Search Documents

By R. S. Austin

One-third of the world's and most US kaolin is produced from Late Cretaceous and Early Tertiary sedimentary strata in Georgia and South Carolina. The kaolin is part of a belt extending to Arkansas of aluminous lateritic deposits, including bauxite. Original sediments were profoundly altered by chemical weathering during Early Tertiary time. Mining exploits those uncommon deposits where extreme leaching and chemical recombination have produced a clay of nearly pure mineral kaolinite. Properly selected and refined, kaolin is an important pigment, filler, extender and chemical compound in the paper, paint, plastics, ceramics and catalyst industries.

Jan 1, 1998

By L. M. English

When plotted as head vs. volume, fan curves start high and decrease in head with increasing volume while mine head curves start low and rise with increasing volume. Their intersection is the system operating point But wait a minute: Isn't head loss a negative number, a debit? And isn't fan head an energy addition, a credit? This, as every ventilation instructor knows, is often a stumbling block to student or audience comprehension. It is possible to use the intuitively correct curves -pressure losses as negative values and energy additions as positive values -and still obtain the correct operating point: adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at \\tIich the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure; with the standard approach it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel circuit or ventilation net\wrk. The results are the same, and the approach is logically consistent and less confusing.

Jan 1, 1997

By Ole Bernt Lile

The well-known method of C. Schlumberger, Mise a la masse, has become a popular method again in ore exploration in Norway after many years of dominance by EM methods. The principle of the method is to place a current electrode within a conducting ore body and remove the other electrode to a great distance. (Figure 1). Often it is convenient to place a return electrode on each side of the area explored. The method is best suited for ores that have a conductivity contrast, relative to the host rock, of several orders of magnitude. The potential drop within the ore itself may then be neglected and the ore contact against the rock may be regarded as an equipotential surface. One may say that the ore body is electrically charged. Therefore, in Norway the method is now most often called the Charged Potential Method (abbreviated CP). The most usual way to present data obtained by CP, is to draw equipotential lines based on potential values measured in profiles on the surface. Such a potential map gives an immediate picture of the outcrop of the ore and also indicates disturbing conductors in the neighborhood. It may also be useful to look at the potential profile and its horizontal gradient along the strike axis of the potential map. These profiles may give information about the strike length of the conductor. Figure 2 shows the theoretical profiles of potential and gradient along the axis of the potential picture on the surface over a charged line plunging 15 degrees. It may be seen that the maximum of the gradient curve clearly indicates the lower end of the conductor. Figure 3 shows the corresponding pro- files over a charged line plunging 45 degrees. In this case, it is not possible to see an indication on the curve of the lower end. Only curve fitting could help interpretation in this case.

Jan 1, 1975

By D. Belin

Treatment of dilute acid mine drainage and similarly polluted water is becoming increasingly complicated. The pressure of economics is now exacerbated by legislation which classifies as hazardous waste the precipitates from conventional lime treatment plants. Since acid mine drainage invariably contains sulfate ions, one solution is to use anaerobic Desulfovibrio type bacteria to reduce the sulfate into sulphide ions which could then be used to precipitate out the heavy metals. Results are presented for both batch flask cultures and continuous column tests. Compost was used as the bacterial substrate in the column test which simulated heaps. Conditions changed from aerobic to the required anaerobic deep in the columns. Polluted feeds (up to 700 mg/l zinc) gave effluent containing well below I mg/l zinc over extended periods. Direct transfer of sulphide ions through a stream from an isolated container of bacteria is a good alternative.

Jan 1, 1991

By C. J. Johnson

As the U.S. coal industry moves into the next century, it is becoming more apparent that the effective application of new technology is the only way it can remain competitive in the energy marketplace. Examples of this emphasis are with us today in such diverse areas as face-ventilation and excavation-equipment applications. The focus of this new technology is directed toward improvements in health and safety, cost control, and productivity. Room-and-pillar mining accounts for approximately 80% of the nation's underground coal production; this percentage is not expected to decrease markedly in the near future. As such, this paper analyzes the impacts of the changing technological climate on future room-and-pillar operations by comparing a base-case section (current) to three scenarios incorporating new or emerging technology. A microcomputer-based comparative analysis will reflect the changes in section production and costs.

Jan 1, 1988

By R. R. Klimpel

The efficiencies of plant-scale comminution processes are often evaluated by various indices calculated and/or measured somewhat independently of the performance of any associated downstream froth flotation processes. To compare specific comminution factors, such as energy utilization, media consumption and equipment utilization time, comparisons of comminution efficiency independent of flotation behavior are appropriate. However, as increasingly detailed plant-level information is gathered on the joint and highly interactive nature of comminution and froth flotation, it is becoming even more obvious that knowing and using simple efficiency indices are not enough. What is needed are more performance-related measures of the efficiencies of the combined size reduction froth flotation system for effective plant-level economic optimization to occur. The purpose of this paper is to present examples of some of the important interactions that influence the joint efficiencies of size reduction and froth flotation processes.

