Search Documents

By K. Awuah-Offei

Energy efficiency has become significant due to cost and environmental considerations. Comminution and material handling have been identified as the two most energy intensive processes in mining. The objective of this work was to evaluate truck-shovel energy efficiency strategies using discrete event modeling. Energy audits and time and motion studies were conducted at a surface coal mine to acquire data. A discrete event simulation model of truck-shovel operations was built in Arena® and validated with the field data. The model was used to evaluate the effect of using a larger shovel, and optimizing truck-shovel matching on fuel efficiency. The results indicate that using a larger excavator increases the fuel efficiency of the operation while optimizing truck-shovel matching does not. However, using a larger shovel will lead to under-utilization of the shovel. This work shows the potential benefits of using discrete event simulation to model energy efficiency of mining operations.

Jan 1, 2012

By T. J. Batchler

Deformable materials are sometimes added to ventilation stopping constructions to prevent damage caused by convergence in coal mines. However, adding deformable materials can significantly reduce the capacity of a stopping to resist transverse loading. As part of its mining health and safety program, the National Institute for Occupational Safety and Health (NIOSH) has conducted research on the effect of various materials with different deformation properties on the transverse loading capability of a stopping wall. Based on a three-point hinge method of failure, a half-wall method of testing in the NIOSH Mine Roof Simulator was used to simulate full-scale wall behavior. This simulated the fracture initiation and eventual failure of the stoppings from transverse loading. The impact of the modulus of elasticity of various deformable materials was examined in this study. A polystyrene foam block with a low modulus of elasticity, which is commonly used as a deformable material, was shown to degrade the transverse load capacity of the stopping by as much 95%. Other materials with higher modulus of elasticity preserved more of the transverse load capacity of the stopping, but were not able to absorb as much convergence. This paper presents the results of a parametric study that quantifies the impact of various deformable materials in block stopping construction under transverse load conditions. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By C. Bise, A. Seal

Excessive noise has long been a hazard in the coal-mining industry. Studies conducted during both the mid-1970s and the mid-1990s consistently show that hearing hearing loss within the mining industry persists, in spite of regulatory requirements and sampling technology advances. When MSHA’s new health standards to protect miners from hearing loss took effect in September 2000, the potential developed to re-evaluate sampling approaches with regard to noise-source hazards, such as task-based methods. This paper describes results from a Penn State research project currently being conducted at an underground coal mine. Each occupation was reviewed, and a list of tasks or processes performed by each was generated. Traditional personal noise dosimetry, static sound pressure levels, and equipment sound mappings have been performed. Job tasks indicating the greatest levels of daily noise exposure and contributions to noise dose have been identified and will be discussed.

Jan 1, 2001

By R. E. Chaves

San Martin Mine is an open pit, gold heap leach operation located approximately 70 kilometers from the Honduran capital of Tegucigalpa. Mining operations commenced in 2000 and were completed late in 2007, while heap leaching operations continue. Reclamation was executed concurrently with operations to the extent practical. The area has distinct rainy and dry seasons and closure objectives include: prevention and mitigation of acid rock drainage, sediment and erosion control, and mitigation of visual impacts. Final closure is well underway at San Martin and this paper describes the closure processes conducted to date, problems encountered, and the subsequent lessons learned.

Jan 1, 2009

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

Phelps Dodge Mining’s Bagdad, AZ copper facility uses a large series of cone crushers and ball mills to reduce copper ore to very fine particles. The solids are mixed with water to create a slurry. Milk of lime is added to this slurry to raise the pH. Small amounts of reagents are also added, including a frother to make bubbles, as well as a collector chemical that causes the copper minerals to stick to those bubbles. This material is pumped to a series of froth flotation cells to concentrate the copper. Air is blown into the flotation cell tank and the pulp mixture is vigorously agitated. Rising bubbles carry the copper particles over the edge of the flotation tank. The bubbles break after they flow over the edge.

