Search Documents

By Collin L. Stewart

A summary of the results of a limited subsidence monitoring program at Cyprus Amax Coal Company's Shoshone Mine No. 1 in the Hanna Basin of south central Wyoming is presented. The monitoring program was designed to meet regulatory requirements for confirmation of subsidence predictions made in the mining permit. The longwall panels were 380 ft to 600-ft wide. Mining heights varied from 11 ft to 13.5 ft. Gate road development included three-entry and two-entry head and tail gates. Overburden depth varied from 150 to 945 ft. The coal seam and overburden dip at approximately 11 degrees. The overburden is very low to low strength mudstone and carbonaceous shale with low to moderate strength, silty sandstone interbeds. Panel W/h ratios varied from subcritical to supercritical. Smax was 0.9 of the mining height. The subsidence ratio was about 0.6 for subcritical width. The draw angle on the up-dip side averaged 20 deg. The draw angle on the down-dip side averaged 12 deg.

Jan 1, 1995

By Rene Rodriguez

The initial results of our investigations on the applicability of geophysical exploration methods to map coal seam inclusions were summarized in a paper submitted at the Thirteenth Conference on Ground Control in Mining in 1994. These investigations were continued under a variety of conditions at a number of underground coal mining operations. The results have been encouraging and have fostered a much more detailed understanding of the geophysical principles at work in underground mine mapping. This report summarizes a particularly interesting application, that is, the use of Underground In-Seam Seismic exploration methods to identify and to approximately delineate coal seam inclusions within longwall panels. The methodology relies on the excitation of seismic sources in the coal seam along one side of the panel and the recording of seismic waves by geophones secured to the coal rib on the opposite side. Head-Body waves (compressional and shear), direct and channel waves are generated in the process. While the head waves are critically refracted waves traveling at the coal floor and roof, direct and channel waves are transmitted through the coal body and are dispersive in character. Tomographic techniques applied to the velocity inversion of first arrivals permits a fast mapping of coal seam inclusions in the panel. The process incorporates path velocity and geostatistical intersect analysis. Full wave analysis of the dispersive channel waves, provides an independent and confirmatory information of the coal geometry, including the inclusions within. The inversion technique in this case is the modal analysis of the wave trains. The application of this method to three different problems was confirmed by subsequent mining of the predicted anomalies, proving the accuracy of the technique within limits of experimental error.

Jan 1, 1995

By John C. Stankus

ldentifcation of potential roof problems in coal mines has long been a complex issue due to the wide variety of mining and geological conditions. It is well known that mine roof falls are related to many different factors such as roof strata properties, sandstone channels, regional and localized horizontal stress, vertical stress, and tectonic stress. Many times, a combination of these factors causes roof problems. Through years of ground control experiences, Keystone Mining Services LLC, (KMS) has developed a Roof Instability Rating (TUR) system to predict potential roof problems. The first RIR analysis was presented at the 19th Ground Control Conference (Watts, et al., 2000). The RIR system includes: quantifying each individual factor, weighting each factor, combining individual factors, finalizing the RIR, and setting the criteria for the areas where special support is needed. In this paper, the application of the Roof Instability Rating (RIR) system at Enlow Fork mine will be presented.

Jan 1, 2001

By Herryal Anwar

The application of roof bolting technology to control the stability of roadways in coal mining within weak strata or under high ground pressure has improved progressively. One of several factors that affect the design of rock bolting is the immediate roof characteristics of the roadway. On the competent rocks, the mining conditions may indicate a high level of stability and a low density of bolting patterns may be adequate to control the ground stability. However, at a weak strata, the roadway will be affected by both horizontal and vertical stresses that may generate a high level of deformation in the immediate roof. This sensitivity of the roadway will require a mine plan design which consider the pillar sizes and sequences of extraction as well as a conservative reinforcement to maintain the integrity of the deforming weak roof strata. Rock bolting technology has been used to maintain the stability of roadways in Indonesia and Japan for a few years. In this paper the overview of the application of rock bolting reinforcement in Ombilin Coal Mine, Indonesia and Miike Coal Mine, Japan is given.

