Search Documents

By A. Bergmann

Location The Meggen Mine and the concentrator plant of the "Sachtleben Bergbau G.m.b.H." are located in the southern part of the Ruhr-district of the Federal Republic of Germany. The mine has been in operation for more than 100 years, but the concentrator described in this paper was built in 1962 and started up in January 1963. Goelogy and Mining The Meggen ore-body is of sedimentary origin and occurs in a zone of limestones, graywacke and shales of Devonion age. The average thickness of the deposit is 3 meters and, due to an intense folding of the area, the mineralized zone dips very steeply at 800 toward the north. The ore consists of 85 percent of sulfides and 15 percent gangue that mainly contains silicates from the host rocks. The principal ore minerals are pyrite (67 percent), sphalerite (16 percent) and galena (2 percent) with minor amounts of marcasite and only traces of chalcopyrite. As shown in Fig. 1, the sphalerite and galena are very finely disseminated in the massive pyrite of the Meggen ore, and a very fine grinding combined with a special flotation technique are required to liberate the valuable sulfides and to produce separate concentrates of lead, zinc and pyrite. Mining is performed by the sub-level stoping method and employs trackless equipment. Present operations provide ore from the 600 meter level. Annual ore production is 870,000 metric tons.

Jan 1, 1972

By M. Fig, B. Treffner, J. Brune, C. Strebinger, G. Bogin, D. Pardonner

"Methane gas explosions in a longwall coal mine can originate from in or around the gob and can seriously harm nearby workers and equipment. In order to fully understand the explosion flame and pressure wave propagation in the mine, it is important to investigate methane flame propagation in confined spaces as well as flame interaction with rock rubble and other mine structures. The latter can lead to enhanced turbulence causing high-speed deflagrations and/or detonations. Researchers ignited methane-air mixtures in horizontal, cylindrical reactors that contained inserts to simulate various gob characteristics. Rock surface topology and ignition location were investigated. Results show rock surface roughness increased fluid motion, thereby increasing methane flame front propagation velocity, overall pressure rise of the explosion, and time of pressure decay. Moving the point of ignition away from the open end of the reactor resulted in an increase in peak overpressure and an overall pressure rise of the explosion. Experiments were used to validate a computational fluid dynamics (CFD) combustion model that will be incorporated into a mine-scale explosion model to simulate and predict explosion hazards of large scale methane gas deflagrations in longwall coal mines. INTRODUCTION Coal mining is an integral part to our global society with coal-fired power plants providing about 40% of our global electricity [1]. A common method of extracting coal underground is by longwall mining. Researchers and investigative reports have found that explosive gas zones of methane-air mixtures can form along the longwall face and within the longwall gob, presenting an explosion risk to nearby workers and equipment [2]. In an explosion, the resulting flame and pressure wave presents a fatal traumatic injury hazard and can cause serious damage to equipment. In order to evaluate and mitigate the explosion risks in longwall coal mining, researchers at the Colorado School of Mines are developing a coupled CFD and combustion model of a longwall coal mine. The purpose of the model will be to better predict the explosion hazards under various mine conditions in order to build stronger prevention and mitigation strategies for miners."

Jan 1, 2018

By Prakash C. Kapur

A principal first order and a minor summation term contribute to the solution of the discretized batch grinding equation when formulated in cumulative retained mode. Depending on the interrelationships between the selection and breakage parameters, the minor term may be advantageously modified in a number of ways. The reduced grinding equations thus obtained are solved by iterations to give relatively simple solutions which are tested against experimental data. The implications and advantages of the reduced grinding equations are briefly discussed.

Jan 1, 1969

By Iga Trisnawati, Fitria Puspita, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Idi Amin, Andi Nurfaadhilah Ulfah

Laterite ore is a valuable resource due to its high content of metals essential for modern technology, including nickel, iron, and cobalt. However, extracting nickel from laterite ores is challenging due to their complex mineral composition and low nickel concentrations. This study examined the leaching behavior of pre-roasted laterite ore and the effect of roasting on leaching kinetics. The ore was roasted at temperatures of 280°C and 610°C for 3 h, followed by sulfuric acid atmospheric leaching. The results demonstrated that pre-roasting at 610°C significantly enhanced nickel leaching recovery, with up to 93% nickel successfully recovered. The leaching process of pre-roasted laterite ore was found to be controlled by diffusion through the ash layer, with activation energy values of 20.97 and 18.97 kJ/mol for laterite roasted at 280°C and 610°C, respectively. These findings indicate that pre-roasting can improve the leaching performance of laterite ore, potentially leading to more efficient and sustainable nickel extraction processes.

