Search Documents

By J. A. MacLellan

It is the hope of the author that this paper, largely a compilation of observations and opinions built up over 20 years of experience in cold and remote areas may be of some help to others in designing better plants for the future in the north. The north is not as difficult to operate in as the better story tellers make it appear to be. ()n the other hand for 6 months of the year the cold is always there, and it seems to be waiting for someone to make a mistake. The simplest things can shut a multi-million dollar plant down at -4n' F with a 4n M.P.H, wind. It only takes one man door improperly latched to freeze up all the pumps on the bottom floor. Someone can poke a one inch hole in an outside wall in July and six months later while you are having Christmas dinner, a watchman will call up to report that the whole plant is flooded because the main water line just froze up and burst. Basic things to remember in plant design for cold and remote areas are: everything in these areas is more expensive due to long and difficult supply lines. Fuel is expensive and would be a major cost item even if it were not expensive, due to the extended periods of low temperatures. Building volumes should therefore he kept to an acceptable minimum. Service areas on the other hand must he adequate, because maintenance generally has to be conducted inside in a heated area. Supply vehicles for instance have to get completely inside the building to unload. If you try to unload a supply vehicle with the door open at -50° F, you won't be able to find the vehicle for fog and if you take more than 5 minutes half the water lines in the plant will freeze up. People in a remote area are expensive. The capital investment per employee may be as high as $30,000; with fringe benefits per annum costs of an employee will he as high as 812,000 per year regardless of basic wage rate. It

Jan 1, 1971

By Hugh Douglas

This paper discusses the financial health of the U.S. mining industry and its ability to meet the future raw material requirements of this country in the context of resource independence. The title of this paper begs several questions, and three will be raised here. The answers to them will form the basis for discussion. The three questions are: What does one mean by resource independence. How is the U.S. mining industry defined. How is financial health measured.

Jan 1, 1977

By L. Alagha, L. A. Sanchez-Calderon

The existing methods for recycling lithium-ion batteries present initial hurdles related to the safe handling and preparation of the batteries to avert potential explosions. Submerging batteries in sodium chloride (NaCl) solution has become an acceptable industrial practice. However, the use of NaCl to discharge lithium-ion batteries rusts the batteries’ cases and releases metals which impacts the downstream processes that involve selective recovery of Li. This study aimed to determine the optimal concentrations and pH range of NaCl for the discharge of lithium-ion batteries for the purpose of minimizing the leach of Al, Co, Cu, Fe, Li, and Ni.

Feb 1, 2024

By F. G. Schora

The Institute of Gas Technology (IGT), under sponsorship of the U. S. Department of the Interior, Office of Coal Research (OCR), and the American Gas Association (A. G. A. ), has been undertaking the development of one of several processes to convert coal to high-Btu gas as a means of supplementing natural gas supplies. It is anticipated that there will be a significant need for such gas in the foreseeable future in order to meet the ever increasing demands for this preferred fuel form. HISTORY The development of the HYGAS® Process is based on various studies conducted at IGT starting back as far as 1945. Initial work was directed toward production of synthesis gas with subsequent catalytic methanation. By 1964 the concept of the direct hydrogenation of coal to produce methane noncatalytically was well-founded and the chemistry was reasonably well established. Work up until this point in time was financed by the American Gas Association. In 1964 the U. S. Department of the Interior, Office of Coal Research joined with A. G. A. to support the program. The objective at that time was to develop the necessary know-how to enable the design of a pilot plant, a necessary step in the ultimate commercialization of the process. Work for the next three years (1964-1967) emphasized investigation of fluidized-bed technology in the hydrogasification step, where moving-bed technology had been previously employed, as well as identification of commercially available catalysts acceptable for catalytic methanation of the CO and hydrogen in the hydrogasifier effluent under operating conditions in the system. By 1967, the preliminary design of a 3 ton/hr pilot plant had been finalized, and IGT received authorization from OCR to proceed with the detailed design and construction of that facility. The pilot plant was designed to study the following problems:

Jan 1, 1972

By Juan Andres Jarufe, Carlos Cifuentes

Numerical modelling has been extensively used to estimate plastic displacement in faults and rock mass surrounding mine excavations. Particularly, for fault slip seismicity, modelled plastic displacement is usually utilized to estimate seismic potential, however these methods assume that all the displacement caused during an specific simulated excavation step, is released as a single event at each step. This representation corresponds to a conservative estimation since rock mass displacement does not occur as one single event but as an exponential distribution of many small displacements and a few large ones. When displacement is expressed as seismic magnitude, this exponential distribution is addressed as the Gutenberg Richter (GR) relationship. This paper present a method to decompose the results from numerical models into a distribution of seismic events The reconstruction of the GR relationship from modelling displacement permits not only a more realistic approximation of the expected maximum magnitudes but also provides a tool to develop a probabilistic estimation of the maximum possible magnitudes.

