Search Documents

By M. G. Premo

The McKinley Mine is located in the northwest New Mexico, in McKinley County, approximately 25 miles from Gallup. The mine is operated by The Pittsburg & Midway Coal Mining Co. (P&M), a wholly owned subsidiary of the Chevron Corporation. P&M is headquartered in Englewood, Colorado. Since the McKinley Mine began operations in 1962 a total of 83,391,000 metric tons of coal have been sold through 1990. The 1991 production was approximately 5.000.000 metric tons. The mine operations are contained on a 109.000 square kilometers lease area of which 44.000 square kilometers are on the Navajo Nation. The present customer base consists of four utilities and one industrial account, all of which are located in Arizona. The utility customers are the Arizona Public Service Co. Cholla Station at Joseph City, The Salt River Project. Coronado Generating Station near Joseph City, and The Tucson Electric Company, Irvington Generating Station in Tucson. The industrial customer is the Stone Container Corporation, Snowflake Paper Mill.

Jan 1, 1992

By E. Kurt

The field of percussion rock drilling is subdivided into two areas of application; that which takes place on the surface and that which takes place underground. Surface drills are used in quarrying, highway construction, and maintenance work; underground equipment in mining and tunneling work. Two basic principles are involved in the operation of all percussion drills. First, the principle that reciprocates the impacting piston and second, the principle that causes the drill steel and bit to rotate. The back and forth motion of the piston is accomplished by a self-acting automatic valve that admits air alternately to each end of the piston (Figure 1). Drill steel and bit rotation is imparted by an integral ratchet mechanism (Figure 2) in the so-called "rifle bar" machines (Figure 1) or by a separate pneumatic motor in "independent rotation" drills (Figure 3). While rock drills are subject to all kinds of physical and operational abuse, they are most sensitive to faulty lubrication. Proper lubrication is the single most important factor in the longevity of a percussion drill.

Jan 1, 1970

By H. G. Fleshman

?Wyoming bentonite? has become almost a world-wide trade mark for high quality sodium bentonite. Although bentonite is produced in more than a dozen U.S. states the largest producing area covers Wyoming and adjacent parts of Montana and South Dakota. Bentonite was originally known as Taylorite and later renamed Bentonite by Dr. Sam Knight, the State Geologist of Wyoming. The new name came from the Fort Benton shale member of the Mowry Formation. Bentonite is a clay consisting essentially of the montmorillonite group of minerals. Since bentonite has good ion exchange capabilities, various cat-ions are easily replaced. These cations are usually calcium and sodium; however, magnesium, lithium, potassium, and others can be exchanged. One way of classifying the clay is based on its swelling capacities when wet or added to water. Bentonite having sodium as the dominant exchangeable ion typically has very high swelling capacities and forms gel-like masses when added to water. Bentonite in which exchangeable calcium is more abundant than other ions has much lower swelling properties than sodium varieties.

Jan 1, 1987

By Raymond E. Connell

From a macro business process perspective, if what we do in the Mining Industry is find material, dig it out of the ground, convert it to a product and sell it, we are in what might be considered a "simple business". If it is so simple, where does information technology fit? How does it affect our industry? Is it a strategic tool for our industry? What approach should we be employing to ensure we are utilizing information technology effectively? How is information technology integrated or tied together with other areas in the organization such as process control? What kind of people and skill sets are required to support the whole area of information technology? What effect does information technology and automation have on streamlining and rethinking the way we do business in the 90's. This paper covers how these areas have been addressed within the Noranda Group of Companies. It reviews how information technology has evolved, the approach, and what effect it has had on a diversified natural resources company in the mining and metals, forest products, and oil and gas industries.

Jan 1, 1993

By E. R. Hendrickson

About 1/3 of the world's supply of phosphate rock is produced in a relatively small area of the Florida peninsula east of Tampa. Until this past year, a circle with a radius of about 25 miles and centered on Bartow would encompass the major producing areas. During the past year producing areas have opened in North Florida which promise to vie with the Polk-Hillsborough County area in terms of proven reserves. In addition, new phosphate production is planned for counties to the south and west of the present fields. From the existing production areas, however, more than 19 million long tons of phosphate were mined in 1965. As mining engineers most of you probably are familiar with the methods of mining and beneficiating the pebble phosphate rock. You thus recognize that, although some water quality problems may arise from these processes, there is no potential air pollution problem. To make an economically useful product, however, further processing must take place. It is from this additional processing that potentially damaging materials may be discharged to the atmosphere.

