Search Documents

By J. D. Allen

The Concord Mine Coal Preparation Plant of United States Steel Corporation, located near Bessemer, Alabama, began operations in June, 1950. The basic cleaning circuit consisted of a Chance Cone for cleaning the 2-inch x 3/8-inch fraction and concentrating tables for cleaning the minus 3/8-inch coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable (Figure 1), 85 per cent passing three mesh and 25 per cent passing 28 mesh, there was a considerable amount of fines passing through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-foot diameter hydro-separators with the underflow returning to the dewatering screens and the overflow going to a 175-foot diameter thickener for water clarification, (Figure 2). As might be expected, there was a considerable amount of recirculation of the minus 35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20 per cent. Further reduction to approximately 11 per cent was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a smaller percentage of the coal previously used at the coke plant, the high moisture and fluctuations did not seriously hamper coking operations.

Jan 1, 1966

By Weibai Hu

The flotation separation of wolframite from fluorite and quartz is investigated with chelating agents and neutral oil as synergic collectors. Test results indicated that a-nitroso-ß-naphthol has a strong collectivity for wolframite and selectivity against fluorite and quartz. The 8-hydroxyquinoline has collectivity and selectivity also. They both have a better activity than sodium oleate. However, the cupferron is slightly inferior. The synergism of chelating agents and neutral oil looks promising, especially for fine wolframite particles. The activation effect of Fe2+ and Ca2+ ions on separation of wolframite from fluorite and quartz is slight. The UV absorb-spectra measurements showed that the adsorption of chelating agent on wolframite is multilayer, and flotation behavior is related to chemisorption. The chelating agent which bonds to Fe and Mn sits on the wolframite surface, and the reaction between Mn2+ ion with collector is more significant. The essentials affecting reagent activities are the bonding factor and the hydrophobic factor. These factors are discussed by structure-activity relationship theory. The synergism of neutral oil is a secondary collector likely to lengthen the hydrocarbon chain of chelating agents.

Jan 1, 1985

By T. G. Melkus

A Setaram C-80 heat flux micro- calorimeter was used to study the surface and interfacial properties of fine coal particles in water containing flotation agents via heat of immersion measurements. Heat of immersion (?Himm) is usually a small exothermic quantity and can be used' to characterize a solid in terms of its relative hydrophobicity or hydrophilicity. The effects of coal type, surface oxidation, mineral matter content, kerosene concentration, and pH on the wetting characteristics were investigated. Results obtained from the calorimetry experiments correlated well with results from independent flotation experiments.

Jan 1, 1987

By S. Tan

In this paper, several commonly used computer truck dispatching criteria are evaluated. A computer-oriented truck dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics, and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. All basic dispatching criteria including minimizing truck waiting time, minimizing shovel waiting time, minimizing truck saturation, maximizing truck momentary productivity, or truck routes optimization provide a local optimal solution. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely. Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. However, based on the simulation results of the mine operation, several dispatching criteria which have good potential to increase performance can be selected. It may be necessary to search for the best combination of these truck dispatching criteria for a given situation. For example, a truck flow measurement such as the truck clustering factor at shovels can be used as a switch parameter to change from one criterion to another. The values for the switch parameter at which actions should be taken to change the criterion can be established through simulation programs.

Jan 1, 1992

By W. H. Davitt

One might ask why someone like myself, involved in the determination of taxes, should be speaking at a "cost engineering" session of a national engineering society. While it is true that taxes, especially income taxes, whether they be federal, state, or local, are not usually thought of as a "cost" of doing business, it is equally true that these tax costs do reduce the distributable profits just as much, as the cost of power, supplies, or labor. Therefore, the consideration given to taxes is often as important as that given to other costs. Hopefully yea will recognize that, within certain limits, taxes can be controlled to an economic advantage. That question may then lead to another question: What does the amount of taxes have to do with me? I'm an engineer or manager; not an accountant or a lawyer. If I may take a few minutes of your time, I might be able to present in a brief discussion some interesting facts that will provide the answers to those questions. My discussion will be directed mainly to Federal taxes. However, much of it will be applicable to state and local taxes, also.

