Search Documents

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By A. Warczok

The oxidation and smelting of chalcopyrite, bomite, chalcozine and pyrite has been studied under simulated flash smelting conditions. The results of copper sulphide oxidation show that under constant oxidation conditions, the degree of oxidation drops sharply when the particle size is increased above a given range. This critical size range varies typically between 200 and 500 pm depending on the oxygen content in the gas phase. For bomite, chalcopyrite and pyrite, the critical size range increases with increasing iron content in the mineral and with increasing oxygen content in the gas phase. The extreme case is observed for pyrite in pure oxygen, where there is no effect of the particle size on the degree of oxidization. Microscopical observations of the oxidized products show the influence of different factors on the mechanism of oxidation and fragmentation of the sulphide particles. Based on microscopical analysis and phase identification of the oxidized products, a model has been proposed for the oxidation and smelting of copper sulphide particles in suspended state. The mathematical model describing the sulphide particle oxidation is supported by the obtained results. Using this model, it is possible to describe the role of particular factors in the sulphide minerals oxidation.

Jan 1, 1992

By Shigem Kuramoto

Pure copper is known to exhibit intermediate temperature embrittlement when it is deformed at a slow strain rate, and a small addition of zinc suppresses this embrittlement. In the present study, the relation between zinc addition and hydrogen behavior was taken into account since the impurity hydrogen is believed to deteriorate the ductility at intermediate temperatures. Pure copper and Cu-l mass % Zn alloy specimens are prepared by melting in argon and in vacuum, so that a comparison can be made between the specimens with normal hydrogen content and those with' less hydrogen content. Tensile tests are performed at temperatures ranging from room temperature to 600 "C, and hydrogen behavior is analyzed using a newly developed testing machine that can detect gas evolution from the specimens during deformation and fracture in ultra high vacuum. The small addition of zinc to pure copper decreases hydrogen content, leading to the improved ductility at intermediate temperatures. In addition, the samples of both pure copper and Cu-1%Zn melted in vacuum exhibited higher ductility at intermediate temperatures than those melted in argon atmosphere, which is attributed to reduced hydrogen content.

Jan 1, 1998

By Keizo Uematsu, Kumiko Sanda, Nozomu Uchida

"Full understanding of mechanical properties is the most important assignment in ceramics. Establishment of defects-property relationship is crucial for fulfilling the assignment. This study reports detailed characteristics of defects and their relevance to the mechanical properties for alumina ceramics made through a typical industrial processing. Novel characterization methods were applied to evaluate their defects. A very simple direct correlation was successfully found between defects and properties in ceramics. This result is a great epoch in the field of ceramics. IntroductionThe ceramic materials are used in refractoriness, corrosion resistant materials and structural materials. The low fracture toughness and scatter of strength are very important problems in ceramics. The toughness of ceramics is lower than metal and polymer materials, and the allowed defect size is small. Very small internal defects (pore, crack, huge particle) can be a fracture origin in the brittle fracture. The characteristics of defects such as size, distribution and shape change markedly by process condition, which cause the scatter of strength. This study conducts quantitative evaluation and direct observation of the sizes, shape and a number of internal defects with a light microscope, and discusses the relationship for mechanical properties and defect sizes"

Jan 1, 2000

By G. P. Chaudhari, F. Warchomicka, M. Dikovits, V. Pancholi, C. Poletti

"The hot formability of a microalloyed steel with 0.16 wt-%C modified with N is studied by using processing maps. Compression tests of cylindrical samples are carried out using a Gleeble®3800 simulator in the range of temperature between 750 -1000°C and strain rates between 0.01-100 S-1. For this alloy, an Ar3-temperature about 740°C is determined by means of dilatometry. Processing maps are calculated using the modified dynamic material model developed by Murty and Rao for different logarithmic strains. For the instability map, the parameter Kj developed by the authors in previous works is used and compared with other instability values. Softening in the flow curves provoked by induced ferrite during deformation at low temperatures and low strain rates is reflected in the n-value. Light optical microscopy (LOM) and electron back scattered diffraction (EBSD) measurements are used to study the microstructure of the hot deformed samples to determine the deformation mechanisms active and to verify the processing maps.IntroductionProcessing maps offer a good possibility to optimize thermomechanical process parameters and to avoid defects in the products. Prasad et al. [1] developed the processing maps using the dynamic material model (DMM) and Murty & Rao [2] modified it. Processing maps consist of two superimposed maps: the dissipation efficiency and the instability map. The processing maps can be used to detect areas with a good hot formability, which are normally related to restoration of the material by dynamic recovery/recrystallization. For a high dissipation efficiency value and no instabilities, a good hot formability is predicted. In the DMM no storage of energy takes place and so the material is considered essentially dissipative, this is only true for high temperatures and high strain rates [1]."

