Search Documents

By María Cristina Ruiz

Hematite precipitation is a convenient alternative for the removal of iron from leaching circuits because of its chemical stability, high density and high iron content. The precipitation of hematite from ferrous sulfate solutions was studied in a batch reactor. The precipitation occurs by two sequential steps: oxidation of the ferrous to ferric ions followed by hydrolysis of the ferric to hematite. The main objective of this study was to determine the effect of the main operating variables on the rate of two steps of hematite precipitation. The variables studied included: stirring speed (100 to 600 rpm), temperature (160 to 200 ºC), concentration of sulfuric acid (1 to 10 g/L), initial iron concentration (1 to 15 g/L), and partial pressure of oxygen (1 to 6 atm). The sulfur content and the particle size of the solids that precipitated under various conditions were also determined. The results showed that at low temperature and high acid concentration the rate of Fe3+ hydrolysis is the step that controls the overall process. The variable that affects most the rate of Fe2+ to Fe3+ oxidation and the rate of hematite precipitation is the temperature.

Jan 1, 2008

By Tao Jiang

Germanium is widely used in many fields, and the production of germanium is very important. The effects of initial sulfuric acid concentration, liquid to solid ratio and other parameters on the leaching rate of germanium and zinc from germanium-bearing zinc oxide has been studied. The occurrence and form of germanium and other elements in the leach feed and the leach residue were studied by EPMA, XRD and chemical analyses. The experiments showed that the leaching rate of germanium and zinc was 91% and 88%, respectively under optimal conditions. Wurtzite was the main limiting factor for the leaching rate of zinc while the leaching rate of germanium was limited by insoluble germanium compounds. Furthermore, it was found that some germanium was bound up in galena in the leach residue. These results may be helpful for further improving the leaching rate of germanium in germanium-bearing zinc oxide.

By Dengfu Chen, Yunwei Huang, Mujun Long, Kui Lv, Pei Xu, Lin Bai

The surface temperature of continuous casting slab in the secondary cooling zone is a key parameter of production control. However, the accuracy of radiation temperature measurement of high temperature casting slab is greatly affected by the environmental factors, such as water vapor, spray, water film and other participational medias during continuous casting process. In this paper, the radiation characteristics of water vapor and its influences to radiation temperature measurement of continuous casting slab were investigated. Based on the database HITRAN 2004 and the measuring principle of monochrome thermometer & colorimetric thermometer, the measuring errors under different operating infrared spectral wavelength were compared. Results showed that spectral region with wavelength nearby 1.0μm or 1.6μm would be the optimum for high temperature infrared thermometer used under the conditions with moist steam, water spray and water film at the secondary cooling zone in steel continuous casting.

Jan 1, 2016

By Hideaki Tokuyama

Recovery of Ni from acidic wastewater of metal surface treatment has been investigated for reuse of the metal and water. Ion exchange equilibria between Ni ion and a strong acid cation resin, DIAION SKIB, and effective diffusivity in resin particle have been studied and they related to the concentration of HCI. The amount of adsorbed Ni for unit quantity of resin decreases with the increase in HCI concentration. This trend is remarkable for acid concentration above 0.1 kmol/m3,. The exchanging ratio of Ni2+ to H+ in resin particle is I/2 and the values of equilibrium coefficient K and maximum exchange capacity Q are I.62 and 3.16 keq/m3 -dry resin, respectively. Effective diffusivity D. determined from the observed breakthrough curve increases with increasing concentration of DC!. A prototype of moving bed has been developed and applied for the recovery of Ni from model solutions of wastewater prepared by mixing HCl and NiCl2. This apparatus allows us to control the resin flow rate by changing the cross sectional area of hole I the Teflon plate installed at the bottom of resin bed. Characteristics of Ni recovery have been clarified under various liquid flow rates. In any case for Q1, Ni ion has been effectively recovered on SKIB resin and the removed fraction was more than 99.5 %. Higher loading ratio of ion is attained at larger liquid flow rate.

