Search Documents

By Thomas E. Shufflebarger

Definition of glass sand prospects may be modified by constraints which range from demography to critically important product-control. Characteristics of usable raw materials, physical and chemical, are discussed; an ideal raw material is defined. Following field investigations and preliminary sampling, evaluation of selected prospects includes use of modern drilling techniques, viz.: core, percussion (air-hammer), auger, jet, rotary jet, split-spoon and other. Nearly complete core (sample) return is mandatory. Land-use regulations, availability of water and transportation continue to direct exploration in a major sense. But fitting a prospect to burdensome politics nay be considered a decidedly negative factor.

Jan 1, 1983

By E. A. Córdova

Current methods for scratching a piece of rock to obtain or check the characteristics of its component material can sometimes be expensive and time consuming. Scratching a rock core requires an object with a point that it is capable of sliding along the surface of the rock while recording the response from the rock due to the sliding. With the idea of providing a cost efficient solution for a scratch device, a new generation turntable arm, composed of a cartridge with a diamond stylus and a USB output connection to the computer, was used to record the vibrations from the sliding of the stylus along a rock core surface. The output sound from the stylus was captured with the computer as an audio input signal. The raw sound data was recorded in a standard waveform audio format (wav) file, and post-processed using sound spectrum analyzer software (Spectra-Lab) to capture numerical data such as frequency, amplitude, and noise from the file. The results for frequency, amplitude, and noise were compared and plotted against the scanned surface of the rock core in the search for correlations that might represent specific characteristics of the surface being scratched.

Jan 1, 2010

By Peter N. Calder

The selection of a slope angle for an open pit in rock has often been made without the benefit of a comprehensive engineering study. This is largely due to the fact that the hardware and procedures necessary for such a study have not been available. Recently this situation has been reversed. The application of borehole television and terrestrial photogrammetric devices has made possible the accurate determination of rock joint structure, on which stability calculations can be based. Another important aspect is the evolution of practical methods of conducting in-situ rock joint strength tests.

Jan 1, 1971

By P. A. S. Manning

Eastern Jamaica consists predominantly of non-carbonate rocks reaching elevations of over 2200 m. The area is drained by a well established river network which supplies close to 30% of the sand and gravel used by the building and construction sector. Present high extraction rates and slow rates of replenishment will result in early exhaustion of this source of aggregate. A number of volcanic and carbonate rocks are being examined as a possible source of high quality aggregate which meet the requirements for all types of construction. Preliminary evaluations show a dacitic deposit to be the most suitable source for aggregate use.

Jan 1, 1998

By Robert M. Becker

The evaluation of in situ rock stresses from measurements of the change in diameter of a borehole that is stress-relieved by overcoring has become a common practice. Generally the stress evaluation has been based on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium has been adapted to evaluation of in situ stress. The necessary elastic parameters for this evaluation may conveniently be obtained from static tests on the overcore in conjunction with a consistent orthotropic thick-wall cylinder solution. The method and equations for the laboratory and field evaluations are summarized and illustrated.

Jan 1, 1968

By Gerry Norton

The purpose of this paper is to make the most complete assessment of coal cleaning methods, both process and equipment related to modern-day production and environmental requirements. In order to achieve this primary objective, a number of interdependent aspects of coal cleaning technology require evaluation and analysis. 1.0 CLASSIFICATION OF SEPARATION PROCESSES Processes and cleaning equipment can be categorized according to the important parameters of 1) mechanics of separation, 2) size range application, 3) range or variance in accuracy of separation related to 2) above, and 4) feed-size ratio affecting 3) above.

Jan 1, 1977

By G. Castillo, J. Mortensen

"INTRODUCTION Molybdenite is typically produced as a co-product in the copper ore flotation process. At the Rio Tinto Kennecott Concentrator (RTKC) in Copperton, Utah, the molybdenite is initially floated with copper sulfides and other value minerals producing a Cu-Mo concentrate. This is then separated in the molybdenum plant by depressing copper sulfides and pyrite and floating only molybdenite. The molybdenum plant in RTKC comprises the rougher circuit and several stages of cleaning to achieve a certain grade requirement of Mo. The rougher circuit is where the first stage of separation occurs. Cu sulfides and pyrite are depressed in the rougher circuit by adding NaSH under nitrogen and in the cleaner circuit by adding NaSH under air. The depression of Cu sulfides (and pyrite) by NaSH is related to the redox activity1. It is important therefore to maintain a reducing potential in the circuit in order to achieve effective Cu-Mo separation. If the rougher circuit is under air, like RTKC’s molybdenum cleaner circuits, it is harder to maintain the target redox potential because NaSH oxidizes rapidly in the presence of air thereby increasing NaSH consumption significantly. CU-MO SEPARATION AND ROLE OF PULP POTENTIAL The collector adsorption on copper sulfide minerals is through an electrochemical mechanism2. The collector changes the surface chemistry of the Cu mineral allowing it to float. Molybdenite, or MoS2, on the other hand, floats readily in the presence of a frother as it is naturally hydrophobic. Usually, hydrocarbon oil extenders such as diesel or burner oil are added to enhance Mo recovery. In order to effectively separate Cu from Mo, the collector complex on the copper surface needs to be destabilized or desorbed using a reducing agent such as NaSH or Nokes. As long as the circuit is under highly reducing conditions, the collector remains detached from the sulfide mineral surface allowing Cu sulfide depression. Therefore, it is important to measure the oxidation-reduction potential (ORP) continually and maintain the reducing condition with addition of NaSH. For a given collector each mineral will have a characteristic potential or electrochemical window for flotation to occur3, therefore, it is necessary to reduce the potential outside of this window in order to effectively separate Cu and Fe sulfides from MoS2 minerals2. In RTKC plant, the target reducing condition is between -450 to -550 mV to effectively destabilize the collector and depress Cu and Fe minerals. Typically the dosage of NaSH used in the molybdenum plant could range from 6 to 30 gallons/min (gpm). The high dosage of NaSH could pose risk of H2S exposure. RTKC wanted to evaluate alternatives to NaSH in order to reduce its consumption and minimize risk of H2S gas generation."

