Search Documents

By Karsten Zimmermann, Peter Cain

"To receive regulatory approval for a new coal mining operation in North America, extensive investigations of feasibility and potential environmental impacts, including ground deformations, are required. Figure 1 shows pictures from mine sites and an example mine map with the planned panel layout for one seam of the multi-seam longwall operation considered.The cumulative mined coal thickness of 22 meters in some areas of the operation requires a comprehensive forecast of expected ground movements and subsidence impacts (e.g., subsidence, slope, displacement, curvature and strain). In the frame of the impact study, the prediction of these impact factors was conducted by DMT using the computer program SPS 4D, based on the Ruhrkohle modeling method by Ehrhardt and Sauer (1961).This paper briefly presents the modeling method and explains the benefits and possibilities for its international application. Information gathered from literature studies on subsidence in North America were incorporated into the initial model parameterization. The article shows the ways in which the observed influences of mountainous topography on surface displacements and deformations can be considered by an extension of the subsidence prediction model and integration of DEM information.SUBSIDENCE MODELFor the calculation of mining-induced subsidence and deformation, DMT has developed subsidence prediction software SPS 4D, which is built according to the stochastic prediction model by (Ehrhardt and Sauer, 1961). The model is based on the subsidence theory by (Knothe, 1953) with a specific parametrization of the stochastic influence function and includes enhancements for dynamic subsidence calculations after (Sroka, 1978). In Europe, mainly in Germany and Poland, the model is approved by the authorities as a standard model for subsidence prediction in mining areas. However, extensive research within R&D activities has shown the possibility to predict mining-induced subsidence considering the specific mining conditions in North America (Zimmermann and Fritschen, 2007)."

Jan 1, 2016

By David Dye

Good morning, everyone, and thanks Syd for that fine introduction. I am honored to be here to help you celebrate 25 years of advancement and success in the important field of ground control. I would also like to recognize Dr. Peng for his significant contributions in longwall mining and ground control. His contributions have had a major impact on improving safety and reducing fatalities in America?s mines. Thank you, Dr. Peng, for the important work you have carried on throughout the years. Many miners are alive today because of your dedicated work to protect them.

Jan 1, 2007

By Christopher Mark

The Analysis of Retreat Mining Pillar Stability (ARMPS) program has been used to evaluate room and pillar retreat mining layouts since it was first released in the mid 1990s. After the Crandall Canyon mine disaster focused attention on the importance of pillar design, ARMPS became an essential component in most Roof Control Plans developed by mine operators. In 2010, NIOSH released ARMPS version 6, which features a ?pressure arch? loading model for deep cover room and pillar mining. NIOSH has also provided general guidance for using ARMPS, including design criteria based on statistical analyses of an extensive case history data base. Many real-world retreat mining scenarios entail mining configurations that ARMPS does not directly address. Some of these situations that the MSHA Roof Control Division (RCD) has encountered in the course of its reviews of more than 100 ?complex and non-typical? plans are ? Unmined pillars are left at the mouth of a retreat panel that function as a ?composite barrier pillar? ? The floor is extracted on retreat, increasing the mining height ? More than one row of bleeder pillars is left in an adjacent, previously mined panel ? A retreat panel is located above or below a gob area in a previously mined seam ? Bleeder pillars are partially extracted on retreat RCD has developed solutions that allow these situations to be fitted into the ARMPS framework, and these are presented in this paper. Also discussed are some of the rules of thumb that have been developed for various input parameters, such as the treatment of inseam rock and slab cuts into solid coal.