Jan 1, 2003

By M. K. Patel, K. A. Pericleous, M. Molaei

"The future trading of carbon credits and increased financial cost necessitates substantial cuts in incidental C02 emissions in the production of metals (iron, steel, aluminum, zinc, lead). Although greener methods of production are being developed, in the short term the use of point-source C02 extraction using existing technology remains attractive. Accelerated natural carbonation, in a fluidized bed is a feasible technological route investigated in this research. CFD modelling has been used to study the efficiency of C02 capture in a fluidized bed reactor containing a CaO solid sorbent. A Lagrangian/Eulerian scheme describes describe CaO particle trajectories and exchange of mass, momentum and energy with the carrier gas, with a typical off-gas composition. Different reactor geometries are considered (with uniform, stepped and gradually expanding cross-section), to maximize conversion for a given particle loading and size distribution (100-200 microns). Removal efficiencies of up to 80% are demonstrated, making this a viable process.IntroductionBased on Intergovernmental Panel on Climate Change (IPCC) reports, the major cause of climate change and global warming is due to a high level of C02 concentration in the atmosphere resulting from fossil fuel combustion, particularly in coal-fired power plants [1]. Carbon capture and storage is therefore the most important action proposed to reduce C02 from combustion flue gases. In this process, carbon dioxide is captured and may then be regenerated as pure C02 and conducted to a permanent storage, or simply stored as a solid carbonate [2]. Capture and storage of C02 has an economic penalty and the main cost of this penalty is associated with the capture plant. Capturing C02 with a lime-based solid sorbent (CaO) is a very promising technique, due to the low cost and the wide availability of the reactant. In this process, the CaO reacts with C02 based on the following reaction in a reactor called a Carbonator:"

Jan 1, 2012

By P. Wieser, D. Feke

"Priming of filters with small pores is influenced by the surface tension of the liquid metal and may be complicated by freezing • Freezing followed by melting has been observed experimentally. This process has been modeled on the basis of one dimensional heat flow by radiation to the filter and by conduction in the metal. Also considered are super-heat of the metal and the initial filter temperature. The results of the model provide useful guidelines for the application of filters. IntroductionFiltration has been recognized as a valuable method of refining by removing suspended phases from liquid metals or alloys. Woven fiberglass type fabrics and wire screens were used initially in the aluminum industry. With the introduction of the ceramic filters that exhibit improved inertness and refractoryness, filtration has been introduced to higher melting alloys including cast irons, superalloys, stainless steels, as well as low and medium carbon low alloy steels. A considerable literature is delveloping rapidly on the progress in applications and the advances in understanding the mechanisms and effectiveness of filtration processes (1-8).With the use of filtration for different alloy systems for the production of cast to shape parts a bewildering variety of gating system modifications has been developed (Figure 1) to accommodate the installation of filters in the mold. The modifications have two principal purposes: 1) the runner expansion is intended to compensate for the resistance to flow due to the filter and that of the captured inclusions, and 2) the metal reservoir upstream of the filter, provides a temporary by-pass which permits metal to flow across the filter and heat it until priming can be accomplished. priming of.filters by low and medium carbon steel is readily accomplished but, compared to such alloys as cast iron or 19 Cr-9Ni stainless steel, requires greater precautions to avoid failure to prime by excessive freezing on or inside the filter pores. This problem is further examined below:"

Jan 1, 1986

By John J. Jonas, Sang-Hyun Cho, Ki-Bong Kang

"The recrystallization behavior of Nb micro alloyed steels containing Cr, Mo, Ni and Ti. was studied using hot torsion testing with the aim of modeling the recrystallization processes and the mean flow stress taking into account the microstructural behavior during hot rolling. The kinetics of static and metadynamic recrystallization were characterized and appropriate expressions were formulated for the recrystallization kinetics. These are shown that the recrystallization kinetics depend on steel composition and the processing conditions. The stress-strain curves were determined in order to derive new equations for the peak stress, peak strain, mean flow stress and softening kinetics. The peak strain is influenced by the presence of alloying elements; their addition, which has a solute drag effect, retards the rate of grain boundary motion, shifting the peak to the right. The addition of Nb to the steel results in a significant increment in the activation energy for hot deformation, and Mo has smaller effect than Nb, but Cr has the opposite effect. It was also found that the deformation activation energy in these steels was not altered by the addition of Ni. The rate of metadynamic recrystallization increases with strain rate and temperature and is observed to be independent of strain, in contrast to the observations for static recrystallization.The mean flow stress (MFS) calculations, based on the Sims analysis, are then compared with the predictions of a model based on an improved Misaka mean flow stress equation in which solute effects, strain accumulation, as well as the kinetics of static and metadynamic recrystallization are accounted for. Good agreement between the measured mean flow stresses, which is obtained from the mill logs of POSCO Kwangyang #3 HSM (hot strip mill), and 'predicted ones is obtained over the whole range of rolling temperatures. The results demonstrate that dynamic recrystallization followed by metadynamic recrystallization, supported by the unexpected load drops, sometimes occurs for the rolling schedules studied in the present analysis."

