Search Documents

By K. Narayan Prabhu, W. D. Griffiths

"Heat transfer during the unidirectional solidification of a cast iron alloy against cast iron chills was investigated using an inverse modelling approach. Chills of thickness 100 mm and 10 mm were used, to simulate gravity die cruiting conditions and the use of chills in sand moulds. In both cases transient heat transfer, measured by the interfacial heat flux and heat transfer coeffieient; declined from initially high values in the first few seconds of solidification, to values about an order of magnitude lower which persisted for the remainder of the experiments. In the case of the thin chill it became saturated with heat until it was no longer in a position to extract further heat from ·the casting. These results were interpreted by studying the resistance to heat transfer from the casting offered by the ·casting-chill interface and the chill itself for example, the thermal resistance of the casting-chill interface can be influenced by the deformation of their respective surfaces and their subsequent relationship.IntroductionDie casting cast iron offers several advantages such as energy savings, higher mould yield, and better surface quality over the sand casting process1 • The process is· environmentally' friendly because of the elimination of the sand. However the design and construction of metallic moulds is expensive and a faulty die design may result in a defective casting: A simulation based process design of die castings would enable die designers and solidification modellings to try better designs of dies on the computer and arrive at a cost effective solution more quickly. This has numerous benefits for the die caster, as he would be able to produce sound castings with very short lead times.The success of a solidification model to predict accurately the thermal history and the location of hot, spots inside a solidifying casting depends to a large extent on the heat transfer data prescribed at the metal/mould interface. Many measurements of the heat transfer coeffident (or the heat flux) between a solidifying aluminum alloy and a chill have shown that the heat transfer coefficient is a function of most of the variables of the casting process2 - 8. However heat transfer studies during the solidification of ferrous alloys are rather limited. The high temperatures involved suggest that the contribution due to radiation heat transfer cannot be neglected."

Jan 1, 2000

By Ryokichi Shimpo, Akio Fuwa

"The process-measurements of copper smelters in Japan were investigated for the summary of the latest technique and for the fundamental study of process control. The smelters investigated are those employing flash smelting furnace and P.S. converter, one reverberatory furnace and P.S. converter, and one continuous smelting converting furnace (M.I. process). Respective process is then considered, consisted of several reactors of different functions. The measurement methods were summarized in each reactor, including the measurement points. The methods of chemical analyses of the samples in each reactor were also investigated.IntroductionAn investigation on the process measurements, chemical analyses, and system control in copper smelters in Japan were carried out for understanding and summarizing the technique of the pyrometallurgical copper smelting operations. The typical seven processes in six copper smelters were investigated in the period from 1985 to 1987. The smelters investigated were Touyo Smelter of Sumitomo Metal Mining Co., Ltd., Kosaka Smelter of Dowa Mining Co., Ltd., Saganoseki Smelter of Nippon Mining Co., Ltd., Tamano Smelter of Hibi Kyodo Smelting Co., Ltd., Ashio Smelter of Furukawa Co., Ltd. and Naoshima Smelter of Mitsubishi Metal Co., Ltd. They include five flash smelting furnace and P.S. converter systems, one Mitsubishi continuous smelting and converting process (M.I. process), and one reverberatory furnace and P.S. converter system.The investigation was performed by making inquiries about the measurements, chemical analyses, system control, and their future prospects to the engineers in each smelter and by summarizing up in each item. The system control and future prospects were summarized in another paper titled ""Process Control Scheme of Copper Smelting Processes in Japan and Future View."

