Search Documents

By W. Lin

When a large area of open gob collapses suddenly, a windblast is produced that can cause considerable damage throughout the infrastructure of a mine. In a few cases, the windblast has been accompanied by ignitions of methane and/or coal dust. This paper describes the conduct and results of laboratory tests involving the compression of mixtures of air, methane and coal dust under a falling weight and while allowing controlled escape of the mixture. The transient responses on pressure and temperature sensors were recorded. In addition to an analysis of those records, the paper highlights those conditions in which ignitions occurred.

Jan 1, 1997

By J. H. Meza Viveros

This paper describes some actual parameters and technologies used at Mexicana de Cobre Smelter, and the principal design parameters and new technologies which wiil be used with the smelter expansion project, in order to increase the production capacity of anode copper from 180 000 mtpy to 300 000 mtpy. Likewise its describe some parallel projects under construction also in the smelter plant.

Jan 1, 1997

By M. C. Baumann

The Getchell Mine is located in Humboldt County, Nevada, approximately 70 km northeast of Winnemucca. Slope management has been a critical factor in the feasibility of mining operations since they began in the early 1930's. Although underground entries began in 1937, underground production was limited because hanging walls consisting of clay gouge and crushed rock tended to collapse into the workings. Controlling these collapses required extensive timbering. Due to these poor ground conditions, surface open-pit mining was the primary mode of production from 1938 to 1967 with only minor contributions from underground operations. Mining was suspended in 1967 due to economic pressures. From 1960 to 1967, the previous operator mined the property in three open pits. Initially, these pits were constructed with footwall benches, but these failed. These failures were aggravated by construction of 60° slopes in footwalls with shale partings dipping into the pit at 43° to 60°, resulting in large planar failures and wedge failures. In response, the previous operator adopted a slope parallel to the bedding planes.

Jan 1, 1993

By Unto Paakkinen

The testing of different kinds of process flow configurations and cell volumes in industrial scale flotation processes is in general difficult to accomplish and even expensive to perform.1 Also the lack of suitable measuring and analyzing devices often prevents effective comparison of results. Nowadays, the existing flotation processes contain, almost with exception, several return loads which result in difficult control of the process. There exist two good reasons for testing different kinds of flotation circuits at the Outokumpu Oy Kotalahti mine. Firstly it is easy to change the process flow configuration without any additional installation work and secondly, the concentrator is highly automated with magnetic flow meters, on-line analyzer and process computers. In this presentation, open circuit flotation is compared with the classical closed circuit flotation which contains return loads. In additional, the effectiveness of computer control in both cases is estimated and also the effect of cell volume on flotation results is examined.

Jan 1, 1977

By Kunio Hashimoto

The conventional troughed belt conveyor system is the most widely used form of equipment for transporting bulk materials in the world today. The reason is not only because it is possible to transport a great deal over a long distance when compare to other types of equipment but also due to its greater economic efficiency and low initial and running costs. When dry, powdery materials and liquid materials are being conveyed, there are enclosed transport methods such as flow, case, air-slider and pipe line. In addition to features of the belt conveyor, a system employing a pipe line to transport dry powdery and liquid materials has always been considered an ideal method. This has been brought into reality through the Pipe Conveyor Sys tem.

Jan 1, 1984

By K. L. Bickel

Catalyzed diesel particulate filters (CDPFs) are used for reducing diesel particulate matter (DPM) concentrations in underground mines. The U.S. Bureau of Mines is conducting research on how catalyzed diesel particulate filters perform. Two CDPFs, with two different catalysts, are used on vehicles in two mines. The CDPFs are periodically removed from service and evaluated in the laboratory to determine their DPM collection efficiency, regeneration temperature, and effects on gaseous hydrocarbon (HC) and carbon monoxide (CO) emissions. This report summarizes the results of the laboratory evaluation, and the mines' experience with the CDPFs. Both CDPFs have operated over 2,000 h. One was evaluated after 1,646 h; its collection efficiency at one operating condition was 87.3 pct. After 2,135 h of operation it was removed from service because it was damaged. The second CDPF continues to be used after 2,328 h of service. The laboratory evaluation indicated its collection efficiency decreased after 1,584 h of use and its regeneration temperature increased from 405' C to 420' C. The mines' experiences with the two CDPFs varied. While being used on mine vehicles, both CDPFs became plugged with DPM on a number of occasions because of insufficient regeneration. CDPFs are capable of lowering DPM concentrations in diesel exhaust. They can also lower emissions of CO and HC, depending on the type of catalyst used. In this study, the performance of the CDPFs changed with use. Recommendations are given in this report for proper use of CDPFs in mines.