Jan 1, 1999

By David C. Laurence

in March 1999, the School of Mining Engineering at the University of New South Wales carried out a series of underground trials using " Evermine", a South African developed two-part water based polymer membrane. The aim of the trials was to determine the potential of a spray-on polymer membrane such as Evermine as an alternative to conventional rib support systems The mine selected was Angus Place colliery, reputed to have some of the worst ground conditions of any Australian underground coal mine. Ribs at Angus Place are supported by conventional pattern bolting supplemented by wire mesh. The trials indicate that there is significant potential for the introduction of polymer membranes into the underground coal minim; industry Initial results indicated that ribs that had been sprayed exhibited less displacement and spalling than unsprayed ribs. particularly when subjected to abutment loads from an approaching long-wall Further research will he required to conclusively rate the performance of Evermine in comparison to other products in the market and the long term performance of the product

Jan 1, 2000

By Lu Jiam Zhang

Coal and gas outburst is one of the serious natural disasters in the coal mines of China. Since 1950, more than 10,000 coal or gas outbursts have occurred in more than 200 underground coal mines of different types. The outburst prone coal mines are widely spread out. It occurs in different types of coal -ma and is very serious in some areas. Most outbursts occurred at the time of roadway driving in coal seam, serious outbursts occurred mainly when entering the coal seam during the cross-cut driving; of the outbursts, coal and gas outbursts We UP major proportion, while pressing out and pouring out ah account for a large proportion; outburst. occur under different operating conditions, but mostly occur during shotfiring. This paper introduces the prevention and control measures as practiced in China and illustrates the three types of outburst cla8sification. Both technology and management are equally important in outburst prevention and control. Measurement of the volume of drilling cuttings and the initial gas outflow rate fm- boreholes have proven to be effective. A special team and organization must be set up to deal with the problems.

Jan 1, 1987

By Joachim Leonhardt

Hundreds ofbolt-indicators were already used successfully in the German deep hard coal-mines to increase the safety and economy. The bolt-indicator offers the simple possibility to show roof-bolt (anchor-) loads. to indicate weak points as well as to optimize the anchor density and the dimension: The bolt-indicator is mushroom shaped and consists of coated metal. It is inserted between the anchor plate and the flanged nut. The loads appearing at the anchor are transferred to the bolt- indicator and can be recognized visually at the cylindrical part by the amount of the surface coating. Examples are used to clarify the application aims, operation and usage of the bolt-indicator and its yielding advantages in practice.

Jan 1, 2001

By Lorraine Kent

Comparison of in-situ stress overcore measurement results with those determined from laboratory evaluation of Acoustic Emission (AE) testing on oriented sub-core samples has been carried out for a variety of mining environments. These include UK and German Coal mines at moderate depth, shallow-level South African Coal mines and deep-level South African gold mines. Results show that the `Kaiser Effect' or 'Stress Memory-Damage is readily determinable throughout the brittle deformation process, although particular care is required in interpretation of results during the 'bedding-in' phase of testing and the region associated with unstable crack growth prior to failure. The results suggest that AE provides a useful complimentary method for comparison with existing methods of stress determination. The success of the method can, however, be dependent on both rock type and the likely magnitude of in-situ stress in comparison to the strength of the rock. Keywords: in-situ stress, acoustic emission, Kaiser Effect

