Search Documents

By Eugene F. Casey, William H. Hansmire, J. Ghaboussi, Randall L. Lentell, Harvey W. Parker

INTRODUCTION Construction of a major intercepting sewer in Brooklyn, New York involved tunneling in soil over several subway lines. In two instances the clearance between the subway and sewer was sufficiently close that concern was raised about the influence of the new construction. Prior to each critical crossing, analytical studies were performed which characterized the tunneling influence. It was demonstrated that with adjustments in construction procedures the crossings could be made without affecting the integrity of the subway linings. A comprehensive program of instrumentation and full-time monitoring was undertaken to ensure that any unforeseen adverse developments during crossing would be recognized. The successful crossings were subsequently made with minimal influence. Reported herein are the special construction conditions for the two crossings, the analytical simulation of behavior, and the results of monitoring on the subway linings. SEWER TUNNEL CONSTRUCTION AND EXISTING SUBWAYS The Red Hook Intercepting Sewer is a 2600 m (8600 ft) long tunnel which is part of a major water pollution control project in New York City. For clarity of nomenclature, the sewer is termed a 'tunnel' while the rapid transit structures are termed 'subways'. For routine construction, the tunnel was mined by hand with a 3.2 m (10 ft-5 in.)

Jan 1, 1981

A significant technological development is discussed for the processing of certain problem power plant flyashes which contain a high water soluble mineral content and which are known to yield inferior flyash based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash based structures. Favorable changes are evident in (1) sodium silicate consumption, where often approximately one-half of the amount used for making brick from normal flyash is required; (2) processing costs; and (3) strength and appearance of the resulting freshly formed green and fired structural products. In some high cost instances-(above the cost of 30 dollars or less per thousand brick estimated for normal flyashes) hydrochloric acid additions can replace or reduce other costly additives required with problem flyashes to result in a savings of as much as nine dollars per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble, sulfur as a result of the eventual application of certain experimental air pollution control processes.

Jan 1, 1968

By W. A. Haley

As far back as 1939 state laws have required reclamation of mined lands. Reclamation has been the topic of many discussions and presentations, especially since the late 1960's. In the past ten years many states have added legislation concerning the reclamation of coal-mined lands. In the near future, it seems certain that some federal regulations will be passed that will set minimum guidelines for the states to regulate. Besides the requirement of returning the land to the approximate original contour, future regulations will more than likely demand replacing topsoil from one to five feet thick. As regulations become more stringent, costs will rise accordingly. Since no one has developed a machine that can do all reclamation work by itself, it is necessary to review in detail the tools available and to select the most economical means.

Jan 1, 1976

By Herschel H. Potter

Back injuries arising from such activities as lifting and handling objects have been and continue to be constant and undiminishing hazards of the occupational environment. Back pain in one form or another is experienced by almost a1 1 individuals. During the past 30 years, a great deal of accident prevention education has been directed toward the reduction of back injuries. However, it has not produced any great change in the incidence of the injury. The human spine remains the most vulnerable area of the muscul o-skeleta1 system. Back injuries account for about 400,000, or 18 percent, of all disabling work related injuries each year according to the National Safety Council estimates. These serious back injuries are estimated to have cost more than 1.9 billion dollars in 1976 in medical and lost time pay. 1

Jan 1, 1981

By I. Longson

As a longwall coalface advances a caved goaf or waste region is left behind. Air flow takes place through this permeable goaf due to the pressure differentials existing across it and en route this leakage air picks up both heat and moisture. A marked deterioration in climatic conditions occurs in the face area at all points downstream of where this leakage air rejoins the main air-stream. This goaf heat source can make a very significant contribution, typically 30-40% to the rate of total heat pickup on an advancing UK longwall coalface with a VST of 40°C and hence on the climatic conditions that prevail at the return end and in the return gate of the face. The magnitude of the rate of heat collection from the goaf depends on a number of factors but it has been established that it is particularly influenced by the prevailing virgin rock temperature and the total flow rate of the leakage air. This paper proposes a model for the goaf based on a packed bed analogy and other assumptions required in order to evaluate the rate of heat pickup are identified. The outlet condition of the leakage air predicted by the model have been shown to correlate with underground measurements taken for a range of different production patterns with the face cutter at various locations on the face. The sensitivity of these predictions to variations in the input data has been tested and is commented on. At this stage of the development the capabilities and predictive limitations of the model are discussed. Further areas of investigation are suggested in order to improve the predictive ability and to extend the versatility of the model.

Jan 1, 1989

I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent com¬parative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging.