Jan 1, 1999

By Uday Kumar

This paper presents details of an availability study for a fleet of diesel engine operated load-haul-dump (LHD) machines used in a Swedish mine. For the purpose of this study, the LHD machines have been considered as a system comprised of many subsystems like engine, brake, transmission, etc., in series. As availability is dependent on both the reliability and maintainability characteristics of the system, together with reliability, the concepts of maintainability are also discussed. The need for exploring the data for the presence of any structure, which is very common in repairable system data sets, is emphasized with suitable examples. Simple graphical techniques are used for verifying the independent and identically distributed (IID) assumption for the data set. The error introduced due to the use of the exponential distribution in place of more appropriate distributions in estimation of availability and reliability characteristics is analysed.

Jan 1, 1989

By William J. Bryson

Just picture, if you will, the hot, lonely and desolate Ochre Mountains west of Salt Lake City. There works a grizzled old miner, his boots worn down, his clothes hang on a body stooped by years of hard labor. His skin is wrinkled and leather toughened by many years in the hot desert sun. His ever faithful burro stands patiently in the shade of a large rock as the tired old miner examines ore samples just acquired that very morning. Suddenly the old man's eyes widen, his breathing becomes rapid. 'Leaping to his feet, with a gleam in his eye, he cries, "Eureka, I'm rich, I've found the mother lode. This is where I will start my digging. " Without warning, the silent wilderness is alive with wild, shouting, charging figures! Frightened the old miner glances about him wide-eyed and pan- icky. His heart sinks, dismayed he now knows all is lost, this is the end. For there leaping from behind rocks and brush papers in hand, are the men from the Department of Interior, Bureau of Land Management, State Mine Inspectors, OSHA, MESA, EPA, OEO, and the never ending list of regulatory bodies related to todays mining industry.

Jan 1, 1975

By Douglas J. Piper

On reflection of certain overall circumstances which have pervaded the gold mining industry, it appears useful to point out some specifics which the writer hopes will improve the potential for success in the application of hydraulic dredges to gold mining activity. I will, prior to entering into that discussion, comment briefly on rule of thumb for the application of the three types of equipment. The three are bucket line, bucket wheel and drag line dredges. From a standpoint of high volume movement over a short distance, between 50 and 300 feet, the drag line dredge is historically the most cost effective type of machine to be utilized if bulk excavation is the single driving consideration. It is typical for this sort of equipment to operate in the 10 to 30 cents per cubic yard range, however, cost of operation is not the sole consideration. Typically the drag line mixes and remixes the material which it excavates. In the event that gold recovery is the object of the exercise, a strong potential for loss of the valued mineral exists. Additionally, drag lines do a poor job of bottom cleaning, particularly if there is a ridged or creviced bottom which must be cleaned and in some cases partially removed to assure recovery of the highest percent of valuable ore. The bucket line dredge has, until recently, been considered an extremely cost effective device. However, the high cost of manufacture of this type of equipment has mitigated against its use in the majority of

Jan 1, 1992

By Ann M. Gosier

Over the past 20 years, diesel-powered equipment has been introduced into the underground mining environment in increasing numbers. While the introduction began years earlier in the metal-nonmetal sector, the exponential growth in coal mining use during this time has been more pronounced. Reasons for the continued use and rapid growth of diesel equipment in underground mines are easily understood. The safety and operational advantages afforded by this equipment in production and support systems are demonstrable. As other mine operators witness the advantages enjoyed by their competitors, they too move to introduce an increasingly diverse array of such equipment into their underground mines. As with any industrial technology, the use of diesel-powered equipment entails potential safety and health concerns. Existing Mine Safety and Health Administration (MSHA)approval regulations (30 CFR Parts 31, 32 and 36) apply only to diesel locomotives and mobile diesel-powered equipment for noncoal mines. In the absence of specific regulations, MSHA has required the use of equipment approved under Part 36 (gassy noncoal mines) for areas of underground coal mines where permissible electrical equipment is required. However, a considerable amount of diesel-powered equipment without explosion-proof or fire prevention features is in use in areas of coal mines where permissible electrical equipment is not required. It is on the use of this latter class of equipment that MSHA is focusing much of its regulatory attention relative to coal. The agency also is focused on revising existing occupational exposure limits for gaseous emissions and instituting limits on diesel particulate emissions for both coal and metal-nonmetal mines.

