials have been processed at the S-furnace of Naoshima Smelter and Refinery. Intensive recycling in the recent years has formed concerns that the chemical properties of the CL-slag may change drastically due to impurities originating from secondary materials. Among various impurities included in secondary materials, the authors have studied the influence of sodium oxide in the CL-slag because the impact of sodium oxide has scarcely been studied with respect to the copper smelting slag. The examinations have been applied experimentally on the distribution between slag and matte of arsenic whose acidic characteristics suggest strong affinity to sodium-oxide of basic characteristics in silicate melts."

Jan 1, 2012

By J. N. Hryn

This paper describes some of the work done in Phase 1 of a multi-year, five-phase program aimed at demonstrating the economic feasibility of producing commercial-scale quantities of commodity materials derived from salt cake residue-oxide. The amount of salt cake generated annually in the U. S. is estimated to be 510,000 tons, including 340,000 tons of residue-oxide. Used beverage can (UBC) processing accounts for the majority of residue-oxiae that could be made available for further processing into commercial products. To characterize the composition of residue-oxide. eight residue-oxide samples from various secondary processors were obtained and analyzed. Surprisingly, the composition of residue-oxide was found to be independent of source or alloy family being processed, with? the exception of slightly elevated silicon levels in 3XXand UBC residue-oxide samples. Major phases detected in the residue- oxide were? alumina, spinel, and aluminum hydroxides. Preliminary economic analyses indicated that the refractory market appears to be the best choice for high value-added products produced from residue-oxide with minimum processing. Bench-scale tests indicated that low silicon containing residue-oxide is ready to enter this market, but the elevated silicon content of UBC and 3XX residue-oxide preclude this possibility. A separation technology should 'be developed to remove silicon-containing . species from the alumina and spinel values Present in residue-oxide. This technology would then allow UBC and 3XX residue-oxides to be converted to significantly higher value-added products.

Jan 1, 1995

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

"The effects of five commercially available foaming reagents (range of 0 to 25 ppm) namely Dowfroth 250, Saponin, Yucca, Licorice and Meta-Para Cresol on acid mist control, current efficiency, polarization behavior, and deposit morphology and orientation were investigated. The deposition was carried out using a bench scale electrolysis apparatus (cell volume 3L) at 500 Nm-2 and 38°C for 3 hours from Kidd Creek zinc electrolyte. The acid mist control capability of the various reagents was studied and compared by characterizing the foam layer generated during actual electrowinning conditions and by direct quantitative measurements of acid mist levels on top of the electrowinning cells. Within the range considered, the addition of these reagents reduced the current efficiency, refined the grain size of the deposit, and changed to preferred orientation of most of the deposits. Among the reagents tested, acid mist measurements indicated that Licorice and Dowfroth 250 were the best acid mist suppressant at emissions of 0.30 mglm3 and 031 mg/m3 respectively while Yucca and MPC produced the most mist at 3.0 mg/m3 and 33 mg/m3 emission rates, respectively.IntroductionMost of the world's primary zinc is produced via a combined roast-Ieach-purificationelectrowinning process. Depending on the electrolysis conditions, several additives may be added to the electrolyte. Some (e.g. glue, antimony, sodium carbonate) are added to mainly counteract the detrimental effects caused by impurities while others (e.g. licorice, Saponin) are used as foaming reagents to prevent excessive acid mist formation. Acid mist emission is a problem in many electrolysis operations because it corrodes the equipment and is a health hazard to the workers in the tankhouse as well as it pollutes the environment. Due to recent trends towards more environmental protection and more stringent in-plant hygiene, there is an increasing need to minimize these aerosols. In order to eliminate or minimize these aerosols foaming agents are usually added to the electrolyte to produce a foam layer on top of the electrolyte, thus trapping most of the mist. The ideal foaming agent would trap all of the mist and would not interfere with the electrowinning process. It is also evident that the reagent toxicology, cost and availability are important factors that need to be considered.Review of the available literature clearly indicated that very little work has been done in the past on the subject of acid mist control in electrowinning operations particularly in the area of foaming and anti-misting properties of surfactants. Two papers [1,2] have reviewed briefly the existing technologies for acid mist control. Recently, most of the work in this area has focused on the development of special mechanical devices that could be attached to the electrodes and control the mist generation at the source before it is emitted to the cellhouse [2-5]. On the other hand, extensive body of literature exists that deals with the effects of anti-misting reagents on the electrowinning aspects [6-7]."