Jan 1, 1987

By J. A. Finch, B. J. Huls

Accurate level detection is required to make full use of level in optimizing control strategies for flotation columns. Techniques based on pressure and electrical conductivity are compared. Pressure and conductivity profiles give good agreement on level. Level calculated from single and multiple pressure values became more accurate using, in order, one, two and three sensor locations. The level estimate remained in error, however, because, unlike the collection zone, froth zone bulk density varies with height. A conductivity probe continually updating the conductance profile is a practical method of obtaining an accurate level.

Jan 1, 1990

By M. D. Bishop

Early solvent extraction circuits in the uranium industry utilized bona fide kerosenes as diluents for extractant chemicals. These kerosenes were used successfully in the uranium industry; however, at least one plant was destroyed by fire resulting from the use of a low flash point kerosene. Although the term "kerosene" is used throughout the solvent extraction industry, the authors have been unable to find any use of kerosene in copper solvent extraction circuits. A term that is occasionally used with reference to diluents is "metallurgical kerosene." Such a term is unrecognizable in the petroleum industry. Kerosene [or kerosine] is a flammable hydrocarbon mixture that is less volatile than gasoline. It is produced for combustion purposes and may have variable compositions of organic compounds including alkanes, alkenes, alkines, and aromatics. Diluents are constant composition hydrocarbon mixtures developed specifically for use in solvent extraction processes. These products usually have much lower vapor pressures and higher flash points than kerosene. In solvent extraction systems, they typically comprise 70 to 95 v/o percent of the circuit organic. The primary purpose of the diluent is to adjust the extractant concentration to the working range of the operation. The diluent and extractant must be completely soluble or miscible with each other. Secondary diluent effects are to promote transfer kinetics, optimize phase disengagement, and minimize both organic in aqueous and aqueous in organic entrainment.

Jan 1, 1996

By Thon T. Gin

The lithologic, mineralogic, and magnetic beneficiation characteristics of the iron formation at U. S. Steel's Atlantic City Ore Mine, Fremont County, Wyoming, have been determined. The iron formation averages about 30 percent Fe content, and varies from 125 feet to about 500 feet in thickness. It is composed of interbedded magnetite-rich quartzites, magnetite-quartz-amphibole schists, and amphibole-chlorite schists. Quartz, actinolite-tremolite, chlorite, and magnetite are the essential mineral constituents. These rocks are differentiated into four major ore types on the basis of their relative quartz and amphibole content. The iron content of the magnetic concentrate decreases and the silica content increases with decreasing grain size and increasing amphibole content in each ore type at the same fineness of grind. Criteria were developed to enable the mine operator to recognize the ore types and to blend them to produce a more uniform concentrator feed. This results in less variation in product quality and requires fewer changes in operating conditions-in the concentrator.

Jan 1, 1965

By K. R. Griffin, K. D. Luxbacher, E. C. Jong

The schlieren technique describes an optical analysis method designed to enhance light distortions caused by air movement. The ability to visualize air flow has significant implications for analyzing underground mine ventilation systems, including the enhancement of surveys and models. Currently, traditional schlieren methods are impractical underground. Background-oriented schlieren (BOS) provides a solution to this problem. BOS requires two primary components, a professional quality digital camera and a schlieren background. A schlieren background is composed of a varying contrast repetitive pattern, such as black and white stripes. This background allows the camera’s sensor to capture minor light diffractions, such as those caused by air flow. Although BOS shows great potential for ventilation analysis, sensitivity is an issue. This paper seeks to validate the BOS technique for imaging flow through a regulator by comparing BOS images with traditional schlieren images. This paper also outlines initial experimental efforts used for the validation.

Jan 1, 2011

By Susanne Pignolet

Ore microscopy has been applied to the complex lead-zinc-copper-cobalt-nickel ores from the Madison Mire in the Fredericktown subdistrict of the Southeast Missouri Lead District to predict potential beneficiation problems. It has been found that in some portions of the ore deposits, textures are present which may result in metal losses. In ores from the Bonneterre Transition Zone the intimate association of siegenite with chalcopyrite may result in cobalt and nickel losses to the copper concentrate. In ores from higher stratigraphic horizons, this association is relatively uncommon, and siegenite is commonly associated with bravoite. This latter association will increase the recovery of the cobalt and nickel in bravoite, even though some of the fine-grained bravoite will not be recoverable. Other textures which may result in potential beneficiation problems include coatings of covellite on chalcopyrite and inclusions of sphalerite in galena.

Jan 1, 1983

By J. van Oldenborgh

The world market for bunkers represents some 140 MT (1980) of marine fuel oil and distillates. This is equivalent to 23CMT of coal, a potential market for steam coal larger than the total seaborne trade of steam and metallurgical coal today, and an obvious area which could contribute savings in world oil consumption. Oil bunkers are lifted fairly evenly throughout the world, the main supplying regions being Western Europe, the Middle East, North and Central America and Japan (Figure 1). Not surprisingly, the main customers are the tankers representing about 50 percent of the world market - (95 percent of the Middle East Market) - dry bulkers represent some 30 percent and general cargo ships the rest.