Jan 1, 1966

By R. R. Godard

The practice of dust abatement or control is not new to any operation of United States Steel Corporation. This report will review those activities, past and present, within the five operating districts of United States Steel-Coal Operations with specific reference to mechanical and continuous mining, and including both the health and safety aspects of the problem. Obviously, the first principle of dust control is to inhibit its formation If this is not practical, steps may be taken to prevent its becoming airborne. Airborne dust control can be realized by either collecting it at the point of generation, diluting it with large volumes of air to reduce concentration, settling it by various means, or with reference to ignition hazard only, render it incombustible by neutralization with an inert material. These basic principles have been verified by the work of many, including the Bureau of Mines, U. S. Department of Interior, Bituminous Coal Research, Inc., and the Mining Research Establishment of the National Coal Board of Great Britain. Their application to every day mining problems is best illustrated by the following examples.

Jan 1, 1967

By A. K. Mukhopadhyay, B. Sikdar, V. P. Arora

Introduction During the past several years, persistent concerns about an economic slowdown in India have tempered capital-expan¬sion plans. This has encouraged companies to find methods of increasing the capacity of existing production equipment. One of the more cost-effective methods of increasing produc¬tion capacity without major capital investment is to improve equipment maintenance to prevent needless machine down¬time. This can have a significant financial impact because of reduced maintenance costs and increased machine availabil¬ity. The maintenance program employs different techniques, but the analysis of the vibration behavior of machine compo¬nents to assess their condition was found to be the most accurate technique for monitoring various machine disorders. A dragline that handles overburden in open pit mines is one of the more capital-intensive pieces of production equip¬ment. It is imperative that the machine be run at its optimum capacity under the prevailing environmental conditions. Condition monitoring of the various components of the dragline through vibration analysis not only improves the machines availability but also ensures a long operation time free from sudden failure. This paper describes the application of vibration monitor¬ing and analysis techniques to assess the components of a W2000 dragline. The paper reveals that condition monitoring through vibration analysis can be as valuable in failure prevention as it is in failure analysis. Finally, the paper presents an approach to a knowledge-based expert system to the quick and correct diagnosis of mechanical faults in a dragline. Equipment A dragline is an intermittent-discharge-type excavator having a long boom at one end. Unlike other excavators, the bucket is not rigidly held by the frame structure. In favorable geomining conditions, the intensive operation of these exca¬vators is the least-expensive means of overburden removal. The basic working elements of this equipment are the hoist system, the crowd and retract system, the wing mechanism and the propel mechanism. The walking dragline is accepted as the most economical machine for stripping overburden at depths of up to 60 m (200 ft). They are electrically powered and the various motions are effected by individual drives. The Ward-Leonard system is used to provide the optimum flexibility in controlling different dc-drive motors. To mini¬mize the cost of mineral extraction, the largest such machine in India has a 24-m3 (850-cu ft) bucket with a boom length of 96 m (315 ft). Draglines are very costly, and considerable financial penal¬ties may arise from sudden stoppages due to component fail¬ures. Thus, operational reliability is of the greatest importance. Active measures are now being taken to minimize downtime by adopting condition-based maintenance techniques. Though a number of techniques come under this scheme, it has been observed that assessing the health of the dragline by measuring vibration is the best method of determining the dynamic behavior of its various rotating components to avoid any catastrophic failure. Based on criticality, the vibration-behav¬ior of the following components are studied: • motor-generator unit, • exciter unit, • hoist motor-gearbox unit, • hoist drum-gearbox unit, • drag motor-gearbox unit, • drag drum-gearbox unit and • swing motor unit The approach Increases in the vibration levels in different subsystems of the dragline were observed due to the presence of faults such as unbalance, misalignment, looseness and bad bearings. A vibration behavior study included the measurement of vibra¬tion level, trend analysis of time-domain vibration signals and vibration frequency analysis at bearing points of the components. A vibration meter, a vibration analyzer and a data collector are used. Vibration-level measurement. When the dragline was assembled and put into operation for the first time, vibration data were collected to generate baseline data for the equip¬ment (based on International Standard ISO 2372). After¬wards, the vibration levels were recorded regularly using a vibration meter. The measurements were taken at all bearing

