Search Documents

By James J. Broderick

In the production of Pig Iron - Limestone, Coke and Iron Ore pellets are changed to the blast furnace and reacted at approximately 2,800 degrees F. The resultant products are molten iron and a molten slag - not unlike lava. The molten slag stream is channeled into open pits, cooled with water, crushed and sized for various industrial applications. The production of steel from pig iron in open hearth, B0P, BOF and electric furnaces results in somewhat similar slags: but since free lime is normally the flux, the resultant slags are not satisfactory for use in cement pastes. When exposed to water, the lime slakes, expands by 250% and ruptures the concrete. Thus, the slag discussed first is Blast Furnace Slag composed of 30 to 40% Silica (SiO2) Alumina (AL202) 7 to 16% Lime (CaO) 32 to 45% and Magnesia (MgO) 5 to 15%. The oxides do not exist as free oxides but rather as silicates and alumino silicates which are chemicall inert. Since transportation costs limit the area of use, blast furnace slag can only be found in concrete products produced within 60 to 100 miles of a blast furnace operation. Even within these areas where slag is in heavy supply, quite often the use of slag is minimal for concrete aggregate and the major outlet is road base.

Jan 1, 1985

By L. D. Boughton

Solution mining projects are conducted through one or more boreholes which penetrate en ore body. Proper drilling, completion and maintenance of the boreholes, therefore, is essential to the success of any solution mining operation. Wells drilled for solution mining encounter problems quite similar to problems encountered by the petroleum industry in drilling, completing and maintaining wells for the production of oil, gas or water. Many of the services developed and much of the experience gained by the petroleum industry is applicable to solution mining wells. As in the petroleum industry, each individual wellbore and ore body in a solution mining project provides its own problems. These vary greatly from well to well, and it is not possible to set down data or outline programs that will apply to all wells. Instead, the design of the drilling, completion, production and maintenance programs should be worked out for each individual well. The purpose of this paper, then, is to generally describe materials, equipment and techniques available for these programs and to discuss the purpose and sequence of their use.

Jan 1, 1971

By Robert E. Hershey

The phosphate industry is the fourth-ranking mineral industry in Tennessee; it has an annual value of 13,000,000 and a yearly production of almost 2,000,000 tons of phosphate ore. Tennessee, at present, is second in rank of phosphate production in the United States. In accord with the importance of this mineral commodity, the Tennessee Division of Geology, is conducting a continuing study of the industry' and the raw s, materials upon which it is dependent. Of the three type's of phosphate found in Tennessee, the brown phosphate rock of the Bigby faces of the Bigby-Cannon limestone is by far the most extensive in occurrence and is the only type being mined at the present time. Because of the importance of the brown phosphate ores, our Division has mapped , in detail the outcrop pattern of the Bigby facies of the Bigby-Cannon limestone. The geologic mapping was done by Dr C. W. Wilson, Jr. and others under his super-vision and the geology plotted on 7 1/2-minute topographic maps, with scale of 1 to 24,000 or 1 inch equals 2,000 feet. These maps will be available for use in the near future and will be published later-with complete geologic coverage.

Jan 1, 1960

By C Rutter, N Shea, K Kolobe

The Henderson mine, a panel cave mine in Colorado, has undergone multiple ventilation system changes to meet dynamic airflow needs. This paper explains the ventilation designs for different production panels, the challenges faced, and the modifications made to optimize the ventilation systems. The study highlights the importance of a robust ventilation system for safe and productive mining.