Apr 26, 2022

By C. Nesbit, N. Duru

During the cyanide leaching process of gold and silver, ores that come from the transition zones which typically con-tains low levels of sulfide may produce one or more of the following reduced sulfur species: sulfide (HS ), polysulfides (Sn ), thiocyanate (SCN ), thiosulfate (S2O3 ), trithionate (S3O6 ), tetrathionate (S4O6 ), pentathionate (S5O6 ) and hexathionate (S6O6 ). The actual speciation of the reduced sulfur species in the circuits will primarily depend on the re-dox potential, pH, cyanide levels and existing sulfur species in recycled process water, as well as the presence of other reac-tive metal species. Development of an accurate analytical method for sul-fur species in cyanide leaching units of gold ores where sul-fur speciation occurs has an important role in explaining the metal recovery deviations. This study presents the speciation of sulfur species and development of an ion chromatography method to analyze the reduced sulfur species thiocyanate, thio-sulfate, trithionate and tetrathionate in cyanide leaching circuits for gold ores. The method developed has resulted in the precise quantification of target sulfur species in leach solutions.

Jun 1, 2024

By C. J. Milam

Oil shale may not produce the same excitement of the gold rush days, but presently there is an "oil shale fever" among mining men. Such exotic equipment as 800-ton haul units, 75 ft. boring machines, and huge fully automatic multi-purpose jumbo drill units are only a few of the topics of conversation in the oil shale groups. I am dreaming, perhaps, but this type of exotic thinking will exuberate the advancement in mining technology and will only be tempered by the practicality and the availability of today's equipment.

Jan 1, 1975

By O. P. Burghardt

Blast furnaces of high specific throughput capacities producing 10,000 tpd of pig iron or even more, require burden materials which, because of their chemical, physical and metallurgical properties, guarantee such high performances. Meanwhile, it should be generally accepted that for evaluating the quality of iron ore pellets, it is not sufficient to know the chemical analysis and the physical properties, i.e. grain size distribution, cold compression strength and abrasion of the fired pellets. It is indispensable to determine the metallurgical properties indicated by swelling, reduction-softening under load and reducibility, as well as grain disintegration in the low-temperature range in the beginning of reduction. By introducing new test methods, and in the face of the need to meet more strict requirements, pellet producers are being confronted with steadily increasing tasks and problems which require a deepening of our knowledge of the ways and means of making high-quality iron ore pellets.

Jan 1, 1975

By S. D. F. Rocha, A. L. A. SANTOS, E. M. A. BECHELENI, F. P. C. Silvas

Hydrometallurgical processes are needed to extract nickel (Ni) when it is disseminated in mineral matrix. High-pressure acid leaching (HPAL) and atmospheric acid leaching (AAL) are alternatives, and AAL has the advantage of requiring mild temperatures and pressure. Reducing-reagent tests improved the extraction of metals for the specific limiting portion of the ore. Low dosage of sodium thiosulfate presented better selectivity and safer operating conditions, allowing metal extractions of 50–62 percent at 95 °C. However, the low extraction rate obtained for Ni and the similar levels of impurities — magnesium (Mg), manganese (Mn), cobalt (Co) and iron (Fe) — extracted may represent economical and technological challenges in the downstream process.

By John F. M. Sims

Political issues and a glaring infrastructure deficiency have retarded the emergence of a strong mining component to the Alaskan economy in recent years. Barriers to orderly mineral development are slowly being removed attendant upon changing political circumstances. Infrastructure development, as an investment avenue as well as a responsibility of the State, is receiving much greater attention than in the past. Alaska of course has a rich and varied mining history going back to the 19th Century. This paper, however, focuses on the mining potential, not the mining heritage of the 49th State. The mining industry is emerging from a nadir in the economic cycle - times during which it was buffeted by unsympathetic administrations and confused and confounded by the protracted land status- conflicts prior to enactment; of the Alaska National Interest Lands Conservation Act (ANILCA) and other milestone legislation. Today Alaska's mining industry looks toward a bright and healthy future and, in the process, will become a very important and vital component of the State and national economy.