Jan 1, 2016

By Lawrence P. Kennedy

The Lynne deposit is a volcanic-to volcaniclastic-hosted, Zn-Pb-Cu-Ag orebody located in the early Proterozoic magmatic terrain of northern Wisconsin. As of February 1991, core drilling has partially delineated a multi-million ton, near-surface, disseminated to massive sulfide deposit. The deposit is hosted by a gently dipping sequence of fragmental rhyolites, felsic tuffs, less abundant dacite to andesite flows, and fine-grained volcanic sediments. The deposit is broadly conformable With the host rock stratigraphy, but the ore zones thicken and coalesce in the central part of the deposit.

Jan 1, 1991

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016

By E. A. Twichell

An entirely new concept in the effective utilization of magnetic, energy has resulted in a major break-through in the design of magnetic separation equipment. One of the first applications of this concept has resulted in the development of a Permanent Magnetic Wet Drum Separator with strength .and operating characteristics equal to Electro Wet Drum Separators. Prior to this development when strength and adjustability were required, electro wet drums were specified even with all their drawbacks. The electros, by nature, are subject to coil failure or burnout, over-heating and loss of strength, high power consumption and generally high maintenance. Now the high strength and the adjustability, formerly the exclusive property of electros, has been engineered into permanent wet drum separators. These units combine maximum field strength in the separation zone with strength adjustment to suit changing conditions. Adjustment can be effected while the drum is in operation without stopping either the feed or the drum.

Jan 1, 1967

By Andrew T. Zador

The growing demand for energy combined with the need to protect and preserve the environment have become prime considerations in the design of efficient coal handling ports and their associated stockpiles. The transportation system is analogous to a connected chain which originates at the mines and terminates at steel mills or power plants, in which the port and the stockpile reserves are a vital link. Railroad transportation costs can be minimized by rapid discharge of the cars which, in turn, requires that an adequate stockpile system be available. Ocean transport costs can be minimized by having an efficient high capacity ship loading system and sufficient quantities of coal on hand -all of which also requires an efficient stockpile system to meet shipping demands. The connector between the two modes of transportation, therefore, is the port stockyard. It is here at the interface that optimization of land utilization and materials handling equipment results in a total transportation chain that can operate as a smooth efficient system. Multiple origins of coal require the simultaneous handling of large quantities of coal of many grades. Railroad transportation logistics often limit and define the incoming arrival patterns and limited rolling stock often require priority treatment for railroad operations. The physical limitations of prime ocean frontage require that coal stockpiles be built close to residential or industrial areas which entail strict environmental controls. Large capacity, enclosed coal stockpiles for ocean shipping have not yet been considered feasible but may be forthcoming in the near future. Several have been analyzed.

Jan 1, 1978

By William J. Lang

In just over a generation, the United States bentonite industry has grown from almost a rake and shovel operation into one with a multimillion ton annual production rate and exports to all corners of the globe. Bentonite production, pressed to keep pace with the soaring demand, has increased more than 10 fold in the last 30 years. The worldwide demand for bentonite is expected to double during the next eight to ten years. It remains to be seen whether U.S. producers will be able to maintain the dominant position in the world market. It should be noted that accurate statistical information regarding production or market information is difficult or impossible to obtain abroad and also within the United States. Published information obtained in response to questionnaires of the Bureau of Mines tends to be on the conservative side. FOUNDRY It has only been in the last thirty or forty years that bentonite has become an indispensible part of the age old metal casting industry. The relationship has proven most beneficial to both industries and promises to be long lasting. The foundry market for bentonite was the least of the three major markets twenty years ago but now leads all others and consumes 1/3 or more of the