Mar 2, 2022

By W. A. Hockings

This report describes a computer program for the solution of material balances in complex mineral processing flowsheets. The program, which is entitled MBS Metallurgical Balance System), evolved as the culmination of a series of material balance programs whose development began in 1967 at the Institute of Mineral Research, Michigan Technological University. The need for such a program became evident when the Institute became heavily involved in a large number of short-term pilot plant projects. Calculating material flows from analytical data by means of the standard two-product formulas grew increasingly difficult and time-consuming as the complexity of the flowsheets increased and as choices between conflicting analytical values had to be made. It was recognized that what was needed was a program that would assimilate all of the available data and calculate mass flow rates so that steady-state inputs and outputs would balance at each point in the flowsheet. Such a program should be capable of handling underdetermined, overdetermined and mixed systems, and when the given data are inconsistent, the program should adjust the data in such a manner that the adjustments are minimized. Missing analyses should also be calculated whenever possible. In addition to solving material balances, the program should be convenient to use and print out the results in a useful form. Thus, the inputting of data should be simple enough to be handled by relatively untrained personnel with diagnostic messages being printed out to identify errors and anamolous data when they occur. Most importantly, the program should produce well-formatted output which can be directly included into a report without the necessity of retyping. The proper spacing of table titles, column headings and the ability to control the columns being printed are important features in this respect.

Jan 1, 1977

By D. Lelinski

Air-sparged hydrocyclone (ASH) flotation is one of the new promising technologies. Numerous applications have been successfully tested since its conception; nevertheless, research and development efforts have continued to provide for further improvements with respect to operating conditions and design considerations. Results from experimental studies on bubbles generation in the ASH system are presented in this paper. Bubble size distributions generated during ASH operation have been determined using a high-speed photographic technique. The influence of many factors including surfactant concentration, water flowrate, and porous tube pore size has been studied. Test results indicate that these process variables have a profound effect on the bubble size distribution. With an increase in surfactant concentration or water flowrate (shear field) the bubble size distributions become narrower and shift toward smaller average bubble diameters. However, the influence of pore size is more complicated. Depending on the experimental conditions the average bubble size was found to range from about 100 to 300 microns in diameter.

Jan 1, 1995

By L. V. Wade

The use of longwall/shortwall mining systems is under increasing scrutiny by the U. S, coal industry as a means to reverse the decline in productivity. The success of these mining systems depends to a great extent upon designing the system hardware to best suit local conditions. Of particular importance in this regard is designing the various elements of the total ground support system, including face, face end, and gate road supports, to accommodate local geologic conditions. This presentation centers on the problem of selecting the face support system. The existing geologic situation can influence the selection of the face support hardware in a variety' of ways. In general terms, these influences can be grouped into the following four areas: 1. The capacities required of the support unit; 2. The roof, coverage supplied by the support units; 3. The flexibility required of the support unit to meet changing geologic conditions; and 4. The required stiffness characteristics of the individual support units both vertically and horizontally. The following will center on the first area, i.e., the required d capacities of the support unit, in particular, the maximum required load density for a particular geologic situation.

Jan 1, 1976

By John Murray, Ryan Smith, Daniel Ebin, Robert Gould, Thomas Hennings

The Atlanta Plane Train Tunnel West Extension was excavated at Hartsfield-Jackson Atlanta International Airport using Sequential Excavation Methods (SEM). At its shallowest point, tunnel cover to bottom of Domestic Terminal footings was limited to 6 feet in soft ground. To mitigate risk of excessive building movement due to tunneling-related activities, the columns near the alignment were directly underpinned. Underpinning was accomplished using a combination of grouted mini-piles, installed under low headroom conditions, that supported steel framing spanning over the tunnel excavations. This paper focuses on design and construction of the underpinning system used to mitigate risk from tunneling.

Jun 13, 2023

By R. Chandramohan, Landon Jackson, C. Meinke

Understanding constraints within the raw battery material supply chain is essential for making informed decisions that will ensure the battery industry’s future success. The primary limiting factor for long-term mass production of batteries is mineral extraction constraints. These constraints are highlighted in a first fill analysis which showed significant risks if lithium-ion batteries are used to fully support vehicle electrification and intermittent energy storage. Nickel, lithium, cobalt and graphite reserves risk 100 percent depletion with significant consumption of known resources. Furthermore, more than 700 new critical mineral mines will need to be developed to meet the required production rates for decarbonization by 2050. Demand for critical minerals will outpace mine development timelines even as improvements are made to battery energy density and compositions. Governments and the private sector need to align themselves on decarbonization goals to establish cooperative agreements on the critical mineral supply chain by reducing the barriers to entry and increasing exploration efforts. Additional measures must also be taken to reduce the demand for critical minerals. Policy such as incentivizing public transportation and biking infrastructure can be exploited to drastically reduce the mineral demand placed on the mining industry.