Jan 1, 2012

By Ken Baxter

The Sepon Copper Project is located in Laos and has a mineable reserve of approximately 16Mt of ore grading 5% copper with minor gold and silver values. The deposit is a clay-hosted secondary copper mineral suite, predominantly chalcocitic in nature with associated pyrite. The current project design is based on the production of 60,000t/a of LME Grade A cathode by an acid leaching process followed by solvent extraction and electrowinning. Significant metallurgical testwork was conducted as part of the Definitive Feasibility Study (DFS) with process challenges identified and overcome at each phase of testing. Flowsheet configuration is geared to autogenously generating sufficient acid and ferric iron to meet gangue acid consumption and to leach the copper. The ability to maintain acid and ferric levels in the process liquors is strongly influenced by the proportion of pyrite in the ore presented to the autoclave. This paper will outline flowsheet development from preliminary variability testing to pilot plant and DFS design. The Sepon process solution seeks a balance between operability and capital/operating costs, and provides insights into the basic mechanisms influencing flowsheet selection for these ore types.

Jan 1, 2003

By Florian Kongoli

The so-called "fayalite" slag, despite problems associated with it, is the most widely used slag in copper smelting processes. Thirty years ago, in order to overcomes some drawbacks of this slag a new "calcium ferrite" slag was proposed especially for continuous copper converting. Since both slags have strong and weak points depending on the field of their application about 8 years ago another new "ferrous calcium silicate" slag was proposed that is expected to solve the drawbacks of each slag. This new slag is defined as mainly consisting of FeOx, CaO and SiO2 as its main components but it can practically have several combinations of these constituents. In order to determine the best area of this slag for possible industrial application the quantification of phase relations is an important subject. In this paper the work carried out by the authors in quantifying through an original physical model the phase relations, liquidus surface, liquidus regions, behavior of solid phases and the effect of minor components is reviewed. Several special compositions of this slag have been identified and discussed for possible applications in the industrial practice.

Jan 1, 2006

By S. Kang, D. G. C. Robertson

Slag cleaning furnaces require extensive wall cooling because they involve the use of a superheated slag bath. This is in direct contrast to smelting furnaces, where the wall is usually (but not always) protected by "banks" of solid charge. In order to understand the heat transfer and flow in slag cleaning furnaces a number of model studies have been carried out using molten wax to simulate the slag. Wax is a good model fluid because, like slag, it has a high Prandtl number. Wax models cannot simulate the behavior close to the electrodes (DC arc or AC submerged), but they can and do give a good simulation of the flow and heat transfer at the wall. An understanding of these phenomena is of great importance for the design of cooling panels in the walls of the furnace. Since superheated molten slag will eventually wear away any refractory bricks over time, the wall cooling must be designed to form a frozen layer of slag, referred to as a "freeze lining". The heat flux density (Q/A) required to do this is given by Q/A = h* ?T, where h is the heat transfer coefficient in the slag phase at the wall, and Li T is the superheat (bulk slag temperature - liquidus temperature). Both Q/A and h vary greatly with position and both are usually a maximum at the slag line. In the experimental work, molten wax baths were heated by block heaters to provide similar energy densities to those encountered in commercial slag cleaning furnaces. This procedure was considered to be valid since most of the electrical energy into a furnace bath is dissipated as heat. Gas stirring was used to simulate the gas evolved at the electrode in real furnaces - the quantity of this gas could be estimated from a knowledge of electrode consumption. The similarity criterion was equal gas flow per unit area of surface, in model and prototype. Heat transfer coefficients were measured in the models as a function of power density, gas stirring, superheat, etc., and could be related to the full-scale operations by the use of dimensional analysis.