Jan 1, 1982

By Dan Nilsson

Rock from underground mining has a size-distribution, that varies from mine to mine, depends on rock conditions and mining method and on how much explosives etc, that is used. Because at the high costs, associated with full-scale studies of the size-distribution of blasted rock in a mine, detailed information is seldom published about such size-distributions. However, some facts can be noticed. Rock from tunnelling and other types of development work has a fine fragmentation. Cut-and- fill mining is a method that normally results in blasted rock with an advantageous size distribution. Block caving on the other hand often results in large amounts of boulders, since blasting of the rock is normally not used.

Jan 1, 1985

By Hans Svensson

INTRODUCTION The Alimak method of raising (Fig. 1) was intro¬duced in 1957. Because of its flexibility, economy, and speed, it soon became the most used system of raising in the world. With the same unit, raises of various areas, inclinations, and lengths can be driven. Air-motor¬-driven raise climbers normally are used in mines with short raises (Fig. 2). For longer raises electric or diesel-¬hydraulic drives are used. The Alimak raise climber is designed entirely in ac¬cordance with the instructions of the Swedish Board of Industrial Safety (Arbetarskyddsstyrelsen). There are good margins of safety concerning the breaking strength of the material and the raise climber comprises safety devices and features that practically eliminate the risks of accidents. The drive gear of air-driven climbers is equipped with an air-operated brake which is automatically activated when air for the motors is shut off. There is a safety device which activates automatically at overspeed and a speed-regulated brake for descent by gravity, by which the raise climber can be taken down to the bottom of the raise in case of cutoff of the air supply. The raise climber climbs along a pin rack welded to a guide rail which also comprises pipes for air and water. The guide. rail can be extended by using 1- or 2-m (3.2¬or 6.4-ft) sections as the driving progresses. Each guide rail section is bolted to the rock wall by special expan¬sion bolts of Alimak design. Men ride up to the face in the cage, traveling com¬fortably and easily while material is transported on the platform. There is no dangerous climbing up ladders. The men are well protected during ascent and arrive in good condition at the face. The greatest advantages of raise climber systems are flexibility and versatility. The equipment provides a comfortable working position in vertical as well as in¬clined raises of any area and length. The direction may

Jan 1, 1982

By John B. Wright

This paper describes laboratory techniques and subsequent results of Bureau of Mines research to produce chlorination-grade feedstock from an abundant, low-grade, domestic, rock ilmenite ore. The research is part of the Bureau-effort to devise technology that may help decrease U.S. dependence on imported raw materials. A rock ilmenite containing about 46 wt pct Ti02 was smelted in an electric arc furnace with coke, woodchips, and Na2C03 to separate most of the iron as pig iron and to form a low-iron, titanium-enriched slag. The slag was ground, pelletized, oxidized, and then sulfated with mixtures of SO2 and air in a continuous 4.5- to 9.1- kg/h apparatus at 1023 to 1223 K. The sulfated slag, containing 60 to 65 pct TiO2, was reground and leached in water at ambient temperature to decrease the combined levels of the troublesome Ca, Mg, and Mn impurities from 7.0 to 1.7 wt pct. At levels of more than 3 wt pct, these impurities contribute to operating and disposal problems, The final product was upgraded to about 84 wt pct TiO2. This material potentially is suitable for chlorination in a fluidized-bed reactor. The most favorable results were achieved with leached slag sulfated at a feedrate of 4.5 kg/h and at temperatures of 1073 to 1123 K.

Jan 1, 1984

By Chris Roos

The mining industry has made strides in planning for operations to be safe for the workforce and public, to protect the natural environment, and to maximize value for shareholders. However, many of the techniques used to accomplish these goals are based on estimated models of mineral content, production efficiency, and economic performance. The industry has begun to recognize the need for understanding the uncertainty in these models, how it affects their decisions, and what the potential impacts are for each project. The challenge has become how technical professionals can effectively communicate the impact of this uncertainty and its importance to both technical and non-technical audiences. This paper presents mining engineers (and other technical professionals) with traditional and modern principles of data visualization and technical communication that can assist with communicating the effects of uncertainty in the mine planning process.