Feb 1, 2025

By N. Careddu

In recent years, slabs with a rough surface have captured a large share of the ornamental stone market. However, the main technologies used for this type of treatment are based on mechanical shock (bush-hammering) or thermal treatment (flaming or flame-finishing). These traditional technologies are widely used, but have many limitations that decrease their usefulness. The purpose of this study was to develop a technology that enhances the natural colors of the rock and produces a rough surface without compromising its mechanical characteristics, in contrast to traditional technologies. This report shows the technical, economic and aesthetic results obtained with a new water-jet treatment and compares it with competing technologies.

Jul 1, 2010

By A. J. S. Spearing, B. Forbes, T. Kostecki, A. Hyett

Improving upon the past understanding of the interaction between installed rock bolts, the immediate roof and sidewalls is vital for the implementation of sound support system design, as this has a direct impact on rock-related safety. This is the primary goal in rock-bolt-related research. The earliest research in this field concentrated on limited laboratory and in situ measurements accompanied by theoretical analyses, based on the Kirsch equations. This represented the initial insight into understanding relative ground movements and their impact on primary support. However, these studies were far from complete. More recently, major technological advances in computing power within the mining industry has changed the scope from theoretical analysis to computer simulation. Even with these advancements our understanding of rock bolts in situ and in the laboratory has not progressed, particularly concerning bending and shear. To measure the behavior of rock bolts, the widely accepted practice is to populate the bolts with an array of strain gauges. Historically, resistive foil strain gauges or long displacement sensors have been used. Additionally, all instrumented rock bolts have used only two diametrically opposed slots. Rock bolts instrumented with these methods have significant shortcomings, one of which is the inability to capture shear and bending. The shearing and bending of rock bolts are particularly common in tabular soft rock mining, such as coal mining. This paper discusses the use of three slotted rock bolts, cut diametrically 120º apart, and two new optical fiber technologies populated along the entire rock-bolt length.

Jan 1, 2015

By S. Frimpong, G. Galecki

Dump truck tires are often used in long-haul roads in rugged terrain, with high rolling and grade resistances. These conditions increase the ton-kilometer-per-hour (tkm/hr) or short-ton-mile-per-hour (stmph)rating of tires, leading to tread wear, cuts and complete failures. The load-bearing capacities of these tires are sometimes exceeded, with truck overloading, overstressing, heating and subsequent failures. In addition, truck tire demand far exceeds the current supply capacity, with long lead ordering time. This condition has caused severe tire shortage, and the problem is expected to be sustained in the long-term. Industry has taken extensive practical measures to prolong tire service life with significant results. However, this problem can be solved through fundamental and applied research initiatives. This paper pioneers a research effort in tire service life using multibody physics, fatigue failure modes and soil failure dynamics to develop tire-road contact force dynamics. A virtual prototype simulator of the tire-road contact, using the CAT 775E (with standard tire 24.00R35) was developed and simulated within the MSC.ADAMS/NASTRAN environments. The results show the areas of the loaded tires with maximum Von Mises, principal and shear stresses, which could result in fatigue failure, tire wear and tear and blowouts. The maximum Von Mises stresses on the six truck tires are between 35 and 58 MPa. The maximum shear stresses are also between 19 and 33 MPa. These stresses will cause early tire failures given an average operating schedule of between 20 and 24 hours per day. The isolated areas with maximum stresses will be subjected to further studies to reduce stress intensity while preserving tire performance.