Jan 1, 1973

By J. Herbst, A. J. Lynch, E. V. Manlapig, G. C. Throne, J. S. Hall, G. Poling

Modelling of industrial sulphide flotation based on data collected in several flotation plants is discussed. A mechanistic approach is used in which it is recognised that flotation is a two stage process with concentration occurring both in the pulp and in the froth. The important features of the model, which is a kinetic model, are – 1. for each particle species there is a range of flotation rates which corresponds to the range of particle sizes, 2. the flotation rates of the liberated gangue particles which have no hydrophobic properties are dependent on the flotation rate of water and are controlled by variables such as the air and frother addition rates, and the pulp level, 3. as an approximation the valuable sulphide particles may be regarded as being present in two groups with high and low flotation rate constants, 4. increase in the addition rate of collector tends to increase the proportion of sulphide particles which are in the high flotation rate constant group. The actual flotation rate of each group of particles is a combination of an "inherent" flotation rate and a flotation rate which is dependent on the flotation rate of water, at particular air and frother addition rates and pulp levels there is a physical limit to the rate at which particles can be transported into the concentrate and this is recognised in the

Jan 1, 1976

By Burton H. Boyum

The paper generally reviews the iron ore occurrences and regional geology of Western Australia, but features in particular the mesa deposits of PJasic Materials - Cliffs International. Initial production is planned from a aeries of mesa deposits of Eocene-Oligocene age. The ore is oölitic to pisolitic goethite and hematite. Source of the iron in the mesa deposits is thought to be from the Precambrian iron-formations. The geology and occurrences of the mesa iron ore deposits are summarized and illustrated.

Jan 1, 1964

By Bo R. Arvidson

High-energy product permanent-magnet materials of rare-earth cobalt alloys are being used in applications where space or weight are at a premium cost. New applications like friction-free bearings are also made possible. However, such magnet materials have not been commercially used in magnetic separators until now due to the high cost for the overall magnetic flux generation relative to commonly used ceramic magnets or AlNiCo magnets. The design of the new high-intensity permanent- magnet roll separator (PERMROLL) takes advantage of the unique properties of rare-earth cobalt magnets rather than just substituting for conventional magnet materials now in use for magnetic separators. Hence, the new generation of high-intensity magnetic-roll separators has some unusual characteristics that make known magnetic separation applications more economically attractive, and even expands the magnetic separation technology area to include applications for which no other feasible methods are presently known.

Jan 1, 1983

By Konstantinos Komnitsas, Evangelos Petrakis, Emmanouil Varouchakis

The paper discusses the limitations of population balance modeling (PBM) in predicting particle size distribution in grinding systems. It introduces a nonlinear framework that transforms the batch grinding equation into the Rosin-Rammler distribution, providing more accurate analysis under different operating conditions. The study uses marble as test material and investigates the adaptability of the nonlinear model with different media sizes.

Oct 1, 2023

By James C. Cobb

Middle Pennsylvanian (Desmoinesian) coals of certain areas of the Illinois and Forest City Basins contain epigenetic sphalerite and associated minerals in veins, clastic dikes, cleat, and other small-scale structural features. The presence of sphalerite in these coals records information about the geology of coals and coal basins, and represents a potential source for zinc as a byproduct of coal production. Origin of Sphalerite in Coal The origin of sphalerite in coal suggested by Cobb (1) involves sphalerite precipitation from zinc-bearing ?Na-Ca-Cl brines upon contact with sources of sulfur in the coal bed, e.g., pyrite, H2S, and organic sulfur. These brines were essentially at the temperature of the host coals as determined by fluid-inclusion thermometry and vitrinite-reflectance studies. The migration of these brines into coal beds may have been caused by compaction of sediments due to continued sediment loading of the coal basins. Zones of high permeability such as sandstones and the coals themselves presumably acted as conduits for the movement of the brines. The open spaces where sphalerite was deposited resulted from minor deformation associated with differential compaction and cleat formation enhanced by volume shrinkage during coalification.