Jan 1, 1999

By A. K. Kyllo, G. G. Richards

"The formation and control of accretions is an important aspect of process operation for gas injection. The nature of the accretion formed can have a considerable effect on a process, especially on the life of the lance or the refractories in the tuyere region. There are three basic shapes of accretion formed on tuyeres; pipes, hemispheres and hollow-cored hemispheres. However, there are wide variations within these shapes. Generally, the type of accretion formed will depend on the injector design, certain operating parameters and the physical properties of the bath materials. This paper seeks to collect the results of previous and current physical and mathematical modelling together with data gathered from operating furnaces, to obtain a better understanding of the effects of process design and operating variables on accretion formation.IntroductionAn important consideration in the design of a gas injection process is the possible freezing of the bath either around the tuyere or on the lance. With proper design, freezing may be controlled to provide protection of the lance or refractory, and to avoid blockage. Improper design may lead to tuyere blockage and significant refractory or lance erosion. In view of this, a good understanding of the heat transfer in the injection region is essential.While tuyere blockage has been a persistent problem since the inception of submerged gas injection processes, the problem of accretion formation was not studied in detail until the development of the shrouded tuyere by Savard and Lee. A number of studies relating to accretion formation have been carried out since then, but there is still little information available relating the nature of the accretion formed to the design of the injection system.The build up of materials on lances is a similar problem, and may also be either beneficial or detrimental, depending on circumstances. Unfortunately, there is even less information available regarding build up on lances than there is relating to tuyere accretions. While the form of build up on lances is generally a simple coating of the lance, accretions on tuyeres tend to be more complex. Tuyere accretions tend to occur in one of three basic forms: pipe, hemispherical and hollow-cored hemispherical (Figure 1). However, there appears to be a considerable variation within these forms."

Jan 1, 1996

By P. A. Davidson, D. J. Short

"In this paper we describe a 'non-contact' electromagnetic nozzle suitable for sprayforming and gas atomization processes. In such processes there is a need to control the flow rate and diameter of the liquid metal jet whilst minimising contamination of the stream. This can be achieved using an electromagnetic valve, which partially levitates the jet in freespace, using a segmented cylinder surrounded by an induction coil. This valve will significantly enhance the quality of the titanium alloys and nickel-based superalloys used in sprayforming and gas atomization. This paper describes the design and test of a laboratory prototype valve based on experiments performed with liquid tin.1. Introduction In many industries there is an increasing need for clean, high quality metals and alloys based on titanium and nickel. Two important processes are: 1) Spray deposition which allows the liquid metal to be converted to a near-net shape, thus alleviating the need for subsequent forging and extensive machining and; 2) Powder production of titanium by gas atomisation.In centrifugal spray deposition of titanium (see figure 1) the metal is induction melted in a cold crucible. The crucible consists of a number of water-cooled segments, which allows the high frequency magnetic field of the coil to pass through the crucible, and into the melt. The charge is melted by the induced eddy currents. Locally at the crucible walls the liquid metal solidifies, and is contained within a. 'skull' of its own solid, thus reducing contamination from the crucible wall. Once melted the metal is poured through an electrically heated graphite nozzle and into the spray forming chamber. The principal limitation of the process to-date, however, is that it currently uses a graphite and /or ceramic nozzle to direct the flow of liquid metal to the atomizing disk and as such there is considerable risk of nozzle erosion with inevitable effects in terms of contamination of the melt stream and variability in flow conditions. In this research programme we develop a. non-contact electromagnetic nozzle, which will totally eliminate refractories and/or ceramic materials from the melting and casting process. This will greatly enhance the technological capabilities of sprayforming and gas atomization processes."