Jan 1, 2001

By Kandipati Sreenivasarao

A promising method for removing heavy metal ions from dilute effluents is ion- or precipitate- flotation, in which a suitable collector is added to form hydrophobic metal-collector complexes or compounds that can be collected as foams. We have successfully removed Cu(II), Cd(II), and Pb(ll) from dilute solutions using sodium dodecylsulfate and ethanol as collector and frother respectively. However the process would not be economically viable unless the collector could be recycled, and the heavy metals recovered in a concentrated, preferably marketable, form from the foams. We investigated four different methods to decompose heavy metal-dodecylsulfate complexes, namely precipitation of hydroxides, precipitation of sulfides, chemical stripping, and electrolysis. We compare the performance of these methods. In each case the observed behavior is related to known thermodynamic data, and potential applications are discussed.

Jan 1, 1995

By Fumito Tanaka

In the Mitsubishi Continuous Copper Smelting & Converting Process, the heat for the dissolution of scraps is effectively supplied from the melts strongly stirred by top injection. Various kinds of shape of scraps not only powder but also lump, sheet, cube and so on can be treated without any emission of dust and fugitive gas, and no additional furnaces for scrap processing is necessary. Therefore, this process is much suitable for recycling. The authors have investigated the melting rate of ice sphere into a water bath equipped with top blowing lances as a basic study for the dissolution of scrap. Hydrodynamic experiments were carried out, and mathematical models were applied to the results. The results show that the melting rate of ice sphere strongly depends on the standing waves at the bath surface.

Jan 1, 2001

By Bo Björkman

Four different arsenic containing dusts from the Boliden plant, Boliden mineral AB, Sweden have been examined. A kinetic study of the As elimination was performed in a laboratory scale roasting furnace for roasting furnace ESP dust and smelting furnace ESP dust. Characterisation and thermodynamic calculations were carried out to determine the mineralogy, and the stability of compounds in the dusts studied. The characterisation methods used were chemical analysis, X-ray diffraction analysis and microprobe analysis. It was found in the experiments that a high degree of As elimination was obtained for roasting fumace ESP dust and a low degree for smelting fumace ESP dust. Derived kinetic models are given. A prediction of the As-elimation for settling furnace dust and converter ventilation dust is presented.

Jan 1, 1994

By H. H. Law

Large amounts of waste material in the form of flue dust are generated in the operation of copper smelter furnaces. As a result of increasingly stringent disposal, it has become important to develop methods for treating such metallurgical wastes to extract metals and convert them into salable products. A two-step closed-loop hydrometallurgical process, has been developed: (1) extraction with sulfuric acid removes about 90% of zinc and decreases the dust volume by 50%; (2) extraction with hydrochloric acid dissolves the lead and further decrease the dust volume by 75%. A process scheme for generating salable products is proposed.

Jan 1, 1992

By Kouji Mimura, Manabu Kishida, Minoru Isshiki

"Purification of metallurgical grade silicon (MG-Si) by the plasma-arc zone melting method (PZM) has been examined. The process consisted in the horizontal displacement of a molten zone heated by Ar- and 10%H2+Ar- plasma-arc under atmospheric pressure. This technique, especially using hydrogen plasma-arc, promoted the segregation of impurities from the head to the tail of the bar and the vaporization of impurities of higher vapor pressures. Metallic impurities such as Fe, Ti, Cr, Mn,. Cu, Al and Ca were reduced to less than 1 mass ppm at the head side of the Si bar. Non-metallic impurities such as boron, phosphorous, carbon and oxygen were also reduced by the zoning effect and, furthermore, by activated hydrogen atoms dissociated in the high temperature plasma-arc according to the following reaction: Q (in liq.Si) + 2H = H20. Plasma-arc zone melting with hydrogen plasma has been recognized to become an effective purification technique of MG-Si for the production of a low cost solar grade Si (SOG-Si).IntroductionDemand of high-purity Si for solar grade silicon (SOG-Si) is supposed to be further growing in the near future. The purity of SOG-Si required for the photovoltaic cell is more than six nines. An expensive semiconductor grade silicon (SEG-Si) with the purity of around eleven nines has been used to satisfy the demand. Development of techniques and processes for the production of a low cost SOG-Si is therefore necessary [l]. Although many purification techniques, such as directional solidification, plasmaarc melting and electron beam melting [1-6], and processes, such as carbothermic reduction of high purity silica [7], have been examined and proposed for this purpose, a more efficient and practical purification technique is still required.In the present work, the purification of MG-Si has been investigated using a plasma-arc zone melting (PZM) technique developed by the authors. Plasma-arc melting, which is well· known as a useful melting method for various metals and alloys, has been recognized to be efficient for refining and degassing several metals if hydrogen is added to the plasma generating gas, resulting in the so-called hydrogen plasma-arc. For example, deoxidation of Fe, Co and Ta [8,9], decarburization of Fe [9] and removal of metallic impurities from Zr, Ta and Fe [10-12] have been reported. This excellent refining effect is considered to be caused by dissociated and activated hydrogen atoms formed in the high temperature plasma-arc."

