Search Documents

By E. C. Ekedahl, R. J. Heath

Introduction Potassium, together with nitrogen and phosphorous, is an essential nutrient required for growth. Since all living things need potash, the major demand for potash - about 95% of the total - is as a fertilizer. Agricultural productivity has increased dramatically in recent times. This increase in crop yields requires substantial amounts of added nutrients to keep the soil fertile. It follows then that potash will always be in demand. There is no substitute. Other fertilizers that contain phosphorous (P) and nitrogen (N) are complementary and not competing products. Fireplace ashes (pot-ashes) have a relatively high potassium content. Their value as a fertilizer had been recognized for centuries. But today's potash industry did not begin until deposits of potassium-rich ore were discovered and exploited in Europe during the 19th century. Canadian potash development Potash in Saskatchewan was first recognized in 1943. It was discovered as a byproduct of an oil exploration program. But it was several years later before the existence of a major commercial deposit was acknowledged, and not until 1951 that the first attempt at development occurred. That attempt was unsuccessful. The shaft flooded and was abandoned. It did, however, demonstrate the need for new technology to penetrate the waterlogged Blairmore layer. This was eventually developed and the first mines were brought into production in the early 1960s. Once the technology was available, and the extent and quality of the potash beds became known, a number of companies proceeded to develop mines. By 1970, seven mines were in operation and three more were nearing completion. Combined, total capacity then was 7.6 Mt/a (8.4 mil¬lion stpy) K20. At that time, world potash consumption was about 15 Mt/a (16.5 million stpy). This increase in supply from Canada produced a large potential surplus that shattered the prevailing balance between supply and demand. Although world demand increased steadily throughout the 1960s and early 1970s, it was several years before world supply and demand were again in balance. Saskatchewan capacity has been expanded a number of times. It now stands at 10.7 Mt/a (11.7 million stpy) K20. Actual production has not approached this figure, however. Two new mines in New Brunswick have recently been built with a combined annual capacity of 1.2 Mt (1.3 million st) K20. Total Canadian capacity of about 12 Mt/a (13 million stpy) now amounts to 30% of world capacity. Central offshore marketing organization Canadian Potash Exports Ltd. (Canpotex) was created in 1970 as the offshore marketing organization for Canadian producers. Canpotex is owned by Saskatchewan producers and is their exclusive marketing organization for offshore business. Each company handles its own sales in Canada and the US, but all sales to other markets are handled through and by Canpotex. The Saskatchewan industry has an ore body of a size and consistency unmatched anywhere in the world. Large efficient mines have production costs that compare favorably with other producing countries. On the minus side, Saskatchewan is remote from most major markets. It therefore needs the ef¬ficiencies that stem from one organization that coordinates all offshore shipments and minimizes distribution costs. Agriculture guides potash market In the period following World War II, potash was a classic growth industry. World demand increased each year from 1945 to early 1970s. Since then, demand has been more erratic. Some years show substantial increases, but are followed by significant declines. For about the last decade, the pattern has been unclear and future demand has become correspondingly difficult to predict. North America and Europe together account for about 40% of the world potash consumption. In both areas, farming is characterized by surplus production, declining crop prices, and expensive government support programs. Under those circumstances, farmers respond by minimizing input costs. Fertilizer is one of the items they reduce. Potash is retained in the soil. It is possible to reduce potash application with no immediate deterioration in crop yield. The lower yields occur only when potash levels are depleted. So, farmers can econo-

Jan 12, 1987

By N. D. Jagger, I. M. Arbuthnot

Introduction Over the last five years, a large number of small- to medium-sized carbon-in-pulp treatment plants have been built in Australia, most designed to treat between 250,000 t/a and 1.5 Mt/a of ore. Because of the limited capital resources and tight cash-flow positions of these relatively small mining companies, the primary requirement was often to get a plant built and operating in a short period of time and at minimal capital cost. Therefore, since the inclusion of both pre-leach and tailings thickeners represents an obvious and significant capital cost, most of these plants were built without thickeners or even detailed, cost-benefit analyses on their inclusion. In some cases, the increasing use of High Rate Thickeners (HRTs) in the mineral processing industries has, however, resulted in a reassessment, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas where borefields are costly to install and water is limited. With the startup and operation of these installations, the resulting significant savings in cyanide consumption has been recognized, in many situations, as a primary justification for the installation of HRTs. Solution balances Degradation of cyanide occurs in the tailings water discharge to slime dams. The degree of degradation (cyanide loss) in the water recovered depends on a number of factors, but it is usually assumed to be about 90%. The most important mechanisms of CN loss are through HCN losses and oxidation by oxygen in the air, which also assists in the hydrolysis of CN. These mechanisms are supported by the large dam surface area and the long retention time of the tailings water in the dam. By thickening the CIP tailings at the plant and recovering as much tailings water as immediately possible, these losses are avoided. The retention time in an HRT is less than three hours, and the surface area is relatively small. Therefore, CN losses are negligible, which is not necessarily the case in conventionally-sized thickeners. Fig. I shows a block diagram of a 100-t/h gold plant without a thickener. In this example, 50% of the tailings water pumped to the tailings dam is recovered, and the CN concentration of the returned water is 10% of the tailings CN concentration of 150 ppm. Fig. 2 represents a plant with an HRT on tailings, thickening to 55% w/w solids. In this case, the thickened tailings are pumped to the dam, and 25% of the contained water is recovered. The recovered water and the mill make-up water are not sent directly to the mill; instead, they are added to the thickener feed and mixed with it prior to thickening. By doing this, the tailings are effectively washed, and the additional cyanide is recovered. Solution balances over these two circuits show cyanide recoveries of 5% and 65%, respectively. Thus, the thickener use increases cyanide recovery by 60%. Fig. 3 shows a two-stage HRT circuit in a countercurrent decantation (CCD) configuration. In this example, an additional 13% of cyanide is recovered through the use of the second-stage unit. This configuration can be justified when residual cyanide levels are high. Capital and operating costs - Case study 1 Illustrative cost figures are based on a CIP tailings thickener installed, in early 1988, as part of Dominion Mining's treatment plant at Paddy's Flat near Meekatharra. (All costs within this paper, unless stated otherwise, are in Australian dollars.) [Assumptions: Feed rate 150 t/h Ore moisture content 5% Leach density 40% solids Underflow density 55% solids Residual cyanide in tailings 150 g/m3 Flocculant dosage 15 g/t Consumable costs: Water $ 0.40/m3 Cyanide$ 2.00/kg Flocculant$ 4.50/kg Power$ 0.12/kWh Length of tailings pipeline2,500 m Capital costs of the major items involved in the thickener installation are given below: Thickener unit, 15-m diam $ 230,000 Water return pumps 12,000 Water recirculation pumps 28,000 Feed box 5,000 Flocculant make-up system 18,000 Flocculant storage tank and dosing pumps 11,000 Piping and valves 85,000 Electrics and instruments 47,000 Civil works 29,000 Installation 69,000 Total cost$ 534,000] Savings in capital costs that can be attributed to the