Jan 1, 1997

By Laihua Wang, Peter Hayes, Hae-Geon Lee

"This paper introduces a new process for the efficient removal of dissolved gases and inclusions from liquid metals. This process involves the creation and dispersion of fine bubbles in molten metals by introducing inert or reactive gas into a region of turbulent flow. The highly turbulent metal flow splits the gas into fine bubbles and results in good mixing between the gas and molten metal phases. These conditions are ideal for contacting inclusions in the metal with the bubbles and subsequent flotation of the inclusions to the metal-slag interface where the inclusions are then absorbed by the covering slag layer. Dissolved gases, such as [H], [0], [N] in the metals are also transferred to the gas bubbles and removed from solution.The process concept has been previously demonstrated using a full-scale air/water model to simulate the ladle-to-tundish system of continuous casting of steel. The present cold modelling work has further demonstrated the ability of the process to remove gas solutes. The results indicate that the efficiency of new process is several hundred times greater than that of conventional high speed rotating injectors which are currently applied in the treatment of liquid light metals.IntroductionDuring metal smelting, refining and alloying processes, unwanted gas and second phase liquid or solid impurities are incorporated into liquid metals. In the case of steelmaking, the gas-forming impurities include [0], [H] and [N], and the solid impurities as a result of deoxidation include Ah03, Si02 inclusions. Common impurities in liquid aluminium are dissolved hydrogen and solid Ah03. To avoid subsequent problems during processing and to improve the physical properties of the metal products it is necessary to significantly reduce the level of impurities."

Jan 1, 1996

By David G. C. Robertson

A new approach is described for the calculation of the kinetics of metal/slag, metal/slag/gas, and metal/matte/slag/gas reactions. The algorithm assumes that equilibrium is achieved at the interface between phases, and uses an equilibrium solver (such as SOLGASMIX) to compute the equilibrium state at the interface at each time step during the reaction. For multiple phase systems a number of unit operations, representing the different phases and interfaces, must be connected together in a reasonalbly complex manner, and the METSIM software package has been utilized for this purpose. The new approach is superior to the SMAK software developed by the author and his co-workers over the past decade, for the reasons discussed in this paper.

Jan 1, 1995

By Patrick M. Eduafo, Brajendra Mishra, Mark L. Strauss

Direct acid leaching of rare earth metals (REMs) from waste lamp phosphors is non-selective, leading to co-dissolution of impurities mainly calcium, phosphorus, silicon, iron and zinc. Calcining the phosphor powder at different temperatures followed by leaching with HCl isn’t efficient for the extraction of all the chief rare earths especially cerium (Ce), lanthanum (La) and terbium (Tb). Therefore, multi-stage leaching operations are required for the separation of the REMs in phosphor dust. This paper will outline a new process for extracting Ce, La, Tb, Eu and Y from waste fluorescent lamps using a three-stage leaching and separation process. A flowsheet has been developed which shows this process is selective and efficient.

Jan 1, 2015

By Marcelo A. Martorano, Moyses L. Lima, João B. F. Neto

"Directional solidification is an essential refining step to obtain solar grade silicon from metallurgical silicon. This step can be carried out in a Bridgman furnace, where nearly constant temperature gradients and solidification velocities are imposed on the solid-liquid interface. In the present work, this directional solidification was conducted in a static furnace, in which large temperature gradients and low solidification velocities were enforced to increase macrosegregation. The resulting ingots were analyzed regarding their macrostructures, microstructures and chemical composition. Using measured cooling curves in the ingot as boundary conditions, a mathematical model based on the concept of a stagnant liquid layer at the solid-liquid interface was implemented to predict the macrosegregation profiles. The chemical analyses of the ingots show macrosegregation of several impurities to the ingots top. The mathematical model indicates that liquid convection plays an important role in stabilizing the planar solid-liquid interface, increasing the macrosegregation of impurities.IntroductionMost of silicon used for photovoltaic (PV) energy production is obtained by chemical processes, such as, Siemens and its derivations [1]. However, these chemical processes have drawbacks related to relatively high energy consumption and investment costs, and to safety and environmental problems. In order to overcome these difficulties and to fulfill the silicon demand for PV applications, several metallurgical routes are under development [2] to produce silicon of enough purity to PV applications (SoG-Si) from metallurgical grade silicon (MG-Si).Metallurgical routes involve different steps among which the directional solidification is pointed out as a fundamental one [1]. Directional solidification can cause macrosegregation of impurities to the last part of the ingot to solidify. The impurity segregation during solidification is related to the low solute partition coefficient (k0) between liquid and solid silicon. Most of the impurities in MG-Si have k0 << 1, except for boron, phosphorus and oxygen, which require specific steps of the metallurgical routes to be eliminated. The equilibrium partition coefficient and the solubility limits for the most important impurities in MG-Si are shown in table 1"

Jan 1, 2014

By Ana E. Bohé

Chlorination process is an attractive and efficient method for the metal recovery from complex materials. The process that is performed at high temperatures, allows converting all the metals contained in the material into their respective chlorides which are further separated in a selective way. Aluminum metal matrix composites with discontinuous ceramic reinforcement of short fibers, whiskers, and particles have been gaining wide acceptance as an important engineering material in automotive, aerospace, and electronic industries. Since the ceramic reinforcements are still quite expensive and contribute significantly to the final cost of composite materials, the feasibility of their recovery from the manufacturing scrap and further recycling is a factor of increasing economic interest. In the present work, a theoretical and experimental study is given for the recovery of Al2O3 and SiC particles and short fibers from three commercially available aluminum-matrix composites produced by molten metal mixing route. The process consists of transforming the constituents of metallic alloy matrices in gaseous chlorides that are dragged by the gaseous stream, while the ceramic reinforcement remains as a solid residue in the reaction bed.

Jan 1, 2006