Jan 1, 2000

By Edmond Donovan, O&apos

With the increase in complexity of conveyor systems and the inexorable demand for more capacity and availability, the ability of designers to accurately predict performance is becoming increasingly important. Dynamic analysis techniques for modelling wave mechanics in conveyors are finding increased applications. Unfortunately, the reliability of these modelling techniques is dependent on a thorough understanding of the performance characteristics of the components that make up the system. These characteristics include such things as response rate, hysteresis and efficiency. Some parameters such as idler rolling resistance can be easily quantified by measurement. More complicated drive parameters are difficult or impossible to measure, particularly in large horse-power equipment. One method of quantifying or at least bracketing the performance envelope of complicated pieces of equipment is to construct a mathematical model. This can be done quickly and economically, and the influence of various parameters can be determined. This paper sets out to demonstrate by example the usefulness of this technique in gaining an understanding of complicated systems. The model is developed and the influence of a number of variables are examined.

Jan 1, 1996

By M. H. Basiri

Crude oil, as a central commercial commodity, is tied to major economic activities in all nations. Also its price fluctuation plays a significant role in global political and economic situation, as a change in the price invariably affects the cost of other goods and services. Therefore reliable forecasts of the price of oil are interest for a wide range of applications. Several approaches have been proposed over the past few years. These may divide into three categories; artificial intelligent, statistical techniques and hybrid methods. The neuro-fuzzy is one of the sub divisions of hybrid method, containing neural network and fuzzy techniques. In this paper a novel forecasting model based on adaptive neuro-fuzzy inference (ANFIS) is proposed to predict monthly crude oil price. To be able to train and test the model, the statistical data from 1990 to 2010, was obtained from West Texas Intermediate oil prices. The results are compared with a multi criteria regression analysis, it is demonstrated that the neuro-fuzzy lead an accurate and more promising forecast.

Jan 1, 2012

By J G. Dunn, S M. Thurgate, A C. Chamberlain, P Franzmann, M Jeffrey, L J. Warren, G E. Poinen, T Williams

Gold has always fascinated mankind. From Tutankhamen's mask to the huge nuggets that have been found in the Australian outback, gold has quickened the pulse and fevered the eye. But in recent years, governments around the western world have shown a singular lack of interest in research into gold processing, with many programs being cut. There are some notable exceptions, fortunately, and this paper summarizes a large research effort that is well supported by the Australian government and the Australian gold industry. The AJ Parker Cooperative Research Centre for Hydrometallurgy is an unincorporated joint venture between the CSIRO Division of Minerals, Murdoch University, Curtin University of Technology and the Western Australian Department of Minerals and Energy. The Australian Mineral Industry Research Association (AMIRA) is the Parker Centre's broker for generic R&D contracts with industry. Each of the partners makes available staff, students and equipment to further the work of the Parker Centre, and the Australian Government provides additional funding. The Parker Centre is nearly five years old and has grown spectacularly in that time. There are now about 30 full-time-equivalents of effort from 50 scientists and engineers, as well as about 40 postgraduate and honours students. The fundamentals of the key operations in hydrometallurgy are studied in three programs: leaching (which includes pretreatment by roasting etc), precipitation (or crystallisation), and surface processes (which includes solid/liquid separation, adsorption, solvent extraction, etc). A large part of the Parker Centre's R&D is directed towards gold processing technology. In Australia, a dramatic increase in gold production, from about 30 to nearly 300 tonnes per year (1977-1997), has been made possible largely as a result of a brilliant metallurgical innovation, the carbon-in-pulp process. However, falling head grades eg 2.56 to 1.84 g(Au)/t over the last 10 years, and environmental concerns, are squeezing profit margins. There is increasing pressure to reduce costs, and the Parker Centre program is focussed on providing the scientific understanding required to do this. A selection of research highlights will be given, to indicate the depth and breadth of the R&D at the Parker Centre.