Jan 1, 2011

By B. Tulu, D. Gearhart

A comprehensive monitoring program was conducted to measure the rock mass displacements, support response, and stress changes at a longwall tailgate entry in West Virginia. Monitoring was initiated a few days after development of the gateroad entries and continued during passage of the longwall panels on both sides of the entry. Monitoring included overcore stress measurements of the initial stress within the rock mass, changes in cable bolt loading, standing support pressure, roof deformation, rib deformation, stress changes in the coal pillar, and changes in the full three-dimensional stress tensor within the rock mass at six locations around the monitoring site. During the passage of the first longwall, stress measurements in the rock and coal detected minor changes in loading, while minor changes were detected in roof deformation. As a result of the relatively favorable stress and geological conditions, the support systems did not experience severe loading or rock deformation until the second panel approached within 30–50 ft of the instrumented locations. After reaching the peak loading at about two to three inches of roof sag, the cable bolts started to unload, and the load was transferred to the standing supports. The standing support system was able to maintain an adequate opening inby the shields to provide ventilation to the first crosscut inby the face, as designed. The results were used to calibrate modeled cable bolt response to field data and to validate numerical modeling procedures that have been developed to evaluate entry support systems. It is concluded that the support system was more than adequate to control the roof of the tailgate up to the longwall face location. The monitoring results have provided valuable data for the development and validation of support design strategies for longwall tailgate entries.

Jan 1, 2017

By G. P. Neobutov

The near surface inclined gold ore deposit is mined out at freezing temperature. The replacement of ore pillars by artificial freezing rocks during the rock pressures control in this conditions presented no difficulties. At the present, the mining operations are maintained at a depth of more than 300 meters. The exploration of mining conditions showed partial warming of rock mass and unstable ground conditions. Analytical calculations using a mathematical model of heat exchange predicted undesirable duration of freezing of artificial pillars. Practical techniques and recommendations for mining with ice pillars as an artificial support system using a new freezing method are discussed.

Jan 1, 1996

By Nathaniel Schaefer, Christopher Newman, Zach Agioutantis

"As mining reserves continue to be developed in deeper and more complex geological and geometric conditions, there has been an increased demand for underground mine designs to better reflect site-specific conditions, measurements, and observations with respect to ground control safety and stability. Current ground control design software are limited to a given device and data files generated can only contain a single design. However, with the growth of cloud computing and increases in internet access, even underground where permissible, web-based software applications allow for in-the-field calculations, as well as collaborations, from multiple users. webGroundControl (webGC) utilizes a multiple-tier architecture, building upon existing NIOSH ground control design software, more specifically ARBS, ALPS, and ARMPS. By providing operators the ability to access ground control design programs from any device, given an internet connection, webGC allows for on demand calculations to ensure underground pillar and roof stabilities with respect to current site-specific parameters, geometries, and geology. Through the development of new features, which aid in design analyses, as well as project collaborations, webGC provides the modern engineer with a more versatile ground control design tool for the improvement of underground health and safety. With the completion of the ARBS, ALPS, and ARMPS modules, this paper introduces potential users within the mining industry to the navigation and operation of the webGC application, as well as its ability to facilitate collaborations between operational personnel and planning engineers. The purpose of this paper is to raise interest in the web-based application before its official launch in Summer 2018."

Jan 1, 2017

By Vincent A. Scovazzo

"The most significant study on the effects of longwall mining on gas and oil well integrity was completed by a consortium of coal and shale gas industry participants. A field study was conducted in 2013 and 2014 and is referred to by its location on Well Pad NV-35. The experiment site was located at the CONSOL Enlow Fork Mine in Washington County, Pennsylvania.The experiment was completed to verify John T. Boyd Company (BOYD) calculations and studies completed under contract by for the Pennsylvania Department of Environmental Protection Gas Well Pillar Study Update. The findings of the original study were presented by BOYD at the 32nd Conference, while numerical analysis of the Well Pad NV-35 field study was presented by Dr. Su at the 35th Conference.This paper addresses the findings of the experiment and how it confirmed the conclusions of the original study.INTRODUCTIONA field study was conducted in 2013 and 2014 by a consortium of coal and shale gas industry members to test the effects of longwall-induced ground movement on the stability and integrity of wells drilled through a gateroad abutment pillar. The project was initiated to test initial John T. Boyd Company (BOYD) findings of the Gas Well Pillar Study Update (Scovazzo and Moran, 2014), completed for Pennsylvania Department of Environmental Protection, Bureau of Oil and Gas Management (PDEP). Background and initial findings on this project were presented at the 32nd Conference (Scovazzo and Moran, 2012). The field work and numerical analysis were spearheaded by CONSOL Energy, Inc. (CONSOL) with participation by Chevron, EQT, Noble Energy, Range Resources, Marcellus Shale Coalition, and the Pennsylvania Coal Alliance.Dr. Wen H. Su of CONSOL was the leader of the field experiment with input from the participants. Dr. Su also completed numerical analysis of the results and model casing deformation. Analytical results were presented by Dr. Su at the 35th Conference (Su, 2017)."