Jan 1, 2000

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

"In order to make the stainless steel making process efficient and environment friendly, it is essential to minimize the loss of chromium to the slag phase. With a view to investigate the advantages of using CO2 to attain moderate oxygen partial pressures in the oxidant gas during the decarburizations of stainless steel, the present experiments were carried out to understand the oxidation kinetics of Fe-Cr alloys and Fe-V alloy with gas mixtures containing CO2. In the present work, the oxidation behavior of Fe-Cr and Fe-V was examined by thermogravimetric analysis (TGA). Various mixtures of O2 and CO2 were used as the oxidant gas and the oxidation rate was followed by the weight changes as a function of time.The experiments demonstrated that the oxidation rate is independent of temperature at present experimental situation, but has strongly related to the Cr-content of the alloy as well as the oxygen partial pressure in the oxidant gas mixture. The wetting of alumina by the iron drop and the change of the drop shape during the course of the oxidation were investigated by X-ray radiography."

Jan 1, 2010

By F. Qian

Direct impingement of molten metal baths by a gas jet is commonly encountered in such processes as BOF and electric arc furnace steelmaking. Shape and local fluid mechanics in the impinging region is important because it determines the interaction of the metal pool with the surroundings. Goal of the present work is to characterize and understand the interfaces at the impinging region. Using a physical model consisting of water/corn oil and water/kerosene as surrogates for metal/slag, interface shapes for slag-gas, slag-metal and metal-gas are investigated. Influence of transport properties of the two liquids on the shape and flow fields are also experimentally determined under various impinging jet conditions, namely jet momentum and jet height. The viscosity of the slag layer (corn oil or kerosene) has the most significant effect on the interface shape and the induced flow fields. The interface shapes were measured both photographically and by using a surface- tracking resistance probe. The limiting condition at which the jet breaks through the corn oil or kerosene layer and reaches the water layer was determined experimentally

Jan 1, 1994

By L. M. . Chia

The successful treatment of waste materials to recover metals with acceptable purity is often hampered by the presence of undesirable impurities. The problem is further complicated by the need to insure that any residues or solutions generated are environmentally acceptable. Hydrometallurgical processes involving leaching- solvent extraction-electrowinning offer some attractive features which address many of these problems. However, in certain instances trace impurities that contaminate the organics are difficult to chemically strip and interfere with the overall process efficiency. A new processing scheme has been developed which appears to provide some attractive alternatives for impurity removal from organics. It has been shown that many ionic impurities can be electrochemically removed from the organic by spontaneous direct reduction using solid metals. A variety of metal ion impurities have been removed from selected common organic extractants such as D2EHPA and TBP using different metals as the reducing agents. The results and probable mechanisms involved in the reactions are discussed.

Jan 1, 1994

By Sergio Sanchez-Segado, Yuan Zhang, Animesh Jha, Ahmad Fahmi Ruzaidi

Niobium and tantalum are considered critical materials because the increasing demand in the energy sector which is reliant on limited abundance of these two metals in minerals. Traditionally, niobium and tantalum mineralsare digested using hydrofluoric acid at moderate temperatures, producing oxy-fluorides which are separated by solvent extraction, involving the use ofhazardous chemicals. The increasing environmental pressures are forcing the industry to search for alternative low carbon processing methods. In this paper alkali roasting based separation and beneficiation, which is not well understood in the literature, is proposed, for which the kinetics and thermodynamic equilibria for the formation of sodium tantalate and niobate with sodium hydroxide are analyzedat the temperature range of 400ºC to 700ºC. The apparent activation energy of formation,changes from 31.0±0.8 to 22.3±1.2 kJ mol-1 and from 23.8±1.2 to110.2±12.8 kJ mol-1, for tantalate and niobate, respectively. The reaction mechanism is examined on the basis of the analysis of reaction products using X-ray powder diffraction (XRPD) and X-ray fluorescence (XRF).