Jan 1, 1993

By H. W. Gussmann, R. G. Rohrs, E. van der Merwe

Salinity in Effluents carries a high penalty as a result of toxic­ity, corrosion, limited re-use potential, scaling and environmental impact. Although the high TDS, such as Calcium sulfate, other than metals are still being dealt with a low key non issue basis, they are receiving more and more attention from regulators. Traditional solutions to solve these problems are costly and inefficient and create therefore severe constraints on the prof­itability of mining operations and out-price in general the finan­cial resources for environmental clean up operations. Going up the technology versus cost curve the most econom­ic solution to pollution is dilution but which is difficult in a coun­t1y shoti of water. If this can't be done, the second best, at least in sunny areas, is, to pump the whole effluent on a tailings dam for evaporation. Depending on the contaminants, one may have to pond the efflu­ent to avoid re-dissolution and seepage into the ground. The next most common solution to pollution is the addition of lime to remove and concentrate any dissolved metals and then dump the product, hidden in a mass of gypsum in a convenient place. Again ponding may be required to avoid ground pollution. However the treatment costs start to rise steeply if it is not allowed to discharge the limed overflow solution because of its high calcium sulphate content. Further treatment is then required in the form of high cost and high tech membrane process tech­nology such as reverse osmosis or dialysis or even mechanical driven evaporation.

Jan 1, 1998

By Charles H. Jacoby

Introduction Although, in general, the openings created in domes or diapiric type salt deposits during mining operations are larger than those created in bedded deposits, the openings in bedded salts are of significant lateral extent. Thus, this paper will deal primarily with the dome deposits of the Gulf Coast and more specifically with the Avery Island dome operated by the International Salt Company where recent development activities have materially increased the sizes of previously standard openings. Geology The geology of salt deposits is the governing factor in the rock mechanics associated with the opening which is being created in the salt. Bedded salts are customarily characterized by having experienced solution along the interface between the top of the salt and the overlying bed. Thus, as the salt slowly dissolves there has been left behind a layer of laminated insolubles which is often incompetent. In most cases, this incompetent rock must be supported by a thickness of bedded salt which is left in the roof as support. Where this salt is of secondary deposition (recrystallized halite) with included moisture, additional thicknesses of roof salt are necessary to achieve stability. The salt which forms the domes of the Gulf Coast regions is from the Louann formation of the Jurassic period. These formations are dipping toward the Gulf of Mexico so that the upper tier of domes which have formed across northern Louisiana in an east-west direction into Mississippi and Texas have a salt source some 10 to 15,000 feet

Jan 1, 1976

By John H. Duke

The success of most attempts to evaluate gold orebodies depends largely on the reliability and availability of representative sampling data and the accuracy of geological interpretation. An accurate prediction of the continuity of geology is paramount to a reliable prediction of gold reserves. Many of the problems encountered in gold mine evaluation and planning revolve around the difficulties in interpreting complex geology from sparse drilling data and the eagerness of mine financiers and promoters to start mining in order to derive an early cash flow. Following a program of sampling, geophysics, mapping and geological interpretation, a conceptual orebody model evolves in the minds of those working on the project. It is this model which is used typically in ore reserve computations and mine planning. Computer modelling techniques to represent and evaluate the conceptual model are now available. The main advantages of using computer modelling methods lie in being able to rapidly evaluate, modify and quantify the conceptual orebody model. Ore zones or domains can be recognised and defined both from geology and sampling results. Once these domains are defined as a series of boundaries, they may be modelled as two dimensional grid surfaces or as wire-framed three dimensional geometries, depending on the complexity of the orebody. It is the definition of these domains which provides the sound geological basis for reserves computation. To estimate reserves it is necessary to determine both volume of ore and grade of ore. The ore volume is calculated within each domain as defined by the confining surfaces or wire-frames. The ore

Jan 1, 1987

By Rodolfo V. de la Cruz

The broad front concept is based on the principle that gasification can be achieved more efficiently and completely from a plane broad combustion front in contrast to other geometries obtainable with current methods of gasification. By restricting combustion to a plane broad front, the ideal condition for gasification is achieved. A plane broad combustion front can be developed in coal by initiating and propagating combustion from the walls of an oriented channel and collecting product gases from another similarly oriented channel. Flow will then be directed along the highest permeability of the coal bed, the available cross-sectional area for fluid flow is substantially increased and, more importantly, the increased flow will be uniformly distributed throughout the whole mass of coal. The success of the method is greatly dependent on how well an initial and rigorous permeability survey and associated corrective measures yield a well-characterized coal bed. To maintain uniform reaction rates, the advance of the combustion front is located with pressure- or mass flow-transducers. These sensors are then connected to servo-controlled mufflers for controlling segments of the fire front which are advancing ahead of others. Finally, the development of the concept to overcome problems of roof collapse, reactant and product gas leakages, and water invasion are briefly summarized.