Feb 27, 2024

By Bryan Ulrich

On March 20, 2014, the ?Roundtable Discussion on Innovations in Heap Leaching and Mine Waste Management? was hosted by Knight Piésold and Co. at the Red Lion Hotel in Elko, NV. This topic is timely, and formed something of a lead into the inaugural ?Workshop on Innovations in Waste Rock, Tails and Heap Leach Management.? That workshop, which grew from the 2013 Elko Roundtable, was held on the University of Nevada, Reno (UNR) campus on May 19, 2014. The workshop was hosted by UNR and the University of British Columbia. Knight Piésold?s local representatives, Bryan Ulrich and Logan Jensen, were joined by Tom Kerr, president of Knight Piésold?s, U.S. practice; Rick Frechette, senior vice president, environmental services and Jeff Coffin, geotechnical engineer, from the Denver, CO office for the roundtable event. The event played host to about two dozen attendees from several western states.

By Jr. Zink

An economic and operational evaluation of the unrecovered metal, physical conditions, and chemical environment in a leach pad should be made prior to decommissioning. This evaluation will help determine the possibility and method of secondary and/or enhanced metal recovery and the method(s) to be used for detoxification and heap closure. The evaluation requires quantitative sample collection in a locally variable, yet grossly homogenous material. An assessment of a valley fill heap leach pad was made using a technique borrowed from placer technology called sonic drilling. The sonic drilling technique produced very satisfactory core recovery and sample quality. At this site, drilling results demonstrated that the method of heap construction produced expected features after extensive long term leaching. Rather than a uniformly homogenous pile of metallurgically depleted crushed ore, an assemblage of solution channels, un-oxidized sections, unleached areas, and compaction due to various factors, were found. These conditions are thought to represent a normal, rather than unique, situation for a valley fill heap leach. The lack of this information can have a significant impact on the economics and methods of heap re-handling and ultimate closure.

Jan 1, 1992

By H. Wen

"Taking the long flame coal, gas-fat coal and anthracite as samples, we tested the adsorption quantity to single component gas of N2, CO2 and CH4 under atmospheric pressure phase at different temperatures. Then we analyzed the adsorption characteristics and models of different metamorphic coals. The results show that metamorphic grade, temperature and gases species are main factors to adsorption quantity of coal. The higher and lower metamorphic grade of coal have greatly influence on adsorption capacity while moderate grade of coal has opposite result. The coal adsorption amount to three single component gases under the same experimental condition is CO2> CH4> N2.The simulation precision order of four adsorption models is quadratic curve model > Freundlich isotherm model> Langmuir model >logarithmic curve model. Quadratic curve model and Freundlich isotherm model both can accurately describe the adsorption behaviors of N2 and CH4, different isothermal adsorption curve of CO2 needs two kinds or more models to describe. This has a reference value to the study of adsorption characteristics and models to single component gases.INTRODUCTION Adsorption is the interfacial phenomena that concentration of single or multiple components in the interface layer is different from the bulk phase (1964). Adsorption model is mathematical models to describe the adsorption characteristics of the adsorbent, mainly reflected to fitting effect of gas adsorption isotherm, which contribute to deeply understand the adsorption characteristics of adsorbent. Many scholars have carried out extensively experimental studies of the coal adsorption process from different angles. Zhao (2010) studied the influence of coal metamorphism to pore development of coal seam through a variety of experimental methods. Zhang (2006) analyzed the adsorption capacity and the controlling factors from three aspects of the coal rank, maceral and coal mass deformation. Cheng et al., (2002) studied the influence of pore size distribution of different rank coals to adsorption constants. Zhong (2002) carried out varieties of isothermal assay and established the prediction method of coal seam adsorption affected by a variety of conditions. R. M. Bustin (1998) proposed that we could not simply describe the change law of coal adsorption capacity and maceral content by a fixed parameter, and the adsorption capacity of the same coal rank also has great change. C. R. Clarkson et al., (1997) used four different adsorption models to describe the coal methane adsorption process, and the fitting precision of adsorption models is D-A equation >D-R equation > BET equation> Langmuir equation. Gasem, K et al., (2003) found that the fitted isothermal adsorption curve of D-A equation and BET equation are better than Langmuir equation under high pressure condition, while D-R equation and BET model are better to CO2 adsorption. In recent years, scholars’ at home and abroad research achievements of coal adsorption focused on high-pressure stage (about 0~15 MPa), mainly for coalbed methane exploitation, carbon dioxide trapping and sealing technology development, but the study of coal adsorption under atmospheric pressure phase is little. In this paper, we analyzed the adsorption characteristics and models under atmospheric pressure phase, it has a reference value to the study of characteristics and models to single component gas."