Jan 1, 1982

By Neil D. Policow

Dewatering of the fine clean coal fraction, - 28 mesh (595 microns) represents one of the most difficult and costly separations in typical plant circuits. Since 1969, the Screen Bowl Centrifuge has offered an economical alternative to filtration/thermal dryer combinations. The performance of Screen Bowl Centrifuges has been continuously modified and improved to dewater not only coarser coals, but also today's variety of ultrafine material. Actual test comparisons with alternative methods show the Screen Bowl Centrifuge to be most cost effective and efficient when all factors are considered.

Jan 1, 1982

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By V. P. Petrov

There is a great number of asbestos deposits in the USSR. Some of them are quite large ones. The main deposits of chrysotile asbestos can be seen in the sketch map (fig. 1). Bazhenovo deposit situated in Sverdlovsk region is the largest of them. It is on mining operations since year 1889. Systematical studies of asbestos deposits were begun from the first years of Soviet Government and connected with the names of K.E. Tarasov, P. M. Tatarinov, B. J. Merenkov, N.D. Sobolev, F. V. Syromjatnikov, V. N. Lodochnikov, V.P. Petrov, V.P. Eremeev, L.A. Sokolova, V. R. Artemov, V.F. Dybkov and many others. This investigations served the USSR to be one of the most important producers of asbestos in the world. In the limits of the report a characteristic of the main asbestos deposits of the USSR may be done in general outline, from the point of view of their genesis, and in order to show their common features and differences that must be taken into account for forecasting, exploration, and mining of asbestos. All chrysotile asbestos deposits of the USSR were formed of magnesium rock as a result of comparatively lower-grade temperature hydrothermal alteration and free crystallization of fibrous chrysotile in open cavities that served as catalyst As a matter of fact an important mineral for industry is not chrysotile in general, a widely distributed rock-forming mineral, but a long fibrous and mainly vein variety of chrysotile. It must serve for geologists as an important prospecting criteria. A geologist should search for the mineral not only places of possible chrysotile generations, but places where asbestos may be crystallized in its long fibers that could be fiberized well. The Soviet geologists distinguish two groups of chrysotile-asbestos deposits: (1) related to ultrabasic rocks and (2) related to sedimentary dolomite terranes, taking into account what the maternal rock was affected by hydrothermal solutions. The largest deposits related to ultrabasite. The largest deposits in dolomite are small ones but their asbestos contains almost no iron. So much asbestos is a better filler into insulating plastics. There is a few types of asbestos deposits in the limits of the ultrabasic group. The largest of them is a Bazhenovo type which the deposits of Urals are attributed, and Bazhenovo deposits is the first instance. The Bazhenovo type is characterized by the most complete zonality in disposition of various kinds of asbestization. This type of deposits is practically the only one to be in working now in the USSR.

Jan 1, 1978

By Zengwu Zhao, Peng Xu, Jieliang Wang, Qingwei Bai, Xinyang Liu, Xiao Lei

The paper investigates the capture and recovery of rare earth minerals from Bayan Obo ore using superconducting magnetic separation. A finite element model (FEM) was established to study the influence of various factors on the capture of rare earth minerals under a high-gradient superconducting magnetic field. The study aims to improve the efficiency of rare earth mineral separation and recovery.

Oct 1, 2023

By Ginger L. Hustrulid

Conveyor belts are a critical component in tunneling projects. This paper reviews current design considerations for conveyor belts. Rubber compounding differences to meet local fire resistance regulations or certain cover characteristics such as higher abrasion resistance or low carbon footprint rubbers for applications are reviewed. Evaluation of fabric belts, steel cable belts and the benefits of each carcass design for a particular use is also examined to help with proper carcass selection to decrease downtime from unexpected failures. Finally, this paper takes a look at some of the differences when working in metric versus imperial units.