Jan 1, 1982

By Raymond L. Zahradnik

Marco Polo reported that the Chinese used "black rocks" for fuel, and recent studies indicate that the Chinese may have used coal in small amounts for two or three millennia previously. The use of coal as a major source of energy however, did not begin until about the twelfth century, when the inhabitants of the northeast coast of England discovered that certain black rocks found along the seashore--and thereafter known as "sea soles" would burn. Since this initial discovery, coal has been mined continuously, first in England and shortly thereafter in present Belgium, France, and Western Germany, and finally in all coal-bearing areas of the world, in ever increasing amounts. The production of coal in the United States began about 1820, when 14 tons were reportedly mined. Since that time the production of coal increased steadily until about 1907, after which the rate has fluctuated between the extremes of about 400 and 700 million tons per year. Bituminous coal and lignite production was 590 million tons in 1974. Value of production was $8. 9 billion. Anthracite production was b.3 million tons with a value of $157.5 million.

Jan 1, 1975

By W. Porter Place

The Trolleyphone was the first successful application of carrier current techniques to a DC power distribution system to provide voice communication between fixed points and moving locomotives and traveling cranes, This was a significant breakthrough because this not only in itself provided a useful new tool for industry, but the knowledge gained in the transmission of voice communication is paving the way for many other things, chiefly, remote control and indication systems which promise to have a far reaching effect during the upcoming age of automation. Once it has been established that we can communicate between men who operate machines, the next step will be to operate the machines themselves.

Jan 1, 1958

By P. Soros

To accommodate the immediate and long term growth of the Hunter Valley, one of Australia's major coal producing regions, a third coal terminal was required in the Port of Newcastle, N.S.W. The initial capacity required was 15 million tons per annum, made up of 40 different blends, to be expanded to 50 million tons of 100 different blends, made up from 70 grades. Coal arrives in 3,200 ton unit trains, a total of 16,000 trains in a year.

Jan 1, 1986

By T. M. Storer

Much has been written and many discussions held on the virtues (and evils?) of a Company-owned motor fleet. Almost invariably these dialogues take a generalized form and thereby lose something since the individual circumstances, geography and philosophy - particularly in diverse industries, is never quite the same. In considering the nature of my remarks today, I felt a departure from the general approach might be in order, and in lieu of that, will attempt to present a concise picture of how we in the Lehigh Portland Cement Company view this problem and the steps we have taken in our efforts to solve it. At the outset a word may be in order about the Lehigh Company itself, what we do, and the problems that confront us specifically as well as the cement industry at large. We are primarily a manufacturer of portland cement operating 10 plants with a total annual capacity of about 23,000,000 barrels. We market this material in 30 states, shipping both from the plants directly as well as through a system of 18 distribution terminals. About 150,000 truckloads of cement are shipped to customers each year.

Jan 1, 1969

By Norman M. Junk

Following the wide-spread acceptance of ANFO as a useful, low cost blasting agent, studies have been made to adequately describe the physical and explosive properties of this material (1). As the quality of the AN blasting prill improved, reliability and sensitivity to initiation were greatly increased and many methods of priming were chosen from the standpoint of economics with little appreciation for the need to initiate so as to obtain the most efficient detonation. Under certain conditions, ANFO could be initiated with primers no more powerful than a No. 8 blasting cap (2). Research on primers for ANFO followed and it was demonstrated that this blasting agent was subject to extreme transient velocities upon initiation with wide variations in energy output depending upon the nature of the primer. For these reasons it was shown that powerful priming was economically justified (3). These studies helped to define the properties of an effective primer and the guides for its efficient use. In the vast surface coal mining industry, technological advances in earth moving equipment were paralleled by the development of larger and larger borehole drills (4). Even though ANM) was the major blasting agent used in this industry, investigations of priming techniques in these larger boreholes was almost non-existant. In 1962, Mr. Cleon Woolsey of Enos Coal Company disclosed to the industry that dramatic improvements in blasting production could be achieved with new priming and boostering methods (5). The research program at the Atlas laboratories was designed to explain these results and extend the study of initiation of ANFO with both high explosives and slurry explosives and to define the principles involved.

Jan 1, 1968

By Kenneth P. Neumann

The development of the Cyprus Thompson Creek Molybdenum Deposit near Challis, Idaho, began in 1967 when the first mining claims were staked on the intrusive rock outcrop. Exploration drilling continued for the next 14 years. During 1978, a decision was made to develop the deposit. In December, 1980, approval of the Environmental Impact Statement was received and construction of facilities and waste rock removal began. By the middle of 1983, 126 M metric tons of rock had been removed and all facilities were completed. The high work ethic of Cyprus Thompson Creek employees combined with innovation has made the mine one of the most efficient in the United States today.