Jan 1, 2015

In some 35 years in the explosive and construction industries, we have probably seen the extremes in drilling and blasting practices. All of you know that it is difficult if not impossible, to separate those two operations, particularly when we are searching for an optimum. Early in my career while doing engineering survey work for a major cross country pipeline construction company, we witnessed some of the wildest blasts imaginable, and they were wild for two reasons. Both the drill hole diameter and the drill pattern were such that when loaded with explosives, the factor in terms of pounds/cu. yd. was extremely high. On the other hand, in 1982 we were in an underground coal mine where just one hole was used to prepare a 20-ft. (6m) wide face. In this coal mine, they brought down 7 yd3 (5.35m3) of coal with just 1 lb. (.454 kg) of explosive. On a pipeline job, the factor may only be .1 yd3 per lb. of explosives. Open pit operations in the same geographical area may have almost the same type of rock, but similarities could end there. The several operators over the years will have installed different size-crushing equipment or variances will exist in other facets such as drilling, excavating, and haulage units. That tells us that if we have 6 operations in that common area, we are faced with a fact that there is an optimum drilling and blasting pattern for each of those six. We start at that point. We will note from Figure No. 2 the simple equations for determining either cu. yds. or tons. For a rock heavier than limestone, it may require only 10 to 11 cu. ft. (.31m3) for 1 ton (.91 metric ton) of rock in place.

Jan 1, 1986

By James D. Cooper

Technologic advances in materials utilization during the past two decades have brought is a long way toward the point where we can make the products we need from the materials we have readily available. Notable examples are the synthesis of diamond, zeolites, quartz crystal, mullite, and mica, and the development of phosphate bonded tale. Two of these--zeolites and mullite--involve the use of clays. There is little reason to doubt that equally important advances will be realized in the next decade, and that clays will play an important role in the developing materials technology. Indeed, the stage is already set for many of them. This discussion is concerned primarily with the high quality, relatively high priced clays, kaolin, bentonite, fuller's earth and ball clay. The first three have enjoyed demand growth rates over the past two decades which on the average exceeded the growth rate for the economy as a whole. There are indications that demand for ball clay will be growing at a faster rate in the future.

Jan 1, 1970

By G. V. Sullivan

As part of its program to conserve domestic mineral resources through advancing mineral resources technology, the U.S. Department of the Interior, Bureau of Mines, conducted investigations to determine the feasibility of recovering high-grade barite concentrates, suitable for use as well-drilling mud, from current and old waste pond materials and materials bypassed in present mining operations. Flotation studies of waste pond samples from Missouri and Nevada yielded barite concentrates containing over 95 percent BaSO4 with recoveries of 86 percent and 96 percent, respectively, of the barite in the flotation feed. Flotation studies of a hard-rock sample from Georgia, currently bypassed in mining, yielded a barite concentrate containing 97 percent BaSO4 with an attendant recovery of 97 percent of the barite.

Jan 1, 1980

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By Richard Giffen, Martha Gross, Luca Pellegrini, Pa Ousman Njie

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in Virginia includes parallel 1.5- mile (2.4 km) tunnels constructed using a tunnel boring machine (TBM). The TBM launching and receiving shafts were excavated within the footprint of two reclaimed islands abutting the navigation channel for the Port of Virginia. The shaft excavations—a circular tri-cell shaft at South Island, and a circular-rectangular twin-cell shaft at North Island—were supported by slurry walls up to 190 feet (58 meters) below the island surfaces. This paper describes specic design considerations for these shafts, as well as construction and uality-oversight aspects of their excavation and construction.

Jun 23, 2024

By Thomas P. Meloy

Floating "fines" differs from floating "sands" because the fines have a much larger surface area compared to their mass. The forces that arise from this large specific surface the key to understanding the behavior and treatment of fine particles. Though the nature of these forces is not thoroughly understood, enough work has been done to give a qualitative picture of what is happening in a flotation cell. It is the purpose of this chapter to re-examine some of the more, recent theoretical work and-to indicate its importance.

