Search Documents

By J. D. Miller, C. L. Lin

Liberation of valuable minerals during size reduction is an important aspect of mineral processing technology. In practice, most quantitative information on liberation is based on the application of stereological theorems for the analysis of image data from two-dimensional polished sections. On this basis an estimate of the volumetric grade distribution is made. Recently, a new method based on cone-beam xray microtomography has been used for direct determination of the three-dimensional liberation spectrum of multiphase particles 100 microns in size or less. Preliminary results for a packed bed of particles indicate that high spatial resolution (approximately 15 microns) and the direct processing of raw volumetric data are two important benefits offered by this new method. Three dimensional liberation analysis by microtomography provides an excellent opportunity to overcome many of the limitations of currently used polished section techniques. For example, detailed textural information is provided. Of course microtomography provides an independent method to verify current procedures used for analysis and transformation of polished section data into an estimate of the volumetric grade distribution. More important, however, is the possibility that this method could be developed as a routine procedure for liberation analysis in the 21st century.

Jan 1, 1997

By W. J. Wuest, M. J. DeMarco, J. R. Koehler

Yield-pillar-based gate-road designs often fail to provide mine operators with adequate ground control. This is because of the unknowing m is employment of "critically" sized pillars. A "critical” pillar is one that is too large to either yield nonviolently or to yield before the roof and floor sustain permanent damage and is too small to support full abutment loads. To demonstrate the critical pillar concept, afield study of a tapering gate road was conducted by the US Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m (55.1-ft) wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m (40-ft) wide design more closely approaches proper yield pillar dimensions. A probe hole in several 10.6-m (34.8-ft) wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1997

By A. Hekmatnejad

"The objective of this work is to validate a methodology for spatially predicting the fracture intensity, defined as the average fracture area per unit volume. First, using the observations from drill holes, the fracture intensity is directly inferred at the support of drill-hole composites based on a Terzaghi correction. Subsequently, the composite values are interpolated to larger blocks. The methodology is tested on sets of simulated fracture networks, in which each fracture consists of a disc with a random diameter, random position and random orientation. For each of these simulated networks, one can calculate the actual fracture intensity within any region of space, based on geometric considerations. A regular sampling mesh is then defined to emulate a set of vertical drill holes and the proposed methodology is applied to predict the fracture intensity, both globally and locally. The actual and predicted fracture intensities are finally compared, showing that predictions are unbiased, insofar as, on average, the prediction error is always close to zero. Also, the error dispersion increases when the support of the prediction decreases, which is consistent with the well-known support effect. In practice, the proposed methodology allows predicting fracture intensity based exclusively on drill-hole information, without the need for simulating fracture networks in space, hence its interest. INTRODUCTION The characterization of fractures in rock masses is an important part in the evaluation of mechanical and hydraulic properties of rocks. Fractures have a large impact in disciplines such as reservoir engineering, safety of underground storage of CO2 or of nuclear waste, assessment of high-enthalpy geothermal installations, safety of mining exploitations, efficiency of in-situ leaching operations or of extraction by block-caving. As a rock mass property, fractures must be characterized in the three-dimensional space, whereas observations are limited to 1D (drill holes) and 2D (outcrops, drift walls), moreover very often to rather short stations, so that the available data are subject to geometric bias, truncation and censoring. Fracture characteristics includes the number of fracture sets and, for each set, the number, orientation, spacing, location, shape and size of the fractures must be inferred from data sampling. Some important parameters that are considered nearly in all models are fracture intensity and fracture size."

