Search Documents

"When boring a tunnel, homogeneous hard rock is the exception rather than the rule. While contractors can set goals such as meters per month and performance incentives, it is also prudent to plan for difficult ground. A properly designed tunnel boring machine (TBM) can tackle fault zones, water inflows, squeezing ground, or whatever the risk may be. The alternative is not a good one: modifying the machine in the tunnel after bad ground is encountered. Not only does this result in increased downtime, but it also needlessly exposes the crew to the tunnel conditions. In the worst case scenario, the entire operation grinds to a halt.However, an accurate GBR cannot always be obtained, particularly for mountainous, high cover tunnels in remote locations. And even with a thorough GBR, unforeseen geological events can occur. What can be done in these situations? Difficult Ground Solutions (DGS) is ground investigation system with a suite of options that can be added to a shielded hard rock machine or dual-mode, Crossover machine to better enable advance when conditions are unknown or difficult conditions are anticipated.DGS consists of a set of integrated features tailored to a specific project’s geology. The main components of the system allow for ground investigation ahead of the TBM, increased monitoring and methods to keep a machine shield from becoming stuck.In fault zones and squeezing groundIf fault zones or squeezing ground are known or suspected, or if there is even a possibility of encountering them, this can greatly affect the TBM operation. Shielded machines protect the crew from the surrounding rock, and they can bore and line a tunnel efficiently, but in fault zones and converging material their shields can be their downfall. Avoiding a stuck machine is paramount to project success. DGS employs several features to avoid the problem of a machine becoming stuck. The first of these is multi-speed cutterhead drives. These drives effectively give the machine multiple modes of operation—high speed, low torque for hard rock, and low speed, high torque for difficult ground. Designing a machine with high-torque, continuous boring capabilities allows that machine’s cutterhead to restart with break-out torque in difficult ground. The net effect is that the machine can keep boring in the event of a face collapse and can bore through fault zones and running ground where the potential for cutterhead jamming exists. Going one step further, multi-speed gearboxes give the machine the ideal earth pressure balance- (EPB-) type torque if larger sections of soft ground are anticipated.Secondly, TBMs can get through squeezing ground and faults using Continuous Shield Advance. This design utilizes a stepped shield configuration — where each successive shield is slightly smaller in diameter — to avoid becoming stuck in converging ground. External shield lubrication is an added insurance against becoming stuck, using a series of radial ports that can pump Bentonite into the annular space to act as a lubricant in squeezing material.As a last effort, if a machine has already become stuck the TBM can utilize augmented, or “super” thrust. Additional thrust jacks can be added to supply an extra boost in a short stroke, generating enough force to break loose a trapped shield."