Jan 1, 1993

By Robert F. Goss

OCAW appreciates the opportunity given to us by the sponsors of this Conference to present our position and policies on the issue of radiation hazards in mining. Our principal concern is the health impact that the mining of uranium has on our members. OCAW represents 1,500 underground uranium miners and more than 10,000 underground miners with 3,000 in the Rocky Mountain region. The U.S. Public Health Service has determined through mortality studies that the number one cause of death among uranium miners is lung cancer. It was also determined that exposure to radon daughters and mine dust correlates with the lung cancer experience of uranium miners. Data from the U.S. Mine Safety and Health Administration has also shown that not only uranium underground miners, but all underground miners, are exposed to radon daughters -- especially underground miners in the Rocky Mountain region. It is our position that any OCAW underground miner is at potential lung cancer risk. The dosages of radon daughters that our miners are exposed to are very many times the background levels of radon exposures in the communities where they live. We are also aware that cigarette smoking accelerates the onset of lung cancer; however, it has to be clear that the available scientific evidence shows that alpha radiation does initiate lung cancer and that cigarette smoke, as a recognized co-carcinogen, promotes cancer already initiated by radiation. It is true that cigarette smoke increases the risk of cancer significantly for miners exposed to radon, but nonsmoking miners have experienced lung cancer rates twice as high as the comparable members of the U.S. population. OCAW's position is that the occupational regulatory agencies should concentrate on the exposures that can be controlled; that is, occupational exposures rather than life-style exposures. Our Union has maintained a consistent posture in relation to carcinogens in the workplace -- that is, exposure to cancer-causing agents should be limited to the [lowest feasible level]. OCAW has interpreted lowest feasible level as the lower limit of detection of the collection and analytical method used to detect the carcinogen. Our posture is based on the available scientific information on carcinogenesis. We have asked the scientific community, many times, to provide us with safe levels of exposure to carcinogenic substances, including radon daughters. The answer has been: "We cannot determine levels of exposure low enough to assure that no cancer will occur." In short, there is not a "safe threshold" for any carcinogen. This statement does not come from one of the few so-called "pro-labor scientists," it comes from the National Cancer Institute and the National Institute for Occupational Safety and Health. I don't need to be a scientific sage, then, to conclude that the lowest level of exposure corresponds to the lowest risk of developing cancer. That is, then, our policy on exposure to carcinogens. It seems there has been an attempt to ignore the fact that lung cancer in uranium miners is the principal cause of death. Uranium miners are no exception from workers exposed to carcinogens. Our policy applies to them. Uranium miners should be exposed to the lowest feasible level of radon daughters and any decrease in the permissible exposure level is a decrease in their lung cancer risk. Accordingly, OCAW has petitioned the Department of Labor for a new permissible exposure limit to radon daughters in uranium mining, which lowers the current exposure standard from 4 Working Level Months (WLM) per year to 0.7 Working Level Months per year. We made our demand to the Department of Labor on April 20, 1980. We are still awaiting action from the Federal Government on our petition. OCAW is also very concerned with other important health impacts of uranium mining. We are concerned with a rate of disabling accidents and fatalities which is twice as high as the same rate in other underground mines, excluding coal. We are also concerned with the rate of respiratory disease fatalities among uranium miners which is almost four times the rate among a comparable U.S. population. We have expressed those concerns when the U.S. Senate proposed a Federal Compensation Act for uranium miners. That proposal, by Senator Dominici of New Mexico, found a quiet death in two Congressional sessions. In conclusion, our position on lung cancer induced by radon daughters is the same position we have taken with all other industrial carcinogens: The lower the exposure, the lower the risk. OCAW is demanding a drastic decrease of the permissible exposure limits. OCAW will never accept that a segment of our membership which mines uranium should take the lion's share of the risk while the uranium mining companies take all the benefits.

Jan 1, 1981

By C. J. Dungey

INTRODUCTION The County of Cornwall is situated in the South Western extremity of England, see Fig. 1, and has for hundreds of years been an historical centre of mining activity. In the last century many thousands of Cornish miners emigrated to Canada, U.S.A., Australia and numerous other countries throughout the world to form the nucleii of mining industries in those lands. At present there are four active underground mines within the county, all mining tin, together with a relatively large china clay industry. All the operations are directly or indirectly associated with the three main granite intrusions, namely the Land's End Granite, the Carnmenellis Granite and the Bodmin Moor Granite. The report which follows relates to two mines, owned by the South Crafty Group of Companies, namely the South Crofty Mine itself and its smaller subsidiary, Wheal Pendarves. Both these mines are adjacent to the Carn Brea Granite ridge, see Fig. 2, which is an off-shoot of the main Carnmenellis Granite mass. The Carn Brea Granite has provided one of the most intensive areas of copper and tin mineralisation anywhere in the world. Many of the mines worked during the last two centuries and the early part of this century were situated close to the metamorphic aureole surrounding the granite intrusion. Both South Crofty and Wheal Pendarves have their shafts collared in the overlying slate, locally known as killas, but the major part of their workings are in the granite beneath. The ore bodies, or lodes, of both mines are generally steeply dipping and approximately one to four metres in width. They have been, and continue to be, worked by either back or under-hand stoping with the major level interval being approximately 37 metres. A feature of both stoping systems is that they require no back filling and in many cases the completed working areas have remained open for many years due to the competent wall rock conditions. The stoping operation necessitates having box-holes or draw points at regular intervals along the strike length at 4 to 7 metres centres; thus a stope some 50 metres long may typically have ten box-holes or draw points through which air can percolate into the empty stopes above. The granite country rock contains traces of uranium minerals, namely pitchblende or uraninite, and it is the decay of this uranium mineral which leads to the formation of the mobile radon gas which, together with its short lived daughters, may create a hazard. The presence of uranium minerals has long been known, but the quantities being so minute, it was not appreciated until some ten to fifteen years ago that these might present a hazard. The Mines and Quarries Inspectorate approached Management approximately ten years ago with a view to taking samples in areas of the mine that they felt might contain the highest concentrations of radon. Samples were thus taken in several areas of both mines, normally well away from working areas and where there was no through ventilation. The results of these initial tests were published by the National Radiological Protection Board in a paper entitled "Radon and Its Daughters in Various British Mines". The results of the initial surveys made it apparent that improved ventilation was the most important factor in reducing radon daughter concentrations within the mine atmosphere, with increased flow rates having three beneficial functions, viz. (1) To dilute radon daughter concentrations. (2) To prevent radon and its daughters reaching a state of equilibrium. It is not uncommon for radon and its daughters to have a disequilibrium factor of 1,000 in some uranium mines.

Jan 1, 1981

By Duane A. Smith

Horace Tabor. No 19th century Colorado mining man is better known but, unfortunately, probably less understood. He is little appreciated for his significant contributions to the industry and the state. A century ago, Tabor was headline news. The legend today, however, has become so all pervasive and so interwoven with fact that the two are hard to separate. For example, he never told Baby Doe on his death bed to hang on to the Matchless mine. Yet this has emerged as staple Tabor fare. So much attention has been focused on his matrimonial triangle that it overshadows the man. Symbol of mining's reward Tabor traveled west in the 1859 Pike's Peak gold rush. In the next generation, he came to symbolize the rewards mining might lavish on an individual. The Leadville Daily Herald (Sept. 10, 1882) could write, without exaggeration, that "the extent which the mining industry of Colorado is under obligation to Tabor cannot be easily estimated - what he has done for Leadville and Denver is patent to all." It had not come easily, nor had Tabor started out a success. His early placer mining at Payne's Bar, near present-day Idaho Springs, CO, had turned no fortune. So in 1860, he, his wife Augusta, and son went south to Colorado City, then over Ute Pass and up the Arkansas Valley to Oro City. Arriving soon after the initial discovery, Tabor staked a good claim. With a sharp eye, he and Augusta broadened their base by establishing a store. Both mining and business would pay dividends in the following years. By the season's end, though, Oro City was already declining. Always on the lookout for a richer district, Tabor and his family moved the next year across the mountains to promising Buckskin Joe. The familiar pattern followed, with the store and post office being the center of their attention. Mining investment and management now replaced the earlier physical panning and sluice operating. Seven years later, the Tabors abandoned Buckskin Joe and returned to Oro City. It had moved up California Gulch to be near the district's best mine, the Printer Boy. Middle class was not enough Middle class respectability, plus a steady income, was the Tabor's by the 1870s; fine as far as it went. But it proved far from the fortune Horace had always been seeking. Oro City languished in the backwash of Colorado mining and Tabor seemed like many men who had drifted around the Territory following the ebb and flow of mining. His faithful wife Augusta had been a steady factor in the success the family achieved. She helped year after year to operate the store and post office. Not simply the happy-go-lucky individual he has often been portrayed, Tabor was a hard working businessman/mine owner. An R. G. Dun and Company agent evaluated him in 1876 "Net worth $23,200. Is a very shrewd businessman and not liable to lose money, has a good chance to make money as he had no competition." Leadville: Tabor's silverlined-fortune After all those years on the Colorado mining frontier, in 1877, Lake County's wealthiest and most respected merchant made another move. It was short in distance, only 4 km (2.5 miles) down California Gulch, then a little north to a new mining camp. This new camp, soon named Leadville, gave birth to the Tabor fortune and legend. Middle-aged (Horace was 47), the Tabors once more set up their general store and found themselves in the midst of the open¬ing of a new district. This time silver beckoned and not the gold that had brought them West 18 years before.