Jan 1, 2016

By R. J. Hamilton

Considerable success has been achieved in recent years in reducing concentrations of respirable dust in UK coalmines; thankfully this has been reflected in significant improvements in pneumoconiosis statistics. However, continuous increases in mechanisation and in rates of working, accompanied by more stringent dust regulations, necessitate the introduction of improved and often more sophisticated methods of dust control. The increased application of exhaust ventilation and air cleaning techniques seems likely to be the most important step forward in dust control in coalmining during the next few years. A typical drivage in a UK mine is not more than 16 ft (5 m) wide and is supported by steel arches. In the past the majority of such roadways were driven by the conventional means of blasting and loading. Since the main purpose of ventilation was to clear blasting fumes and to provide adequate scouring of firedamp, not surprisingly it was usual to have 'forcing' ventilation. Present systems of operation are making increasing use of heading machines and it is not surprising that well over half of all drivages are now ventilated by exhausting methods. (1) The great majority of coal getting in the UK is from longwall faces, usually in seams of less than 6 ft (1.8 m) thickness. Although this method of min¬ing has many advantages in terms of safety and productivity, dust control is made more difficult because of the need for men and machines to work in the same ventilation stream. Much emphasis has been placed on improving the design and methods of opera¬tion of longwall machines to reduce dust production, and improved ventilation has provided greater dilution, and in consequence, reductions in dust concentration. On all machines water is now fed through internal galleries to the cutting elements. Unfortunately, one of the difficulties associated with mining thin seams is that there is some unavoidable cutting in the roof or floor and in many seams there are faults to be traversed and dirt bands which must be removed with the coal. Under these conditions it appears that the use of exhaust ventilation and air cleaning offers the most promising way of achieving satisfactory dust conditions.

Jan 1, 1980

By K. H. Bettles

The Goldstrike Mine is in Eureka County, Nevada, approximately 23 miles northwest of the town of Carlin. The mine is at the north end of the Tuscarora Spur of the Tuscarora mountains at elevations of 5,300 feet to 5,950 feet. It is part of the Bluestar/Goldstrike subdistrict of the Carlin Trend of sediment hosted, disseminated gold deposits. The Carlin trend comprises over 15 major gold deposits with production, reserves and geological resources of approximately 50 million ounces of gold (Fig. 1). In the Bluestar/Goldstrike subdistrict, there are four major deposits; Post, Betze, Bluestar, and Genesis, plus numerous smaller deposits (Fig. 2). Betze is located on property controlled by Barrick Goldstrike Mines; Bluestar and Genesis on Newmont Gold property; and Post on both Barrick and Newmont property.

Jan 1, 1989

By William L. Rose

Production scheduling is an integral part of intermediate- and long-range open-pit mine planning, affecting equipment selection, manpower requirements and project economics. The development of mining phases, or pushbacks, is discussed in conjunction with generating the best spatial extraction sequence. An approach to scheduling production from these mining phases is then described. Using computers and a production scheduling algorithm, the impact of cutoff grade and advanced stripping policies can be evaluated through sensitivity studies to maximize the return on project investments.