Jan 1, 1989

By Nagahiro Saito, Takashi Nishimura, Takamichi Ichikawa, Akio Fuwa

"Yttria-stabilized zircohia (YSZ) has high potential to be used as solid-oxide fuel cell (SOFC) electrolyte. However, the high efficiency of SOFC has not been yet achieved due to the high internal resistance of bulk electrolyte. The resistance becomes lower with the decrease in the electrolyte thickness. Thus, the decrease in electrolyte thickness leads to lower internal resistance. . The aim of this study is as follows: (a) to prepare the thin films of YSZ by inductively-coupled RF plasma-enhanced metal organic chemical vapor deposition (PEMOCVD) process using Zr(t-OC4H9)4,Y(DPMh and oxygeil, and (b) to reveal the relationship between the structural characterizations and the process parameters.1. IntroductionYttia-stabilized zirconia (YSZ) has, been widely used as not only heat-resistant materials but also the components in automotive oxygen sensors, electrolytes of solid-oxide fuel cell (SOFC)(1)(2) and the buffer layers for the high-temperature superconductor because of its low thermal conductivity, good mechanical properties and high ionic conductivity. However, it is said that the internal resistance of the bulk electrolyte is too high to be appropriate as a solid electrolyte for high-efficient SOFC. The authors believe that the thin YSZ electrolyte can give a high performance to characteristics SOFC, since the internal resistance becomes lower with the decrease of electrolyte thickness. Thus the process technology to prepare YSZ thin films is desirable and must be established.In recent years, the YSZ thin films have been reported by chemical vapor deposition (CVD), thermal CVD using metal chlorides (MC) of ZrCl4 and YC(3)(4), thermal CVD using metal organic compounds (MO)(5)(10) Zr(t-OC4H9)4 and Y(C11H19O2)(11) and plasma-enhanced (PE) CVD using MO. Here, these methods are called MCCVD, MOCVD and PEMOCVD. MCCVD has two disadvantages; a large quantity of chlorinated impurities in deposited films and high processing temperature (> 1273K). This high processing temperature leads to damage of substrates in particular, so the application of this technology is limited. On the other hands, the processing temperature by MOCVD becomes and is lower. Unfortunately, the accurate vapor pressures of these metal organic compounds have not been, known so: that it is difficult to control the composition and the film thickness by MOCVD method well. Moreover, the large amount of carbonic compounds in the films prepared by MOCVD method is produced. However, plasma-effect has been reported to decrease large amount of the carbonic impurities by PEMOCVD. However, PEMOCVD has many reaction parameters in plasma processing; the geometry of experimental apparatus, radio frequency, electronic power input and so on. Thus, the general understanding about the relationship among reaction parameters, the composition and crystal structure of thin deposit film by this method has not yet been established."

Jan 1, 2000

By Kazuteru Tozcwa

The oxidation of several sulfide minerals in aqueous ammoniacal solution is discussed thermodynamically. The region in which Cu(NH3)2 4+ is stable has been estimated as a function of pH and concentration of total ammonia, {[NH3) + [NH4)}. In ammonia leaching when copper in sulfides is assumed to be extracted in the form of Cu(NH3)2 which will be rapidly converted to cupric ammine, thermodynamic data predict that such minerals are oxidized readily in the following order, CuS, Cu2S, CuFeS2, ZnS, NiS, Ag2S. This agrees with investigations on ammonia leaching of sulfide minerals, reported previously. The leaching of copper sulfide concentrate has been examined experimentally. Copper in a copper sulfide concentrate, in which the main constituents were chalcopyrite and pyrite, was effective¬ly extracted. The copper extraction was affected by factors such as (1) agitation intensity, (2) oxygen partial pressure, (3) NH3/Cu molar ratio, (4) leaching temperature and (5) addition of ammonium sulfate. From the results obtained in this work, it is concluded that mass transfer of oxygen plays the most important role in ammonia leaching of copper sulfide minerals.

Jan 1, 1976

By Chunlin Chen

Published data on thermodynamics of a number of minor elements (As, Sb, Bi, Pb, Zn, Se, Te, Cr, Sn) in liquid copper, matte and slag have been reviewed, assessed and used in development of thermodynamic solution models of melts. The behavior of antimony in alloys, mattes and slags is used as an example to illustrate the approach taken in assessment of published data and validation of the developed models with respect to the activity of Sb in condensed phases as well as the effects of matte grade, slag chemistry, temperature etc on the equilibrium distribution of Sb between melts and the gas phase. Results obtained from a comparison of different smelting processes with the modeled multi-phase equilibrium are presented and discussed. The predicted effects of slag chemistry and matte grade on the deportment of other minor elements during smelting of copper mattes will be presented and discussed.