Jan 1, 2018

By Josh Johnson, Stephen Tadolini, Mark Ferster, Curt Jacobs

"Stillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral. While driving two sub-parallel footwall laterals to about 8,125 m (26,000 ft) long, one of the development drifts experienced a massive fall in a geologically disturbed area created by a dike intrusion. Combinations of a void fill material (Tekseal), polyurethane injection, fore poling coupled with steel arches, and supplemental bolting allow safe and efficient advance through this geologically disturbed zone. This paper presents the details of this project.INTRODUCTIONStillwater Mining Company is the only U.S. producer of platinum group metals (PGMs) and the largest producer outside of South Africa and Russia. The Company controls a considerable portion of the J-M Reef and is currently developing the ""Blitz Project,"" which will provide a main haulage level, ore pass systems, backfill plants, and flow-through ventilation to increase production and ensure sustainable extraction of this critical strategic mineral.Tunnel Boring Machines (TBMs), shown in Figure 1, have been used extensively at both the Stillwater Mine and the East Boulder Mine to develop access to the J-M Reef. The J-M Reef is a PGMbearing reef deposit located in the Stillwater Complex near NyeMontana. The mining property and location are shown in Figure 2.The Blitz Project is named after the Blitz mining claims and is developing the Eastern extent of the J-M Reef Project., This consists of a 5.5 m (18 ft) diameter TBM drive on the SOE (1,562 m (5,000 ft) above sea level and east of the shaft collar) and a 4.7 x 4.7 m (15 x 15 ft) drill and blast heading on the 5,600E (1,750 m (5,600 ft) above sea level and east of the shaft collar). The Benbow Decline will be completed running perpendicular to the TBM by drilling and blasting methods. The TBM drift will be used for exploration drilling, ventilation, and will serve as the main haulage level. The 56E will be used for ventilation and exploration drilling. The Benbow decline will serve as the exhaust drift."

Jan 1, 2016

By Rob Thomas

"In Australia, a wide roadway is commonly defined as any roadway that is driven to a width greater than 5.5 m (18 ft). These roadways are typically required to enable the installation of longwall equipment (termed installation roads); however, other applications include the need to house conveyor driveheads and pre-driven recovery roads.As a result of the increasing size of longwall equipment and mine infrastructure, in some mines, roadway widths of between 9 and 12 m (30 and 39 ft) and are being developed.Accepting that these almost always constitute strategically important and often long-term roadways, this paper considers the use of: (i) an empirical roof support design model, which is based on over one hundred case histories, (ii) various roof support design principles, and (iii) commonly accepted strata management techniques.The paper demonstrates that wide roadways can be driven and supported to an acceptable standard providing due consideration is given to the prevailing ground conditions (including the quality of the immediate and upper roof strata, the Depth of Cover and the horizontal stressfield), the final width of the roadway and the required use of the roadway.INTRODUCTIONRoof behaviour and the associated roof support requirements in wide roadways, which are roadways typically driven to a width that is greater than 5.5 m (18 ft), are controlled by a number of key geotechnical and operational factors. The recognition of these factors is an important first step in the design process and it is imperative that each is considered in conjunction with local mine site information.The main points of note in this regard can be summarised as follows:• The greater the final width of the roadway, the greater the resulting surge in roof displacement on widening - note: a) see Figure 1 for a schematic illustration of the roof displacement trends typically measured during the development of the first pass and roadway widening, b) since displacement increases with roadway width, it is always recommended that the roadway width is kept to the minimum required and c) general buckling beam theory indicates that the capacity of any beams present in the roof will reduce in inverse proportion to any increase in roadway width squared (i.e., [final width2 -first pass width2] I final width2)."