Jan 1, 1989

By Waclaw Trutwin

The idea of automatic or remote control of the mine ventilation process generally, and methane concentration particularly, attracts the attention of mining engineers more and more. The advantages of introducing mine ventilation control systems are breaking traditional reluctance. The change of attitude is not only because of the requirements of modern exploitation technology, but it is also due to the recent progress in development and successful introduction of reliable monitoring systems and actuators in the form of controlled ventilators and doors [1]; [2], [3], [4], [5], [6]. Many 'years of theoretical and experimental studies of the dynamics of mine ventilation processes created the needed base for a proper design of an automatic control system [7],[8],[9], [10]. From these studies must, however, be drawn a fundamental conclusion, which may be regarded as the motto of this paper: An automatic control system for mine ventilation ill-conditioned or improperly designed is capable of creating hazard situations in response to random disturbances, much more, severe in consequence than a traditional ventilation system without any automatic or remote control! This statement is easy to prove if the dynamic properties of the ventilation process are taken into consideration. The ventilation process, as a matter of fact, is described by non-linear equations, and it must be expected that the process has more than one state of equilibrium. In other words, in the ventilation process may exist not only one but also more than one steady-states of flow, of which some are stable and others unstable. In certain circumstances, there may be no steady-state at all, and the process will oscillate [8], [11] , [12] . The state of flow in a network tends towards a steady-state and the actual steady-state established will depend on the initial conditions or disturbances in flow (fire,. etc.), which steady-state from the total number that will be . We frequently observe jumps from one steady-state to another. Disturbances in flow conditions which may cause such transitions are events of random character, occurring very rarely. Concluding, it must be stressed that there has to be a control system adjusted to the ventilation process in order to avoid situations mentioned above. There is only one alternative available and suitable for examination or study of the dynamics of a given mine ventilation problem: either by continuous monitoring of the real process, or numerical simulation of the process using a mathematical model. The advantages of the second method are obvious. This method allows consideration of every possible case very quickly and cheaply in relation to the first method. The aim of the paper is to show again that the simulation of the mine ventilation process and particularly a methane concentration process, separately or combined together with a control system, are real possibilities. A simulation method requires precise specification of the problem under consideration. For example, if we intend to examine a methane-concentration control system, the following items have to be specified: - expected target function of the control system. - structure of the control system. - mathematical model of control system, including sensor system, data preparation system, controllers, decision routine, regulators, etc. - structure of mine ventilation network. - mathematical model of ventilation process, including air flow and methane concentration processes. - pattern of disturbances which may occur in the controlled process as well as initial conditions on a 'start-up' of the system. Using typical computer programs for numerical solution of equations in the mathematical model of the problem involved, we are able, within the adequacy of the model, to simulate every case specified by the disturbances and initial conditions. As a result of simulation, it is expected that the following parameters could be defined: - transient flow in the network. - transient state of methane concentration in working areas. - stability of flow and methane concent¬ration. - stability of the control system. - range of control. - efficiency of control, etc. It is obvious that simulation methods readily allow for modifications to existing systems such that desired results will be obtained. Also optimisation problems could be solved by use of the simulation methods. In order to illustrate these general thoughts, a brief presentation of a mathematical model of methane concentration and

Jan 1, 1980

By G. T. Newell, J. G. Stone, V. M. Mejia

Introduction Advances in drilling have reached a point where large diameter cores can be recovered from "tight," or weakly indurated placer gravels. In such ground, core drilling can provide more reliable data regarding tenor than can be obtained using churn drilling or similar classical techniques. It can also provide metallurgical and geological information that is not available from samples obtained through alternate methods. In 1985, Coastal Mining Co, a subsidiary of M. A. Hanna, and Western Gold Reserves began to review a Tertiary placer deposit owned by San Juan Gold at North Columbia, CA, about 14 km (9 miles) northeast of Grass Valley. The deposit is one of the largest remaining unmined portions of the formerly extensive early Tertiary ancestral Yuba river system. It has been known since the 1850s, has been the subject of much technical literature, and has been the object of at least four previous drilling programs. The eastern one-third of the 6 km (3.7 mile) stretch of the channel between North Columbia and Badger Hill was partially stripped by large scale hydraulic mining in the late 1870s and early 1880s. Mining ceased in 1884 when the Sawyer Decision prohibited further discharge of hydraulic tailings into the Sacramento and San Joaquin Rivers. By that time, about 30 to 45 m (100 to 150 ft) of relatively low grade upper gravels had been removed over some 81 hm2 (200 acres). About 90 to 105 m (300 to 350 ft) of higher grade middle and lower gravels were left at least partially stripped. In 1914, a few churn holes were drilled along a widely-spaced line. In 1938-1939, Selection Trust conducted an extensive drilling campaign to evaluate the deposit. Particular attention was directed toward the partially stripped eastern portion. In 1968, the US Geological Survey drilled three churn holes in the eastern part of the deposit. The US Bureau of Mines conducted experimental mining and drilling in the Badger Hill area. In the late 1970s, Placer Service Corp. acquired a lease on the deposit. Between 1979 and 1984, Placer Service drilled 28 large diameter BADE (a German-manufactured machine) drill holes on the eastern portion of the deposit. The surviving records from the widely-spaced 1914 drilling program are fragmentary and the reported grade not well substantiated. The 1968 holes were drilled for scientific purposes. Again, drilling details are not available. However, detailed records for both the churn drilling program and the BADE program were available and formed the basis for the initial evaluation of the property. Geology The geology of the auriferous Tertiary gravels of California have been described by Whitney (1880), Lingren (1911), and, more recently, Yeend (1974). In general, the Tertiary gravels in the North Columbia area occupy a broad channel cut into pre-Tertiary igneous and metamorphic rocks. The upper, or white gravel is overlain conformably by volcanic tuffs and volcaniclastic rocks. A middle gravel is characterized by the presence of silicified and carbonized wood. A lower blue gravel unit has relatively coarser cobbles and contains a higher proportion of igneous and metamorphic cobbles than the other units. The upper gravel consists of interbedded pebbly sand and silty, or clayey sands with prominent cross bedding. Most of the pebbles are well rounded and consist mostly of white vein quartz and quartzite. The upper unit is moderately well compacted. Exposures in the walls of the old hydraulic mine pits stand at 45° and 50° angles. The gold content of the unit is well below an economic cutoff. The middle gravel - included with the upper unit by Yeend (1974) - is coarser grained, with carbonized wood, and 75 to 100 mm (3 to 4 in.) cobbles of metased-imentary and metavolcanic rocks in a sandy matrix containing abundant lithic fragments. The upper contact appears to be conformable, but the lower portion of the unit appears in places to consist of reworked lower gravels. The unit contains less clay than the upper unit and is somewhat more friable than the underlying lower gravels. The gold content, while somewhat higher than the upper level, is too low to be of ore grade. The lower gravel averages between 30 to 45 m (100 to 150 ft)