Jan 1, 2006

By Katsunori Yamaguchi

The zinc, lead and alumina contents in copper smelting slag are increasing with the increase in waste recycling. The recovery of base metals such as lead and zinc from copper converter slag is important from both an economical and environmental perspective. As a fundamental study of the metal recovery by reduction process, activity coefficients of ZnO and PbO in the CaO-SiO2-FeOx-5mass%AlO1.5 slag under iron saturation at 1573K are derived from the data of slag-metal equilibrium experiments. On the basis of the obtained data, the activity coefficients of ZnO and PbO in the CaO-SiO2-FeOx-5mass%AlO1.5 slag were compared with those of the CaO-SiO2-FeOx ternary system. Addition of alumina increases activities coefficient of ZnO and PbO in SiO2 rich side of the slag, and decreases them in CaO rich side.

Jan 1, 2006

By Kimio Itagaki

As a fundamental study for smelting the copper matte with high contents of arsenic and antimony in a strongly reducing condition, phase relations between the liquid matte and copper-rich alloy phases in the Cu-Fe-S-As or -Sb quaternary system and between the liquid matte and iron-rich alloy phases in the Cu-Fe-S-As or -Sb system saturated with carbon were determined at 1473 K by a quenching method. Activities of arsenic and antimony in these systems were also measured at 1473K by Knudsen cell-mass spectrometry. Furthermore, distribution ratios of silver, gold and platinum between the liquid matte and copper-rich or iron-rich alloy phases were determined in relation to the arsenic or antimony content in the systems. On the basis of these data, the elimination of arsenic and antimony from the matte to the iron-rich alloy (speiss) and the recovery of precious metals in reduction smelting of the copper matte were evaluated. It was suggested that the addition of pig iron to make a strongly reducing condition and form the iron-rich alloy, which is fluid at smelting temperatures, will be useful for fixing arsenic in the speiss.

Jan 1, 2006

By J. Murphy

The economics of microbial coal desulfurization are affected significantly by the proper selection of the plant site and by maintenance of variables at suitable levels. High sulfur coal particles below 200 mesh show sulfate production rates triple those with 150 mesh coal but grinding costs are greater. Slurry solids density increases from 5% to 20% reduced the rate constant by a factor of 10. Coal added to a batch reactor in the stationary phase resulted in a sudden second exponential sulfate production phase indicating feasibility of lower cost continuous operation. Successful operation in the absence of beef broth, yeast or added nutrients at non-sterile conditions enhanced projected economics. Finally, the need for adequate agitation and aeration was well established.

Jan 1, 1985

By Raj P. Singh

Two design-of-experiments studies were carried out to investigate the leaching of technical grade molybdenum tri-oxide (TGM) in the presence of hydrochloric acid and the mother liquor of ammonium di-molybdate crystallization used as an ammonia source. Results indicated that leaching of TGM in HCl is possible only when used at about 1N concentration. In high concentrations of HCl, technical grade MoO3 had very high solubility (7.5 to 40 g/L Mo). The most suitable conditions for HCl leaching of TGM were obtained at a slightly elevated temperature of 80°C. Using about 1N HCl at 80°C, potassium in the leached solids (TGM) decreased to about 110 ppm, a value typically obtained in TGM leached in HNO3 - NH4NO3media (3.5 - 4.0 moles /L HNO3 + 0.5 ? 1.0 moles/L NH4NO3). Mo losses under these conditions were 0.8-0.9 g/L Mo. The HCl-leach method, presented here-in, has a significant advantage in chemical cost and environmental benefits over HNO3 ? NH4NO3 purification method.