Jan 1, 1983

By Keith K. Griffiths

Computers are a valuable tool to the aggregate industry and should not be overlooked. The selection of proper mechanical components is necessary. Merely the addition of a computer to operate a mechanical system will not guarantee that the system will work. Material delivery by rail or truck for stock-piling and intra-plant material transfer can be accurately supervised by automation with simplified controls for the layman to use. There are mechanical problems that occur in material blending and load-out systems when such a system is automated. Such things as material flow, bridging, stockpiling methods, overloading of equipment and safety must be considered. How these problems can be overcome by proper selection of compatible mechanical and computer equipment will be discussed. Also, there are many individual material circuits in a plant that can be computerized at a nominal cost. This type of computer installation will not necessarily result in increased production, but it will produce greater efficiency in manpower. These small computers, binary counters, memory circuits and other devices and their application to the aggregate industry will also be presented. A careful evaluation of the mechanical and computer inter-relationship by someone understanding both "Rocks and Electronics" is essential to proper handling of material by computers. Computers for the mining industry may be either digital or analog computers. Unless the computer is to control some type of chemical process, such as a cement plant, the, analog computer is not required and the digital computer' will be quite adequate and less expensive.

Jan 1, 1967

By William F. Lawrence

Within ten to fifteen years, coal-fired power generating stations will be producing over 40 million tons of coal-ash annually in the United States. The largest part of this ash will be emitted from the boilers, entrained in the off-gas stream and trapped as flyash. However, about 15 percent (six million tons) will he removed from furnace bottoms as bottom ash or molten coal-ash slag. In current practice, the molten coal-ash slap is generally water quenched and then transported either as a slurry or in granular form to storage or disposal areas. Although a small amount of this slag is marketed as abrasive grit or as roofing granules, most of it is considered a waste material which must be disposed of at considerable cost to the power companies and therefore to the public. The accom¬panying economic loss in terms of unused raw materials and displaced land is not as obvious but is just as real. The Coal Research Bureau at West Virginia University under the sponsorship of the U. S. Bureau of Mines has been examining the possible utilization of both coal-ash slag and flyash in the mineral wool industry as a method of partially alleviating the growing national problem of solid waste disposal. The potential marketing situation for mineral wool manufactured from coal-ash is illustrated in Figure 1. This bar graph depicts the growth in value of mineral wool shipments1 from 1949 through 1966. In this 17-year period, the value in¬creased by over 350 percent, more than 20 percent per year, despite a decrease in unit cost of mineral wool. It therefore appears likely that coal-ash could find a steady market as a supplement to existing sources of raw materials for mineral wool production.

Jan 1, 1970

By Lawrence E. Mannion

In southwest Wyoming lies buried the world's largest source of natural sodium carbonate, or soda ash. Perhaps a hundred billion tons of trona (sodium sesquicarbonate) are contained in ancient lake beds in the Green River basin'). There the Green River Formation encloses more than 40 extensive beds of trona. At least 25 of these exceed 3 feet (1 meter) in thickness and most of them are more than 300 square miles in extent. Five have been exposed in mines and lie between 800 and 1500 feet below the surface. Others lie at depths of from 400 to 3500 feet. Three companies have underground mines that supply trona to adjacent soda ash plants. These are the FMC Corporation, Allied Chemical Corporation, and Stauffer Chemical Company. A fourth, Texasgulf Corporation, has a mine under development. In 1974, annual soda ash capacity in the Green River area was approximately 4,300,000 tons, which requires the mining of about 7,500,000 tons of trona.

Jan 1, 1975

By D. J. Beeby

California's Surface Mining and Reclamation Act (SMARA) was passed in 1975 to identify and protect mineral resources in areas of high land-use conflict and ensure reclamation of mined lands. Under SMARA, aggregate resource availability is quantified and compared to forecasted demand in specific market regions. Fifteen regions studied thus far cover 20,000 square miles and contain 50 billion tons of high-quality aggregate resources which have been legally designated as ?regionally significant?, providing a measure of protection previously unavailable. SMARA reports and State testimony at local hearings have supplied objective information and helped reduce conflict in mine-permitting decisions.

Jan 1, 1987