Jan 12, 2017

By J. A. Brierley, S. R. Hutchins, C. L. Brierley

Introduction Many gold and silver ores are refractory to conventional processing technologies. Thus, precious metals recovery is uneconomic. These resources can consist of ores, flotation concentrates, mill tailings, and other reserves. The refractory nature of these materials can be ascribed to such components as iron sulfide minerals, silica minerals, tellurides, organic compounds, and sulfosalts. Precious metals locked within iron sulfide minerals account for a large number of refractory gold ores. These minerals consist principally of pyrite or arsenopyrite. They must be oxidized to liberate the encapsulated precious metal and allow its contact with the leaching agent. Carbonaceous gold ores represent a unique class of refractory precious metal ores in general. Not only does gold encapsulation by iron sulfide minerals occur (Hausen, 1985), but these ores also contain organic matter that interferes with gold recovery by cyanidation. Direct interference can be attributed to either occlusion of gold within organic matter or formation of a stable gold-carbon complex. The magnitude of this problem is debatable. Wells and Mullens (1973) examined two carbonaceous gold ores and found no association between the gold and carbonaceous material. A more common problem is indirect interference, whereby the aurocyanide complex formed during cyanidation is sorbed by the native organic matter and is not available for recovery. This phenomenon is referred to as "preg robbing" (Osseo-Asare et al., 1984; Hausen and Bucknam, 1984). Guay (1981) summarized various methods that can reduce preg robbing during processing of carbonaceous gold ores. However, some are not applicable to carbonaceous ores that have significant amounts of gold locked in iron sulfide minerals. Several methods exist for oxidizing iron sulfide minerals and rendering refractory precious metal ore amenable to conventional recovery processes. These include various embodiments of roasting (Jha and Kramer, 1984; Brown, 1984; Arriagada and Os-seo-Asare, 1984; Smith, 1986), pressure oxidation (Muir et al., 1984; Beattie et al., 1985; Thompson, 1986; Weir et al., 1986; Argall, 1986), and chemical oxidation (Scheiner, 1971; Jackson, 1983; Van Weert et al., 1986). Each process has been successfully used for refractory precious metal ores. In many instances, however, their use is precluded by capital and operating costs relative to the value of the ore. An alternative to these methods is microbial pretreatment - a biological process whereby iron sulfide minerals are degraded and the liberated precious metal values can be recovered by conventional technologies. Bioleaching refractory precious metal ores is a relatively new concept compared to roasting and chemical oxidation. It is rapidly becoming established as a viable pretreatment alternative. Numerous studies have been conducted in the laboratory and on a pilot scale (Yudina et al., 1979; Lawrence and Bruynesteyn, 1983; Pol 'kin et al., 1985; Marchant, 1985; Livesey-Goldblatt, 1985; Gibbs et al., 1986). Comparative tests have demonstrated that bioleaching can be equal to or better than roasting or pressure oxidation in terms of product recovery and process economics (Fridman and Savari, 1983; Livesy-Goldblatt et al., 1983; Karavaiko et al., 1985; Gilbert et al., 1986; Hackl et al., 1986). Bioleaching's main drawback is that pretreatment requires days rather than hours. This can lead to excessive operating costs for difficult-to-treat ores. In all of the tests reported thus far, the leaching microorganism used has been thiobacillus ferro-

Jan 4, 1988

By Jeffery Leavy, Ken Davis, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) is a United States Department of Energy facility located in southeastern New Mexico. It is designed for the safe disposal of transuranic radioactive waste in deep geologic salt beds. Westinghouse TRU Solutions, LLC, the managing and operating contractor, undertook a project to simulate the processes at WIPP in order to identify bottlenecks and optimize available resources. The activities simulated in the model included the receipt, processing and disposal of radioactive waste underground, the mining of new areas for future waste disposal and the transportation of salt out of the mine. The complexity of the processes and the interactive requirements between processes required the use of advanced modeling techniques. The simulation model includes a huge number of locations and path network node points, with movement to and from the locations controlled using parameters rather than explicit routing. Information for the timing and sequence of the mining and nuclear waste emplacement operations is brought into the model via spreadsheets. Arrays in the simulation model keep track of past and future events that occur. Routing to the multiple possible positions in the underground mine is done using attributes, and system functions within ProModel in order to allow for a highly flexible sequence of planned events and to reduce the level of effort in creating the ProModel processing. Considerable use of subroutines in the simulation model is utilized for parametric decision-making that is repetitive. This presentation describes the modeling techniques used to accurately simulate the surface and underground operations. The surface and underground operations are considerably different, thus they will be treated in their own sections.