Jan 1, 2006

By Yong .. Jun Wu

Laminated ceramics have received widely scientific and commercial attention because their properties, such as mechanical properties and electrical properties, can be tailored by adjusting the structure, thickness and composition of the different layers. For example, ferroelectric Bi4Ti3O12 (BIT) which has a positive temperature coefficient of dielectric constant (,E) can be used to modify the negative tE of typical microwave dielectric ceramic BaNd2Ti4O12(BNT), However, BaNd2Ti4O12/Bi4TiO12/Bi4Ti3O12/BaNd2Ti4O12 (BNT/BIT/BNT) laminated ceramics could not be prepared by the general method because the optimal sintering temperature of BaNd2Ti4O12 ceramic (around 1350°C) was much higher than that of Bi4Ti3O12 ceramic (around 1100°C). In this research, a new method of spark plasma sintering (SPS) combined with post-sintering was successfully proposed to prepare BNT/BIT/BNT laminated ceramics. It was divided into three steps. In first step, the BaNd2Ti4O12 ceramics were prepared by conventional sintering method. In second step, the calcined and pre-pressed Bi4Ti3O12 powders were sandwiched between BaNd2Ti4O12 ceramic pellets and spark plasma sintered at 900°C for 10min to synthesize BNT/BIT/BNT composite ceramics. In the last step, a post-sintering was employed to reoxidize the partially reduced BNT/BIT/BNT composite ceramics. The results of scanning electron microscopy (SEM) and electron probe microanalysis (EPMA) showed that BNT layer and BIT layer were well bonded and no significant interfacial infiltration between them was observed. The sandwiched BNT/BIT/BNT ceramic with 10.7% BIT in volume has a dielectric constant of 92.85, a low dielectric loss of 01068 and a small temperature coefficient of dielectric constant of 35 ppm/°C at MHz.

Jan 1, 2003

By KNona C. Liddell

The time and spatial dependence of component and species concentrations during in situ uraninite leaching have been modeled using a reactive transport model based on partial equilibrium between reactive minerals and the solution. The flow field is represented by mixing cells in series. The effects of the H2O2, (NH4)2CO3, and NH4HCO3 component concentrations have been simulated, and results are presented for a one-dimensional flow field.

Jan 1, 1995

By llya Perederiy, Vladimiros G. Papangelakis, Indje Mihaylov

"Nickel slags obtained from various smelting furnaces and converters differ in terms of their chemical composition and microstructure. The microstructure of the slag is largely affected by how fast the slag is cooled after being discharged from the furnace. Slow cooling is known to promote crystallization and growth of phases such as crystalline fayalite (Fe2Si04), magnetite (Fe3Ü4) and vitreous silica (S1O2). Slag granulation causes rapid solidification of the melt in the form of either an amorphous solid or highly intergrown crystalline silicate and oxide phases. Smelter slags contain entrapped Ni, Co and Cu in the form of dissolved oxides and matte inclusions. Extraction of the entrapped metals by high pressure oxidative acid leaching (250°C, 70 g/L initial H2SO4, up to 90 psi O2, 45 min) relies on the dissolution of the metal bearing minerals. The impact of the slag microstructure on the accessibility of these minerals to leaching, as well as the morphology of the produced residues is discussed in this paper.IntroductionIt was shown previously that entrapped base metals can be efficiently extracted from naturally cooled (as opposed to granulated) crystalline nickel smelter and converter slags using high pressure oxidative acid leaching operating at 250°C, ~40 g/L terminal acid and 60 to 90 psig oxygen overpressure [1, 2,3,4, 5, 6].Mineral characterization work performed on a naturally cooled crystalline nickel furnace slag from Vale's operations in Sudbury (ON, Canada) was previously reported [4]. Fayalite (Fe2Si04) and magnetite (Fe3U4) were detected using powder X-ray diffraction. These two minerals as well as silica (S1O2) and matte ([Fe,Ni,Cu]Sx) were also identified with the help of energy dispersive X-ray spectroscopy (EDX) on cross-sectional images obtained with a scanning electron microscope (SEM) operating in the backscattered mode. Nickel converter slags obtained from Vale's operations in Sudbury were found to be mineralogically similar to the furnace slag, but with higher contents of matte entrainment and magnetite based on the SEM-EDX observations [6]."