Jan 1, 2010

By Chris Kelly

The Monroe County Quarry is an open pit granite quarry located near the town of Bolingbroke. Monroe County. Georgia. The quarry has been in continuous operation for approximately 10 years. The quarry covers approximately 27 acres and has an annual production rate of 1.0 million tons. On the morning of April 26. 2000 a sudden rapid highwall failure occurred at the west end of the north wall of the quarry pit. The failure occurred approximately one hour after a three inch-wide crack was observed in an access road located at the crest of the highwall. No indications of failure had been observed prior to the development of the crack. The active mining area had been at the base of the failed area. The pit was successfully evacuated prior to the failure and there were no losses of either personnel or equipment. The amount of failed material was estimated to be in excess of two million tons. In order to ensure a safe working environment at the quarry a slope monitoring program was established in the area of the failure. The program consisted of using an EDM survey instrument to periodically measure the location of survey prisms installed at carious points on the north wall. The locations of the prisms were recorded over several months and changes in location were analyzed in order to identify and characterize the movement of the failed mass. The results of the analysis provided a basis for recommendations regarding access to various areas of the quarry. This paper discusses the factors contributing to the failure, the method of post-failure slope monitoring, anti the interpretation of the monitoring data.

Jan 1, 2002

By Peng-Fei He

CT scanning tests were used to detect the pre-existing fracture systems of 36 cubical coal blocks. Systematic procedures were developed to construct the pre-existing fracture geometry of the cubical coal blocks from the CT images. Based on the constructed fracture systems, the fracture tensor components were calculated to capture the directional effects of the fracture system of the cubical coal blocks. The effect of the pre-existing fracture system and different combinations of confining stresses on the strength and deformability of coal masses was investigated at a preliminary level using some true triaxial test results and the computed fracture tensor components. The strength of the cubical coal blocks in the loading direction was found to be closely related to the summation of the fracture tensor components in the two perpendicular directions to the loading direction and the level of the confining stress system. The deformability of cubic coal blocks in the loading direction was found to be correlated to the fracture tensor component in the same direction.

Jan 1, 2014

By Robert B. Francini

Longwall mining and pipelines have coexisted since longwall mining was introduced into the United States. How the pipeline operator reacts to longwall mining under their line depends on many factors. This paper outlines the process the pipeline operator goes through to determine the appropriate response when their pipeline is being undermined. Typical mitigation procedures are reviewed. Finally, the paper looks at current design practices for new pipelines that are expected to be undermined during their lifetime.

Jan 1, 2011

By Denise Y. Dizon

The objectives of this study were to document the hydrologic impacts of longwall mining on streams, identify the factors affecting the extent of stream dewatering, and develop empirical trends to predict the extent of dewatering and recovery of streams in advance of mining. This study on stream impacts is a companion to a stud; conducted on ground water impacts from longwall mining, which was done as part of the same research project at the' same locations and times. The study areas are three mine sites in north- central West Virginia. Mine A, located in Upshur County, has relatively thin mine overburden under the valley streams (105-115 feet). Stream monitoring there continued the earlier work of Cifelli and Rauch (1). Stream dewatering was severe with streams often going dry over the longwall panels during baseflow conditions. The lost water was probably flowing to the mine. Dewatering began in streams over the mine entry areas adjacent to the panels and as much as 380 feet from the nearest panel edge. The angles of dewatering influence ranged 22 to 72 degrees with respect to the nearest mined panel edge. Discharge then typically increased as the streams- flowed across the panel edge, but then decreased again over the panels. These streams were often ponded by local reversals in hydraulic gradient caused by land subsidence, and often dried up after flowing a few hundred feet across the panels. This occurred over panels that were previously mined up to eight months before. Mine B, located in Monongalia County, has relatively thick mine overburden (475-485 - feet) under the major stream. Stream dewatering was severe there during warm season baseflows, with complete dewatering occurring then over the longwall panels. This dewatering occurred over mined panels up to five years old, probably in response to a major anticlinal axis lineament and fracture zone in the stream valley. Mine C. located on the West Virginia -Pennsylvania border, has relatively thick mine overburden (about 585-630 feet) under the monitored streams there. stream dewatering was only partial, and these streams typically recovered their lost discharge downstream of the mine, indicating that lost water was not recharging to the mine. Only longwall panels less than one year old were associated with stream dewatering.