Jan 1, 2002

By Robert F. Baker

Neanderthal technology is a harsh and inaccurate way to describe modern underground construction and mining practices, but such an exaggeration helps to focus on a major problem or wasted opportunity of modern society. Why is it not safer to excavate in the underground? Why are the working conditions still so unfavorable? Why are urban freeways, shopping malls, warehouses, power plants, sewage disposal treatment plants, and similar facilities still constructed on the surface of the ground--because it is a better location? On the contrary, if underground technology made full use of existing knowledge, underground resources and space would be much more effectively used. And why is the technology so inadequate? Certainly, researchers and practitioners are aware of the shortcomings and are equally aware of problems that have to be overcome. One of the most important reasons has to do with the type of policy goals that society has set in the past. Policy makers may have agreed that improvements would be desirable but no serious commitments have been made--that is, there has been no major allocation of resources to advance these technologies. And yet, to bring about significant changes will require significant time and resources. The resources that are needed are far in excess of what industry can afford to invest, particularly since the pay-off may be far in the future. So the problem reverts to society in general. As long as society is willing to tolerate the present costs and safety requirements for recovering minerals and for constructing underground facilities, then the changes will be slow in coming. Until such time as society sees and desires the benefits

Jan 1, 1974

By S. D. Morrison, J. L. Watson

It is well known that the density and viscosity of a mill pulp have optimum levels for grinding efficiency, and sophisticated control loops are employed to control pulp density in industry. However, these control loops rely on a number of plant measurements, and often the input data will not permit effective determination and control of the mill pulp density. The use of a single remote pulp density measurement has obvious advantages, and it is suggested and demonstrated for laboratory batch grinding that mill noise measurements can indicate the effective density of the mill pulp. In addition, the mill noise is shown to indicate the actual effective pulp viscosity in the mill and hence permit the identification of the dynamic rheological regime existing in the mill. It is demonstrated that mill noise increases with grind time and, at any given grind time, with increasing pulp density in the pseudoplastic range. This increase in mill noise level with pulp density is interpreted as indicating a decreasing pulp viscosity. The results show that the transition from dilatant to pseudoplastic conditions within the mill, with increasing pulp density, can be identified by this increase in mill noise. When the pseudoplastic pulp started to exhibit yield characteris- tics, the mill noise fell dramatically. The technique of mill noise analysis is then used to investigate the effect of a grinding additive on the batch grinding of two ores. With a magnetite ore, the additive was shown to increase the mill noise, and hence decrease the pulp viscosity, in the pseudoplastic region and to increase the effective grinding. The molybdenite ore, however, did not show significant noise level changes and did not show improved grinding efficiency.

Jan 1, 1987

By R. W. M. Lai

In flotation or hydrometallurgical leaching of minerals, the cumulative metals recovery for a given process condition generally approaches a maximum value or an asymptote as the process time increases. This paper discusses the experimental methods of identifying and obtaining the asymptote of metals recovery through kinetic studies. In flotation, the kinetic asymptote of metal recovery, or ultimate recovery, is a function of grinding and collector dosage, but within a realistic variable range, is not a function of pH or temperature. However, variations in grinding, collector dosage, pH and temperature, all exert noticeable effects on flotation kinetics. Frothers generally have a minor affect on the asymptote, but have a major affect on flotation kinetics. The asymptote from batch flotation is found to be identical to that of a continuous flotation. In hydrometallurgical Leaching, the asymptote of metal recovery for a given leaching system is a function of such variables as temperature, particle size, and acid concentration.

Jan 1, 1983

The structure of a mine ventilation network (M.V.N.) can be represented graphically using either the mine plan (map) itself or a number of other types of diagrams. In the U.S., the two most common approaches are the line and the schematic diagrams (see Figures 1 and 2). The purpose of this paper is to introduce another type of diagram, called the canonical diagram (6). The method of M.V.N. representation which uses canonical diagrams is used extensively in Europe, and especially in Poland, where it was developed. The canonical diagram is a noncalibrated topological image of a ventilation system. It gives a simple representation of the ventilation network, allows for the classification of currents within it and enables rapid computer analysis and computation, as well as the representation of the results. It is especially useful in studying and controlling the air flow, and it may be a life saving tool in conducting rescue operations during and after mine fires.