Jan 1, 2012

By M. Huang

A conductivity-based sensor for on-line measurement of free acid was recently built. This sensor is suitable for high ionic strength solutions and its corrosion-free operation is based on induction currents. It has been tested against literature data and measurements made using a previous developed contact-type conductivity cell, with an average difference within 1%. The electrical conductivities of H2SO4?H2O, H2SO4?MgSO4?H2O and NaCl?Laterite-H2Osolutions at temperatures up to 250 °C were discussed. It was found that the solution conductivity depends on various factors, such as the electrolyte concentrations, the type of electrolytes, temperature and the amount of dispersions. A semi-empirical model was developed to account for all the factors discussed. This model was further tested on actual process solutions from the hydrometallurgy of nickel where sulphuric acid solutions containing a variety of metal sulphates and solids. The average difference between the estimated acid concentration from this model and the one from titration was generally less than 5%, which is excellent for industrial applications.

Jan 1, 2006

By Fuqiang Zheng, Feng Chen, Wenting Duan, Yufeng Guo, Tao Jiang

High-quality titanium-rich material is of significance in the development of titanium industry as it is the main raw material to produce sponge titanium and titanium white using chloride process. Activation roasting of titanium slag with high Ca and Mg contents as adding H3PO4 followed by acid leaching was investigated to prepare titanium-rich material. The effects of H3PO4 dosage, roasting temperature and time, hydrochloric acid quantity, acid leaching temperature and time on TiO2 grade and removal of impurities were studied. The results show that after the finely ground titanium slag roasted with 8% H3PO4 at 1000 for 2h, most Mg impurities in anosovite solid solution structure were converted into simple acid–soluble compounds. The impurities such as Ca and Mg obviously decreased when the hydrochloric acid concentration was 20%, leaching at 100 °C for 2h, from which a titanium-rich material containing 82.56% TiO2 and 1.15% (CaO+MgO) was obtained.

Jan 1, 2016

By P. Chris Pistorius

"Ilmenite smelting involves partial reduction of iron oxide from a slag consisting mainly of T1O2, T12O3 and FeO, yielding as products iron (with approximately 2% carbon) and titanium slag. Slag purity requirements preclude any fluxing additions, and the aggressive nature of the slag necessitates a furnace freeze lining. Large departures from thermal and chemical equilibrium hold in the smelter, with possible implications for process stability. The slag is approximately 150K. hotter than the metal, which means that the metal temperature is below the slag melting point; this difference in temperature has been shown to lead to formation of a solid TisOs-rich layer between the slag and metal. Recent equilibrium measurements have confirmed that the slag and metal are not in chemical equilibrium either, with significantly more reducing conditions in the metal than in the slag. After solidification, the pseudobrookite slag structure is metastable below approximately 1400K, and may transform upon slight oxidation.IntroductionThe natural mineral ilmenite is the main source of titanium, which is mainly used to produce Ti02-based pigments. Ilmenite has the ideal formula FeTiC>3, but natural minerals can be partially oxidized (to contain some Fe3+), and typically contain MnO and MgO as well, together with associated silicate minerals. Smelting is one of the methods to upgrade ilmenite for subsequent T1O2 pigment production; smelting involves partial reduction of FeO to form metallic iron as a byproduct and titanium slag as the main product. Reduction is typically controlled to yield a slag which contains around 10% FeO, 85% (Ti02+Tij03) and 5% impurity oxides (mainly MnO, AI2O3 and S1O2). An example of a typical average slag composition from reduction of South African ilmenite is shown in Table I. As this indicates, a significant side reaction is reduction of some T1O2 to T12O3. The relative extents of reduction of FeO to Fe and of Ti02 to T12O3 are such that the slag stoichiometry is close to that of the pseudobrookite phase [1]. Pseudobrookite has the structure AB2O5 (where ""A"" and ""B"" are different cation sites); the phase which makes up the bulk of solidified titanium slag has the AB2O5 structure and stoichiometry [2], and can be viewed as a solid solution of FeTi20s, T13O5, ÌçÔÀ2è5, MgTi20s, AI2T1O5 and C^TiOs [1]. This solid-solution phase is referred to as ""pseudobrookite"" or ""M3O5"" in this paper."