Jan 1, 1985

By Richard O. Y. Breese

Geologically and commercially, the term diatomite is applied to the nearly pure sedimentarv accumulation of diatom frustules- the microscopic skeletons of unicellular aquatic algae belonging to the class of golden brown algae, bacillariophyceae. The sediments are fine-grained, siliceous, and consist primarily of amorphous opaline silica with only minor amounts of organic residue, secondary minerals, and co-deposited non-diatomaceous or crystalline clastic debris. In the geological sense, the name diatomite implies sedimentary accumulations that have reached appreciable thickness and when thick enough, such accumulations consequently may have possible commercial potential. Although the term diatomite is popularly and inappropriately applied to any sediment in which there is an abundance of diatom frustules, alternative terminology is more correctly employed to describe the less pure diatomaceous sediments, for example: clay-bearing diatomite or diatom-bearing clay. Synonyms in current usage include diatomaceous earth and kieselghur. More antiquated and obsolete terminology includes tripoli-powder, tripolite, and infusorial earth. Worldwide, diatomites occur within Tertiary to Recent lacus- trine and marine sedimentary facies. Although diatomite is wide- spread throughout the world, deposits that contain high purity, commercially versatile ore are uncommon. Physical properties of the diatom and of processed diatomite that provide unique commercial value in a broad spectrum of market end-uses include ornate fine structure, low bulk density, and high porosity and surface area. Properties of equal importance are mild abrasiveness, high absorptive capacity, insulating ability, relative inertness, and high brightness. End-use markets are diverse and range from insulating brick and absorbents through quality sensitive filter aids and premium quality functional fillers. Notwithstanding both the economic attractiveness of the specialty markets and the commercial versatility of the high purity deposits, deposits of lesser purity are mined in nearly all parts of the world for less demanding uses. Mining costs are minimized through open pit quarrying, but in Europe, Asia, Africa, and South America underground mining methods are also employed. Blasting is not required because diatomite is soft and easily broken loose with mechanized equipment. Following gentle crushing, the ore is dried, milled, and processed into one of three broad categories of products: naturally milled, straight calcined, and flux calcined grades. Each of these principal categories is further subdivided into additional grades through particle size adjustment of the powders. Agglomeration of particles, alteration of fine structure, and color change are achieved through calcination. Flux calcination further accentuates these changes. Production throughout the world is dominated by the United States, followed by Romania, the former Soviet republics, and France. Other major producers include Spain, Mexico, Iceland, Korea, Japan, and Germany. Denmark is a major producer of Moler earth products, which consist of a diatomite-clay mixture. HISTORICAL BACKGROUND The first industrial use of diatomite can be traced back some 2000 years to the Greeks and to the use of diatomaceous earth as a component in lightweight building brick and in ceramic pottery. It was not until the mid-1800s, however, that the unique properties of diatomite were first recognized and the market end-uses explored and developed. One of the most important of the early uses followed the development of dynamite by Alfred Nobel in the mid-1860s, whereupon diatomite was used as a component of the explosive to improve stability and safety. Other early uses included low temperature insulating and refractory bricks and as a component in insulating and fireproofing construction panels. During the 1920s, processing technology underwent a very rapid evolution with the development of calcination, flux calcination, and air classification technologies. Through these technologies, innumerable different size and grade classifications could be made for market applications and for rapidly diversified end- uses. Today, the application of processed diatomite for filter aid is the largest of the quality sensitive end-uses. Specific filtration uses include the clarification of beer, wine and liquor, vegetable oil, syrup and sugar, pharmaceuticals, and swimming pool water, to name a few. As a functional filler and extender, processed diatomite is ideally suited for application in paint, rubber, and plastic formulations. Other filler applications include use as an anti-blocking agent in plastic film, anti-caking agent for fertilizer, thermal insulating material, catalyst carrier, polish, abrasive, pesticide and fertilizer carrier, and chromatographic supports. Throughout much of the world diatomite is still used as a component of insulating brick and as an absorbent.

Jan 1, 1994

By Pelin Altinkaya, Maria Leikola, Jussi Liipo, Mika Haapalainen, MARI LUNDSTROM, Eero Kolehmainen

Chloride leaching has many advantages compared with other alternative processes to cyanidation because it has increased metal solubility, improved redox behavior and high leaching rate properties. Also, chlorination is a nontoxic and environmentally friendly process, which is sought by the mining and metallurgy industry. In addition to these advantages, chloride is an effective reagent for the dissolving of metals from refractory ores and process residues that have trace amounts of valuable metals waiting to be valorized. 

By Werner A. Dürrfeld

The Bullflex® System was introduced as a substitute for timber and debris lagging in mines and to create an in-situ early-stage interlocking effect between steel supports and the rock wall. As deplacement and/or disintegration of strata and of rock beds is to be avoided under all circumstances - following the ideas of NATM-steel support can only be loaded to the maximum when point load is avoided and ideal bedding of the rock is maintained.

Jan 1, 1981

By Sukumar Bandopadhyay

A present dominant problem is that of high downtime of the longwall shearer used in the coal production process. The means by which this problem can be overcome are many, but one of, the most important ones is that the-use of an expert system can reduce diagnostic and repair time. In this paper, a fault-diagnostic expert system model is presented. Specifically, the diagnostic architecture of the longwall shearer expert system and its use for diagnostic reasoning are discussed.

Jan 1, 1989

By Martin F. Grier

The Mt Todd Gold Project is located 300km to the south of Darwin in the Northern Territory of Australia. The identified resource comprises 46 million tonnes at 1. 65g/t using a 1. 0g/t cut-off ( 50 million short tonnes at 0.05oz/st). The resource is open to the north and at depth. Mineralisation comprises easterly dipping sheeted quartz/sulphide veins, typically 10 to 20 millimetres in thickness, hosted by hornsfelled greywackes. The majority of the ore body is primary ore with only 10% classified as oxide ore. Early testwork showed that the ore was not suitable for heap leaching, giving only 50% recovery at a -3mm crush size. Acceptable recoveries were obtained at a P80 of 75 micron. However, the ore is extremely hard.