Jan 1, 1986

By W. J. D. Stone

Many of the common valuable minerals have a magnetic susceptibility which is sufficiently high to render them amenable to magnetic separation. In addition,, many minerals which form the unwanted constituents of an ore can be removed by magnetic means. Magnetic separation in general has suffered seriously from, the lack of a high intensity wet separator. It is only recently that such a separator has become available to the industry. Prior to this, high intensity magnetic separation has been limited to the use of the dry techniques. Since the introduction of the Jones Wet High Intensity Magnetic Separator, extensive test work has been conducted to investigate possible applications. From the investigations conducted and the discussions that have taken place in the industry, it is apparent that the important mineral characteristic of magnetic susceptibility is not receiving the attention that it deserves. Applications for high intensity wet separation are being found in areas hitherto not considered.

Jan 1, 1963

By Ralph M. Stricklen

The need to move large tonnages of slurry has grown as mines have become larger. As existing tailing depositories are filled up, new mines developed, or environmental requirements dictate, it becomes necessary to transport tailing particularly over longer distances. A typical slurry transport system is shown in Figure 1A. Figures 1B, 1C and 1D show sketches of the system auxilliary components: feed box, receiving sump and drop box, respectively. There are two basic types of slurry transport systems, packed flow and slack flow. Packed flow is typified by a pipe running full; slack flow by a launder or pipe running less than full. Slack flow in launders or channels is also referred to as open channel flow. Generally slack flow slurry transportation involves a flow with less than 65 per cent solids, and there is an upper limit on particle size, depending on the slope of the system.

Jan 1, 1984

By James L. Coburn

Leaching is defined as a form of extraction in which a valuable constituent is removed from a solid body by mass transfer to a solution which, for the purpose of this discussion, is considered to be an aqueous medium. Historically, leaching has been applied to the recovery and purification of many elements. This paper, however, is directed toward the recovery of copper, uranium, vanadium, and precious metals included in the following systems: 1. The leaching of copper minerals, sulfides and oxides, by acid or by ammoniacal leach solutions with or without an oxidant. 2. The leaching of gold and silver, either native metals or as minerals by an oxygen-containing alkaline cyanide solution. 3. The solubilization of certain uranium and vanadium minerals by oxygen or oxidant-bearing lixiviants. Many other systems of this general type exist, but from a production standpoint, these three systems account for most of the major values recovered by leaching.

Jan 1, 1975

By S. Lin

Fan stall is a notorious phenomenon with axial-flow fans. When multiple fans of this type serve a ventilation system, their mutual impacts are very complicated and not well understood. Results from laboratory experiments indicated that the immediate consequence of a fan working across its stall zone (i.e., the pronounced trough on the fan characteristic curve) is that some branches in the system may suffer abrupt and even drastic changes in air quantity and pressure. The quantity range of the fan that causes the abrupt change is called an unstable operating range. The corresponding quantity range of a branch is called a non-achievable quantity range of the branch because any quantity within this range cannot be achieved without changing some parameters of the ventilation system (e.g., branch resistances). These concepts are introduced based on the test results from tubing networks to bring attention to these important characteristics of ventilation systems.

Jan 1, 1996

By A. K. Bhowmick

Size reduction is very energy intensive and is the single most power-intensive operation in mineral processing plants. Research has shown that only a small part of the energy is utilized efficiently. One of the major thrusts of all equipment manufacturers has been to improve this efficiency. Choosing the right equipment to maximize energy utilization in any comminution application has always been the utmost criteria. Due to the high energy cost and depletion of good grade minerals, it is becoming essential to optimize all the subsystems within a given comminution system for the overall economic success of such ventures. Bradley Pulverizer Company of Allentown, Pennsylvania recognized this and started offering its Feeder Controller in 1988 for automatic feed control. After its first successful operation, Bradley made this as a part of all of their grinding system standard offering. It was also recognized that the Feeder Controller was just a beginning and more automation and controls would be required for an overall, efficient grinding system.