Jan 9, 1988

By S. Budirsky

J.B. Gwiazda's article deals with an interesting problem that has not been studied thoroughly up to now. Gwiazda has proposed a technical solution that eliminates horizontal load imposed by the supports on the roof. That load is due to a discrepancy between the trajectories of the canopy and the overlying strata. It is true that the improved lemniscate guidance system proposed by Gwiazda could eliminate the horizontal load but, on the other hand, it would represent a higher cost of the supports, and it would complicate the already complicated mechanism of powered supports. That is why we must be convinced that the proposed improvement is actually needed. From that point of view, the following questions should be elucidated. As shown in Fig. 1, the point O travels along the curve a, which produces horizontal load on the roof in the direction of the coal face. As stated by Gwiazda, "such a high load is capable of destroying the roof above the support, causing rock debris to be scattered around the face." The results of our measurements carried out in coal mines of the Czechoslovak part of the Upper Silesian Coal Basin show that the convergence in the modern type of powered supports does not exceed several millimeters (not more than 10) per hour. Similar conclusions were drawn from field measurements performed in the Polish part of the Upper Silesian Coal Basin (see S. Romanowicz and H. Szopka in Proceedings, Scientific and Technical Symposium Simmex '85, Katowice, Poland, pp. 73 -83). The small vertical closure of the supports also induces a small horizontal displacement of the canopy. In addition to this, the transmission of forces between the roof and the canopy is influenced by the layer of debris on it, i.e., the canopy slides without imposing a greater horizontal load on the roof. This was deduced from field measurements of Voest-Alpine F 4/4600 powered supports equipped with rams instead of the common front lemniscate links (denoted as 1 in Fig. 5). In these supports, the pressurizing of the space of piston rod (la in Fig. 5) causes the rams to close, which induces horizontal load on the roof in a direction toward the coal face. After the setting of a support unit, the pressure in the piston rod space was found to drop, frequently to zero, because the small horizontal sliding between the canopy and the debris or inside the debris caused the horizontal reaction from the roof to fall to zero, although the debris were pressurized by vertical setting load. As a consequence, there was no horizontal load imposed by the canopy on the roof. A rise of the horizontal load was recorded only after the passage of the shearer and during lowering of the adjacent units. Thorough information on the results of the afore- mentioned field measurement is given in the paper, "Analysis of the performance of shield powered supports installed in a thick seam," published in Mechanizacja i automatyzacja gornictwa, 1982, No. 12, pp. 38-46. An English translation of the paper is available from the author. We have deduced from our observations that horizontal load imposed by the canopy on the roof in the direction toward the coal face is useful for roof control because it limits the displacement of the immediate roof toward the gob particularly during the rise working. We came to the conclusion that horizontal load on the roof toward the coal face should be induced on purpose. Could Mr. Gwiazda prove with the results of field measurements his contrary opinion? Has the small horizontal displacement of the canopy toward the face actually had an adverse effect on the roof? As shown in Fig. 2, during the setting of a support unit, the canopy imposes a horizontal load on the roof in the direction of the gob. In this case, I share Gwiazda's opinion that the horizontal load could have an adverse effect on the roof. Nevertheless, two important circumstances were neglected - the horizontal compliance of the supports and the interaction of adjacent units. The question of the compliance was analyzed precisely by I. Krumnacker in Gluckauf -Forschungshefle, 1984, NO. 5, pp. 219-223. He found that due to the clearance between the hinge pins and the eyes of the sheild and due to the elasticity of the steel structure,

Jan 1, 1988

By Robert W. Miller, Rhoda S. Kriesel

INTRODUCTION With each passing year, the general public becomes increasingly aware of the potential hazards associated with many products and services previously considered unharmful. This new consciousness is especially evident in the workplace, both as the result of advances in scientific understanding and the influx of concerned, responsible professionals into the labor movement. For example, data produced by epidemiologists doing retrospective mortality studies which related mortality to toxic substance exposures has often been the prime motivating factor behind reductions in exposure standards. This certainly has been the historical case with many radiation exposure standards, including the limitations set for "Working Level" exposure. The concept of "Working Level" was introduced in PHS Publication No. 494 as a result of both the difficulty in relating radiation units to biological effects and the complexity of interaction of radon daughters with the physical environment. WORKING LEVEL One working level is defined as any combination of radon daughters in one liter of air that will alternately release 1.7 x 105 MEV of alpha energy during decay of 210pb (RaD). Its usefulness is that working level can be readily measured in both the field and the laboratory. Because of this, existing occupational exposure standards for radon daughters in both the U. S. and other countries use working level as their basis. In the U. S., the last twenty years has witnessed a significant reduction in radiation exposure standards from 120 working level months to 4 working level months per year. New international standards are being proposed that would be only slightly higher than these current U. S. standards. POTENTIAL EXPOSURES TO RADON DAUGHTERS The universal use of nuclear power, along with the transfer of nuclear technology to developing nations, has significantly increased the demand for fuels. As a result, uranium mining operations have expanded and increased numbers of miners are regularly exposed to radon daughters. In addition to potential exposures in uranium mines, other deep mines such as tin, gold, platinum and tungsten, also have potential exposures due to the distribution of uranium and its accompanying radium throughout much of the earth's crust. The energy crisis has also prompted interest in general population exposure to radon daughters in buildings. Many homeowners, using additional insulation and caulking to seal cracks and conserve energy, have reduced indoor ventilation to the point where working level exposure could become significant, especially in homes with unventilated crawl spaces. In fact, several serious exposure situations have occurred where mine tailings were used for building materials. MEASUREMENT TECHNIQUES Historically, rapid and convenient measurement techniques have been actively sought to improve the ability of ventilation engineers to limit mining exposures through ventilation control. A number of measurement techniques have been developed, including the Kusnetz method (further elaborated by Shalaynev) and techniques developed by Rolle and Tsivoglou. All, however, suffer from similar handicaps that prevent their usefulness in the mining environment. Their main limitation, in terms of minimizing employee exposure, is the elapsed time from the start of sampling until the results can be calculated. It is usually 40 to 90 minutes. This time delay presents both serious economic limitations as well as the potential for exposing workers to high radon daughter concentrations until calculations are completed and corrections made. Further reducing the utility of the Kusnetz and Tsivoglou techniques is the need for tedious calculations that increase the possibility of human error along with the need for cumbersome sampling equipment that is not ideally suited to the mining environment. INSTANT WORKING LEVEL METER To alleviate these problems, the idea of an Instant Working Level Meter was conceived by several groups. Several such instruments were proposed, built, and tested with disappointing results. Although the concepts behind them were sound, the instruments simply failed to measure working level without excessive distortion. In addition, their cost was relatively high, gamma background presented a problem, and sophisticated computations were necessary to determine working level. In short, these systems lacked the design engineering that would make them suitable for the demands of a mining environment.