Jan 1, 2015

By K. Olsen

As aluminum alloy usage in automobiles grows, there are increasing demands on recycling processes and facilities to deal with mixed alloy automotive aluminum scrap. These processes and facilities strive to produce near virgin aluminum stock, which can be relatively costly and difficult. One alternative is to use physical processing methods to upgrade the scrap properties instead of chemically refining the scrap. The Impulse Atomization Process (LAP, patent pending) is a new process for making metallic and ceramic powders. It can produce fine homogeneous microstructures in scrap aluminum alloys due to high undercooling and rapid solidification. The particles have a very narrow size distribution and are in a convenient form for consolidation. This paper compares and contrasts the microstructural features of Impulse Atomized. and quenched Impulse Atomized powders,' for both AL6061 and a scrap aluminum alloy composition.

Jan 1, 1995

By Guo Xueyi

The electrochemical couple behavior of manganese dioxide with ferrous/ferric ions in acidic chloride medium was investigated, It was proven that the dissolution of Mn01 is due to the electrochemical couple reaction between MnO2/Mn2+ and Fe2+/lFe3+ in the solution, The driving force for the process originates from the rest potential difference of the two couples. The reduction of Mn02 is controlled by clectrochemical kinetics, whereas the conversion of F e2+ to Fe3+ is limited by diffusion, The factors such as the Mn2+, Fe2+, Fe3+, Cl concentration, pH of the solution and the temperature, have much influence on the kinetics of the couple process, This study will be useful to elucidate the mechanism for the leaching of manganese nodule from the deep ocean as well as manganese dioxide ores in land,

Jan 1, 2003

By Jun Zhu, Jilai Xuel, Tao Li

"Coal gangue is industrial waste containing Al2O3 and SiO2 with great recycling and reuse values. This work is aimed at extracting Al2O3 content in the coal gangue by a process of carbonthermal reduction - alkaline leaching. The Al2O3 and SiO2 contents first became a mixture of SiC and Al2O3 in the process of carbonthermal reduction, and then Al2O3 was separated by leaching in NaOH solution, thus producing the sodium aluminate solution for Al(OH)3 precipitation. The products generated at various stages in the process were inspected using XRD and chemical analysis. The effects of parameters such as reduction temperature, carbon ratio, NaOH concentration, leaching time, leaching temperature, stirring speed, etc were investigated in details.IntroductionCoal gangue is an industrial residue resulted from the process of coal mining and washing, accounting for 100 - 150 kg with 1 ton raw coal mined. The existence of coal gangue in large quantities has become a serious problem for environment pollution. On the other hand, the chemical compositions of coal gangue are Si02 and Ah03 primarily. In China, the accumulation storage capacity of Ah03 in coal gangue is not less than 600 million ton at a rough estimate, which should be considered as an abundant second resource [1]. If the alumina can be recycling and reused effectively from coal gangue, it will not only reduce the imperilments caused by coal gangue, but also yield good economic returns.Generally, the processes of extracting Al2O3 from coal gangue can be divided into acid leaching (vitriol or hydrochloric acid) and alkaline leaching (mostly NaOH) [2]. The acid leaching processes have many problems, such as lower leaching ratio, corroding the equipments, recycling the spent acid hardly, etc. The primary matter of alkaline leaching process is silica dissolving with alumina, which brings perplexing desilication process, alumina loss seriously and higher energy consumption."

Jan 1, 2011

By D. G. C. Robertson

The thermodynamics and kinetics of the reactions involved in fuming zinc from oxide slags using coal or coke were first studied in 1955 and have been the subject of many investigations since that time. The key reaction is ZnO(in slag) + CO Zn(g) + COl. This paper will review the some of the recent work, and will add new insights obtained in experiments carried out by the authors. In the first series of experiments it was shown that the reaction 2Fe2+ + ZnO = 2Fe3+ + Zn(g) or 2FeO + ZnO = Fe2O3 + Zn(g) does not occur at an appreciable rate, as is expected from thermodynamic considerations. In the second series of experiments it was shown that zinc does not fume from the slag at a significant rate unless a reductant has been added. This again is in accord with thermodynamic considerations, but is in contradiction to some of the experimental results reported in the literature. A third series of experiments was carried out with excess coke being present, so that the rate of supply of reductant was not in any way controlling the rate. The kinetics of zinc oxide reaction were then found to be independent of the zinc oxide concentration, but increased with increasing basicity, and temperature. The presence of high concentrations of FeO in the slag also improves the kinetics. At low zinc oxide concentrations iron oxide reduction occurred in parallel with zinc oxide reduction. We propose that (under the conditions of this work) the kinetics were controlled by a chemical step, namely the rate of desorption of an adsorbed CO2 species. This is the same mechanism as reported by Belton and co-workers for the kinetics of the reduction of FeO. This explains why the reduction of metal oxides in slags by hydrogen is often faster than by CO.

Jan 1, 2003