Jan 1, 1992

By R. J. Rice, K. F. Denning

Effect of iron on the removal of arsenic, mercury and selenium from gold mining effluents. Arsenic, mercury and selenium are common trace elements in gold tailing effluents that require removal before the water is either recycled or returned to a receiving body. One of the better methods of removal of these elements is the use of iron salts whereby, the metal is trapped on the freshly precipitated hydrolyzed iron oxides either by adsorption or enmeshment of the fine particulate and hence, removed from solution. The metal removal is effected by iron to metal ratio, pH, temperature etc. Pilot plant tests have shown that mercury can be reduced to < 5 ppb Hg, while full scale tests on arsenic and selenium have achieved levels of < 50 ppb As and < 10 ppb Se in well controlled systems.

Jan 1, 1993

By P. van der Veen

There are two key reasons for this presentation: - Sustainability - Improving the economic, environmental and social impact of mining. As I will discuss in my presentation we see sustainability throughout the mine life cycle as critical for successful mine development - that is the mine makes a successful contribution to economic development and poverty alleviation for the host community and host country and at the same time the mine is a successful investment for the investor. - Knowledge Sharing ? The World Bank is not only a development bank, but also a ?knowledge bank?. One of our key functions is the dissemination of usable information and knowledge. We are here not only to share our experience but to learn from your experience as well ? two reasons that fit clearly with the mandate of the World Bank Group.

Jan 1, 2003

By D. E. Ranta, M. G. Schulz

Mining of Molybdenum at Questa, New Mexico has been accomplished by block cave methods since August, 1983. As caving progresses, a periodic geologic evaluation is made of the rock types present in finger raises on the Grizzly Level of the mine. The production maturity of the cave can be monitored by relating this data to geologic cross-sections through the orebody. The draw point mapping program is a simple and effective tool that is used in making draw control decisions at Questa.

Jan 1, 1992

By Lee W. Saperstein

The SME Research Council assists SME and its constituencies in establishing research directions that will benefit the mining industry and its professions. It also provides information about these directions to its membership, to government and to related industrial societies. The 1995 Research Forum, organized and chaired by George Luxbacher, was the second in a series of meetings organized to develop these directions. A copy of the full proceedings is available from SME for $12 plus postage and handling. The first research forum (Saperstein, L., 1993, "Technology for the Future, MINING ENGINEERING, Vol. 45, No 11, November, pp. 1382-85) invited mining industry representatives to discuss the unsolved technical problems that were keeping the industry from greater economic and environmental efficiency. The second forum asked academic researchers to discuss the same general topics from their perspective. It came as no surprise that, in general, the two sets of presenters tackled the same problems. There was no surprise when the academics spoke of the need for fundamental long-term research. What may have been surprising was the number of university people who spoke for near-term research that leads to measurable economic returns or savings. The closure of the US Bureau of Mines (USBM) has changed the objectives and attitudes of the SME Research Council. From being a point of liaison between SME and USBM - a conduit of items from each party to the other the council is now much more on its own. This isolation presents opportunities and hazards. The opportunities are exciting because the council could be the focus for mineral industry research policy if it were properly structured. The hazard is obvious - if there is no bureau, it could be argued, why maintain the council? Many people believe that SME should take the first course and become the beacon for research policy. More than ever, money is being spent on minerals industry research by the federal and state governments - particularly at the mineral-oriented land-grant universities - by industry and by consortia among these groups. SME could be at the hub of these programs. There is a general concern that industry is less able to maintain an economic edge by means of geologic discovery. According to Titley, there will be fewer major, new world-class discoveries except, possibly, at the continental and tectonic-plate margins. Consequently, economic advantage will go to those companies and nations that stay ahead technologically. Given the inevitable diffusion of technology, it can be concluded that technology development, underpinned by research, must be continuous to maintain profits. This is a change from earlier years when change would occur in relatively rare major steps that were interspersed with extended periods of technological equilibrium. Over the fiscal years 1994 to 1997, there has been a 24% cut in research spending by the Department of the Interior (figures from the American Association for the Advancement of Science). This is the largest budgeted percentage cut in research funding of any federal department. Even so, there is still a substantial amount of federal research funding expended in the mineral and extractive-energy industries. The US Geological Survey, Environmental Protection Agency, Departments of Defense and Energy and others expend substantial funds on minerals industry research. Industry - producers and manufacturers - is also spending large sums on research and research-like activities. This activity argues that there is a role for SME&apos;s Research Council. Providing focus Consortia. The closure of USBM has resulted in the migration of expertise to consulting firms and to other entreprenrutisl research entities. Many of these groups are creating ad hoc consortia among themselves, nearby universities and industrial partners. The Research Council is well placed to provide an open forum for these con¬sortia. Presentations of research results, as went on in the annual meetings of the Generic Mineral Technology Centers, can help to establish an. archive of results and an avoidance of duplication of research. A continuing sense of research directions can evolve. National Science Foundation. No discussion of consortia would be complete without mention. of the National Science Foundation&apos;s (NSF) programs for Industry/University Cooperative Research Centers (IUCRC) and Grant Opportunities for Academic Liaison with Industry (GOALI). NSF is aware of the gap in federal support of science and technology caused by USBM&apos;s closure.