Jan 1, 2012

By F. Varley, J. Whyatt

A variety of dynamic failure cases with regional impact were described at a bump symposium held in 1958. These types of events, while rare, are of particular interest because their ability to impact a large area has disaster potential. These cases can be grouped into two broad classes of events by mechanism. These are (1) a slip along steeply dipping faults and (2) the fracturing of strong strata above or below the coal seam. Both failure modes produce dynamic or “shock” loads on the perimeter (roof, rib and floor) of mine openings. Special consideration should be given to these failure modes in the planning of deep coal mines, since their occurrence is not within the professional experience of many contemporary workers. In addition, their potential is not evaluated by many of the analysis tools commonly used to evaluate hazards in coal mine plans.

Jan 1, 2009

By F. Daviess

A requirement for geological controls during orebody modeling results from the recognition of heterogeneous geological characteristics and/or abrupt variations in orebody geometries. While purely statistical methods are often sufficient for modeling uniform homogeneous deposits, and the only recourse for many that are extremely complex, geological interpretations can be extremely valuable as controls during the modeling process. The advent of relatively inexpensive, sophisticated graphical computer hardware and software has focused considerable attention on the three dimensional visualization capabilities now available to the mining industry. Orebody geometries can be easily imported into many systems as wireframe or solid models, rendered with shading and color, rotated in space, exploded into composite parts, zoomed into and otherwise displayed to awe any audience. The requirements for an initially meaningful, accurate, geological interpretation are sometimes lost when the focus is on an apparently complex, highly resolved end product. Details of the initial data and sensitivities of modeling assumptions are not always sufficiently scrutinized. Software capabilities have extended the geopoetic license into three dimensions. The new tools, while greatly facilitating model construction and rendering, have done little to expedite basic data preparation and analysis. This paper attempts to briefly summarize the purpose and method of the construction of geological controls. The examples selected are from wire­framing and block modeling; application software processes commonly used in the mining industry today.

Jan 1, 1992

By G. Frey, D. Scott, C. Pritchard

Controlled recirculation has been used in the metal/nonmetal mining industry for energy savings when heating and cooling air, in undersea mining and for increasing airflow to mining areas. For safe and effective use of controlled district recirculation, adequate airflow to dilute contaminants must exist prior to implementation, ventilation circuit parameters must be accurately quantified, ventilation network modeling must be up to date, emergency planning scenarios must be performed and effective monitoring and control systems must be installed and used. Safety and health issues that must be considered and may be improved through the use of controlled district recirculation include blasting fumes, dust, diesel emissions, radon and contaminants from mine fires. Controlled recirculation methods are expected to become more widely used as mines reach greater working depths, requiring that these health and safety issues be well understood. The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted two controlled recirculation tests over three days at a Wyoming trona mine, utilizing an inline booster fan to improve airflow to a remote and difficult-to-ventilate development section. Test results were used to determine the effect that recirculation had on air qualities and quantities measured in that section and in other adjacent areas. Pre-test conditions, including ventilation quantities and pressures, were modeled using VnetPC. During each test, ventilation quantities and pressures were measured, as well as levels of total dust. Sulfur hexafluoride (SF6) tracer gas was used to simulate a mine contaminant to monitor recirculation wave cycles. Results showed good correlation between the model results and measured values for airflows, pressure differentials, tracer gas arrival times, mine gasses and dust levels.

Jan 1, 2013

By M. J. Langley

Zinc ores were first discovered in Tennessee in 1856 at Jefferson City where a deposit of oxidized ore became known as the Mossy Creek Mine. From that time until 1913 small scale attempts at prospecting and mining were made in various parts of the district. The actual systematic development of the zinc deposits dates from 1913 when the American Zinc Company started operations at Mascot. Six mines are in operation by three companies and a seventh mine is being developed by a fourth company. The total daily production from the field is 11,000 tons of crude ore, which grades from 3 to 6 per cent zinc. Most of the ore bodies are large and ramiform, resembling asyrmetrical networks in which the ore shoots form channel like branches with areas of non-comercia1 rock, called blank islands. Most of the orebodies are adapted to large scale mechanization.