Dec 1, 2022

By Georges Cote, Ehsan Alavi, Eren Kusdogan

The City of Toronto's Coxwell Bypass Tunnel is currently being constructed by North Tunnel Constructors (NTC) ULC, a joint venture of Jay Dee Canada, C&M McNally Tunnel Constructors and Michels Canada. This project includes construction of approximately 10.5 km of 6.3 meter finished diameter rock tunnel, five 20 meter diameter storage shafts and eleven tunnel connection drop shafts, along with associated deaeration and adit tunnels. 120 m of Starter tunnel and 70 m of Tail tunnel were excavated with roadheaders to help with the launch of the TBM and as part of the contract base scope work. JayDee Canada in Collaboration with Everest Equipment Co. developed an innovative approach to design and build a stand-alone Ring Machine Erector nicknamed Enterprise to erect precast segmental lining in Starter and Tail tunnels in lieu of Cast-In- Place concrete. This paper describes the design and provides feedback on the innovative procedure used to install the rings.

Jun 23, 2024

By Kirk Carlton

The Athabasca tar sands of Alberta are an increasingly important source of crude oil for the North American continent. Published figures indicate estimates of recoverable resources in the tar sands at some 300 billion barrels of synthetic crude of which some 86 billion barrels can be recovered by surface mining techniques. At the present time, two commercial plants are in operation, Great Canadian Oil Sands Limited and Syncrude Canada Ltd. Their present combined capacity is approximately 150,000 barrels per day. Some of the factors which will make this oil expensive will be noted here. The location of the present producing plants is 500 kilometres north of Edmonton at an elevation of approximately 320 metres. Recorded temperatures range from +38 to -55 degrees Celsius. Wind velocities are not high but the chill factor with even a slight breeze and minus 40 degrees is very uncomfortable.

Jan 1, 1979

By Debra Switzer, Swapnil Urankar, Douglas Watson, Steven Hunter, Chandranth Banerjee, Shashank Pathak

A hydrocyclone is a piece of equipment commonly used as a classifier in mill circuit operations. Traditionally, hydrocyclone performance is characterized by the classification efficiency parameter, such as cut size (d50c), sharpness of separation () and bypass (Rf ). A plethora of endeavors have already been made to develop parametric models to determine hydrocyclone performance that correlate design and process variables. In contrast to those studies, we made an attempt to develop an approach to derive required design parameters purely from hydrodynamic principles that provides a platform to optimize the operation of a hydrocyclone for a given application. In this selection methodology, we calculated the differential pressure at the air core, as well as the tangential velocity at the boundary of the air core from the vortex principle in a confined geometry at different operating regimes. A series of experiments were conducted using Weir’s Cavex® hydrocylone where process variables—such as solids concentration and feed flowrates—were experimentally studied to determine the key classification parameters. For the validation of the current approach we used the same process variables to derive design parameters and compared them with the existing design. The current approach can provide insights towards the selection of design parameters and can be useful for mining industry professionals to optimize different operating parameters of hydrocyclones to achieve the best performance.

Feb 1, 2024

By James K. Kindig

Hazen Research, Inc., has developed a new process for removing pyritic sulfur and ash from coal. Feed coal is contacted with iron carbonyl vapors, Fe(CO)5, at 190°C which puts a thin skin of magnetic material on the pyrite and ash, but does not affect the coal. Thus, low intensity magnetic separators yield a nonmagnetic coal, low in sulfur and ash, and a magnetic refuse, high in sulfur and ash. Results are given for clean coal produced by this method. A comparison is made between results of the magnetic process and the U. S. Bureau of Mines two-stage flotation process cleaning identical samples of Pittsburgh Coal. Capital and operating costs of the two cleaning methods are discussed.

Jan 1, 1976

By Anand Kumar, Debasis Deb, A. K. Mishra, M V. N. S. PRASAD.

In the Adriyala project, shield-leg pressure data from all shields and shearer location with time stamp from a mechanized longwall face are monitored and recorded in a surface computer. The data contain random noise due to power failure, leakage of legs, bad sensor readings, and other maintenance or geomechanical problems. An algorithm has been developed to detect mining cycle parameters such as setting and final pressures and duration of the cycle from these data for the analysis of periodic roof weighting phenomena. The intensities and persistence of periodic roof weighting are vital information for mine management to make judicious decisions on longwall operation.