Search Documents

By SAMUEL A. LOLON, ADITYA JUGANDA, JURGEN F. BRUNE, JR. GREGORY E. BOGIN

Historically, there have been many events of mine fires and explosions recorded in the United States and other countries that have demonstrated the existence of explosive methane-air mixtures, herein referred to as explosive gas zones (EGZs) [1]. The risk of mine explosions can increase if these EGZs migrate out from the gob into the surrounding mine entries — a phenomenon known as gob breathing. A number of 3D computational fluid dynamics (CFD) simulations using various magnitudes and periods of barometric pressure variation have indicated that the EGZ outgassing potentially occurs due to lags in pressure, which are strongly influenced by mine conditions and ventilation systems. Early-warning systems with real-time pressure monitoring and the application of gob ventilation boreholes are recommended to detect and mitigate explosion hazards from gob outgassing.

By Thomas P. Meloy

Comminution is an old art. Unfortunately the analysis of the unit operations has been handicapped by the lack of both theoretical and experimental information. Two types of infor¬mation are needed, one an understanding of what happens when a particle breaks in a brittle manner; and two, an understanding of what happens when the daughter fragments pass through the mill. This paper is concerned with the former, the catastrophic fracture of a brittle solid. Recently, successful theoretical attacks on the frac¬ture of brittle solids have yielded significant-results. New experimental techniques are yielding insight into the physical phenomenon occurring during brittle fracture. Many of the re¬doubtable shiboliths of the last century are either being laid to rest or verified.

Jan 1, 1965

By C. C. Harvey

Based on resource studies in many developing countries, four categories of industrial clay resources are recognized as precursors to development strategies. Category I: High quality, high technology clays requiring major investment for large tonnage international markets. Category 2: Unique specialty clays requiring advanced technologies for small tonnage niche markets. Category 3: Lower technology, moderate quality clays, predominantly to supply local markets. Category 4: Low quality clays requiring little or no processing. Projects with Categories 1 and 2 clays require extended development times (green field to investment decisions) with significant pre-development investment, while projects with Categories 3 and 4 clays require shorter development timetables and lower levels of investment.

Jan 1, 1998

By L. Yuan, J. H. Rowland, R. A. Thomas

Hydrogen (H2 ) gas released during battery charging can result in cross-interference for carbon monoxide (CO) sensors used for early fire detection and compromise the integrity of the mine atmospheric monitoring system. In this study, a series of laboratory-scale and full-scale experiments were conducted to evaluate the responses of different CO sensors to H2 gas. In the laboratory-scale experiments, H2 concentrations in the airflow are constant, while in the full-scale experiments, increasing H2 concentrations generated as a byproduct of charging the batteries at the battery charging station rise to the sensors under different ventilation scenarios. The H2 concentrations at the CO sensor location were measured using H2 sensors and were correlated with the CO sensor response. The effects of ventilation and sensor location on the CO sensors responses were also analyzed. The results of this study can help mining companies to select appropriate CO sensors and improve the deployment of these sensors to safeguard underground miners.

By Lisa Shevenell

Three pits at the Getchell Mine contained water during a hiatus in mining activity (1968-1983). For this period, expected concentrations of As, C1, SO4 and TDS resulting solely 16om evaporative concentration were computed. Computed values are 1.6 to 2.3 times greater than those measured in local groundwaters. However, computed values fix As, SO4 and TDS are lower than measured values in the pit lakes. In some cases, the computed values are only 8% of the measured pit lake values, indicating a major control on water quality via water-rock interactions. In contrast, computed C1 values exceed measured pit lake concentrations.

Jan 1, 2000

By Qiu Rongqing, Huang Kongxuan

This paper summarizes the results of treating arsenic­bearing refractory gold concentrates from six gold Mines of Chi­na by using bioleaching method and discusses the conditions of bioleaching processes. Results indicate that Thiobacillus fer­rooxidans T-3 Strain can intensely oxidize arsenopyrite, how­ever oxidation rate and degree differe considerably for different. During initial inoculation of 5 X 106 cell/ml. FeH contration generaly 4 -8 g/1. Sample size > 80 % - 3 20 mesh and pulp density 10 % ( w /v) and leaching time ,1 -- G clays, arsenic re­moval rate reached more than 80 % , Fe extraction ,10 - GO% desulfurization rate 30-45% after bacterial oxidation of 4-G days.