Jan 1, 1962

By Charles E. Dandois

New is a relative term, and, when used with reference to a concept as old as shaft kilns can be applied to a number of designs. In this case the design that is the subject of this paper, is known as the ring or annular shaft kiln as developed by Mr. Karl Beckenbach of West Germany. The first&apos; operating unit was rated 185 tons per day and was installed in 1962. Today, there are approximately 84 units in operation in Western Europe and Japan. Twenty-one additional units are in the process of erection or on order. Developed sizes range from approximately 100 to 330 tons per day. Units of over 500 tons are in the design stage, however, the largest units presently operating are rated 330 tons per day, <the first: of this size having been installed in 1966. "Figure" 1 is an elevation view of the unit. It is a single vertical cylinder to which are attached the required service platforms, combustion chambers, injectors and distribution piping. Auxiliaries such as recuperator, exhaust fan and dust collector are mounted on the appropriate service platform. The charging pan, feed conveyor, etc. are mounted at the kiln top. At the bottom of the kiln is the silo with a vibrator type discharger, and mounted separately is the required blower for injector air and fan for internal cooling.

Jan 1, 1973

By Herman Gill, Dani Delaloye, Madelyn Rubin

The Foothill Tunnel is a remote 16-mile-long untreated drinking water tunnel in the San Francisco Public Utilities Commission’s (SFPUC) Hetch Hetchy Water and Power (HHWP) system. The 14-foot horseshoe shaped tunnel, constructed in the 1920s, is lined intermittently with concrete over approximately 53% of its length, with the balance being unlined rock. After detailed planning, in January of 2020 Mott MacDonald and HHWP staff completed a visual inspection and documented the condition of the tunnel with electronic data collection, photographs, and video with audio recording. The result was a comprehensive condition assessment that identified key areas of the tunnel to monitor.

Jun 13, 2021

By D. L. McCain

The movement of solids by pipeline is an art dating back well over 100 years as evidenced by many references in the literature. Even though all of the early pipeline transport systems were based on trial and error and relied mainly upon the designer&apos;s experience, hydraulic transport offered distinct advantages in convenience or cost for the chemical, mining, and civil engineering industries. It became well established for in-plant process lines, dredging, waste disposal, and other uses almost exclusively for short distances. During more recent times, much research work has been done in an attempt to understand the underlying principles involved in transporting solids in a fluid. Design criteria for pumping slurries have evolved to the point where pipelines designed for distances of several miles to several hundred miles can be accomplished successfully. Consolidation Coal Company designed and built a 10-inch diameter 108-mile long line1 for transporting coal in the 1950&apos;s and operated it from 1957 to 1963 when it was placed in mothballs because of falling freight rates for rail shipment. More recently, the 273-mile Black Mesa Pipeline2 was built and is operating. There are other examples of long distance pipelines,3 but all are for specially prepared fine slurries which allow the pipeline to be operated more economically.

Jan 1, 1975

By Sally Gillies

During the 14 years since the last update to National Instrument 43-101 (NI 43-101), there have been many discussions between Canadian regulators and mining companies about mining disclosure deficiencies that arise from regulatory reviews. These discussions are not made public, and as a result, there has been some drift in how NI 43-101 is interpreted by the regulators, which in turn creates uncertainty for the mining companies trying to comply with the instrument. To reduce uncertainty in mining disclosure requirements, the Canadian Securities Administrators (CSA) has issued a notice to update the current NI 43-101 with a streamlined instrument and form. Changes and benefits are listed in the “CSA Notice and Request for Comment — Proposed Repeal and Replacement of National Instrument 43-101 Standards of Disclosure for Mineral Projects,” which is available on the Ontario, Quebec, Alberta and British Columbia Securities Commission websites. The public has been invited to comment, with the comment period ending on Oct. 10, 2025. The 43-101 Companion Policy (43-101 CP) provides an update to the views of the regulators on how the CSA staff interpret and apply certain provisions of the instrument. Collectively, some of the changes to NI 43-101, the form and 43-101 CP are likely to increase the financial and other burdens on the mining companies responsible for the disclosure, and the qualified persons (QPs) who create the disclosure. In other instances, there are missed opportunities to reduce the burden on mining companies and QPs without impacting the markets.

Sep 1, 2025