Jan 1, 1997

By James I. Mathis

Should an arbitrary reduction factor be applied to laboratory compressive strengths when designing pillars? The answer is, as is the main contention of Peng&apos;s article, probably not. Many factors affect the strength of the material remaining in the pillar. On the other hand, outside influences will influence the strength testing results from the lab. This is not the first article, nor the last, to discuss the discrepancy between the two strengths. As was discussed in the article, actual pillar strength is affected by several factors. The two mentioned were: • The scale effect of discontinuities. How large must the pillar be so that the increase in discontinuity count with size will not decrease the strength. • Non-uniform strengths and lithologic units within the pillar. The scale effect of discontinuities is important. What size block must be tested so that the rock mass strength is actually measured? For a highly fractured rock mass, or coal with a high cleat density, this sample may be quite small. Conversely, if an unaltered, moderately jointed, quartz monzonite was examined, the sample block would likely be very large. This is the subject of ongo¬ing research. More to the point, if the tested sample is sufficiently large to model the rock mass strength, then no reductions should be made in the lab strength based on this factor alone. Non-uniform strengths and variations in lithologic units will also affect the pillar strength. I am not an expert in coal mines, having gained my experience in hard rock metal mining. These problems, though, are commonplace. However, strength sampling for pillar strength determination involves sampling material from within the lithologic unit that will form the pillar, not from pieces of material found on the floor. In addition, this sampling should cover the entire range of strengths of the material in the pillar-hard units (such as the partings described by Peng), as well as soft units. Testing results should then be included in the pillar design. Contrary to statements in Peng&apos;s article, at least one rock mass rating system (Laubscher, 1990) allows for the compositing of strong and weak units into a design rock mass strength that can be used for pillar design.

Jan 1, 1993

By John A. Lombardi

The HW Process Technologies Engineered Membrane Separation (EMS"') technology is a patented system for the removal of multivalent base metal cyanide complexes from cyanide process streams, and EMSni permeate, concentrate and recovery terminology is explained. Specifically, use of the EMS™ system for the removal of Cu(CN)i- and Cu(CN)43- cop­per from cyanide process streams is discussed. The historical "Copper-Gold" processing paradigm of copper related cyanide consumption and complexation and methods to recover copper and copper complexed cyanide from Cu-Au process solutions are summarized. An advanced stage R&D sequential Cu-Au leaching circuit is proposed wherein two PLS streams are generated, i.e., a high copper tenor "first flush" Cu-PLS and low Cu tenor "second flush" Au-PLS. Copper and cyanide recovery from the EMS"' concentrate generated by Cu-PLS EMSTI,f processing by well known acidification processes and lesser developed, but techni­cally feasible, electrowinning processes are projected to be lower cost than similar dilute solution treatments. Gold is described as Merrill-Crowe plant recoverable from the EMS™ permeate stream coming from the Cu-PLS EMS"' process. Gold is also recovered from the EMSTI,f permeate generated by the processing of an Au-PLS bleedstream. The economics of the proposed Cu-Au-EMS"' circuits are estimated as $2/ gpd capital cost for large systems and $1- $3/ l 000 gallons treated operating cost plus royalty.