Jan 1, 2012

By Lucas Nana Wiredu Damoah, Lifeng Zhang

"Increasing demand for Solar Grade Silicon (SoG-Si) due to rising interest in renewable energy has lead to increased SoG-Si Top – cut scraps generated from the multi-crystalline silicon making process. Due to the high cost of SoG-Si and the potential to use the top-cut scraps as feedstock material, there has been increased effort to develop cost effective and efficient technologies. As a result, several methods to recycle the top-cut scraps are currently been applied, and researched. These include settling under gravitation field, which is a slow process to be industrially applicable. Natural settling of inclusions by gravitational force is a slow process and not attractive to the industry. Recent experiments on Top-cut SoG-Si scrap under high frequency, high voltage, electromagnetic field showed that SiC inclusions settled within a short time to the bottom of the crucible and the characteristic rod-like morphologies of Si3N4 inclusions in SoG-Si were not detected. This study investigates the enhanced settling of SiC inclusions and the behavior of Si3N4 particles under the influence of high frequency, high voltage, electromagnetic field in Top-cut SoG-Si.IntroductionThe photovoltaic industry depends on silicon based PV materials either as single-crystalline silicon, or multi-crystalline Si (MC-Si), or amorphous Si [1] for over 90 % of its market share. [2] MC-Si produced by directional solidification of solar grade silicon melt dominates the silicon PV market. During the directional solidification process, SiC and Si3N4 particles within the melt are pushed by the solidification front to the top of the ingot which is the last to solidify. Therefore the top of the ingot is cut generating what is known as top-cut solar silicon scraps. The Si3N4 particles are mainly from the coating material at the inside surface of the silica crucible and from air absorption during the solidification process. The SiC particles mainly stem from the carbon reduction process of the primary production of silicon [3]. Due to the growth of the PV industry as a result of global demand for clean, reliable, and affordable energy [4], there is the need to develop new methods to compliment exiting ones to recycle SoG-Si waste (e.g. top-cut) for sustainability."

Jan 1, 2012

By Henk Dijkman

Existing metallurgical operations can be optimized by implementing engineered bioreactor systems in the process configuration. For instance, metals can be recovered safely and economically from process and waste streams using biogenic sulfide. This paper focuses upon possible applications of high rate biotechnology in metallurgy and mining. Metal recovery from liquid streams (process bleed streams, leach water, waste streams), integrated removal of (fugitive) SO2, treatment of acid blowdown and other options will be described. Practical examples are given. A large-scale application of biotechnology at Pasminco's Budel Zink refinery is described. Here, acid plant blowdown is treated together with electrolyte magnesium bleed. Concentrated zinc sulfide (10 tpd) is produced biologically, eliminating the production of gypsum and closing the refinery sulfur cycle. Recovery of metals from solution at Kovehute Pribram in the Czech Republic is the second practical example. In this case, H2S is produced on-site for metal removal from an alkaline slag dump leachate. At the Caribou mine in New Brunswick, Canada, acid mine drainage is treated with biogenic sulfide. This plant is situated upstream of a lime neutralization plant. As a result, reusable ZnS is produced, the volume of the sludge (gypsum and hydroxides) from the lime plant is reduced by 50%, the sludge is free of heavy metals and the final effluent concentration of heavy metals is in the ppb range. In the second phase of this project, metals will be recovered from stored tailings, resulting in significant revenues.