Jan 1, 1997

By James R. Walsh

While flue gas scrubbing with alkaline solutions is one of the oldest methods of removing SO2 from flue gas, a satisfactory scrubbing system for this application, which is both technically and economically viable, has yet to be developed. Interest in alkaline scrubbing has continued because of its basic simplicity and comparatively low capital cost. Drawbacks of alkaline scrubbing are the tendency for accumulation of solids to plug the system, scaling, corrosion and erosion problems and the need to dispose of large quantities of waste. Discussed are instrumentation loop applications to a 90,000 cfm alkali scrubbing test facility, the process problems the instrumentation engineer faces in. selection of equipment, the performance of the instruments selected and the problems encountered during start-up. The Test Facility incorporates centralized electronic process control with a digital data acquisition system provided to log process variables and print off normal (alarm) conditions. Flue gas SO2 content is measured by ultra-violet analyzers and analysis of the total gas stream is by gas chromatographs.

Jan 1, 1973

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

INTRODUCTION The majority of ground water flow models have been developed for large computer systems. Most of these operate under a batch mode of operation, that is, the data are input with a deck of punched cards. The advent of micro- and minicomputers over the last few years opens the possibility of adapting many of these large flow programs to the smaller computers. In general, this adaptation will require more computer time to run the program, but in many cases if the small computer is in-house, the overall cost may be less than that required for a large computer. There are also a number of peripheral devices that can be used to make the data input much easier. As an example, the use of a digitizer with a finite element or finite difference mesh reduces the data input time considerably; the use of a graphics terminal for display of the mesh immediately after it is developed shows immediately whether there are errors in the location of node points. DEVELOPMENT OF AN INTERACTIVE SYSTEM The finite element program, UNSAT2, has been used over the past several years by the authors for several ground water flow problems (Bloomsburg, 1977; Bloomsburg and Wells, 1978; Zahl and Bloomsburg, 1980). In the past these programs have been run on an IBM 370/ 145 computer under the batch mode of operation. One difficulty that has been encountered has been in determining the length of time step that must be specified for operation of the program. The problem is that if the time steps are too large, the program becomes un- stable and operation ceases. If this happens in the middle of the problem, the only alternative is to reduce the length of time step and repeat the entire run. This problem has been alleviated in other pro- grams by using a subroutine that determines the time step automatically. If the solution becomes unstable, the time step is reduced automatically and that portion of the solution is repeated. With an interactive system this can be done by storing the output pressures and restarting the program with the new output pressures. Under the batch mode of operation, there is an option in UNSAT2 that allows restarting of the program from the last point of solution, but this must be specified when originally starting the program. The interactive computer system that we use currently consists of a PDP 1 1 /23 with hard disk drive, CRT terminal, plotter, graphics terminal, digitizer, and printer. The computer has 256 K bytes of core storage and the hard disk drive will accept a 5.2 M byte disk. To run a large program on a computer such as this, some overlaying must occur; that is, subroutines are stored on disk and put into core storage only when they are actually needed for running the program. UNSAT2 required very few changes to run on this computer but some changes were necessary to take advantage of the interactive capabilities of the system. One of these changes consists of the development of a program called DBUILD to build the data file for running the program. This program calls for each piece of data by prompt statement and gives instructions for using the digitizer. The data are then entered in completely unformated form. The node points must be entered in order and the coordinates are determined automatically by the digitizer. The pressure readings or initial conditions on each node point are entered through the terminal. All element information also is entered through the terminal. After DBUILD is run the mesh may be displayed immediately on the graphics scope whereupon any error in node point

Jan 1, 1986

By R. Ciccu

Permeable reactive barriers (PRB) are one of the most promising systems for groundwater remediation. PRB are constructed with the purpose to intercept the contaminated flow and to degrade it as a big reactive filter. The most common type of reactive barriers is realized by excavating a trench and by filling it with a substance able to treat the contaminants dissolved in the water. Another type of PRB is obtained by realizing a line of wells in which chemically active compounds are injected. A new method for barrier construction has been studied at DIGITA?s laboratories. It makes use of the waterjet technology to increase soil permeability and to inject active compounds. This technology is especially suitable in the case of deep contaminated aquifers where traditional construction methods are difficult to apply. The paper describes the experimental apparatus especially designed and constructed and the activities carried out to investigate the relationship between waterjet operative parameters and the penetration of the jet in the soil. In conclusion, on the basis of the experimental results, the economical feasibility of the technique is evaluated.