Jan 1, 1990

By Essie Esterhuizen, Michael M. Murphy, Chris Mark

"The design of underground coal mines requires a clear understanding of the overburden response, the loading of pillars, the loading of the gob, the pillar failure process, and the ultimate load carried by partly or fully yielding pillars. Very few highquality stress measurements of yielding pillars and gob loading have been made in full extraction mining. Well-calibrated numerical models can assist in providing a better understanding of the load and failure processes, provided the coal, the overburden, and the gob are all modeled with sufficient realism. A program of numerical model calibration and validation was carried out using FLAC3D.1 The models were calibrated against observed and measured performance of coal pillars and the overburden in operating mines to provide a basic set of input parameters that can be used to provide a realistic first estimate of expected ground response and pillar loading. Input parameters for modeling coal pillar response were based on data from triaxial testing on coal samples, combined with both matching the depth of failure in the coal ribs to observations as well as matching the peak pillar resistance to an empirical equation. The models were calibrated against strong roof and floor case histories in which the pillar strength is governed by failure and yielding of the coal within the pillar and the surrounding strata only had a limited impact on pillar strength. Input parameters for the overburden were determined from a large database of laboratory tests and model calibration against maximum subsidence and subsidence curvature. Further overburden calibration was carried out by matching stresses in the mining horizon to field measurements. Three examples of the application of the calibrated dataset and modeling methodology to field measurements are presented. The results show that a reasopable estimate of the in-seam stress distribution and overburden response can be obtained for both strong and weak overburden scenarios at various depths of cover.INTRODUCTIONThe planning and design of coal mine excavations requires reliable estimates of the expected strength and loading of the mine structures to achieve global stability. Empirical methods are widely used to estimate the strength and loading of coal pillars and have been incorporated into pillar design procedures, such as Analysis of Longwall Pillar Stability (ALPS) (Mark, 1987) and Analysis of Retreat Mining Pillar Stability (ARMPS) (Mark and Chase, 1997), that are widely used in the United States. ~umerical models are finding increasing application as a tool for underground mine design because of their. versatility and the ever increasing computational power available to mine designers. A prerequisite for the application of numerical models is the calibration of the models against observed rock mass response (Hoek et al., 1990; Skiles and Stricklin, 2009). The calibration process may include comparison of model results to measured stress and deformation and modifying the input parameters in a systematic manner to achieve a satisfactory agreement between the model results and measurements. Once models have been calibrated, they can be applied to evaluating similar mining layouts in similar geological conditions."

Jan 1, 2010

By R. F. Valene

This paper is not available for inclusion in the Proceedings at the time of printing. but it will be included as an insert

Jan 1, 1984

By Wojciech Masny, Andrzej Walentek

"The most common extraction method in Polish coal mines utilize pillars between adjacent longwall panels. This is mainly due to the significant depth and difficulties in maintaining stability of the gateroads. This paper presents measurements of entry convergence and range of the fracture zone around a gateroad measured with a borehole camera. The entry where the measurements were taken was located in a parallel entry separated from the gateroad by a 5-m- (16-ft-) wide pillar. The gateroad was located in a hard coal seam 900 m (2,952 ft) deep with a dip of 5°. The extraction method was longwall mining with caving and the mining height was about 3 m (10 ft).Furthermore, the ""in situ"" measurements were compared to the convergence forecast for the gateroad and fracture zone by means of numerical modeling conducted using the Phase2 Version X.X finite element program from Rocscience. The determination of the fractured zone around the openings is of great importance to successful mining practice, especially in support planning and design for longwall gateroads. Moreover, proper determination of the fractured rock zone is one of the basic elements in the process of planning the roof bolting for mine workings.INTRODUCTIONIn the Polish. hard coal mining sector, retreat longwall extraction is most commonly used (Prusek and Masny, 2007). This method is connected with the necessity to carry out a number of development operations during the first stage, including among others, driving of gateroads and a setup room.Currently, most Polish mines eliminate gateroads behind the extraction front, using the ""U"" ventilation system (Szlitzak et al., 2008). In such cases, one of the roads for the next longwall panel is driven along the caving goafs, leaving a protective pillar of some chosen width (Figure 1). The question regarding the width of the coal pillar is especially important to the stability of the gateroads that define the panel for the subsequent longwall. When analyzing the previous experience relating to this type of pillar (Junker, 2006; Rajwa, 2008; Stranzet et al., 1973; Betriebsempfehlung, 1982), one can state that there exist two solutions for the determination of its width."