Jan 1, 1999

By R. Winand, M. Degrez, C. Temmerman

"The influence of the copper electro crystallization inhibitors (mainly thiourea, gelatin and chloride ions) is studied in a new fully automatic pilot plan. This paper describes the conception and the building of this plan. The new approach is to reproduce the experimental conditions observed in the industry with the three additives present simultaneously in the electrolyte and secondly to study the influence of a slight modification of the concentration of one inhibitor, the others being present in the electrolyte with their industrial nominalconcentrations.1. INTRODUCTIONDespite the fact that gelatine, thiourea and chloride ions have been used in copper electrorefining for a long time, precise knowledge concerning their influence on the cathode deposit, metallographic structure and associated properties is still lacking.Many authors studied the influence of each additive separately, or of two added at a time. Only a few authors studied the combined influence of the three additives added simultaneously. The general conclusion that can be drawn is that the combined influence is far from that forseen from the influence of each additive separately, or even from two additives used at a time. Moreover most of the experiments described in the literature were performed by adding all additives at once initially. It is however, well known that gelatine looses a great part of its activity during the first half hour due to degradation by sulfuric acid (as shown by the cathode overpotential drop). Thiourea is rapidly replaced by a number of degradation mole,cules and complex ions including cations from the solution, changing even the equilibrium between Cu, Cu(I) and Cu(II).Chloride ions are consumed by precipitation.A number of successive research projects [1-9] led pregressively to the concept that, in order to obtain reproducible results representative of industrial cathodes, it was necessary to simulate as far as possible industrial conditions. It was essential that all additives were added continuously during the electrolysis, with, as consequence, a continuous bleed.The purpose of this paper is to describe the concept of a new fully automatic pilot plan for copper electrorefining and to present the first results."

Jan 1, 1997

By W. F. Drinkard

Many in the environmental movement have focused on this element. But, nothing they or anyone does will change the amount of arsenic in the world. This report is on actual commercial plants that we developed and operated to recover or stabilize arsenic values from metallurgical dusts from gold and copper pyro operations and arsenical gold bearing ores. When they were available gold and copper values were recovered. Our experience in arsenic extends over thirty years. My first corporation, Mineral Research & Development Corporation was the first in North America to manufacture the then new CCA (copper-chrome-arsenic) wood preservatives. This class of wood preservatives proved to be so effective that it made wood into an entirely new material of construction. It is not uncommon for wood properly treated with arsenical CCA preservatives to last for thirty; forty, and sixty years. Over a hundred years have been projected in some field tests. Hundreds of thousands of trees have been saved. Millions more trees would have been saved had environmentalists not decided that their arsenic phobia was more important than trees. There are several variations of CCA. The most popular is CCA-C. Its formula is: CrO3 . . . . . . . . . . . . . . . . . . . 47.5% CuO . . . . . . . . . . . . . . . . . . . 18.5% As2O5 . . . . . . . . . . . . . . . . . 34.0% Until recent restrictions were placed on the consumption of arsenical wood preservatives, annual consumption in North America was about 150,000,000 lbs./yr. About 64,500,000 of arsenic as the pentoxide was safely consumed this way. World CCA consumption has been about double the above figures or 300,000,000 lbs. as 100% CCA and 129,000,000 lbs/yr as As2O5. Close to 100% of all the arsenic used in wood preservatives is derived from gold or copper processing. The valence of arsenic required for CCA wood preservatives and many other markets is the same valence that is required for stabilization. The economic challenge is how to get there. We have built and operated eleven plants to oxidize arsenic trioxide to its pentavalent form. Most of these have been classic in that they used a common oxidants such as hydrogen peroxide or nitric acid to achieve this.

Jan 1, 2005

By Tatsuki Uzawa, Takashi Nagai

The consumption of Nd and Dy is increasing dramatically because of an exceptionally high demand for Nd-Fe-B-(Dy) magnets and a significant amount of the magnets are wasted. It is important to develop a recycle process the elements from the wasted magnets. In this study, Nd and Dy were extracted from the magnets by silver at high temperature. Nd can be extracted more than 70 % by silver. However, Dy is extracted only 25 % in the same experimental condition.

Jan 1, 2014

By Takeshi Azakami

By combining the iron reduction process with the usual rotary kiln process, the direct production of metallic zinc from EAF dust is proposed. After thermodynamic estimation and desk-top experiments it is confirmed that the process is hopeful under suitable conditions. In order to get some practical test data the enlargement of the process scale was planned and the bench scale tests were carried on successfully. In these experiments a zinc ingot of PW grade was produced from EAF dust.