Jan 1, 1992

By A. D. Davis

Naturally occurring arsenic has been detected in water from inactive mines and several wells in the Keystone area of the Black Hills. Keystone City Well #4 showed a total arsenic concentration of 69 parts per billion (ppb) during pumping in 2004. The well is not used currently except for arsenic-removal research. Water also can be pumped from a mine shaft in the abandoned Keystone ? Columbia ? Bullion gold mines, whose interconnected workings flooded after mining ceased in the 1930s. This water has been considered for local supplies, although it would require treatment or blending because of arsenic concentrations. According to historical records, the Bullion Mine produced 100,000 pounds of white arsenic. An aquifer test on the mine workings was performed at a pumping rate of about 550 gallons per minute. The arsenic concentration in pumped water was 33 ppb. In addition to wells within Keystone, samples from the water supply at nearby Mount Rushmore National Memorial have shown arsenic concentrations greater than 10 ppb, the U.S. Environmental Protection Agency?s maximum contaminant level for arsenic in drinking water. Limestone-based technology for removal of arsenic from drinking water is an innovative and promising method that has been considered for treatment of water at Keystone. In batch testing with water from Keystone Well #4, limestone removed about 65% of arsenic from solution. A related problem of arsenic removal from drinking water involves disposal of the waste product, which is critical for commercial viability of removal technologies. Current research is investigating thermal stability of the waste in order to determine the potential for recycling of the material during manufacture of cement.

Jan 1, 2010

By P. K. Kaiser, M. Cai

When designing an efficient and effective support system for burst-prone ground, it necessary to select the most appropriate, i.e., the ‘right’ support components, including areal and reinforcement components. For this paper, it is assumed that the areal support is not the weakest link and the support performance is controlled by the rock reinforcement and holding components (bolts). We discuss the loading modes of rockbolts under static and dynamic loadings and analyze published data from laboratory and field tests. The mechanisms of energy absorption of dynamic rockbolts are presented and rockbolts are categorized based on factors such as energy absorption capacity, energy absorption rate, direct and indirect energy absorption capacities, rock mass bulking or displacement control, and shearing resistance capacity. Guidelines for selecting the ‘right’ rockbolts to build an effective rock support system for burst-prone ground are provided.

Apr 26, 2022

By David R. Hargis

Large-scale groundwater withdrawals are necessary to depressurize a confined aquifer system allowing the dry open-pit mining of the overlying phosphate ore. The extent of the existing and planned groundwater development led to the establishment by the State of North Carolina of Capacity Use Area No. l. Groundwater use in the Capacity Use Area is regulated by a permitting system. A two-dimensional finite-difference ground- water flow model was developed for North Carolina Phosphate Corporation. The aim of the model is to aid the Corporation in matters relating to permitting by serving as a predictive tool. The model can be used to project regional water level impacts resulting from various scenarios of depressurization pumping.

Jan 1, 1983

By L. R. McCullough

To compete in Today's Market, Mine Managers have two, often conflicting tasks. They are to improve productivity, allowing the mines to compete in our world markets and to improve the environment in which our miners must work. To Maintain and improve the environment to ever increasing acceptable levels requires monitoring. In years passed this required considerable labor, which was provided by the Ventilation Department. They continuously took manual samples using hand-held instruments, sampling gas level such as CO for fire and methane for explosive risks. In addition they took continuous air velocity readings with hand-held instruments which allow them to calculate the ventilation air movement in each area of the Mine. This manual gathering of information was not only expensive and slow but marginal at best. It was marginal because the gas sampling was sporadic rather than continuous, as sample reading taken in one part of the mine would likely not be repeated for another 8 hours. If problems did occur, they likely went unobserved until they reached crisis proportion.

Jan 1, 1990

By William R. Bush

This paper is a presentation of findings based upon an econometric model of the world zinc industry. The model was developed as a simple but useful aid for long-run forecasting and planning purposes. A structure was developed for both simulating real zinc price effects on production and consumption, and for forecasting long-run annual zinc prices and supply/ demand levels. Moreover, a methodology is provided to incorporate the effects of: (1) historic technological advances in zinc supply, and (2) the development of the competitive plastics industry. Finally, reduced form equations are used to generate ex post forecasts to evaluate the model's performance.