Jan 1, 1994

By R. E. Vivas, J. A. Villa

"INTRODUCTION Located in the state of Colima, Peña Colorada is one of the largest iron ore operations in Mexico. The project is owned in equal parts by ArcelorMittal and Ternium. Though boasting a production capacity of 4.5 million tons of concentrate per year, Peña Colorada is faced with declining ore grades. In order to respond to this situation, Peña Colorada had to expand production even further. This expansion created various challenges that were overcome by the adoption and application of new technology. Examples of these technological innovations are discussed in detail in this paper and include improvements in geo-modeling, mine planning and mine operations. The successful implementation of these technologies paid for itself many times over, and has led to significant improvements in production and performance, while lowering the operating costs and reducing the variance between planning and execution. PROJECT OVERVIEW Peña Colorada is a mining company which produces about 30% of the iron ore in Mexico. This project generates about 1,200 direct jobs and 3,000 indirect jobs, making a significant contribution to the local economy. Similarly, Peña Colorada invests in its local communities through numerous educational programs, scholarships, university agreements, social development, environmental agreements, etc. Peña Colorada’s operations consist of an open pit mine located in Minatitlán and a pellet plant located in the port city of Manzanillo, as shown in the location map below:TECHNOLOGICAL INNOVATIONS Most mining projects around the world typically follow the logic of “mining the next best ore”. Consequently, head grades tend to decline over the life of the mine. In the case of Peña Colorada, a decline in head grade combined with a decline in iron ore prices forced the operation to adapt to a new business environment and adopt new technologies to face these challenges. However, the first step along this process was to increase the confidence and reliability of the resource model. This task involved additional drillhole campaigns coupled with more detailed modeling techniques. Once the block model was completed, new optimization studies and production schedules were evaluated with new optimization tools that unlocked significant project value in many aspects of the mine plan. Similarly, new geotechnical studies were prepared, which provided new guidelines for pit slope design, and new technology was implemented to monitor ground movement and slope stability. The picture below shows two sectional block model views in MineSight 3D, along with the pit designs and geologic solids"

Jan 1, 2017

By J. K. Shurie

Calcined high quality bauxite is a staple raw material of the abrasive industry world-wide. The author discusses the factors which affect the economic value of calcined abrasive grade bauxite, and proposes an approach to the problem of estimating the relative value of available materials.

Jan 1, 1990

By Haydn H. Murray

Since the advent of machine coated paper in the mid 1930's, the kaolin industry has had a remarkable growth, In 1935 the domestic production of kaolin was 500, 000 tons and in 1970 the estimated production was in excess of 3. 5 million tons. The process industries which use kaolin most extensively are paper, rubber, paint, ceramics, plastics, catalyst manufacturers, ink, and pharmaceutical. The paper industry is by far the largest consumer of kaolin using approximately 70 per cent of the total tonnage mined and beneficiated. Up until 1970 the major kaolin producers were able to expand rapidly enough to supply the demand but for the first time in thirty years the demand is expected to be in excess of mining and beneficiation capacity through at least 1975. The major reason for this is the expansion of coated paper production in Europe and Japan. Two areas supply the lion's share of kaolin for the world markets. These are the Cornwall area in extreme southwestern England and a limited area of Georgia and South Carolina in the southeastern U. S. The English kaolins are primary - (found in decomposed granite) whereas the Georgia-South Carolina kaolins are secondary - (found in lenticular, continuous beds in the Tuscaloosa formation of Cretaceous age. ) The English kaolins are mined by hydraulic methods whereas the Georgia-South Carolina kaolins are mined by dragline or shovel and benefidated by using a wet process for the majority of the production and/or a dry

Jan 1, 1971

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of US coal companies are developing seams previously considered too deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas in coal beds increases with depth, and ventilation requirements are much more stringent for deep mines than for shallower mines. When the longwall mining method is wed at great depths, ventilation, ground control, and operational considerations all influence the design of longwall panels. This paper examines these influences, particularly ventilation and operational considerations, on the feasibility of two-, three-, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1988

By W. S. Sanner

Experiments were conducted to determine the quantity and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. A low-, a medium-, and a high-volatile anthracite were studied. Specific gravity separation followed by grinding, screening, and refloating at lighter specific gravities yielded small quantities of material purified to 1.0 percent ash, as follows: From low-volatile anthracite, 0.7 percent; from medium-volatile coal, 1.0 percent; and from high-volatile coal, 2.3 percent. The reduction in ash had no appreciable effect on the volatile matter or sulfur content of the coal. The limited quantities of material containing 1.0 percent or less ash obtainable indicate that if ultraclean coal is desired, a practical approach should include the processing units as an integral part of a conventional dense-media washing plant.

