Search Documents

By O. Porterfield, M. O’Kane, M. Endersby

BHP Iron Ore initiated research programs in January 1995 to develop long-term plans for decommissioning waste rock material at its Mt. Whaleback operation. More than 2 Gt (2.2 billion st) of waste rock were deposited during the past 30 years. Ultimately, a total of 4 Gt (4.4 billion st) will be deposited in waste rock dumps constructed near the open pit. The Mt. Whaleback operation is located in a semiarid climate adjacent to Newman, Western Australia. The primary research program includes the development of technology for the long-term performance of the waste rock dumps with respect to vegetation, slope stability, surface runoff, erosion and water infiltration. This paper focuses on the design and implementation of a cover system to prevent water infiltration to the underlying waste rock. Data obtained from a laboratory program and from soil-atmosphere modeling was used to design horizontal field test plots. The construction of the horizontal surface field test plots is discussed together with the field instruments installed to monitor performance. The cover system is designed to maximize infiltration during wet periods for subsequent evapotranspiration while minimizing surface runoff. The result is a near-zero net infiltration to the underlying waste material. An important feature of the design is the use of run-of-mine waste material as the cover material. Monitoring is in progress and will continue for at least two annual wet/dry cycles. The optimum cover system should minimize the net infiltration of water to the underlying waste rock while maintaining physical and ecological integrity for long-term performance.

Jan 1, 2000

By S. Chander

The results of an investigation to characterize the chalcopyrite/solution interface are presented. Several techniques including galvanostatic and steady state polarization, cyclic voltammetry and impedance spectroscopy were used. The results show that the dissolution of chalcopyrite is incongruent. Initially, at low potentials(<O.34V), iron species are released which give rise to the growth of an iron-deficient sulfide (IDS) layer. The dissolved iron might reprecipitate as a hydroxide layer depending on solution composition. Continued oxidation involves diffusion of species through the product layer. At higher potentials (>O.48V) further oxidation leads to dissolution of copper and sulfur species with a resultant breakdown of the IDS layer. The changes in properties of surface coatings resulting from various electrochemical treatments are discussed.

Jan 1, 1991

By Jürg Künzle

The use of the underground space has been a recurring issue in human history, whereas the reasons for building subsurface structures have changed over time. In the decades to come, the world will be marked by a variety of underground projects never before seen. This paper describes a series of characteristic challenges of designing and building underground freight transportation systems, with reference to the example of Cargo sous terrain, a privately funded underground logistics project in Switzerland. It provides an overview of contracting practices that allow these challenges to be addressed with success.

Jun 13, 2021

By G. C. Allen

Selective flocculation is used for the purification of clay minerals. Here we present data from a surface spectroscopic investigation into the polyacrylamides mediated selective flocculation of kaolin from an impure matrix. Use of X-ray photoelectron spectroscopy (XPS) was shown to offer a useful approach for investigating the observed selective separations. In particular, a new small area XPS technique was used to characterize, in situ, the differential competitive, f1occulant adsorption onto mixed kaolin/gangue systems.

Jan 1, 1998

By Halter L. Gould

Since the turn of the century there has been a marked increase in population, industrial and economic growth, and in energy requirements in the United States. During this time our energy needs have been met largely by natural gas and petroleum, but as our reserves of these materials are depleted, we are going to depend more and more on our large reserves of coal. The mining of coal for electrical power production has increased at a rapid rate during the past decade. Over half the coal produced in the United States in 1971 came from mines utilizing surface mining operations (Paone, et al, 1974). Surface mining is expected to increase as the rising cost of oil places more demand on coal for energy. About 57 percent of the coal reserves in the United States lie in the area west of the 100th meridian. About one-quarter of this can be mined by current surface methods. This would involve the disturbance of approximately 1.5 million acres (600,000 hectares). By the year 2000, projections indicate disturbance of about 200,000 acres, or 300 square miles, in the West. Mined areas receiving more than 250 mm of annual precipitation can usually be revegetated without irrigation if the spoils are properly shaped, the surface layer consists of suitable plant growth media, and proven techniques in rehabilitating disturbed rangeland are applied. Areas receiving less than 250 mm of annual rainfall or with high evapotranspiration rates pose a more difficult problem. Revegetation of these areas can probably be accomplished only with major inputs of water and good management (National Academy of Science, 1974).