Jan 1, 1979

By Robert M. Stevens

INTRODUCTION Truck haulage of muck in underground mining operations has been in use around the world for many years. From the late 1.950s into the early 1970s, haulage by means of load-haul-dump (LHD) units challenged haulage by means of trucks, and, to a large degree, LHD units dominated the trackless concept of moving mate¬rial underground. However, beginning in 1975, the emphasis began to shift back to the use of trucks, with LHD units assuming the secondary role of loading the trucks. Over the years, several manufacturers have been offering trucks with capacities ranging from 4.5 to 45.4 t (5 to 50 st) and with features that specifically address the constraints of underground operation. TRUCK TYPES Three different types of trucks are available for use underground, namely the tip dumpers, telescoping dumpers, and push-plate dumpers. The following para¬graphs describe each of these three types. Tip Dumpers Tip dumpers are designed to lift the truck box, using gravity to dump the load out the rear of the box. The primary application of these trucks is in the haulage of muck to the surface. However, these trucks also may be utilized underground, if a chamber is provided to accommodate the raised truck box at the dumping point. Fig. 1 illustrates a four-wheel drive truck with a 10.0-t (11-st) capacity; this truck is only 1.9 m (6.25 ft) wide and is designed specifically to follow narrow and winding vein courses. Fig. 2 illustrates a two-wheel drive tip dumper with a 24.5-t (27-st) capacity; this truck operates on 12% grades with firm dry surfaces and in modes both loaded-up and loaded¬down. Telescoping Dumpers Telescoping dumpers specifically address the constraints imposed by low back heights, and they represent an optimization of compressed envelope size with maximum payload capacity. Figs. 3 and 4 illus¬trate a typical telescoping dumper with a capacity of 18.1 t (20 st). Fig. 3 shows the box in position for carrying the load, and Fig. 4 shows the same truck with the box in the full-dumping position. Fig. 5 illustrates the loading and dumping cycles. Fig. 6 illustrates an approximation of how an LHD unit with an eject-o-dump (EOD) bucket would be used to load over the rear of this type of truck. Fig. 6 shows a low-profile telescoping truck in the first stage of loading, with a 6.8-t (7.5-st) LHD unit equipped with an EOD bucket. A loader with a smaller capacity and a narrower bucket would allow the bucket to fit inside the truck box and would achieve an even lower loading height than that illustrated. Gen erally, an LHD unit equipped with an EOD bucket and teamed with a telescoping dump truck can be used with a lower back height than could any other front-end loader and truck team. Push-Plate Dumpers Push-plate dumpers are similar to telescoping Bump¬ers, except that they do not have the two-stage box. Instead, push-plate dumpers utilize a single push plate to discharge the load out the rear of the box. Gen erally, these units are limited to payload capacities of about 9 t (10 st). Fig. 7 illustrates a typical push-plate dumper.

Jan 1, 1982

By Walter C. Labys

This paper reports on recent modeling efforts to analyze the eastern U.S. steam coal market with a cross-sectional econometric as well as a quadratic programming approach. The background to coal modeling is examined first. The particular aspect of the steam coal market to be modeled are then presented and the corresponding coal model described. Both empirical results and rigorous mathematic pertubation analysis are presented. Conclusions are then drawn regarding potential modeling applications in the policy area.

Jan 1, 1979

By CHONG WEI, TATYANA KATSAGA, DEREK APEL

This study provides an effective determination process of the interface microstructural parameters in the numerical modeling of the mechanical interaction between two different geomaterials involved with frictional-bonded interfaces, such as the interaction between backfill columns and the surrounding rocks, or the soil-structure interaction, by using the coupled finite-difference and discrete-element (FD-DE) method. The test results validated the feasibility and rationality of the coupled FD-DE method for modeling the combined specimens with frictional-bonded interfaces or joints. Furthermore, this study provides valuable numerical modeling experience for investigating the shear behavior at the interface between cemented backfill columns and surrounding walls by using the coupled FD-DE method.

By Panshi Xie, Xicai Gao, Yi Luo, Youfu Zeng, Yongping Wu, Shenghu Luo

For the first time, surface subsidence prediction theory was used to investigate roof movement around longwall face mining in a steeply dipping coal seam. A physical simulation experiment was conducted to quantitatively study the roof migration patterns, the gob materials, and the characteristics of bed separation and compression caused by mining two adjacent panels to gain a better understanding of ground control issues in multipanel mining in steeply dipping seam. This approach provides an in-depth analysis of the movement of the roof. Compared to movement observation of survey point using total station, the Photogrammetry Analysis for Physical Modeling of Mine Subsidence Program (PAPMMSP) method is easier to perform, faster and yields the much higher accuracy required for scale physical modeling. It is also a more effective observation method for underground-mining physical simulation experiments.

By Smart Chika Obiora, Anthony Chukwu

Lead and zinc have been mined for over 90 years in parts of the Lower Benue rift in southeastern Nigeria. However, there has been little interest in the sustainability of the environment and the inhabitants of the host communities. Adverse effects include soil and food crop contamination, lack of education, poor healthcare, unemployment, and no access to potable water. This work suggests practicable mitigation strategies to ameliorate these negative effects and promote environmental sustainability.

Jul 1, 2023

By R. L. Weigel

As Florida phosphate mining gradually moves from the Bone Valley formation to the Hawthorn formation, a greater portion of the minable deposit contains dolomitic diluents which result in lower product grades that can be detrimental to the production of phosphoric acid for fertilizer uses. One beneficiation technique found applicable to the phosphate pebble size range (3 X 16 mesh) is heavy media separation using suspensions of magnetite and ferrosilicon. As part of an ongoing investigation of dolomite removal technology, a pilot heavy media cyclone system was constructed by IMC and used in the testing of a variety of drill core composites and hulk samples. The results of these tests were used to develop a predictive model for heavy media cyclone separation based on pebble fraction assays and heavy media operating parameters. This model is currently being used in the evaluation of specific future mining areas.