Jan 1, 1976

By Angelus S. C. Owili-Eger

The protection of groundwater resources is a growing issue on both the legislative front and within the private sector. At present, the legislative push is to establish within the Environmental Protection Agency a comprehensive research, development, and demonstration program relating to groundwater contamination and resources. It is evident that certain aspects of such legislation will be directed at the mining industry. Consequently, the mining industry must position itself to address the issues and concerns from a backdrop of facts and knowledge by developing an integrated hydrogeochemical model of the mining environment.

Jan 1, 1989

By Fathi Habashi

CLAYS CONTAIN the mineral kaolinite, a hydrated aluminum silicate. It is an important potential raw material for aluminum, especially for those countries possessing no bauxite deposits. Therefore, there is no surprise to find a large volume of research done for the recovery of aluminum from clays. Kaolinite (Al203?2 SiO2?H20) contains 39.8% A1203; 46.3 % SiO2, and 12.9 % H2O. The analysis of a good-quality dried clay of an Eastern Canadian siliceous shale is shown in Table 8-1.

Jan 1, 1970

By Roger Beckie, Leslie Smith, Craig Nichol

To study the hydrogeological processes that control the movement of water through unsaturated waste rock, an intermediate-scale (8m x 8m x 5m) waste rock pile has been constructed and instrumented. The constructed pile is monitored for moisture content, matric suction, temperature, matrix water chemistry, gas chemistry, gas pressure, rainfall, evaporation, discharge volume and discharge chemistry. The pile is built upon a grid of 16 contiguous lysimeters. The experiment is designed to investigate the mechanisms that create rapid water flow through a pile and its exchange with slower-moving matrix water.

Jan 1, 2000

By Fred N. Kissell, Jeffery L. Kohler, Edward D. Thimons

Aerodynamic stall of vane-axial fans is both an operational problem and a safety concern. While deep stall is relatively easy to detect, the diagnosis of a partial stall is often more difficult. Its transient nature and the fact that its symptoms can mimic electromechanical problems of the fan and fan drive assembly, or vice-versa, compound the difficulty of making a timely and accurate diagnosis. A knowledge-based expert system known as FANPRO has been developed to aid in the diagnosis of these problems. FANPRO and its application are the subject of this paper.

Jan 1, 1991

By T. H. Jones

Fall of ground is a leading source of worker injury and fatality indicating a persistent need for ground monitoring technology. The HRTMM is an experimental convergence monitor utilizing a digital camera and custom software to track the position of one or more lasers across the target. Apparent laser movement is proportional to target convergence. The HRTMM was installed in an underground mine near active operations to test its response to the mining environment. This included intense blasting vibration and mine fog. Results and potential of the new monitoring technology will be discussed.

Jan 1, 2008

By K. C. Carriere

INTRODUCTION The purpose of this paper is to introduce the reader to basic control strategies for solid/liquid separation in mineral processing and to indicate some of the implementation difficulties to be encountered, without becoming overly involved in details of process, equipment or software. It is assumed that the reader has some familiarity with control systems and with dewatering processes, since exploration of these topics would require considerably more length. The paper is organized into three parts: first a general discussion on the need for control of dewatering processes and of the general criteria involved, next a more detailed elaboration on control strategies for the various unit operations, and finally a case study showing a specific approach towards such a project. Motivation & Objectives The justification for implementing any control system in an industrial plant is to improve operations and thereby to increase profitability. Without this motivation, the system will likely be perceived as unnecessary and will decline into disuse, an expensive and troublesome monument to someone's ill-conceived ideas. However, when a control strategy is correctly conceived, implemented and integrated into operations, it can provide significant advantages in operating ease and efficiency, and a handsome return on investment. In general terms, the objectives in establishing a control system are: • stabilization of process disturbances maintenance of product quality • maximization of throughput • dearer definition of process • protection of personnel and equipment A successful control strategy must address at least some of the above criteria. However, the most important requirement is a commitment on the part of plant personnel and management to start up, operate and maintain the system, and to upgrade it to reflect current process status and operational philosophy. Process Applications In this paper, control strategies will be explored for the most common methods of dewatering of mineral pulps. These unit operations include: drying, centrifuging, filtering and sedimentation. While the first three are important, they do not tend to be as complex as sedimentation, and thus will not be as exhaustively treated. Sedimentation is very widely applied, not

Jan 1, 1986