Jan 1, 1993

By Armando M. Lago

This paper reviews the postwar changes that have occurred in the expenditure and financial behavior of mineral corporations, and in particular the relative importance of factors that affect the industry's supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample in Section I, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail in Section II. Section III formulates an econometric model of mineral corporate financial behavior which is then estimated and reviewed in Section IV. Section V discusses policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector. Finally, the optimum financial structure of mining firms is discussed in Section VI, which analyzes the effect of corporate financial structure on the mining corporations' average Cost of capital.

Jan 1, 1969

By James P. Dorian

Dramatic economic and political reform is under way in the transitional economies of the world. Transition extends beyond the restructuring of a nation's economy and political thinking. It also affects social, cultural and even religious aspects of society. Transition is a long-term process and generally unstable as the pace of reform is rarely the same across the many spheres of society. As nations modify their economies, industrial activities - including minerals exploration, extraction, processing and trade - are also being affected, according to a Financial Times of London management report. Mining policies are being revised to encourage greater foreign involvement, while legal regimes are being rewritten to protect foreign investments. From India to Peru, and South Africa to Russia, countries have been preparing, improving and expanding foreign investment laws, mining codes and economic stimulus measures to accelerate their minerals development. Privatization of mining is proceeding in many nations. Meanwhile, corporatization of former ministries and government agencies responsible for mining is also occurring. According to Minerals and Mining in the Transitional Economies: Poised For the Future, common objectives in the restructuring of a mining industry are to enhance overall economic and industrial growth, improve efficiencies in mineral recovery and use, acquire newer, advanced technologies, reduce environmental repurcussions of mining and improve safety conditions. The nature of mining is changing noticeably within the transitional economies. The industry is becoming more re¬sponsive to market forces and private sector concerns. The new report examines the changing characteristics of mining in the transitional economies. These include nations moving from centrally planned to market economies, as well as countries in the midst of economic and political reform, including the liberalization of industry. Information is presented to help business planners understand the impacts of transition on mining activities and re-evaluate their longterm strategies and market development policies. The document is divided into 10 chapters. Five of them are devoted to the evolving mining industries of Russia, South Africa, India, Peru and China. These countries were highlighted because their minerals sectors are undergoing changes. These include the opening up of their resources to foreign mining companies. According to the report's author, mining in the transitional economies during the next decade will be characterized by: ? Continued rewriting of national mining policies to create more favorable investment climates. ? Increased exploration for gold and selected base metals in newly opened regions. ? Innovative project financing schemes involving multiple partners and international lending institutions, such as the European Bank for Reconstruction and Development (EBRD). ? Increased gold and copper ore production capacity resulting from new investment and expansion of existing operations. ? Continued geographical shifting of metallurgical processing facilities from developed to other mineral-producing nations. ? Privatization of state-owned mining and processing assets requiring advanced technologies for improvement or expansion. ? Increased awareness of environmental concerns in business decisions related to mining and metallurgy.

Jan 1, 1997

By Charles H. McGuirk

The movement of iron ore, limestone and-coal on the great lakes involves an intricate transportation network between mine, dock, vessel, railroad and consumer. The system requires that stockpiling be performed at certain points in the pipeline because of the seasonal closing of the lakes, traditionally, this has been accomplished at origin and destination with a substantial cost. Impact to both the shipper and consumer, From the time that the raw material is removed from the ground, expeditious handling and movement to final destination is threatened by a series of potential delays. An initial movement from mine or processing plant to the upper lake port must be coordinated between rail equipment and dock facility, As each vessel is loaded, a schedule must be developed which routes the cargo to an unoccupied lower lake port. However, if the vessel is not delayed by unpredictable weather conditions on the lake, the boat may still arrive at a port congested with other vessels awaiting their turn to unload.