Jan 1, 2002

By Guozhu Ye, Mikael Lindvall

"Swedish iron ore contains about 0.1 %V. The vanadium is reduced to the hot metal in a blast furnace and oxidised to the slag in a converter. The high V-content, up to 5 % V, leads to a very limited external application of the steel slag in Sweden. Since 2004, MISTRA - the Swedish Foundation for Strategic Environmental Research has together with the steel and mining industry in Sweden and Finland initiated and supported a long term project aiming at efficient recovery of vanadium in the slag, and at the same time a useful slag product with low V-content. The proposed concept consists of a reduction step and a phosphorus removal step. This paper will highlight some of the results with focus on the various metallurgical reactors used for slag reduction, including results from recently performed pilot trials using a DC furnace for cotreatment of metallurgical slags and other wastes.IntroductionToday, less than half of the produced LD-slag in Sweden is recycled to the blast furnace as a lime source and the rest is temporarily stored inside the steel plant. The steel slags cannot be used externally due to its content of vanadium and free lime. As the slag storage area is limited, this has become a problem for Swedish steel producers. The disposition of the slag is also a great waste of a valuable vanadium resource. The current potential value of vanadium in the discharged steel slag annually amounts to roughly US$ 100 million. Currently, Swerea MEFOS is conducting an 8-year vanadium recovery project called VILD (Vanadium in LD-slag) aiming at efficient recovery of vanadium and at the same time producing a useful slag product with low V-content. The project is financed by MISTRA - the Swedish Foundation for Strategic Environmental Research and the steel and mining industry in Sweden and Finland. Various reactors and process options have been tested in the past 7 years, from 3 kg laboratory scale, 150 kg induction furnace, 3 MVA pilot DC furnace, 5 MVA pilot AC furnace, 5 tons Kaldo furnace, to full scale direct hot slag reduction in the industrial site (12 tons of slag). This paper will introduce the VILD-concept and review the experiences gained from these trials. The advantages and disadvantages of the different options will be discussed and concluded."

Jan 1, 2012

By P. C. Guillaume

Global plant modernizations or expansions cannot be considered in the same light as any other industrial investment project. Relationships between the partners, relationships and communications with the client, structure and organisation of the teamwork, schedule of the work, and a lot of other tasks and missions devoted to external contractors have to be defined considering one fundamental input: an operating plant. For an engineering company expert in processing, like UM Engineering, such a context requires a specific approach as well as specific procedures able to efficiently challenge the generated constraints. First of all, even if a detailed audit had been conducted at the beginning of the conceptual engineering phase, new elements will be discovered during the preparation and realization of the project, and must be continuously integrated. Consequently, a close proximity to the site is necessary. This is one reason why UM Engineering, most often, works in partnership with a local engineering company. The second important point for the client is that the operation must not be interrupted during the realization. In order to make that possible, UM Engineering has defined a specific project structure and organisation, integrating on a permanent basis the operators (the "users") in the project teams. This paper presents the way UM Engineering copes with this type of "multi-constraints" context with reference to the recent copper cellhouse modernization under realization for the CCR Refinery of Noranda Inc. in Canada.

Jan 1, 1999

By Shun Fujieda, Shigeru Suzuki, Kozo Shinoda, Tetsuo Fujita

"Dowa's scorodite, synthesized by oxidation of Fe(II) ions in the presence of As(V) ions at atmospheric pressure, was characterized. The scorodite was well crystallized and had a very low solubility. To examine the conditions for stable storage of the scorodite for long periods, experiments with various synthesis and leaching conditions were done. The scorodite had a very low arsenic solubility in sea water. It was estimated in consecutive leaching tests that the arsenic concentration would eventually converge to zero. The prevention of arsenic leaching by adding goethite or ferrihydrite was limited in some cases. Very low toxicity was confirmed by toxicity tests. The investigation results suggest that disposal at a specifically designed well-controlled storage place is preferable for the scorodite whose toxicity had been made sufficiently low. Disposal to an isolated final disposal site with more stringent prevention for the outflow of toxic substances was thought another option.IntroductionArsenic is a considerable environmental concern. A system of technologies for the effective immobilization, storage and final disposal has been sought. Dowa Metals & Mining Co. Ltd. has developed a unique scorodite synthesis method (DMSP®) which works at ambient pressure [1]. The scorodite is precipitated by oxidizing Fe(II) ions in a high-concentration As(V) solution. The scorodite produced in this way does not readily release arsenic because of its high crystallinity. Final disposal is necessary because scorodite currently has no commercial value. A standard method for the final disposal of scorodite has not been established because its long-term stability under various conditions has not been fully examined."

Jan 1, 2012