Jan 1, 2008

By H. Sevim

In long-term open pit production planning, a series of nested and maximum-value pits is usually generated first. These pits are then considered as possible pushbacks over a number of planning periods. To determine the best pushback in each planning period, the pits are evaluated for their technical and economical feasibilities under certain production constraints. Parameterization is a commonly used technique to generate a series of pits. In almost all cases, however, some of the consecutive pits generated by this technique are too far apart from each other. This is called the "gap" problem. It may make the entire pit series useless for production planning purposes. A new pit gener¬ating algorithm has been developed to overcome the gap problem. Through this algorithm, a series of nested maxi¬mum-value pits can be generated with a controllable size increment. The logic of the algorithm is illustrated through a small hypothetical case. Its capability of generating maximum-value pits that are as optimal as those generated by parameterization and its advantages over parameteriza¬tion are presented through an actual gold deposit case.

Jan 1, 1996

By N. L. Wesis

General History The first jaw crusher in the US was patented about 1830, but the Blake crusher that has maintained a substantial advantage over other types was invented in 1858 by Eli Whitney Blake. For going on 150 years the jaw crusher has been an invaluable machine; even today, when gyratory crushers have assumed most of the burden of crushing large tonnages of large rock and ore, the jaw crusher has a firm place in the mining industry. It is interesting that soon after the invention of the Philetius Gates gyratory crusher in 1881, a contest between the first No. 2 Gates and Blake jaw crushers of equal gape showed the gyratory to be 3.2 times as fast. This foretold a day not far in the future when the jaw crusher would not be adequate on the largest jobs. In his Textbook of Ore Dressing (1909) R. H. Richards recom¬mended that the word breaker be used for all machines breaking to relatively large sizes (say to 5 in. or greater), and crusher be used for finer work. Even in the 1968 US Bureau of Mines dictionary of mining terms the work breaker is defined by Richards in this context. However, in modern US usage it is nearly limited to coal breaking. Over the years the jaw crusher has been developed in a variety of forms but it appears today in these three general forms: (I) Blake type, (2) Dodge type, and (3) single toggle (or overhead eccentric) type. All of these crushers have a fixed jaw and a moving jaw, between which the coarse rock fragments are intermittently caught and crushed. The three types are differentiated by the manner in which the movable jaw is moved in relation to the fixed. Types The Blake-type crusher is shown in cross section in Fig. 1. The simplicity and strength that have made it first among jaw crushers are evident. The movable jaw is suspended from a cross-shaft at its upper end, this shaft being carried in bearings on the sides of the frame. The actuating mechanism consists of an eccentric shaft, also supported in frame-mounted bearings, which imparts through a pit¬ man and a pair of toggles a reciprocating motion to the bottom of the swing jaw, the return movement being effected by several spring¬loaded rods. The whole is built into a box frame with the crushing chamber at one end. As in all jaw crushers, the eccentric shaft is equipped with a heavy flywheel that maintains an even speed through¬out each stroke. The Dodge-type crusher illustrated in Fig. 2 is simple, mechani¬cally. Its movable jaw, being pivoted below the discharge opening, has minimum movement at crusher discharge and maximum at crusher feed. Because the choke point coincides with the point of least motion, these crushers are of relatively low capacity, and the rapid action in the feed area gives the machine the advantages of large reduction ratio and closely sized product. Thus, it fits well into low-capacity operations like sample reduction. Besides low capacity, its principal disadvantages are tendency to pack and make fines. The single-toggle or overhead-eccentric type of jaw crusher (see Fig. 3) has gained in usage, starting as a modification of the Dodge idea in that the greatest movement of the movable jaw occurs at the top, and being gradually improved and strengthened to its position today where it covers just as wide a field of application as the Blake type from the standpoint of feed opening. The motion of the movable jaw is the result of the circular motion of the eccentric shaft at the top of the swing jaw combined with the rocking action imparted to the bottom by the inclined toggle plate. Because of light weight and mechanical simplicity, it is economical in small mills and portable plants where the rock is not as tough and abrasive as to punish the machine with excessive impact from shocks, or excessive wear result¬ing from the pronounced vertical component of motion.