Jan 1, 1981

By J. B. Fletcher

Miami Copper Company has used conveyor belts underground since 1947, At that time, the draw level for a portion of the orebody was only 25 feet above the haulage level To get the main haulage drifts as far away as practical from under the stoping area, 301, belt conveyors were used for lateral transfer, If the haulage drift was kept in good ground., a satisfactory draw of these stopes could be effected in that repairs to the conveyor drifts could be accomplished while drawing ore from the stopes. Some 7,400,000 tons of ore were mined with the 301d belt conveyor at a belt cost of approximately $0,004 per ton of ore. When the mining plan for a new section of the mine was laid. out in 1953, it was decided to use belts to collect the ore from the higher draw levels, and. move the ore laterally to centrally located concrete ore passes for transfer to the main haulage level (See Cut #1), The final plans used belt conveyors too collect from 3 stopes: on the 570 level, 2 stopes on the 720 level, and one stope on the 900 level. The six stopes to be mined in this manner would produce about 8 million tons of ore, and the sequence of mining was such that not more than four 400 feet conveyors would be in use at one time, Four conveyors using 36 inch, 4 ply belting were designed by the mine engineering office and fabricated at the mine shop, so that no piece was longer than 10 feet, and. the heaviest piece was the 25 horsepower motor, The head drive section, and the tail-pulley-takeup section were of bolted construction so they could be broken down for easing moving, Due to the size of the mine openings, the belt had to be transported into the mine in 400 feet rolls, requiring two splices for an installed belt. A torque arm speed reducer was used with a V -belt drive which made it possible to change the speed of the conveyor by changing the diameter of the V-belt pulley (See Cut #2).

Jan 1, 1958

By William S. Gilmer

INTRODUCTION As man moved through the ages into the era of metals, he became increas¬ingly dependent on the extraction and beneficiation of various ore types. His progression has required more material, new sources, and inevitably, a need to extract the values from ores of much lower yield. Inherently welded to this need to extract has been the attendant requisite of power and water to carry out these tasks. With the richness of these deposits diminished, and the in¬crease of demand, mining has become so intimately tied with the needs of these auxiliary systems that the modern day milling operation can ill afford to ignore them. In the times of Agricola 16th century methods of milling required little thought for power or water consumption. Reduction was accomplished by hand¬sorting and hammer and grinding done with stamps and millstones. Medieval concentration was carried out by the "Jigging sieve" with agitation supplied by the sleeveless arm of the operator (The Mines Magazine,_ March 1933). Little consideration was likely given to the power source unless it became apparent that he had insufficient means to meet the demands of a dawn to dusk operation. Fuel for power production was also probably of little consequence unless sustained drought or warring neighbors burned the miners fields. Water was available from any adjacent stream with recycle, potable, tailings and mill consumption all going and coming from the same source. By the end of the 18th century and the early 19th century the requirements of larger throughputs and better re¬covery were forcing the miner to the need for greater sources of power and water. Arrastras, capable of accepting several hundred pounds of charge, con¬sisted of a clay bottom, a "liner of rocks harder than the substance to be crushed" and a revolving center post in which the ore was ground and amalga¬mated. Used in conjunction with a slucing system, this formed the primary recovery method of the time. Power was supplied by horse or oxen or, if terrain was amenable, by use of a horizontal or overshot water wheel. A typical system required 4.5 kw (6 hp) and needed to run in the vicinity of 15 rpm (Pre¬ston, 1895).

Jan 1, 1986

By William Paul Robinson

I would like to first summarize the relevant health information relating to the workers and general populations around uranium mining as a basis for understanding the hazards associated with these operations and their available remedies. This discussion will summarize the literature on Radon and its daughters, among the most toxic uranium decay products. Second, I will discuss waste handling in the uranium industry: past, present and future, discussing exploration, mining, and milling and the volumes of water and solid and gaseous wastes which are associated with these various phases of uranium operations. This paper will also include a discussion of the various past and present materials handling technologies and their responsiveness to the concern for uranium waste isolation. I will then conclude with a summary of recent modifications in the relevant standards as applied to uranium mining and milling. Joseph Wagoner, a research epidemiologist with the U.S. Public Health Service has summarized the literature on uranium mining and its health effects in his written testimony as a commissioned witness in British Columbia Royal Commission of Inquiry into Uranium Mining in January of 1980, entitled Uranium, The U.S. Experience: A Lesson in History.1 Briefly summarizinq his report, as early as 1546, miners of uranium bearing ores in Central Europe were reported to have unusually hiqh frequencies of fatal lung disease2. As early as 1879, the real nature of pulmonary disorders among these miners was first diagnosed to be malignant neoplasia or lung cancers. Of 655 miners dying between 1875 and 1912, 40% or 276 of these Central Europe miners died of lung cancer.4 By 1939, it was reported that lung cancer mortality rate for miners in these Central European mining districts was several times (9.7 per 1000) higher than that for similar populations in Vienna, Austria (0.34 per 1000). Thus, before uranium mining began in the U.S., there was a considerable body of information linking uranium mining to lung cancers. The U.S. experience can be summarized in Table 1 also from Wagoner's B.C. Testimony.1 This table shows that through 1978, 205 respiratory cancer deaths have been observed among white underground uranium miners in the

Jan 1, 1980

By H Sohn, R. R. Fernández

Microscopic gold inclusions in sulfide minerals cannot typically be extracted by conventional cyanidation. The gold ore must be pretreated to oxidize sulfide minerals associated with gold and to remove other minerals and chemical compounds that interfere in the cyanidation leaching process. The recovery of gold from refractory sulfidic-carbonaceous ores after roasting pretreatment was studied. With the addition of an oxygen-containing gas (e.g., air or oxygen-enriched air), sulfides of iron, zinc. copper and other metals are tramformed into solid oxides or sulfates and gaseous sulfur dioxide at elevated temperatures (e.g., 400° to 800°C). When the sulfides are oxidized, individual particles lose internal volume and become porous, allowing leaching solutions access to the gold. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. These characteristics are strongly dependent on the roasting conditions and roasting method. The optimum combination of particle size, roasting temperature, reaction time and oxygen concentration in the off-gas was determined for a typical refractory sulfidic-carbonaceous ore from the Carlin Trend in Nevada. The tests were run using a 150-mm laboratory rotating tube furnace and 160- and 200-mm.fluid-bed pilot roasters. Laboratory results indicated that the maximum gold extraction was 92%, with the head and the leach residue containing 5.7 and 0.4 g/t (0.166 and 0.013 oz/st) Au, respectively. The maximum extraction was achieved under the following roasting conditions: a top particle size of 150 yin, a residence time of 2 hrs, a roasting temperature of 475°C and with 40% oxygen (by volume) in the off-gas. Similar results were obtained from circulating fluid bed (CFB) pilot-plant testing. The maximum gold extraction was 90%, with the head and leach residue containing of 5.1 and 0.5 g/t (0. 149 and 0.015 oz/st) Au, respective) v. These results were achieved with the same particle size and oxygen concentration as in the laboratory testing but with the roasting temperature of 500 ° to 525°C and a residence time of 30 min.