Jan 1, 1962

By James S. Goff, Stephen J. Navin, Wesley W. Moulton

The White River Shale Oil Corporation (WRSOC), as agent for Phillips Petroleum Company, Sohio Shale Oil Company, and Sun Shale Oil Company, is developing a prototype oil shale facility on Federal Lease Tracts Ua and Ub, located in northeastern Utah and known as the White River Shale Project (WRSP). The Ralph M. Parsons Company (Parsons) has been retained as the design engineer/constructor for the project. This paper covers the successful pregrouting of the Bird's Nest Aquifer in conjunction with the sinking of a 9.2-m (30-ft)-diameter shaft and driving of a 3.89-m by 5.64-m (18.5-ft by 12.75-ft) decline. The Bird's Nest Aquifer derives its name from the ellipsidal solution cavities caused by leaching of random-size nacholite nodules. The sodium bicarbonate nodules occur as persistent bands within a matrix of siltstone and marlstone. The team, made up of the owner, engineer/contractor, and subcontractor successfully grouted the shaft down to an inflow of less than 0.06 lps (1 gmp) and the decline down to less than 0.12 lps (2 gpm) by injecting a total of 213.190 kg (470,000 lb) of Celtite Terraseal, 113,400 kg (250,000 lb) of limestone dust, and 41,730 kg (92,000 lb) of cement into the formation.

Jan 1, 1985

By LaPoint D. J.

Copper deposits in sandstones are excellent targets for open pit mines using SX-EW extraction and processing methods. The mineralogy consists of chalcocite as the primary sulfide and copper carbonates and sulfates in the zone of oxidation. Two general deposit types are recognized: early diagenetic copper deposits that are associated with the reddening of the surrounding sediments, and epigenetic deposits that are associated with the migration of copper-rich basinal fluids along faults into permeable reservoir beds with a source of reductant. Epigenetic copper deposits are more likely to contain enough tonnage to be economic.

Jan 1, 1996

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

By Danqing Gao, Brijes Mishra

Heterogeneity in rock formation affects both rock behavior and strength. Spatial variance of rock properties is an important characteristic of rock that addresses the heterogeneity of mechanical and physical properties and their effects on underground mining. Assessing spatial variance can be useful for locating potential difficult grounds and for performing reliability analysis in the mining support system. This study presents a spatially correlated, random model to investigate the influence of rock heterogeneity on rock strength and failure propagation. A random field database with specific spatial correlation was created for each physical-mechanical property using laboratory data and the extreme value stochastic model in MATLAB. Based on the improved microscale random model, we considered one three-dimensional numerical model to study a mine operating in the Pittsburgh seam. The influence of random field data on entry roof was investigated. The realistic random field database added two scale-measured parameters from horizontal and vertical directions to control the spatial correlation length. A number of cutting sequences were also considered in order to identify the effect of spatial variance on roof behavior. The results show that spatial variance provides an accurate prediction of erratic roof falls in coal mines.

Rendering a solid hydrophobic and solid-fluid particle* attachment in flotation are recognized as not necessarily related (1,2). The attachment is governed by forces of attraction and repulsion which need to be considered. The induction time required for attachment after solid and fluid particle are brought into proximity (3-8) illustrates the point. Laskowski(8) showed that a reduced induction time favoured flotation but detected no change in contact angle, a standard indication of solid surface hydrophobicity. Induction .time is observed in fluid-fluid particle coalescence, there being called a rest time (9-11) The induction time phenomenon is related to the presence of a metastable liquid film (disjoining film (2)) of the continuous phase (water in flotation) which must thin and rupture to permit attachment. The lifetime of this film, which is governed by the rate of thinning and the probability of rupture with thicknesss, depends on a complex interaction of forces. Investigating these forces should help clarify the attachment process. Practical benefits would be improved understanding of slimes flotation (12,13) This paper is concerned with the role of the mobile fluid particle-water interface on the film lifetime, in particular, the role of time-dependent or dynamic interfacial properties resulting from deformation of this interface.

Jan 1, 1975

By M. S. Prasad

In earlier work it has been shown that paper filler clay products can be obtained from primary kaolin deposits of Minnesota. The objective of the current work was to reduce silica and iron contaminants and to maximize kaolin recovery to higher value products suitable for paper coating. This results in achieving a finer and cleaner product conforming to paper coating specifications. Cationic flotation and high gradient magnetic separation were used to remove free silica and iron, respectively, while attrition grinding and ultrasonics have been examined for particle size reduction. The results of this work are presented and discussed particularly with respect to application-oriented product properties. Budgetary estimates are presented for a 200,000 ton/year processing plant based on the process flowsheet developed and optimized by the study.

Jan 1, 1991

By P. Schmäh

Nowadays, small diameter tunnels are increasingly considered in pipeline projects as an alternative for sensitive crossings or when soil conditions limit the use of conventional pipeline installation methods like HDD. Safety concerns play a key role, especially for inner-city installations. Pipe jacked microtunnels and small segment lining tunnels can serve as casing tunnels if access is required during construction for the change of cutting tools in challenging ground conditions or for maintenance of the pipeline in operation. Small diameter tunneling solutions offer a high degree of flexibility for alignment design in terms of geology, length and radius.

Jun 13, 2021