Jan 1, 2005

By Steve Kral

MINExpo INTERNATIONL 2000 was a good place for companies to introduce new products, technologies and services to the mining industry. Caterpillar took that a step further. The company hosted a one-day preview of its mining products at its Tinaja Hills Training and Demonstration Center near Tucson, AZ. About 30 members of the trade press spent the day at Tinaja Hills before heading on to Las Vegas for MINExpo INTERNATIONAL 2000. Dozens of Caterpillar professionals provided the editors with a first-hand look at Caterpillar’s mining trucks, loaders, excavators, road graders, water trucks and engines. In addition, these Cat experts explained the intricacies of each piece of equipment, the latest technology that led their improvement and their value to the company’s mining customers.

Jan 1, 2000

By Lee W. Abramson

Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on several recently constructed tunnel projects. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed.

By Michelle Stokes, Alexandra Miller, Campbell McKenzie

"The ancestral Ringarooma River in northeast Tasmania has transported alluvial tin and other heavy minerals from their onshore source of stanniferous Devonian granites downstream into what is now Ringarooma Bay. Previous exploration work has demonstrated the presence of potentially economic tin mineralisation within the palaeochannels and terraces associated with the submerged river.The offshore tin resource lies directly on the seabed or with less than 2 m of overburden, and within 5 - 50 m water depths in the wider bay area. The main river channel continues offshore for at least 13 km, with high tin grades found within the palaeochannel but also dispersed across the sea floor as a sheet wash, a result of Quaternary sea level change reworking the placer deposits. This drowned portion of the coastal plain contains a continuation of rich tin leads as low gradient anastomosing channels, and has been delineated by marine seismic and drilling activity since the 1960s. Tin grades in the Tertiary and Quaternary alluvial profiles vary from 50 - 300 g/m3, with the highest concentrations in the coarser basal horizons. A previous offshore explorer estimated a resource of 194 Mm3 at 150 - 250 g/m3.Kenex Ltd created 3D models of the paleochannels and the mineralisation with the aim of better constraining the resource estimate and identifying additional depositional areas. The modelling was undertaken with the input of geophysical data, bathymetry and geochemical sampling of the seabed surface and from historic offshore drill holes. A prospectivity model covering Ringarooma Bay was produced to target tin-bearing gravels. Predictive maps were created to represent various features of the offshore mineral system, including assessing gradient changes in palaeochannels and their sinuosity. The model identifies areas with higher potential for alluvial tin mineralisation and will be used to focus the exploration programme over tenements currently held by Kenex Ltd."

Sep 1, 2014

By Klaus Rieker

The main train station of Leipzig in Germany is currently being upgraded from a head station to a partially thru station. In order to achieve this, significant ground improvements are necessary. Soil freezing for example is used to create the excavation box retaining walls. The freezing works will be carried out from two tunnels with an inner diameter of 2.4 m (~ 8ft). The tunnels were constructed by the pipe jacking method. The cutter head of the machine was equipped with discs and scrapers. Driving and excavation was carried out using a bentonite supported face. Due to the small arrival shafts, the machine had to be lifted out in components. The essential limitation of settlements during the drives was achieved even better than expected.

Jan 1, 2008

By Douglas Banks

Construction for the new 2.5 MGPD raw water intake project commenced December 2002. The project, initially designed as a 12' Ø concrete lined intake shaft,145' deep, with two offset 24" lake taps, 520' and 470' long was subsequently “value engineered” running the two lake taps through a single conduit. The offset for summer and winter pools was accomplished via a second shaft located at the lakes edge. Construction involved the use of blind drilling techniques for the shaft development and drill and blast techniques for the tunneling. All works were completed through extremely hard crystallized sandstone. The project came online August 12, 2004.