Jan 1, 2002

By Peter Cain

In 1993 an opportunity presented to monitor the effects of undermining an abandoned roadway by a longwall panel in the Sydney. N.S. coal field. Interaction subsidence data was collected by survey leveling to benchmarks in the undermined gateroad as well as by a standpipe system equipped with 15 vibrating wire piezometers measuring changes in elevation in the gateroad relative to an outby header tank. The piezometers were monitored at 30 minute intervals using a datalogger. while the leveling surveys were conducted weekly over the life of the project. The monitoring program resulted in the collection of a very large both of data. relating vertical subsidence to the relative position of the underlying face. The most basic analyses derived a travelling subsidence curve from the leveling data only. which hinted at a relationship between rate of extraction in the panel below and the amount of strain developed in the undermined strata. The complexity of the relationships between the amount of subsidence obtained, the location of' the individual monitoring stations, the rate of face advance below and the potential for "periodic" subsidence due to geological conditions has made analysis difficult. and the amount of data has compounded this problem. Recently. an analytical approach using a commercial neural network analysis package has been applied. which appears to have resulted in the ability to draw sonic meaningful conclusions from the data set. In this paper a short history regarding the collection of the data set is followed by a brief' description of neural networks. This is followed by a description of the several analyses performed. some of the results obtained, and conclusions drawn.

Jan 1, 1998

A two-dimensional time-dependent analysis of a overburden-coal pillar-weak floor strata interaction problem is presented as a beam model consisting of a composite roof beam resting on multiple elastic foundations (pillars) underlain by a composite rock mass representing immediate floor strata. Several different material models may be considered for the immediate floor strata. The analysis can include all openings and pillars in a panel and permits bed separations in the roof composite beam. The model has enabled identification of the relative significance of different geometric and mechanical behavior parameters which govern the system. The paper presents the theoretical background for the model as well as its application to a mine in Illinois where surface and underground geotechnical observations have been conducted over the last two years.

Jan 1, 1988

By Aarao de Andrade Lima

Mechanical properties typical of coal are used in the comparisons of pillar strengths based on finite elements and the empirical equations of Holland-Gaddy, Salamon-Munro, Obert¬Duvall, and Bieniawski-PSU. A correlation among the strength parameters which are employed in the empirical equations, in Mohr-Coulomb and Hoek-Brown failure criteria is established. Emphasis is given to the important distinction between the mechanical properties of small rock specimens and those related to the rock mass. An elastoplastic version of Hoek-Brown criteria has been developed and implemented in a finite elements code. The strengths calculated using the empirical equations showed a good agreement when the ratio width by height of the pillars varied from I to 8, except for Holland-Gaddy equation which exhibited lower values. Under the hypothesis of associative perfect elastoplasticity used, pillar strength calculated using Mohr¬Coulomb yield criterion became excessively high for all the models having a pillar width by height ratio above 2. The finite elements solution based on Hoek-Brown criterion predicted strengths around fifty percent larger than Bieniawski-PSU equation when the pillars width by height ration varied from 3 to 8, showing good agreement below that range. It has been concluded that, under the hypothesis of percfect plasticity, stress analysis techniques may overestimate the strength of rock structures subjected to high confining stresses.

Jan 1, 1997

By Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to he abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1.000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

Jan 1, 2000

By Hamid Maleki

During the last decade, a significant amount of research has been conducted by Energy West Mining Company, government agencies, academia, and consulting companies to develop predictive tools for assessing the stability of the Castlegate Sandstone, which is found approximately 250 m above multiple-scam coal reserves, Energy West Mining uses longwall mining techniques in its operations near Huntington, Utah, and these studies were initiated to satisfy requirements for maintaining the stability of the Castlegate Sandstone and resource recovery. In this study, the authors have used multiple-regression analysis techniques and a wealth of data collected over many years on geology, mining, and escarpment stability. The volume of failed rocks is used as the response variable after several other factors were considered, including measurement of surface deformation and frequency of mining-induced surface fractures. Geologic and geometric variables were obtained along 3.7 km of escarpment exposure at 130 study locations. Regression analysis of data for the first 29 study location, which had been fully' undermined, showed that surface topography played a critical rule in influencing escarpment stability. Preliminary regression analysis results from 70 study loca¬tions identified several other important geologic arid mining factors that influence be stability of the sandstone escarpment These are canyon slope, sandstone thickness, and mining influence ante.