Jan 1, 1968

By Bo-Hyun Kim, Mark K. Larson

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) have advocated the use of instrumentation in underground mine ground control studies to aid in understanding failure mechanisms and to calibrate numerical models. The purpose of these efforts is to reduce accidents and fatalities in underground mines resulting from inadequate design of mining layout or supports. A recent examination of some results of stress change measurement raised some questions about the validity of elastic solutions in ground, such as coal. Particularly under deep cover as is prevalent in the western United States, the coal around a borehole would likely have yielded so that post-yield behavior would govern the response of the instrument.A numerical experiment was conducted by NIOSH researchers using the FLAC software (Itasca Consulting Group, 2016) to investigate the response of the borehole pressure cell (BPC) and the biaxial stressmeter to varying degrees of plastic behavior. The pre-encapsulated BPC cell pressure exhibits increasing departure from the elastic case with decreasing post-peak-strength slope of the stress-strain curve. On the other hand, because the BSM usually provides much more confinement to the surrounding rock than does the BPC, the measurements obtained from the BSM do not depart significantly from the changes in secondary principal stresses and directions as calculated by the elastic solution.INTRODUCTIONSeveral years ago, Larson et al. (2000) described several instruments that NIOSH had used in underground field studies and how to monitor them with dataloggers. This information is still relevant because of the need to understand how excavation affects the stability of mines and thus, the safety of mining personnel. One class of instruments described in that paper includes those instruments that measure change in rock stress. Although several such instruments might be used to measure stress change, the focus of this paper is on two instruments with which NIOSH has had more recent experience—the borehole pressure cell (BPC) (Geokon, 2018a; RST Instruments, 2018) and the biaxial stressmeter (BSM) (Geokon, 2018b). Other instruments, such as the CSIRO hollow inclusion stress cell (HICell) (Earth Sciences, 2019; Worotnicki and Walton, 1976) may be included in future studies.Early studies in the development of the BPC were those of Panek and Stock (USBM, 1964), Sellers (1970), Lu (1984), and Babcock (1986). Babcock’s work is particularly useful, but his setting and testing range was far below what we experienced in the NIOSH study, and it was Babcock’s data reduction scheme from his laboratory experiments that was used to calculate stress change in the NIOSH study (NIOSH, 2019a)."

Jan 1, 2019

By K Louie

When BHP Copper's Lower Kalamazoo Project commenced production in January 1997, two of the four original hoists had been converted to hoist ore from the Lower K level. Conversions on these hoists not only allowed hoisting from a much deeper level, but also created a higher hoisting efficiency and higher capacity as well. Conversions included new drums, new cables, SCR drives and other solid state control technologies not available when the original hoists were installed. Two of the original hoists were installed in the 1950's and the other two were installed in the 1970's.

Jan 1, 1998

By J. J. Kellar

The near-infrared (NIR) (12,000-4,000 cm-1) region of the electromagnetic spectrum, between the mid-infrared and visible, has often been viewed by spectroscopists to be of limited utility. This is unfortunate, and recently the use of the NIR has increased greatly, primarily for the quantitative analysis of food and agricultural products. However, many other areas of application of NIR spectroscopy remain unexamined. In this paper a novel use of NIR in the area of flotation chemistry is demonstrated. Specifically, it is shown that NIR/Internal Reflection Spectroscopy (IRS) can be used to quantify collector adsorption reactions in-situ.

Jan 1, 1990

By M. Dondi, M. Surracco, G. Alfano, P. Saba

Recent investigations on fine grinding with jet mill miprototypes of original design, constructed at the DIMM and Centro Studi of the National Research Council at Cagliari University, have led to the realization of a third generation micronizer characterized by large capacity and high efficiency. The new model and its distinctive features are described here and the results are presented of grinding tests on typical, high grade Sardinian minerals used for quality products. The operating principles of the jet mill are described in relation to the mechanico-elastic properties of the minerals treated. In particular the efficacy of the comminution process is demonstrated in terms of both solid treated and of impact, attrition and shearing forces generated in the micronizer. Particle size distribution of the finished products are reported, that satisfy the most stringent market specifications for the different minerals, as well as energy consumptions. The alternative operating options for solving particular grinding problems and minimizing energy consumption are discussed. Lastly, the main developments of the jet mill for a possible application at industrial scale are suggested.

Jan 1, 1995

By A. Halim, A. Martikainen, S. GYAMFI

This paper outlines a unique case of the development of strategies to reduce ventilation and heating costs in Konsuln iron ore mine in northern Sweden. The mine, located just south of Luossavaara-Kiirunavaara Aktiebolag’s Kiruna iron ore mine, was developed as a test mine from 2018-2020 for the Sustainable Underground Mining (SUM) project. Besides functioning as a test mine, Konsuln also contributes to ore production. The existing mine ventilation system was designed for the current production rate of 0.8 million tons per annum (Mtpa). There is a plan to increase this rate to between 1.8 and 2.0 Mtpa.