Jan 1, 1971

By A. G. Belova

With the federal climate change legislation in progress, there is a need for demonstration-stage technologies aimed at providing clean energy from coal. Our research aims to experimentally illustrate the feasibility of capturing CO2 on a novel sorbent system from a gaseous stream. The gas is then released resulting in a regenerated sorbent and a pressurized stream of pure CO2 to be used for storage. The proposed sorbent is a ceramic honey-comb structured monolith coated with CaO supported on a high-surface area alumina. CaO is a natural acceptor of CO2 and our design ensures the physical stability and chemical reactivity of CaO over a large number of CO2 capture/release cycles. Furthermore, the use of the monolith ensures a uniform flow through the reactor, minimizes pressure drop across the reactor, and maximizes the surface reactive area. In this paper, we will present the results from a flow-through laboratory-scale reactor that establishes the efficiency of the proposed system to capture CO2. Future applications of the reactor include integration within the new-generation coal gasification power plants, such as IGGC, as means of providing decarbonized electricity.

Jan 1, 2010

By M. Guzman, S. B. Thais, M. F. Obispo, M. R. Arribasplata

The impact generated by old abandoned mines in Peru have produced mining environmental liabilities, which can generate an impact on the environment. In the search for long-term sustainable solutions, Phytoremediation is presented as an interesting alternative, since it allows the use of Peruvian native plant species for the accumulation of heavy metals. In this paper, we present the results of native high Andean species: Stipa Ichu and Cortaderia Nitida. The final metal concentration in the aerial parts and in the roots of each plant show that Stipa Ichu is more efficient to recover Fe, reaching almost 278 times its initial value. In the same way, this plant is efficient to remove Zn, Cu and Cd, reaching maximum values of 64, 39 and 12 times its initial concentration respectively. Cortaderia Nitida turned out to be more efficient to recover Fe, Zn, Cu and Cr, with highest recovery of 250, 117, 39 and 13 times its initial value respectively. Finally, based on translocation factor, Stipa Ichu has better capacities of hyperaccumulation of Fe, Cu, Zn, Pb and Cr. Cortaderia Nitida only shows hyperaccumulation of Cr.

Mar 2, 2022

By Roberto Pimentel de Souza

CURD started producing pellets in 1969, with one two-million ton straight grate plant. In the beginning of April '73, the second unit came on stream with an additional capacity of 3 million TPY of pellets. In January '77, the third unit started, bringing the annual capacity to 8 million TPY. For the present year 3 more units, 3 million each, are expected to begin production. CVRD's experience is given about the use of different binders and additives. Over the years several kinds of pellets have been produced to satisfy the market requirements. General quality information is given regarding each.

Jan 1, 1978

By Leland L. Mink

Open-pit mining is sometimes conducted in areas where the artesian pressures contained in aquifers underlying the pit's floor are great enough to cause floor heave. In order to reduce this pressure several methods are commonly used. One of these methods is a pressure relief well or depressurization wick. The wick consists of a borehole which is filled with gravel and cased at the surface. The wick is allowed to flow freely, thus reducing pressure near its location. The spacing and depth of these wicks can be determined by a simple analytical and graphical technique which considers the weight of material overlying the aquifer and the artesian force within the aquifer. An example of the technique using data from a Colombian coal mine is presented.

Jan 1, 1986

By K J. Kidd

There is general understanding of hoisting systems throughout the mining industry. However, the relative importance of the various parameters influencing hoist selection and utilization is not completely understood. In order to determine if these parameters can be identified and prioritized, data covering 613 hoist installations were compiled. The 613 installations represent hoisting systems in 30 countries on six continents. This study compares data to historical trends, correlates design parameters in an attempt to identify underlying selection criteria, and comments on the apparent trends in recent developments in hoist design.

Jan 1, 1998

By S. D. Thompson, L. Adler

This study reviews and analyzes the empirical methods available for designing the capacities of coal mine gathering belts. The analyses lead to recommendations concerning the application and implementation of each empirical method. Operations research techniques, mainly simulation models, are also briefly mentioned, and a few recommendations are made concerning their selection and application. The objective of the study is to provide a reliable basis for the practicing engineer to properly select, apply, and implement a capacity design method.

Jan 1, 1988

By John E. Tilton

Mining is one of the oldest human activities. It goes back at least to the Bronze Age and possibly even the Stone Age. The Romans mined copper in Spain and tin in England some two thousand years ago. The writings of Agricola in the 16th century show that mining was important in the Middle Ages. Today we mine more mineral commodities in greater tonnages than ever before. This long and fascinating history closely tied with the economic development of the human race is one of the charms of the mining industry. It also, unfortunately, gives rise to some widespread misconceptions.

Jan 1, 1997

Ventilation 'is currently used in mines to sustain human life, prevent explosions, and provide a more healthful work place. Future automated-mining systems could use ventilation techniques quite. different from today's practices. The Bureau of Mines is anticipating various methodologies for ventilating the automated mining systems which are now beginning to emerge in the mining industry. This paper examines the special ventilation requirements for automated mining systems. Topics include requirements for automated systems, current studies with blowup ventilation tubing, and ventilation of two types of highwall -ripper type mining machines.

Jan 1, 1990