Jan 1, 2000

By Stephen Tadolini

Reduction in the time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. While this concept is not without controversy and risk, the rewards can result in substantial reductions in longwall face move/set-up times and provide safer working conditions. Both of these factors can reduce mining costs and enhance profitability in a competitive market. This project was even more complex because the longwall system operates under a weak roof condition. To examine the feasibility of this concept, a 16-ft wide by 170-ft long experimental pre-driven recovery room was designed using analytical, empirical and 3-dimensional finite element modeling techniques. Based on the projected loading conditions, immediate and main roof geological and strength characteristics, a variety of roof bolt types were selected and installed in the recovery room and adjacent chutes. To supplement the intrinsic supports, high-capacity roof-to¬floor cuttable cribs were strategically placed to reduce the potential of a weighting failure before the longwall shields safely entered the room. To evaluate the behavior and final support performance, the recovery room and chutes were instrumented to monitor the physical response during various loading phases. Additionally, the cuttable cribs were instrumented to evaluate the loading and stiffness characteristics during the extraction process. This paper describes the successful design process, support methodology, monitoring results, final observations and recommendations.

Jan 1, 2002

By Hanjie Chen

Mining experiences have shown that in a pitching seam, roof behavior is significantly different from a flat seam. Uphill mining usually experiences more roof problems than downhill mining. Based on a case study at RAG American Coal Company, Willow Creek Mine, this paper presents the roof control problems experienced in a high pitching seam. Then, finite element modeling is conducted to analyze the roof stress distribution for an entry developed in different directions relative to the seam strike. The results shows that seam inclination has a significant effect on roof stability in terms of tensile stress. Uphill mining experiences higher tensile stress than downhill mining. The modeling technique utilized in this analysis presents a first of kind methodology.

Jan 1, 2000

By David Newman

The Southern Appalachian coalfield has a long history of coal bumps that are attributable to a unique combination of topography, geology, and multiple seam mining. The high pillar stresses that generate a coal bump result from: i. mountainous topography where the overburden commonly exceeds 1,500 feet beneath ridges, ii. multiple seam mining, iii. thin interburden between active and abandoned mines, iv. thick beds of competent sandstone and sandy shale strata throughout the stratigraphic section, v. strong coal seams, and vi. irregular pillar and mining geometry in older room-and¬pillar mines. Coal has been intensively mined for more than 100 years in Eastern Kentucky, Southwestern Virginia, and Southern West Virginia. As a result, it is commonplace to have abandoned mines above and/or below active operations. Therefore, those conditions that generate coal bumps will be more prevalent in the future, as underground mining continues in Southern Appalachia. The focus of this paper concerns two coal bumps that occurred in the Kellioka seam where both undermining and overmining had occurred. The purpose of the investigation is to determine the magnitude and distribution of vertical stress that initiated the bumps, to identify bump-prone areas in the unmined reserve, and to recommend pillar centers and mining layouts to avoid future bumps. The state of stress in three vertically adjacent seams was examined using the LAMODEL boundary element program. Large, detailed numerical models were constructed of both bump areas and of the remaining unmined reserve block. The results of the numerical analyses were compared with those obtained using analytical equations.