Jan 1, 2000

By G. Sanders

Discussion by G. Sanders The studies reported on in this paper were initiated to draw attention to the severe contamination problem in the Section 30 drilling program at Chimney Creek. The lithologic-subset sampling study reached a different conclusion from that presented in your paper, and I wish to comment on your subsequent analysis of the data and your conclusions. Request for more complete data In the section on subsampling, you mention that the subordinate lithologies were separated and sampled, yet only the dominantlithology gold value is plotted in Fig. 4. In a contamination study, the reader is interested in the assay values for the individual subsets. Please include a table of the subsample assay data in your reply. Also, please indicate which analytical methods were used to arrive at the gold values in the subsampling study. Turning barren rock into low-grade ore Figure 5 is very revealing and typical of all of the cross sections in Section 30. Note the long strings of low-grade mineralization spread out for hundreds of feet below the ore zones. There were some very high gold values found in certain contaminated fractions during the subset sampling. The conclusion, here, was that the distinctive, strongly-mineralized dolomite layer was probably loose and crumbly and continued to disintegrate during drilling. This caused salting of the unmineralized rock samples below. Missing the high-grade part of the ore body In your statistical analysis, you directly compare the reverse circulation assays to the diamond drill assays in Section 30. Two points argue against a direct comparison and suggest the differences are greater than the 3 % that you report. First, any core loss in a gold zone most likely means that the true gold values are greater. The drillers lost significant amounts of the clay-rich, Section-30 gold mineralization. Also, the initiated salt-mud system, an attempt to improve the core recovery, met with little success. Second, the practice of not sampling core geologically, but instead sampling on even 5-foot intervals, adds a deliberate dilution to the core assay values by including a portion of nonmineralized rock in the first and last samples of each high- grade intercept. The result is often a pair of low-grade assay values on either side of a high-grade gold zone. In reality, a high-grade gold zone has a very sharp assay wall that is often bounded by barren rock. This sampling method may make the diamond-drill core assays more like the reverse circulation values and may help explain the statistical similarities you found. However, it does not represent the true gold values in the high-grade parts of the deposit. You cannot deny that, by careful geological sampling of the drill core, higher and sharper assay values will be obtained. The low core recovery and the diamond-drill-core sampling method used act together to lower the diamond-core assay values. The 3% difference you found between the reverse-circulation and diamond-core assay values could be much larger when you consider what the true diamond-drill core values would be with optimum core recovery and a geologic sampling method for the core. Should statistics have been applied here? The statement "... that reverse circulation holes have overestimated the values of some ore zones and underestimated the values of others" (p. 345) is not correct. The subsampling confirmed what the cross sections hinted at in Section 30. Namely, beneath the high-grade zones, the reverse circulation holes created, by contamination, large intercepts of low-grade ore in regions of barren rock. Because the low-grade material was not there to begin with, this is not a process of overestimating low-grade mineralization. The next statement that "the average result is similar to that of the diamond drill holes" may apply to the data set numerically, but it is not true when viewed spatially on cross sections. Adjacent reverse circulation and diamond drill holes are almost impossible to correlate, high-grade zone values vary widely and many low-grade intercepts make no geologic sense. The subset sampling and cross sections presented in the first part of the paper show that the reverse circulation portion of the data set has some serious problems, as highlighted above, and should not have been dealt with statistically at all. Conclusion Each ore body is different, and each drilling method presents unique sampling problems. In this case, the diamond drill is the

Jan 1, 1994

By R. A. Metz, William H. Breeding

The remarks that follow are based substantially on experience covering 45 years, 80% of which has been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in intermediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1-1/2%. The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present. Most of the rich, readily accessible placers were mined by our forefathers. Current opportunities exist: (1) in remote areas where infrastructure has been absent in the past, or development has been prohibited by adverse ownership - political or commercial; (2) in deposits that could not be mined by equipment available to our forefathers; (3) in deposits unidentified by our forefathers; (4) where the-price-of-product/cost ratio is substantially better than in earlier years; or (5) a combination of those factors. When I entered the placer business in the late 1930s, and subsequently, a prevailing opinion believed that glacial deposits should be avoided as irregular in mineral content and composition, and unrewarding to explore and develop; yet an operator has been mining a fluvio-glacial deposit profitably for the past 17 years. Rich buried placer channels, often called paleo-channels were worked in the last century, generally by hand methods, and under conditions that would be unacceptable today. Exploration and mining equipment now available make some of these channels attractive targets. Well-known examples are in California and Australia. The formation of a commercial placer requires a source of valuable minerals. Above primary deposits, there may be eluvial deposits formed by the erosion of gangue minerals and the concentration "in situ" of valuable minerals. Down slope from these deposits are the hillside or colluvial deposits, and below them are the alluvial deposits of redeposited material. Most of the great placer fields of the world are the result of several generations of erosion and deposition. Well-known examples are in California and Colombia. Gold is a very resistant and malleable material, and gold placers may extend for 64 or 80 km (40 or 50 miles) along a river system. Platinum is less malleable, but is very resistant to disintegration. Diamonds are extremely hard, and (especially gem diamonds) may be found over great lengths of a river system. Cassiterite is less resistant to disintegration, and tin placers seldom extend over two miles without resupply from an additional source or sources of mineralizaton. Tungsten minerals are generally more friable, and within a few hundred yards of the source disintegrate to the point that they are uneconomical to recover. Rutile, ilmenite and zircon placers generally result from the weathering of massive deposits, and may be encountered over extensive areas; most are fine grained and durable. What does a geologist or mining engineer look for in placer exploration? The old adage to look for a mine near an existing mine is still valid. You need a source of valuable mineral. Then you require conditions for concentration, which means a satisfactory gradient and/or other conditions that will permit heavy minerals to settle. Nicely riffled gravel, often called a shingling of the bars, is conducive to placer formation. Coarser gravel is logically associated with coarser gold. Excessive clay and/or high stream velocities in narrow channels can carry gold far downstream and distribute it uncommercially over a large area. When material is extremely fine, in situ weathering and concentration become more important. Placers frequently occur distant from lode mines, and one must remember that in a larger watershed the exceptional floods that occur once in a hundred or a thousand years can move great quantities of material long distances. The carrying power of water is said to vary with the fifth or sixth power of its velocity. I am not ready to disagree with Waldemar Lindgren and accept that many commercial placers are substantially enriched by the chemical deposition of gold from solutions; however, I have seen crystalline gold in clayey material quite distant from known sources of primary gold that is dif-

Jan 1, 1992

By S. P. Chong, Peter V. Avotins

The iron and steel industry continues to operate at depressed production levels due to the low level of demand for steel and foundry products. Crude steel production in the Western world dropped by 13.7% from 459.3 Gt (506 billion st) in 1981 to 396.4 Gt (437 billion st). The reduction was particularly severe in North America where the industry suffered a loss of 37.3% from 123.6 to 77.5 Gt (136 to 85 billion st). This reduced level of production severely affected iron ore and agglomerates output. Substantial curtailment was made in both sintering and pelletizing plants to meet reduced demand. The pressure on these plant operators shifted from quantity to quality. With energy cost becoming an ever increasing part of production costs, conservation was a major area of emphasis. Iron Making Sinter has continued to be the favored burden for blast furnaces overseas. As hot metal production declined and excess sintering capacity developed, many of the overseas operators that have been using pellets found it advantageous on hot metal production cost to increase the ratio of sinter at the expense of pellets. This was the case despite the depressed price level of pellets in the world market. In North America where pellets have been the predominant burden material-mainly because it is necessary to pelletize the fine grain iron ores available domestically-there was also increased interest in sinter usage. Bethlehem Steel Corporation's 13.6-m (44.5-ft) furnace at Sparrows Point experimented with a burden with more than 70% of sinter during the second half of the year and indicated some favorable results as compared to its previous 50% super flux sinter and 50% acid pellet burden. The blast furnace operators continued to press for improved burden quality. In addition to the emphasis on the importance of burden chemistry and quality, uniformity, much emphasis was placed on improving reducibilitiy and high temperature metallurgical qualities. These burden properties were recognized to hold further promise in reducing fuels rates. Sintering With reduced consumption caused by the cutback in hot metal production, many sinter plants sat idle while others operated at greatly reduced rates. The deemphasis on production in many plants allowed them to experiment with various means to reduce operating costs. The most notable action was the introduction of low cost South American pellet feed fines into the sinter ore mix. These feed fines, which are finer than 150 µm (100 mesh) ore, were previously thought to be too fine for sintering. However, when the full production rate is not required the use of up to 40% in the ore mix was reported to be successful with the aid of burnt lime and adequate premixing and granulation of the sinter mix before sintering. The emphasis on quality and tighter cost control also has resulted in a further breakthrough in sintering technology. It was recognized that good feed preparation-including selection of compatible ores, good blending, good pseudo-particle formation, additive size control increased bed depth, and closed control of the sintering bed heat pattern-could allow the production of high quality sinters with much lower heat input and FeO level. Bed depth of more than 600 mm (23.6 in.) was practiced in a number of operations. Total heat input of better than 1.3 GJ/t (290,300 kcal per st) has been achieved. Kawasaki Steel's Chiba Works has also achieved a 5.3% SiO2 in the sinter with good quality. The low heat input approach allowed production