Jan 1, 2003

By I. Hilario, D.Y. Medina, V.J. Cortés, J.D. Muñoz

The process of Tribofinishing is investigated as a memns to reacha state of quality for the surface teated. During the said process there occurs mass transferat the interface of the piece to be treated and the abrasive charge (abrasive plus additives). This stiuation is studied for Titanium as a possibility for application in prosthesis. With these results is intended to produce a model of the mass transfer that would allow having further control of the process.

Jan 1, 2012

By J. K. Brimacombe

"Nearly all the easy things have been investigated in injection metallurgy. Water models have been used exhaustively to study mixing, gas distribution and flow in submerged jets. Mathematical models have been developed with their restrictive boundary conditions to quantify submerged gas jet behavior. While being valuable tools to our understanding of injection metallurgy, there is an obliqueness to their application. What we need now are measurements and modelling on the actual systems, hot and unfriendly, where gas meets liquid at temperatures above l000°C. This is where the challenge lies.AN APPRECIATONThere are those who follow the trail and there are those few who blaze new trails in search of novel concepts and processes. With his restless, inventive mind, Howard Womer is a trail blazer without doubt. Decades ago, he was a pioneer in the pursuit of continuous steelmaking with the WORCRA Process and, today, he is developing new processes for the treatment of waste. He is not only an inventor but has been a professor at the University of Melbourne and was the first Director of Research at BHP. He has influenced the lives of many people, including myself; with his achievements and humanity. Therefore it is most fitting that this symposium should be held in honour of Howard Womer, a luminary in the metallurgical world for over half a century.BACKGROUNDGas injection has been an integral part of pyrometallurgical processes since the early days of Bessemer, then of Pierce and Smith. Today, of course, one cannot imagine pyrometallurgical processes without submerged gas injection to effect reactions for metal extraction and refining, to provide mixing and to inject solids into molten metal, slag or matte. Spurred on by new developments like tonnage oxygen and argon production, the Savard-Lee concentric tuyere and porous plugs, new steelmaking processes have emerged; and now solids injection is changing copper extraction processes. The ingenuity of the extractive metallurgists who drove these developments is inspiring for they have applied gas injection to transform pyrometallurgical processes. Humankind has been the beneficiary.' Today these processes are safer, more efficient, cost effective, less energy intensive and more environmentally friendly."

Jan 1, 1996

By Stein Tore Johansen

Some ferro-silicon furnaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the?off?gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels close to the furnace is observed. The result is irregular stops to clean the off-gas channels. The paper focuses on the nature of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By Stein Tore Johansen

Some ferro-silicon fumaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the off-gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels? close to the fumace is observed~ The result is irregular stops to clean the off-gas channels. The paper focuses on the nature? of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By Pedro Lobarinhas

In the present work a two dimensional computational model is derived for the description of the time dependent heap leaching process. The flow inside the heap is calculated using the diffusion equations for the flow in porous media. The soil conductivity is also estimated assuming a close packed structure for the grain packing inside the heap. These equations, with appropriate boundary conditions, are solved using a time step splitting scheme. From this calculation the amount of leaching reagent in contact with the ore at any position inside the heap can be calculated and, once coupled with appropriate reaction equations, the amount of metals extracted can be computed and leaching agent concentration updated. The model is tested with available experimental data and the results have shown to be in a very good agreement. The model predicts all the transient features of the data.

Jan 1, 1999

By Zhuoqing An, Qi Li, Zhancheng Guo, Yanling Zhang

Fluidized bed is an important iron-making reactor, especially for the finely sized iron-bearing materials. However, defluidization caused by sticking between particles extremely limited its wide spread commercialization. In this paper, apparent viscosity was put forward to express the ability of particles to resist movement, which is reasonably considered as the comprehensive results of interaction between particles. Meanwhile, an experimental measuring method of apparent viscosity of particles was proposed, during which the torque exerted on the rotating blade in a particle layer is measured, and then the apparent viscosity is obtained based on the motion equations of powder particles. Further, the apparent viscosity of iron particles was measured by using of this method, and the effects of shape, size, and temperature were examined. The data can provide important information for understanding when and why defluidization happened.

Jan 1, 2015