Dec 23, 2021

By Z. D. Hora, W. N. Hamilton

Evaporite units of the Western Canadian Sedimentary Basin are known to host native sulfur. In British Columbia, a large number of oil and gas exploration drilling holes reported intersections with native sulfur. The most important ones include 6 meters (20 feet) and 27 meters (90 feet) of native sulfur among 23 occurrences in Devonian Muskeg evaporite or adjacent Slave Point reef facies carbonates. A small Frasch sulfur deposit is known from Devonian Wabamun Group sediments near Camrose in South Central Alberta. Occurrences of native sulfur are common also in association with presently mined gypsum of Devonian Burnais Formation in southeastern British Columbia. Triassic sediments with evaporite members in British Columbia are also known to contain native sulfur showings. A widespread presence of anhydrite in many sedimentary units of Alberta and British Columbia together with oil and gas fields in the same areas and associated native sulfur occurrences point to a possibility for Frasch sulfur deposits in this part of western Canada.

Jan 1, 1992

By M. Galetakis

The difficulties that rise during the evaluation of multiple-layer lignite deposits come from the deposit structure (alternating lignite layers with intercalated material of varying thickness), as well as from the limitations of the applied selective mining. Thin layers of lignite and interbedded waste layers are grouped under specified assumptions regarding thickness and ash content, to form the exploitable blocks. However, in practice the decision for excavating a block is made under subjective constraints of different importance or by using uncertain data. Advances in Fuzzy Inference Systems (FIS) have provided a new approach to the evaluation of multiple-layer lignite deposits. FIS have the ability to handle imprecise or incomplete or linguistically ambiguous information and to incorporate them into decision-making processes. In the developed FIS (Mamdani type) new linguistic variables, concerning with working conditions, operators? experience and production were involved. The FIS was used for the estimation of quality characteristics and reserves of the exploitable lignite produced from Southern Field mine, Ptolemais (Greece).

Jan 1, 2005

By V. G. Hill

The term bauxite was first used by O.P.A.P. Dufrenoy in 1845 for an ore which was discovered by Pierre Berthier in 1821 near the village of Les Beaux de Provence near Arles in southern France. His data suggested that this mineral was an alumina hydrate with two molecules of water. However, it was subsequently shown by thermal analysis that the mineral was a fortuitous mixture of the mono-hydrate and the tri-hydrate. Diaspore had been previously discovered in 1801 and gibbsite in 1822. The term was however retained as a rock name. The name of the village was changed to Les Baux around 1885; Sainte Claire Deville suggested that the mineral name should reflect this, and it was changed to bauxite (Bracewell, 1962, Rkgnier, 1988). Mining of bauxite began around 1860 in the Auriol region in the Bouches du Rhine area in the south of France. This ore was transported toMarseilles by carts and was processed in the Salindres plant, which at that time was the only plant producing alumina using the Deville process and aluminum by the chemical process. During that period white bauxite (low iron content) was particularly sought after for the production of aluminum sulfate, refractory bricks, and quick setting cement. Export of bauxite from France began in 1880 and was initially delivered to Chemische Fabrik, Goldschmischen near Breslau, and to Guilini's Ludwigshafen plant in Germany in 1885. These companies produced alum and aluminum sulfate (RCg- nier, 1988). The next bauxite mining operation was in Antrim County in Northern Ireland in 1873. This was first used for the manufacture of alumina refractory bricks and quick setting cement (Bracewell, 1962). It is important to emphasize that initially almost all of the bauxite which was produced came from France and was mainly used for non-metallurgical purposes. At that time even the production of alumina was mainly for use as a mordant in textile dying. However, with the development of the Hall-Héroult process, the alumina which was available was increasingly used for smelting to aluminum. In spite of this the demand for non-metallurgical bauxite continued to increase and a set of applications were developed. These include refractories, abrasives (including the recently developed proppants), high alumina cements, aluminum chemicals, activated bauxite, and alumina. It became increasingly evident that the high alumina-low alkali raw materials have special advantages. The question however was one of cost benefit. Chin (1989) has pointed out that the non-metallurgical operations have been traditionally grafted on a bauxite/alumina/aluminum industry tree. In this context the non-metallurgical alumina produced was, with few exceptions, regarded as either coproduct or byproduct i.e.: Bauxite Trunk Sector Alumina Trunk Sector Aluminum Trunk Sector

Jan 1, 1994

By Hillary W. St. Clair

In a previous report 1/the author showed that the essential information from particle size analyses of grinding mill products can be represented by three or four parameters derived from the first four moments of the particle size data. These parameters may be used in gamma or beta distribution functions to estimate the weight fraction in any given size range. Moment analysis was used to study the progressive changes that take place in particle size distribution when a homogeneous isotropic mineral such as quartz is reduced in size by impact crushing. 2/ This report briefly reviews the essential features of moment analysis and describes extension of this method to size reduction by ball mill grinding.

Jan 1, 1972