Jan 1, 2005

By Michelle Lostra, Red Blanchette, Jan Babendererde, Greg Colzani

The City of Portland’s Westside CSO Project is constructing a deep tunnel system to reduce combined sewer overflows (CSO) from entering the Willamette River. Several kilometers of microtunneled pipelines connect the existing system to the new tunnel. The alignments encountered a variety of ground conditions, including fill, manmade obstructions (wood, steel piles, debris), fine-grained to dense coarse-grained materials, cobbles and boulders, all below groundwater. A slurry MTBM convertible to varying diameters, equipped with mix shield capabilities, was selected to cope with the conditions. This paper will discuss access shaft construction,

Jan 1, 2005

By W. R. Reed

The National Institute for Occupational Safety and Health (NIOSH) uses light-scattering dust monitors (nephelometers) in its research to develop dust controls to reduce respirable silica dust overexposures in miners. Recently, the model 1500-pDR, an active nephelometer, was introduced by Thermo Scientific. Testing was completed to ensure compatibility with the metal/nonmetal mine dust personal sampling unit (M/NMDPSU). Results of testing demonstrated that gravimetric concentrations measured from the 1500-pDR are comparable to the gravimetric concentrations measured using the M/NMDPSU, without need for correction, under commonly observed dust loading conditions.

Jan 1, 2012

By S. K. Oraee

Managers always look for systems with minimum hazards. The hazards create problems for performance of projects. The largest and most important hazards of working underground mine can be related to health, safety and environmental, because if one of these sectors be in hazard, maybe lead to close mine. Failure mode and effects analysis (FMEA) is a widely used quality improvement tool to identify the potential failure modes for measuring reliability of a product or a process. FMEA is performed by developing a risk priority number (RPN), which is the product of severity, occurrence, and detection ratings. On the other hand, with regard to uncertainty in the decision-making, fuzzy theory will be able to model this uncertainty. Fuzzy FMEA provides a tool that can work in a better way with vague concepts and without sufficient information than conventional FMEA. This article by using Fuzzy FMEA and based on HSE criteria evaluate hazards of Parvade No. 1 Mine in Tabas Coal Mine. The results demonstrate the most hazardous parameter is rock burst in this mine.

Jan 1, 2011

By Allan Sylvester, Paul E. Gabryszak, Diane R. Hirsch, David P. Field

With construction of the first phase of the Automated People Mover (APM) Tunnels nearing completion, this paper will address how knowledge from recent Tunnel Boring Machine (TBM) and New Austrian Tunneling Method (NATM) tunnel construction at the airport was used to refine the methodology for the next phase of tunnels currently in design. The benefits include an enhanced understanding of the ground conditions; allowing optimization of excavation sequences and support requirements; a more effective instrumentation and monitoring program; and improved construction details and related contract provisions.

Jan 1, 2007

By Brian Khalighi, Massimo Franceschi, Giovanni Giacomin, Gianni Porta

Headrace Tunnels and parts of the Access Adit Tunnels of Kárahnjúkar Hydropower project, KAR-14, in Iceland will be excavated using three full-face Robbins Tunnel Boring Machines (TBM). TBM sizes range from 7.23 to 7.63 meters in diameter and the total headrace tunnel length is approximately 40 km. The crushed rock is transported on conveyor belts to disposal areas near each Adit. The estimated average excavation rate is approximately 25 meters per day per machine. Electricity will begin to flow in April 2007, and the project is scheduled for completion in 2009. This paper is divided into four sections. In the PROJECT OVERVIEW section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drives is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes in the TBM OPERATION section with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 2005