Jan 1, 2010

By Bowler Jonathan, Lorraine Kent, Tereza Crisu, Stuart Walker, Nicholas Lightfoot

"It has been the practice in Europe to extract the most economic seams first: taking the seams sequentially, top down, to avoid operating within the fractured strata formed by the subsidence trough above previously mined coal seams. In the 1990s, the UK coal industry found itself at a number of sites having to operate over one or more previously mined seams. This led to specific geotechnical challenges with respect to maintaining economic, safe and stable rectangular roadways with rock-bolted support.Within this paper, the current challenges and mitigation strategies of overmining in the UK are described following the completion of a -three-year European Commission-funded project in 2015. The challenges and mitigation strategies are related to:• A case study with overmining of older workings of variable geometry;• Numerical modeling for overmining layout and support design; and• A case study site planning mine layout when considering future overmining.INTRODUCTIONAt the first case study site, case histories were examined for a mine operating at a depth of approximately 700 meters where five longwall panels were extracted above workings 35-40 m below. The overmining of various extraction geometries below led to challenging conditions in areas of high vertical stress concentration. It was found that results from one longwall panel could be suitably used to predict behaviour in a subsequent panel. The experience was used to update previously existing guidelines on the positioning of roadways in relation to subsidence troughs. Existing guidelines recommended that only as a last resort should longwalls be planned to retreat over narrow pillars, or from solid ground into a subsidence trough. Existing guidelines regarding the layout of overmining panels are conservative, and new work indicates that such multi-seam geometries are possible with appropriate support management strategies."

Jan 1, 2016

By Keith A. Heasley, Christopher R. Newman

"Originally developed in 1993, LaModel has aided mining engineers and researchers alike in improving the design and safety of underground single- and multiple-seam mining operations (Heasley, 1998). Through the years (Heasley, 2011), the use and capabilities of the LaModel program have grown immensely while adapting to ground control concerns and problems within the mining industry. Presently, MSHA specifically mentions the use of LaModel for the analysis of, “complex non-typical roof control plans,” defined as either room-and-pillar retreat mining greater than 1000 feet, bump- or bounce-prone mines, or other criteria considered unusual by the District Manager (Stricklin, 2013).With an ever increasing number of users and an increase in available solution options and complex analyses, there is now a significant demand for better education and training in the practical application and detailed analysis using LaModel. This paper presents the development of an electronic user’s manual and comprehensive online training course created in an open online learning environment in order to better inform and train industry professionals as well as engineering students and new users. The development of both the user’s manual and online training course will ultimately increase the ground control design effectiveness of mining engineers, leading to safer and more productive mine designs.INTRODUCTIONOver the past 20 years, mining engineers and researchers have used the LaModel program for improving the design and safety of single- and multiple-seam mining operations. LaModel uses a laminated, displacement-discontinuity, boundary-element method which simplifies the overburden into a stack of frictionless homogeneous laminations and limits the detailed analysis to the seam itself. This approach is fundamentally simpler than either finite-element, finite-difference, or discrete-element approaches; and, therefore, the program provides a significant reduction in computational time and efficiently calculates the displacements, stresses, pillar safety factors, multiple-seam interactions, subsidence, etc. for thin-bedded deposits such as coal, salt, potash, limestone, etc. (Heasley and Salamon, 1996; Heasley and Agioutantis, 2001). The laminated overburden model in LaModel is different than previous homogeneous elastic formulations and more realistically represents the natural flexibilities of the stratified sedimentary overburden typically associated with coal seams (Heasley, 2008)."