Jan 5, 1983

By M. Szatkowski

The studies conducted by Laplante and coworkers (1983,1984) with flotation of galena and quartz, showed that the rate of flotation reaches a maximum value for a certain intermediate value of the air flow rate. A similar, though less pronounced, effect of the air flow rate on the selectivity was also observed. Luttrell and coworkers (1985) showed that the size of air bubbles has a significant effect on both rate and selectivity of coal flotation. These two studies used flotation tests in which no froth layer was formed. This note describes effects of the air flow rate and bubble size on the rate constant and selectivity of coal flotation, using a mechanical laboratory machine with a froth layer allowed to form. Experimental A raw, dry ground Illinois coal was used in flotation tests. The size distribution and ash content of the samples are : Particle size (µm) Weight (%) Ash (%) +600 4.30 41.7 600/200 43.05 19.0 200/74 22.25 16.0 - 74 30.40 24.0 average 20.8 No. 2 fuel oil with a concentration of 200 g/t of feed and M.IBC with concentrations of 11, 22, and 33 mg/L of pulp (128, 256, 384 g/t, respectively) were used as flotation reagents. Tap water with a natural pH of 7.0 to 7.8 was used throughout the tests. No other reagents were used. The starting concentration of coal in the pulp was 86 g/L. A standard flotation machine with the pulp volume of 5 L was used in experiments. Three different air flow rates were employed, resulting in three air escape velocity values of 14, 30, and 70 cm/min. The air escape velocity (AEV) was calculated as the ratio of air flow rate (Qa) to the slurry surface (Ss) in the machine. For a comparison, the upper limit of air escape velocity values used in commercial size flotation machines is between 70 and 100 cm/min (WEMCO, 1983). A machine consisting of a generator of fine bubbles and a separatory column, described elsewhere (Szatkowski and Freyberger, 1985), was used for some tests where bubble size lower than that generated in the standard machines was required. Prior to a flotation test, a batch of coal was mixed with water in the flotation cell for at least 10 minutes to ensure that all coal was thoroughly wet. Then the specified amount of fuel oil was added and the pulp was conditioned for five minutes. The specified amount of MIBC was added 15 seconds before the end of conditioning. After air flow was opened, flotation products were collected for 0 to 30, 30 to 60, and 60 to 120 second intervals. Content of the combustible material in samples was determined by subtracting the ash content from 100%. A photographic technique was used to determine initial distributions of bubble size generated by the flotation machines. Bubbles generated in water containing the prescribed amount of the frother but no solids were photographed against a black background. The average diameter and standard deviation were then calculated for each set of flotation conditions. The method gives results reproducible within k 5% of the average bubble size. Table 1 contains information about the measured bubble size distributions expressed by the average bubble diameter (Db) and the standard deviation ( SD ) . Results and discussion The general formula for calculating the flotation selectivity is: o = recovery of coal/recovery of ash (1)

Jan 1, 1988

By Paul M. Jr. Musgrove, Donald C. Moore

Conventional Smelting Practice Conventional copper smelting practice varies from smelter to smel¬ter, but generally consists of some or all of the following unit processes: roasting, smelting, converting, and fire refining. Roasting. Copper sulfide concentrates can be smelted directly or after an initial roasting step. Roasting is used in some smelters because roasting prior to smelting increases smelting capacity, less energy is required to melt hot roaster calcines than wet sulfide concen¬trates, roaster off gases are high in Sot concentration, 5-15% SO2, and some volatile impurities are removed from the concentrate prior to smelting. However, many smelters do not use roasters, because the problems associated with handling hot dry calcines outweigh the advantages mentioned. Concentrate roasting is performed in multiple hearth or fluid bed roasters. If the moisture is low, roasting can be performed autogenously, usually at 500-600°C. High roasting temperatures are avoided because excess oxidation of the iron compounds may lead to magnetite formation. Magnetite is detrimental to reverb operation because mag¬netite can combine with refractory minerals to form a highly viscous slag. This slag prohibits efficient matte-slag separation and leads to excessive copper losses. Also, magnetite can settle through the matte layer, deposit on the furnace bottom, and consequently reduce furnace capacity. Roasting is carried out only on sulfide concentrates prior to smelt¬ing in reverb or electric furnaces. For smelting processes, such as the flash and continuous that rely on the exothermic heat of oxidation of the sulfur minerals, roasting is not practiced. Reverberatory Smelting. The predominate copper smelting fur¬nace for the past 50 years has been the reverb. These furnaces are typically 100-120 ft long, 30-35 ft wide, and 12-15 ft high. A typical furnace layout is shown in Fig. 2. Refractory brick linings cover all internal surfaces of the furnace. Originally the flame was directed to reverberate or reflect off the furnace ceiling and melt the feed material. Current practice is to direct the flame down the furnace length to melt the concentrate. A method of charging the concentrates or calcines, generally along the side walls to minimize refractory erosion, is incorporated in the furnace design. The copper concentrates, calcines, and fluxes charged into the reverb undergo a series of complicated reactions as the temperature of the mixture increases. The reaction of the iron and copper sulfides with the oxygen in the furnace produces a molten Cu25-FeS mixture called matte. Copper smelting metallurgy is based on the fact that sulfur has a greater affinity for copper than for iron and most other common metals. Therefore, in a system containing copper, the copper will preferentially remain as a sulfide compound until all of the other metals have been oxidized. The oxidized metals combine with silica to form a silicate slag that floats on the matte and is removed from the system. Reverberatory furnace smelting chemistry can be approximated by the following chemical equations: FeS2 + O2 - FeS+ SO2 (1) The formation of FeS ensures that any copper present other than as sulfides will be reduced by the relationship: CuO2 + 2FeS + O2 - CuS + 2FeO+SO2 (2) or 2Cu +FeS - Cu2S + Fe (3) As the molten charge travels down the furnace, continued oxida¬tion of the iron minerals and sulfurization of the copper minerals occurs. When all of the copper has been converted to sulfides, the iron sulfides can then be further oxidized as: FeS + (3)2 O2 FeO + SiO2 (4) The FeO reacts with the silica added as flux in the furnace charge. A simplified equation is: FeO + SiO2 -FeO SiO2 (5) The iron silicate slag formed is skimmed from the surface at the end opposite the burners. The copper content of reverb slag is usually less than 0.6% Cu and is discarded. Matte is removed along the side wall and is taken to the converter for oxidation of the remaining sulfur and iron. The main objectives in reverberatory smelting are to produce a molten Cu2S-FeS matte containing 30-60% Cu and a throwaway slag. Production of matte permits complete conversion of all copper minerals into copper sulfides, which can migrate because of specific gravity differences, through the lighter slag layer. Also, the molten matte droplets collect the noble metals, gold and silver, as the matte settles in the furnace. The large settling area of the furnace provides enough separation time to produce a low grade slag, which can be discarded without further processing. High heat losses are associated with reverberatory smelting be¬cause of the large volume of gases sweeping through the furnace. Therefore, an outside source of heat is required to keep the smelting reaction going. Natural gas, fuel oil, or pulverized coal are used as this heat source.