Jun 25, 2023

By M. Gunter, M. Buzon, B. McNamee

"A Google search on talc asbestos will yield over 500,000 hits – the reason being the growing number of civil lawsuits in this area. Historically the litigation was centered on amphibole-containing industrial talc. There was no debate these talcs contained amphiboles, but the issue was the definition of asbestos. Ultramafic hosted talcs, however, are formed in such a way as to not favor the formation of amphiboles in the talc; they can occur in the surrounding black-wall, also the serpentinite host rock is in direct contact with the talc. Thus allegations can be made non-asbestiform amphiboles or non-regulated serpentine group minerals can occur in the final products. INTRODUCTION Gunter (1994) wrote the following in regard to the question “What is asbestos? “The question yields different answers depending upon the audience. To a mineralogist, asbestos is a mineral form. To an engineer, it is an industrial material with several useful properties. To a medical doctor, it is an agent that might cause certain diseases. The third answer invokes several more issues: to a lawyer, a possible lawsuit; to a news reporter, a story; to an asbestos abatement worker, a job; and to a public school administrator or a parent, a nightmare.” The main function of that article was to try and provide background information to be taught at the college level to help students understand some of the issues associated with the use of asbestos in our modern society, and especially its use as a fireproofing agent in schools and public buildings. At that point in time one of the main issues was asbestos abatement as the mining and use of asbestos was waning as its health risks became more clearly known in the occupational setting. Now over 20 years later the current issue we are dealing with herein is “asbestos” occurring naturally in talc. This is a well know concern for those in the talc industry and they have been working on methods to ascertain if their products contained “asbestos” since last century. As such our articles will focus more on issues emerging from recent litigation, and the confusion that occurs, especially in the “asbestos” nomenclature as the mineralogist, engineers, doctors, and lawyers previously mentioned try to communicate. And lastly we need to remain cognizant of the fact that people are still dying of mesothelioma in the US. As a last resort to recoup expenses as they are dying they often respond to the TV advertisements we’ve all no doubt seen."

Jan 1, 2016

By J. W. Leonard

Since the interpolation of exploratory data 1 can be no better than sampling procedures, a series of field experiments were conducted in an effort to determine whether hand-cut channel or core washability determinations best represent continuous miner produced run of mine coal. By obtaining a core drilled to within a few feet of channels taken from an underground face and then overmining both locations; core, channels and run-of-mine coal allocations were obtained from a common sample and all allocations were subjected to identical washability determinations. In order to compare results, basic rules2,3 previously anticipated and later published by the writer were employed. The first rule states that "For any full seam washability determination, the sulfur versus ash function for increasing cumulative specific gravity float coal fractions is linear". The second rule states that "For any full seam washability determination, the recovery versus ash function for increasing cumulative specific gravity float coal fractions is logarithmic".

Jan 1, 1988

By J. Richard Lucas

Today, the future of the coal industry is extremely bright because coal can be produced at a cost which makes it competitive with other energy sources. However, the industry has been forewarned that further cost reductions must be made if it expects to remain a serious contender in the growing energy market. Surface as well as underground operations must be improved. The very same elements which affected production a. few years ago still exist today and will continue to be present in the future. Improvement's in production mining equipment, mining methods, and auxiliary equipment have resulted in reduced costs over the past few years. Efforts must be continued toward further reducing costs in areas which have been improved previously, and new areas should be investigated for possible improvements. Therefore, new techniques must be developed which will enable the industry to augment its current efforts in reducing the cost of mining. The logical place to begin evaluating the factors affecting production and cost is in the immediate face area where a substantial part of the total cost of mining is incurred. The coal industry stands to gain much through the development of new techniques for analyzing the numerous variables affecting production and by establishing methods for eliminating or minimizing the adverse effect of those variables which can be controlled. Intuition and trial-and-error methods have been the standard means used to resolve many of the factors which influence production. As a result, many elements are overlooked or ignored because their effect on production is not pronounced and cannot be readily resolved. The need for a method of analyzing such factors was recognized by the Office of Coal Research. Therefore, in April 1962, under OCR sponsorship, a. research project was initiated at Virginia Polytechnic Institute (VPI). The objective of the project was to identify the factors which influence mining costs in the immediate production area, and to develop methods and techniques which will enable the coal operator to minimize production costs. The objective of the research at VPI has been successful, and techniques have been developed for establishing quantitative facts concerning the interrelationships of production activities.

Jan 1, 1965

Underground mining alters ground condition, producing a disturbance in the ground water regime. The level of disturbance is dependent on the local hydrology, geology, and type of mining. Serious damage is sometimes caused by ground water- when mine roofs collapse, causing subsidence. Subsidence is either unplanned, where pillars are inadequate to provide support; or planned, where total extraction occurs over a large area. The primary objective of this study is to investigate the effects of mine subsidence on the ground water hydrology in the Warrior Coal Basin. Underground openings resulting from coal mining activities have been the most significant cause of subsidence problems in the Warrior Coal Basin, the main source of coal in Alabama. This problem will be even more serious in the future because 19 of Alabama's 24 billion tons of coal reserves are classified as an underground source (Tolson, 1982).

Jan 1, 1987