Jan 1, 1973

By N. J. Peberdy, C. N. Moreton, K. C. Garner

Introduction During the past decade a major objective of the process industry has been to use digital computer technology to improve plant operating efficiencies. This objective implied some form of optimization, a concept that has various interpretations depending on the view of the prospective user. For the purpose of this paper, optimization of a process plant is defined as the establishment and setting of plant operating conditions that maximize some mathematical yield function, i.e. maximum profit, minimum residue, etc. Analysis of these objectives and the available design and implementation techniques led to the conclusion that digital computer and optimization techniques are not the stumbling blocks, but rather the development and derivation of the mathematical models of the unit operations and process plants to be optimized. Such models should not only describe the optimized (steady-state) objective, but also how one steers to this state (control algorithm). Due to the multidisciplinary nature of the skills associated with the design and operation of process plants, the development of suitable models by a single discipline, such as the process control engineer, was found to be not only difficult but often impossible, due to budget and human resource limitations. To over-come these limitations, a computer aided design (CAD) tool has been developed. It aims to provide a productivity tool to the various disciplines, at the same time coordinating the technical input from each. The system described is but the starting point in an evolutionary development of a tool that, with use, is becoming more efficient and cost effective to use. Development has become an application engineering activity rather than the preserve of the computer specialist. Project phasing The development of a mathematical description of a process plant requires coordination of information from conceptual design to operation management. The activities required to build and operate a process plant are divided into four basic chronological activities or phases. These activities are often undertaken by different organizations and disciplines. As a result, continuity is often lost with the resultant loss of critical design data. The major activities are considered to be: conceptual and flowsheeting; detailing around the P & ID; building and commissioning; and plant operation. The CAD system described provides a design tool to be used for each of these activities, as well as providing continuity between the activities and the disciplines involved. The heart of the system is the dynamic simulation of the flowsheet. Each of the activities will be discussed, leading to two simple examples that demonstrate the use of the simulator. Figure 1 shows a schematic format of the various activities and the path followed by the dynamic flowsheet simulator in the life of a project. Flowsheet development The prime requirements in the design and develop¬ment of a process flowsheet are • selection of the correct unit operations to achieve the most economic (capital and operating) beneficiation of the specified reserve ; • the sizing of the unit operations to achieve the desired results, as a function of the projected feed rates etc., to handle the time related (dynamics) of the process; and • the production of a set of engineering documents showing the drawn and labeled flowsheet with an equipment list and process specification for each of the unit operations. The question may well be asked at this stage why dynamic flowsheet simulation should be considered when steady state modeling has been found to be adequate to date. With the increases encountered in the cost of capital, one often cannot afford the luxury of designing around the compounding worst case technique. Further, a more accurate design of the control surges can be achieved. No information is lost in that the steady state solution is in fact a subset of the dynamic model. In generalized state space modeling, the differential equations describing the process dynamics are illustrated in the following matrix notation: XDOT=A.X+B.U(1) Y =C.X+D.U(2) where XDOT describes the set of first order derivatives of the system state Vector, and X- is the system state Vector; A - is the system matrix operator which in the general nonlinear case is both a function of X and time ; U- is the process input vector; B - is the input mapping matrix; Y - is the set of observations; C - is the output mapping matrix which maps X - onto Y; and D- maps the input onto the observations. Thus, by time integration of the system dynamic equations, described in (1), the dynamic trajectory away from any set of initial conditions can be deter¬mined. Further, by finding the conditions at which XDOT = 0, the steady state solution can be determined.

Jan 1, 1987

This paper presents a method for evaluating the economic feasibility of solution mining a hypothetical uranium roll-front deposit. It is assumed the wellfield will be operated in a prudent manner and that leaching tests were performed in depth in both lab and field (push-pull) prior to startup. Leach test results are reduced to two important parameters and used as the basis for solution mining a wellfield. This case study assumes a 10 mil- lion-lb uranium deposit with 40 possible small wellfields; four are kept in operation simultaneously until the deposit is depleted. The wellfields have different ore reserves and grades, lixiviant circulation rates, leach rates, and peak concentrations, and thus the daily uranium production will vary. Daily production is used to assess the profitability of a particular lixiviant and the mode of well- field operation in light of realistic market price estimates. The mathematical procedure is simple and straightforward, based on reasonable in-situ leaching relationships as well as accepted accounting practices.