Jan 1, 1985

By Earl A. Berry

Someone once said, "The safest mine is one in which no one goes into." We all recognize this as being perhaps wishful thinking. We also recognize in it a certain amount of truth and an ultimate goal if we are optimistic. All of us are aware of the many things that have been done, are being done and will be done to reduce manpower in mining. For those of us; who are optimistic about this ultimate goal it would appear from the records-we are more than well on our way to the so called safest mine. Let us see what has been done in the past 20 years. T e period from 1935 to 1956. For example in the coal mining industry: In 1935 there were employed 462,903 men who produced an average of 805 tons per man per year or 4.50 tons per man per day. In 1955 there were employed 225,093 men who produced an average of 2,064 tons per man per year or 9.84 tons per man per day. There are no comparable figures compiled for the metal mining industry as a whole that can be broken down in this manner. However, from examination of figures available for different groups in metal mining there is a trend similar to that in coal mining. No-dbout the above figures reflect the intense development and perfection of machines and mining systems to tear out, transport and process our mineral wealth. The figures also show the mining industry has been able to double its production and at the same time reduce its manpower by half. When you compare the number of men employed today with the number which would have been employed 20 years ago to gain todays production at that time it become apparent that greater safety has been accomplished. For example the years 1935 to 1956 for all mining show. In 1935 there were approximately 649,226 men employed in mining and reports show 1,399 fatalities and 74,913 non-fatal injuries. In 1955 when there were 313,883 men employed in mining 496 fatalities and 25,365 non-fatal injuries were reported. To have produced the same tonnage of material in 1935 that was produced in 1955 it would have required the employment of approximately 1,298,452 men. 2,798 could have been fatalities and 149,826 could have had non-fatal injuries. You can now measure the full impact of what has been accomplished in the past 2o years by the aggressiveness of mine management, the wizardry of our engineering personnel and the thoughtfulness and devotion of our safety people and their programs. Therefore, there is a trend towards the goal of our opening statement. We whoare toptimistic believe this trend will accelerate at a-faster pace. Why? Because anyone engaged in the mining industry today can well afford to invest a minimum of $30,000.00 in capital equipment todisplace the labor of one man. This fact alone is a terrific incentive for mine management to apply and manufacturers to develop equipment of a type to get the men out of the mine. Now you can determine this problem not only becomes one of safety but also one of economics, When productivity is stepped up and manpower reduced management is learning the hard way what it means to them; in the profit and los s column when a few minutes of delay or downtime of costly machines and processes occur. They have learned that fast and efficient communication systems are the best means of combating breakdown, delays, bottlenecks, supply problems, the saving of lives and property and increasing production. One large western metal mine was able to increase Its tonnage by 4000 tons a day by using modernup to date electronic type communication system. The National Coal Board of Great Britain recently allocated 45,000,000.00 to study and develop faster and more efficient communications when a survey indicated what a serious bottleneck poor communication in their present systems of mining turned' out Lobe.

Jan 1, 1958

By R. A. Holmes

Although manganese is a metallic element and is widely dispersed in nature, it never occurs except as a compound in combi¬nation with other elements. Use of such compounds in the production of glass is known to have occurred in early Egypt. The dioxide of manganese was considered a compound of iron until 1774 when C.W. Schule first recognized it as an element. In the same year, a Swedish mining engineer, J.G. Gahn, became the first to isolate manganese. In 1856 development of the Bessemer process of steelmaking gave economic importance to manganese, and later, in 1882 Robert Hadfield discovered the benefits of high manganese steels. GEOLOGY Physical Properties Elemental manganese is a silver-gray metal, resembling iron but harder and more brittle and used primarily in alloys (both ferrous and non-ferrous) and a wide variety of chemical compounds. Some of the physical properties of manganese include: melting point¬1 245°C; boiling point-2 150°C; density at 20°C-7.43 g/cm3; specific heat at 25.2°C-O.115 cal/g; latent heat of fusion-63.7 cal/g; hardness on Mohs scale-5.0; linear coefficient of thermal expansion from 0 to 100°C-22 x 10-6. Mineralogy There are over one hundred minerals that contain manganese. These minerals vary from those with compositions that are pre¬dominantly manganese to those having only minor percentages of manganese. Distribution of Deposits Manganese ore deposits are found worldwide and were formed in various geological environments, but only a rather limited num¬ber of deposits have high grade manganese ore in sufficient quan¬tities to be mined and utilized economically on an industrial scale. It is worth noting the fact that almost all of the significant deposits can be classified into two types of deposits: marine chemical sed¬imentary deposits, and residual (secondary) enrichment deposits. There are, however, a much larger number of geological types but these are not of commercial significance at this time. Sedimentary deposits are the most common and are usually stratiform or lenticular. Manganese minerals were formed by a chemical process during the deposition of marine sediments. They usually contain manganese oxides and carbonate minerals, some¬times interbedded together or with other sedimentary rocks such as limestone or shale. Examples of this type of deposit are the Russian ore bodies of Nikopol and Tchiatoura, as well as the Kalahari deposits in South Africa and deposits of Groote Elyandt in Aus¬tralia. Residual deposits were formed in a different way: by alteration of existing manganese deposits or by concentration of the manga¬nese minerals when other minerals were washed away by weath¬ering or ground water processes. The Nsuta deposit in Ghana, the Amapa deposit in Brazil, the Moanda deposit in Gabon, and nodules in the residual clays of the US Southern Appalachians are examples of this type of geological process. In the case of the Ghana and the Amapa deposits, this is only true for the outer layers of the deposit containing oxide minerals, the inner part being comprised of car¬bonate minerals including manganese carbonate, probably from marine origin. Some sedimentary and residual-type deposits have been metamorphosed, giving rise to small high grade ore bodies. These deposits are regionally metamorphosed, occurring in mar¬bles, slates, quartzites, schists, and gneisses. Some of these deposits, such as the Franklin, NJ, deposit are rich enough to be commercial without secondary enrichment; however, most of the exploitable deposits have been secondarily enriched. Due to the diversity and complexity of manganese deposits, both with respect to deposition and chemistry, a wide range of impurities are almost invariably present in the ores. Table 1 shows that the reserves (i.e., a measured resource that can be economically and legally extracted) are estimated at 814 x 106 tons of contained Mn, which equates to more than a 100 year supply at the current level of production. The reserve base is made up of the marginally economic reserves and sub-economic re¬sources and are some 4.5 times greater than the proven reserves. Also apparent from study of Table I is the fact that some 75% of manganese reserves are found in two countries, the USSR and South Africa. On the other hand, North America (i.e., the United States and Canada) have few significant deposits. The largest deposit, or at least one of the largest, in the United States is located at Chamberlain, SD. This deposit is sedimentary

Jan 1, 1994