Jan 1, 2002

By Klaus-Dieter Beck

RAG American Coal Holding, Inc. affiliates operate two longwall mines in the Pittsburg seam in Pennsylvania, the Cumberland mine and the Emerald mine. A unique situation in longwall operation occurred at these mines as the mining activities reached the property boundary between the two mines. The retreat direction in the longwall panel in Cumberland mine is West-to-East while in Emerald mine, it is East-to-West. This unique condition required an adequate design for barrier pillar between the two mines to minimizing the mutual effects of longwall retreat when both longwall faces met and an adequate roof control plan for gateroads. Field studies that involved mainly roof-to-floor convergence monitoring were conducted to assess the effectiveness of the employed barrier pillar in isolating the mutual effect of longwall retreat. Three-dimensional finite element numerical modeling was used to evaluate the gateroad roof and pillar stability. The modeling was conducted such that it duplicated the actual mining process as realistically as possible. The modeling results predicted that the employed barrier pillar and the roof control plan would ensure stable gateroad systems in both mines during and after the two longwall faces met. The prediction was confirmed because mining operations in the two longwall panels were completed without any noticeable ground control problems.

Jan 1, 2004

By Clare Offner

In 1998, the Australian Coal Association Research Program (ACARP) awarded funding to the School of Mining Engineering at the University of New South Wales to establish a rockbolt testing facility to research anchorage mechanisms associated with fully encapsulated rock bolts and to develop standardised testing procedures for rockbolts. This facility is still under development but has already been used to evaluate the effect of bolt profile and confinement on the load transfer characteristics of a resin encapsulated rock bolt. This paper describes the test facility and presents some of the results of development testing to date.

Jan 1, 2000

By Axel Preusse

Stowing or waste fill is common in the German mining industry since the beginning of mining activities, With increasing mechanization, flat and gently inclined seams (0 -- 18) were mined. These mines were located within the densely populated areas close to important infrastructures such as industrial complexes, roads, highways, railroads, rivers and canals. These buildings and infra¬structures were rarely protected against subsidence influences and other ground movements and dump capacities close to the mines were exhausted. For subsidence reasons and because of the low dump capacities pneumatic stowing methods were continuously developed and used in German longwalls until 1997. Due to techni¬cal standards and because of some restrictions pneumatic stowing in Germany is only used at a minimum seam thickness of 2.00 m and average costs of this method are $20 - 30 per ton. A significant reduction of the disturbance potential and by that a decrease in expenses for subsidence regulations due to reduced subsidence and ground movements could not be achieved. In this paper the experiences with pneumatic stowing in the Ger¬man mining industry are described. Possible subsidence reduction and economic aspects of pneumatic stowing are taken into account.

Jan 1, 2002

By Craig Collins

The objective was to develop a Real Time Drilling Display System for Rotary Roof Bolting using Analyzing Software to display mapped holes as they are being drilled in real time. The Analyzing Software was developed to analyze and interpret drill sensor data produced during a rotary drilled roof bolt hole by using algorithms and drill sensor data trends to find and locate roof separations or voids. After this software was validated through lab and field testing, its application needed to be tested in a production environment. However, the current method used to record the drill sensor data proved to be cumbersome for the mine to use on a continuous production basis. With different more practical mediums being explored and considered, a Drilling Display System was developed that will both map holes in real time and record the data for later review. With the Analyzing Software's current level of accuracy and with the convenience offered by the real time Drilling Display, the Drill Display System was implemented along with a test mine's current roof control plan and tested as a roof separation "Early Warning System". After installing the Drilling Display System onto a machine, input and suggestions from the mine environment were considered and design changes were made. The real world application provided a design direction that made the information produced by the Analyzing Software both convenient and significant for the test mine. Also, using the Drilling Display System increased the number of drilled holes that were both mapped and recorded. The results from studying these recorded data files lead to refinements in the current algorithms used by the Analyzing Software which increased the overall accuracy and capability of the system A fairly accurate representation of void or separation locations in the mine roof can be determined fromsensor data recorded during production bolting cycle. The immediate feedback on the local roof condition that the Drilling Display System provides, amounts to a quicker and safer alternative to the scratch hole and the video bore-scope examinations that arc performed after the bolting is completed. This project has shown that making the alternative method of examining the roof condition practical for the mine to use is just as important as the accuracy of its results. Based on the results of this field test, this or other methods of reviewing the analyzed drill hole data will be explored.

Jan 1, 2004