Jan 1, 1985

By Selamet G. Ercelebi, Mahmut Yavuz

An inherent aspect of longwall mining is moving the equipment from a mined-out panel to a newly developed panel. Moving times may be reduced by detailed preplanning. A very useful tool for planning is MS Project. Using MS Project, one can efficiently plan, manage and coordinate a project from conception to conclusion. The critical path analysis identifies potential critical activities which may cause excessive time delays. Changes to the tasks on the critical path can have significant impact 0.n the completion of a project. Assigning additional resources to these tasks (either moving labor from other tasks to critical tasks or providing labor overtime work) may reduce the move time. Simultaneous activities are the candidates for moving the labor from an activity to another. Each time a change is made, the critical path should be recalculated. MS Project quickly recalculates schedules and lets you see how changes in one part of the project will affect the overall plan. In this fashion it is possible to minimize the longwall move time.

Jan 1, 2002

By Q. Lin, D. Z. Wang

Molecular design plays an important role in development of new flotation reagents. Group electronegativity calculation is a main method of molecular design. It is commonly used in calculating the hydrophilic-hydrophobic balance of reagents, particularly in designing chain length of flotation reagents for located minerals. But there is a limit to group electronegativity method. The method can only apply to those of [Ø]known straight-chain compounds ([Ø] is the hydrophobic energy of each -CH2- , determined by experiment). In this Paper, we propose another new calculation method: fragment method of flotation reagent. The method could be used as a supplement of group electronegativity method to design and calculate flotation reagents without any limitation. With the fragment method, we can calculate the hydrophilic-hydrophobic performance of any known or unknown reagents including those complicate structure compounds such as cyclic, branch, heterocyclic and so on by summing the appropriate structural elements (fragment). The principle, calculation stages and some results of designing new-type flotation reagents by fragment method are presented in this paper.

Jan 1, 1995

In the early days of minimal environmental protection awareness and unreasoning economy development pressures, little attention was paid to growing environmental concerns in Fuxin colliery, especially the air pollution problem due to the long term mining activities. In order to determine air quality concentration levels, a new technique for synthetic assessment of ambient air quality by using the extension of matter-element method is proposed in this paper. The air pollutants data such as Sulphur Dioxide (SO2), Carbon Monoxide (CO), Nitrogen Oxides (NOx), Total Suspended Particulates (TSP), Particulate Matter (PM10), and dustfall collected at four different air quality monitoring stations located in four districts of Fuxin colliery is used. The results obtained indicate that TSP, PM10, dustfall and SO2 are the predominant pollutants. Other pollutants such as CO and NOx are also detected in Fuxin colliery. The air pollution comes mainly from industrial emissions, mining activities and the abandoned gangue stockpiles. Compared to those applied to other mathematical assessment methods, it is demonstrated that the extension of matter-element model is quite appropriate for air quality assessment.

Jan 1, 2006

By M. R. Wormald

A real time data acquisition system has been developed for implementing standard radiometric analytical techniques, applied to the monitoring and control of mineral processing plants. The system uses standard ECB-bus microprocessors and peripherals, in conjunction with a specially designed nucleonic pulse ADC. It is being applied to the accurate on-line analysis of naturally-,occurring radioelements in processing plants, for example by simultaneously measuring the intensity of 1.46 MeV gamma-rays from the naturally-occurring radioisotope K-40, and the stream density by gamma-ray transmission of 662 keV gamma-rays. Gain stabilisation of the NaI(T1) scintillation detectors is maintained by the microprocessor in slave units, each of which may control up to four sample presentation systems. Data analysis - including corrections for bulk density, radioactive decay of the Cs-137 gamma-ray source, pulse pile-up, dead time and external background - is carried out in a master computer which is connected to the slave unit, and can be interfaced to the plant control computer via data links.

Jan 1, 1986

By J. D. Forrester

In striving to develop this discussion about "Manpower for Industrial Mineral Industries" two fundamental classes of manpower are encountered. These are: 1) The Labor Force, comprised of unskilled and semi-skilled, nonprofessional personnel who participate in conducting economic, mineral deposit operations and; 2) The Professional People involved in the science, engineering, and management of such industrial enterprises. The commentary given here will be directed primarily to a review of the characteristics of the second or latter class. To pursue successfully a career as a scientist or engineer in today's industrial and social complex, it is necessary that technical knowledge must have been acquired by training and study in an institution of higher learning. Also, to act effectively, the individual must have achieved some degree of specialzation, although this element often is developed to most notable degree by post-graduate exposure and experience. In addition, and especially in the case of "management," it is desirable, indeed it is even necessary, that an individual recognize and appreciate the fundamental humanistic-sociological controls, and their nuances, as these elements exist to shape his total environment.

Jan 1, 1969