Jan 1, 1985

By Grover H. Emrich

Pennsylvania,, due to its location in the humid east, is fortunate to possess within its borders large quantities of water. Most of the State is drained by three major river systems-the Ohio, Susquehanna and Delaware. This abundant supply of surface water has been widely utilized throughout the State, but today other sources of water must be developed due to the increasing demands for water, die largest undeveloped source of water in Pennsylvania is ground water. Pennsylvania is also fortunate to possess extensive coal resources. These coal resources have contributed measurably to the development and prosperity of the States Coal and water's - two valuable resources - have been necessary for the development and industrialization of Pennsylvania, The State needs both resources but can no longer afford to develop one while adversely affecting or destroying the other, We are aware of the effect of coal mining on surface water, but coal mining can also materially affect subsurface water, This effect will according' to the local geologic conditions.

Jan 1, 1965

By R. S. Shoemaker

Expanded markets for copper in the past few years and a consequent search for new ore bodies have revitalized the widely known but seldom applied method of producing copper called heap leaching. This term should be differentiated from dump leaching in that the latter is applied to dumps of mixed oxide and sulfide ores (although either may predominate) that have been too low grade to beneficiate and have, therefore, been stripped off the higher grade underlying sulfide ores. Heap leaching is defined here as the process applied to oxide ores which have been mined solely for the purpose of leaching. In this case, all costs of mining the ore become a part (and a substantial one, as will be shown) of the cost of the copper produced, whereas in dump leaching the mining cost has already been accounted for as a stripping cost for the sulfide ore. Of course, with newly opened ore bodies, stripping costs may be divided through accounting procedures, between the copper produced by the mill and that obtained by leaching, but in general this type of operation must be economic on the basis of the sulfide ore alone. Heap leaching, as a beneficiation method, is unique in that it is the only process used for the recovery of a metal in which the time involved from mining the ore to metal production is measured in months instead of hours or at the most, days, Then too, after the ore body has been depleted and mining has ceased, metal production will continue for some substantial period of time. Heap leaching is also unique because unlike any other method of beneficiation, metal recovery cannot be accurately forecast ahead of time and recovery will never approach that of a conventionally milled sulfide ore or even that of a vat leached oxide ore. Counter-balancing this drawback, however, is the relatively low capital expenditure necessary to put a heap leaching operation into production and the consequence that smaller ore bodies which would not support the higher capital cost involved in a vat leaching plant can be made into producers. Stated more simply, in heap leaching the operator accepts low recovery in exchange for low capital costs and the break even point, that is, where the operator should go to vat leaching with its higher recovery and higher capital costs, is a matter of economics and also, to a great extent, a matter for the nature of the ore to decide. For instance, an ore that will vat leach in 7 to 10 days using 7 pounds of sulfuric acid per pound of copper produced might use double or triple that amount of acid during the months that are required for heap leaching.

Jan 1, 1968

By W. W. Bristol

The Jerritt Canyon Joint Venture project is located approximately 50 miles (80 km) north of Elko. Nevada, U.S.A. and produces between 250 and 300 thousand ounces of gold annually. The Joint Venture is 70% owned by Independence Mining Company and 30% owned by Meridian Gold Company. Independence Mining Company is the operator. The Jerrin Canyon Joint Venture started operations in 1980 mining a series of open pit mines. Since the early 1990's, the discovery of deeper ores has required the joint venture to develop and mine a significant portion of its annual production utilizing underground mining methods. Underground production started with the West Generator Mine in 1993 followed by the Murray Mine in late 1994. Presently, two additional underground projects are being developed. Underground mining at Jerritt Canyon is budgeted to produce 128 thousand ounces in 1997. This paper documents the major transition/redevelopment of the Jerritt Canyon mining methods.

Jan 1, 1997