Jan 1, 1984

By A. T. Yu

Technology and economies of scale have, in the past decade, brought about the emergence of giant vessels. Meanwhile, to answer the need for rapid dispatch, as a means of combating the proportionately far greater demurrage charges, shiploading and unloading speeds have soared (Ref. 1, 2, 3). As the loading and unloading rates have dramatically increased, so has the cloud of dust grown in unbearable proportions. It not only has threatened to be a real menace to machinery and men, but in certain instances has also seriously jeopardized fish and marine life (Ref. 4). In an era when ecology is king, dust in shiploading and unloading can no longer be shrugged off as a mere public nuisance, and its control is now duly recognized as of grave concern to all. Even if public outcry were not a problem, from the operator's own parochial point of view, dust can adversely affect productivity and the well-being of the operating personnel. Without adequate control, it can also result in costly equipment maintenance, particularly when the dust is micronic in size, and abrasive. The Hierarchy of Control Techniques Given the great fortune of not yet having to deal with gas and odors, in the jargon of pollution control, our problem is confined to having to control "particulates" only. To deal with "particulates", the myriad of dust control techniques can be utterly confusing to those who are not entirely well versed in the methodology. Our analysis of what is available to date results in the following hierarchy of logical preferences: 1. Prevention 2. Removal 3. Suppression 4. Containment 5. Dilution Since it deals with the root cause, prevention always outranks the cure. Once the dust is generated, removal nips it in the bud. Only when dust removal is

Jan 1, 1972

By Maria S. Adusmilli, Bhaskara A. Rao, Jorge G. C. Barros, Augusto F. Mendonca

Lateritic gold has been the object of study only for a very few years, though nuggets have been mentioned in earlier works even as early as 1984 by Hartt in Brazil. In Mato Grosso State, lateritisation is intense, as is common in all tropical forest areas of the world. Exploration has revealed the presence of recoverable "nugget gold" of variable sizes (30 - 200 gms) but frequently of good size (0 - 40 gms), especially near Cuiaba and Alta Floresta regions. In both of them the host system is a lateritised breccia indicative of a fault or shear zone breccia, though in different lithological domains. The Cuiaba occurrences are phyllitic and show a profile as follows, from top to bottom: 1) Compact ferralite crust. 2) Oolitic to pisolitic compact crust (+ some gold). 3) Mottled concretionary laterite crust. 4) Lateritised "eluvial material" (gold nuggets). 5) Mottled patchy to banded laterite. 6) Banded lateritised phyllite with lenticular to banded goethite. 7) Altered red goethitic phyllite, with quartz veins (+ fine gold). 8) Unaltered grey phyllite with quartz veins (Protore). The Alta Floresta-Juruena River occurrences are volcano-sedimentary and show a profile as follows: 1) Deep brown siltitic, argillaceous and arenaceous material with organic matter (+ gold). 2) Modular and concretionary laterite, compact and indurated, with arsenophyrite in quartz fragments (gold nuggets). 3) Band with silty-clayey matrix and arenaceous in nature. 4) Bedrock meta-arcosian arenite. 5) Volcano-sedimentary with rhyodacites and andesitic basalts, with intercalations of arkosic and greywacke nature. Breccias and quartz veins, and granites associated in different portions (Protore).

Jan 1, 1988

By Timothy P. Smirnoff, Arthur P. Chase, Herman J. Smith

INTRODUCTION The Newtown Creek Pollution Control Project (P.W. 53) is a major system of facilities designed to collect wastewater from large areas of the Boroughs of Manhattan, Brooklyn and Queens, then channel it to a treatment plant where the wastewater is processed and discharged. The North Branch interceptor collects wastewater along the east side of Manhattan and transports it downstream to a Junction Chamber at Avenue "D" near East 13th Street. The South Branch interceptor similarly collects wastewater from the southern part of Manhattan Island on both east and west sides of Manhattan and transports it to the same Junction Chamber from where both flows are delivered to the adjacent Manhattan Pumping Station which pumps the wastewater under the East River to a treatment plant in Brooklyn. This system is shown in Figure 1. Construction of the Manhattan Pumping Station began in the Summer of 1966 and was delayed by a number of mishaps. In the vicinity of the North and South Interceptors, approximately 3,060 cubic meters (4,000 cubic yards) of soil flowed into the excavation: 765 cubic meters (1,000 cubic yards) at the North Branch Interceptor, and approximately 2,300 cubic meters (3,000 cubic yards) at the South Interceptor. These movements were accompanied by surface subsidence, collapse, or both. On June 4, 1973, while pumping station construction was underway, approximately five to seven cubic yards of sand entered the junction chamber through a temporary bulkhead valve in the North Branch Interceptor.

Jan 1, 1979