Jan 1, 2015

By C. D. Peters

The Bureau of Mines has been researching remote sensing analysis of an underground coal mining area in Utah and computer-aided methods of defining ground control hazards in this mining area. As a result of these studies, a preliminary potential hazards map was developed for the test site. This map is based primarily upon a lineament (linear feature) analysis of Landsat satellite data. Other data used were paleochannel location data, resistivity data, and information from surface and underground field checking of the lineaments and ground control problems in the mine. Lineaments proved to be reliable indicators of hazardous areas, although the type and degree of hazard varies with different lineament trends and the presence of other conditions such as lineament intersections and intersections with other geologic structures or with paleochannels. Lineaments were observed to match faults, joints, and/or joint trends in the area. The paleochannel data, derived from drill hole data, provided basic information about potentially hazardous areas in the mine by suggesting where paleochannels could cause instability in the roof rock. The ground control problem data served largely to define the relative degree of hazard associated with lineaments and the types of hazards encountered in the mine. Resistivity data helped confirm the presence of fractures where they were expected to occur both from surface geology and from the lineament data.

Jan 1, 1986

By Sahendra Ram, Arnn Kr Singh, Dheeraj Kumar, Rajendra Singh

"Inherent existence of different rooms (openings) along the extraction line in a depillaring panel provides an easy path for the goaf to encroach the working area. Each of these openings in a mechanized depillaring (MD) operation along the extraction line is supported by the roof bolt-based breaker line support (RBBLS) to restrict the goaf encroachment. Different field studies by Council for Scientific and Industrial Research - Central Institute of Mining and Fuel Research (CSIR-CIMFR) found that the RBBLS works effectively during the depillaring under the shadow of stable surrounding ribs/fenders only. It is observed that, generally, these natural supports experience high value of induced stresses after a large amount of void creation inside the goaf. The induced stress creates spalling/loosening of the sides of the natural supports. Field studies also found that the positions of the RBBLS at the goaf edge need to be adjusted according to the depth of this spalling/ loosening. However, a systematic study in field for the correct positioning of the breaker line as per the spalling/loosening under different site conditions is difficult. Therefore, on the basis of the data and guidance provided by these field investigations, a detailed parametric investigation was conducted in the laboratory on simulated models for an effective design of RBBLS in a MD panel. FLAC3D is used for the simulation of the depillaring, and the available empirical formulations for Indian coalfields are used for subsequent calibration. An analysis of stress redistribution for different stages of the MD in simulated models showed the significance of the nature of overlying strata/induced stress for the RBBLS design. Discussing some results of field studies, this paper presents results of the laboratory investigations for an effective design of the RBBLS.INTRODUCTIONContinuous Miner (CM)-based mechanized depillaring (MD) is an important issue for Indian coalfields, where huge amounts of coal are locked up in standing pillars (Dixit and Mishra, 2010). Considerable variations in site conditions of these developed pillars bring a number of technical challenges into consideration during their final extraction. One of these challenges is goaf encroachment/overriding during caving of the competent roof strata. Goaf encroachment/overriding can effectively be controlled, mainly, by suitable design of natural supports (rib/snook/fender). However, there is a requirement of applied supports against the immediate roof as a considerable portion of this roof is exposed due to the presence of different openings along the line of extraction. These applied supports act as a fulcrum at the goaf edge between the working area and the goaf to facilitate the break out of the hanging roof inside the goaf. This is called breaker line support. An effective breaker line support is important for the efficiency of a depillaring operation. Generally, MD adopts roof bolt-based breaker line support (RBBLS) at the goaf edge (Singh, et al., 2014). For the first time in India, roof bolts were applied at the goaf edge as RBBLS in a CM-based MD (Leeming, 2003). In the beginning, three rows of roof bolts were installed as primary and secondary breaker lines support. On the basis of the observations of instrumented bolts, only two rows of roof bolts were used as secondary RBBLS (Ram, et al., 2014). Now, most of the MD operations in India are using only two rows of bolts as RBBLS (Table 1). However, the strata mechanics studies at different MD operations showed interesting characteristics resulting from this support (Ram, et al., 2015)."

Jan 1, 2016