By James W. Bass

Introduction Atmospheric fluidized bed combustion (AFBC) is an improvement over coal-fired boiler design. It offers several advantages over conventional boilers. AFBC can meet sulfur and nitrogen oxide emission regulations without the need for add-on flue gas treatment equipment. The relatively low combustion temperature inhibits ash melting, thus reducing slagging and fouling that can in turn increase a boiler's fuel flexibility. AFBC process The fluidized bed boiler that operates at atmospheric pressure on the fire side (AFBC) is relatively simple and no different in purpose from those pulverized coal boilers used by utilities today. Fluidized bed boilers can generate steam at the pressure and temperature needed by modern steam turbines. Only the firing system is different. In fluidized bed combustion, the fuel can be almost any coal or waste fuel. It is burned in the presence of a bubbling bed of limestone. Air is forced through the bed at a velocity sufficient to support the weight of the bed particles. When the bed is fully fluidized, it bubbles like a boiling liquid. Although the burning coal makes up less than 1% of the fluidized bed, all the bed particles are heated quickly by the turbulence. The calcium in limestone reacts with sulfur dioxide produced in coal combustion to form calcium sulfate in a dry solid state. In this way, sulfur emissions regulations can be met without installing flue gas desulfurization equipment. Boiler tubes submerged in the bed absorb heat directly from the turbulent solids. The heat converts water in the tubes to steam or superheats the steam. Because of the intimate contact of the boiler tubes with the fluidized bed, heat transfer is highly efficient. Consequently, less boiler tubing surface is needed to generate the same amount of steam as in a comparable pulverized coal boiler. The optimum temperature for sulfur capture is relatively low, about 815°C (1500°F) as opposed to 1370°C (2500°F) for pulverized coal boilers. This results in the formation of lower levels of NON. Because operating temperatures are below those that fuse coal ash, a single design can burn a variety of coals without slagging or fouling problems. TVA's AFBC development program Tennessee Valley Authority's (TVA) involvement in AFBC development began in 1974 and has addressed the technical uncertainties through a comprehensive program of design, experimental, and analytical studies. In 1979, TVA and the Electric Power Research Institute (EPRI) developed plans for a 20-MW AFBC pilot plant, a 10-fold scale-up over the next largest test facility. Pilot plant design features TVA constructed the pilot plant at the Shawnee Steam Plant near

Jan 4, 1986

By V. L. Franzen, Z. J. Hladysz, C. A. Kliche

The Wharf Resources mine, located in the Bald Mountain Mining District approximately 6.4 km (4miles) west of Lead, South Dakota, has operated a surface gold and silver mine and heap leaching processing facility since 1983. Wharf Resources intends to mine and process gold and silver ore from the Wharf Expansion area which is located on the eastern flank of the currently permitted Foley Ridge Mine. The Trojan Pit for the Wharf Expansion area was initially designed with an overall highwall slope angle of 45o. During mine permit presubmission meetings with personnel from the SD Department of Environment and Natural Resources (SD DENR), the question arose as to whether a detailed slope stability analysis of the proposed Trojan Pit highwalls was completed to justify the 45o slope. Wharf’s response was that the highwall design was based, in part, upon studies completed in1987 on the Annie Creek and Foley Ridge Mines; and, in part, upon subsequent slope stability analyses conducted by Wharf mine personnel through 1996. It was suggested by the SD DENR that the stability study be updated to reflect structural geological conditions in the Wharf Expansion area.

Jan 1, 2000

By Sohta Takatsu, Hachiroh Mizubata, Shigeki Kudoh, Kazuya Takekuni, Yoshinori Yamada

A special type of shotcrete is used to improve the performance of open-type TBM in difficult situations. The Hakamagoshi and Johana tunnels are expressway evacuation tunnels of 3.2 km and 5.1 km in length, respectively (total 9.1 km) that were excavated by one open-type TBM. The geological conditions at the sites were estimated to be good before excavation. However, 95% of the rock turned out to be two ranking orders worse than the estimated classes. Therefore, we used a special shotcrete for bad rock conditions, and succeeded in excavating the tunnel at an average rate of 270 m/month.

Jan 1, 2001

By J. M. Wempen

Booster fans, large underground fans, can increase the volumetric efficiency of ventilation systems by helping to balance the pressure and quantity distribution throughout a mine, reducing leakage and reducing the total power requirement. However, in ventilation systems that use booster fans there is a potential for system recirculation, the leakage of return air to intake air, and also for localized recirculation near the fan through the bulkhead and airlock doors. Air that is recirculated locally decreases the system efficiency because the quantity of air flow through the fan increases without increasing the airflow throughout the system. To understand the detailed flow characteristics of a ventilation system with a booster fan, two-dimensional computational fluid dynamics (CFD) models were developed using the software Ansys-FLUENT. Though two-dimensional models do not represent the full complexity of the flow dynamics, they do provide a good representation of the flow characteristics and they allow for a qualitative analysis of how the flow dynamics are affected by the system characteristics. The CFD models were used to evaluate how the number of booster fans, the booster fan placement, the location and geometry of the fan installation and the construction of the airlock system affect the flow characteristics and the localized efficiency of the ventilation system.

Feb 27, 2013