Jan 1, 1998

By L. Adler

Determining whether a railroad locomotive will skid under varying conditions is a fairly routine, pervasive problem. However, some of the equations provided are wrong, others are at best murky. All require correction or clarification. Skidding during heavy braking is a crucial safety problem, possibly resulting in loss of control and collision. It can also be an economic detriment, ruining wheels and tracks and, by inhibiting acceleration, causing reduced full-speed times. While skidding is less likely for rubber-tired equipment, a comparable problem exists for tractor-trailers operating on poor surfaces. The primary reference is to the SME Mining Engineering Handbook (pp. 14-11, Eqs. 7 and 8), which is taken as authoritative and normative (Brantner, 1973). Fundamentally, the physical weight of the locomotive can never be negative (-). However, based on this reference it can be negative on adverse grades, during braking (Eq. 7), and on favorable grades, whether accelerating or braking (Eq. 8). Additionally, it should be noted that the term rW should be Rw. To avoid having the locomotive weight turn out negative, "absolute value" brackets must enclose the right-hand expression of both equations. Also, the weight of locomotive can be greater than the right-hand side value introducing the common "greater than or equal to" symbol (>_). While these alterations are easy to make, the use of the algebraic sign associated with each term is still confusing, as

Jan 1, 1991

By Ivor Hawkes, Malcolm Mellor

INTRODUCTION There are currently around fifteen companies in the United States and Europe manufacturing hard rock tunneling machines. In recent years upwards of 200 hard rock tunnels of lengths up to 12 miles and diameters to the order of 30 ft have and are being successfully driven by over 100 different machines. It has been predicted that within the next decade over 2,000 miles of tunnels will be driven for transportation purposes in the United States alone (OECD Advisory Conference on Tunneling, Washington, 1970) and it is expected that eventually most tunnels including mine drivages will be excavated by machines. All tunneling machines have certain common basic functions; thrust is applied to drive or hold the rock cutting tools into the face, and torque is applied to rotate the cutting tools over the face so that they can continuously break out rock. The speed of head rotation, together with the torque requirement, determines the cutter head power. (The power required to push the head forward is usually negligible.) There are many factors which determine how successfully a given tunneling machine will perform in a given rock but one of the most important is effective utilization of cutter head power. This paper is a review of the specifications and performance of hard rock tunneling machines, obtained from manufacturers&apos; catalogs, published literature, talks with manufacturers and visits to operating machines throughout the United States and Europe.

Jan 1, 1997

By H. Douglas Dahl

In order to provide a reference framework for discussing the applicability of drilling technology to shaft construction in coal mining ventures, it is meaningful to review the history and nature of United States coal mines relative to shafting. Coal mining in the United States is characterized by shallow depths relative to most of the coal mining world. While the trend is toward deeper and deeper mines, many new mines have shaft depth less than 800 feet, and a large number of operating mines are drift or outcrop mines utilizing shafts for ventilation and portals. In the past, shafts of 200-300 feet have been commonly constructed. The use of conventionally sunk shafts at present and in the past is due in part to the shallow shaft length required, favoring conventionally sunk shafts. Another factor is that large shafts are required for multipurpose and production shafts. A third has been the practice of utilizing shaft construction contractors who had been until recently very competitive with raise drilled shafts at shallow to moderate depths. Recently, however, the costs of conventionally sunk shafts have skyrocketed. Too, more shafts are being required. Several factors are responsible among which are: (1) The increasing depth of shaft required for new mines and for shafts in advance of old mines. This significantly affects unit costs, e.g. $/yd3,of conventionally sunk shafts. Moreover, more gas is encountered in the shaft sinking operation.

Jan 1, 1976