Jan 1, 1978

By James N. Brentz

This paper deals briefly with the problem of efficiently selecting the most cost effective haulage truck. Problems and factors are identified that effect productivity and operating cost. Despite the sophistication of computerized vehicle simulation programs, there is a wide disparity in accuracy and methodology, particularly in dealing with the various elements of cost.

Jan 1, 1984

By J. Boldy

The discovery of the Delbridge massive sulphide deposit in the Noranda district of Quebec resulted from an appreciation of the significance of a mercury leakage halo as a litho-chemical pathfinder to blind ore, coupled to its location relative to a geologically inferred ore-bearing horizon within complex volcanic stratigraphy. Systematic sampling of micro-fractures present in outcrops delineated a diagnostic anomaly, drawing attention to an area considered prospective for buried ore. The massive sulphide deposit was subsequently found to be blind and topped at the 110 metre level.

Jan 1, 1984

By L. P. James, W. W. Atkinson

Utah has produced about 31.7 kt (1 billion oz) of silver, more than any state in the United States except Idaho. Several high-grade ore systems in Utah, where the mines are now closed, occur within large polymetallic limestone-hosted districts related to plutonic complexes. These mines fed several major lead smelters for nearly a century. Interaction of magmatic chloride-rich fluids with carbonate rocks localized significant bonanzas within these districts. A low sulfidation state was produced in the fluids by their passage through limestones. The Bingham openpit mine has also yielded more byproduct silver than other porphyry copper-molybdenum-gold systems. Away from exposed intrusive rocks, some large silver-only systems occur in Mesozoic sandstone and in caldera-related veins in volcaniclastic rocks. Thick permeable latest-Proterozoic basement metaquartzite sequences present beneath western Utah may have been important, as perhaps they were in the Coeur d&apos;Alene district of Idaho, in providing chloride and silver-rich ore fluids. However, it is clear that specific Tertiary magmatic events played an essential role in the evolution of the Utah silver-rich metallogenic province. The largest silver districts in the state are genetically related to Tertiary porphyritic plutonic rocks.

Jan 1, 2003

By B. M. Davis

Frequently ore reserve studies utilize samples from a series of drilling or other types of sampling campaigns. Sometimes there is a mix of sample types, say for instance, channel samples from underground workings and drill core from surface drilling. Since drilling, sampling, logging, and sample preparation protocols tend to change over time, there is always a question whether the samples give similar results that vary only by chance alone. The problem of comparing the various campaigns is complicated by the presence of spatial relationships among the samples. Geostatistical tests take the spatial correlation into account, but these tests may be complicated and cumbersome to implement. A comparison method based on familiar statistical graphics is presented which accounts for the spatial relationships. It allows comparisons to be made quickly by using simple statistical graphs such as scatterplots and boxplots.

Jan 1, 1996

The recent mine disasters in Australian coal mines have initiated an introduction of Self-Contained Self-Rescuer (SCSR) as component in the development of new escape strategies for miners. These self-contained self-rescuers are closed circuit, demand sensitive breathing apparatus that make oxygen available to the wearer for a nominal period of time. Their operation is completely independent of the surrounding atmosphere. Once properly donned, the SCSR can assist a miner to escape from an area containing smoke, toxic gases or an oxygen deficient atmosphere. The duration of a typical SCSR is usually taken at the point of complete collapse of the breathing bag which is accompanied by an increase in breathing resistance and inhaled levels of carbon dioxide. Because the oxygen consumption (V02) and the heart rate are correlated, a prediction of V02 and consequently the duration of an SCSR can be made by monitoring the heart rate. Thirty-seven volunteers participated in field simulated escape trials at four underground coal mines. The results from the field trials suggested that oxygen consumption depends on the heart rate, the body weight and exercise rating of the miner. All the volunteers were asked to fill out the questionnaires to evaluate the performance of the units. The miners indicated that they could tolerate the inhaled temperature without any difficulty to breathing resistance. A complete statistical analysis of the field results is also presented.

Jan 1, 1997

By H. E. Hawkes

Reconnaissance mineral exploration based on the distribution of ore metals in stream sediments has become a generally accepted method of mineral reconnaissance. This approach seems to work almost equally well in all climates and in all kinds of terrain, provided of course that the ore deposits being sought are exposed at or near the surface and are actively undergoing erosion. Nobody with any experience in the field would question the validity of the concept on which stream sediment reconnaissance is based. Considerable dispute does arise, however, when the subject of density of sample sites per unit area, or sample spacing, comes up for discussion. What is the optimum balance between completeness of coverage and cost? The tacit assumption is frequently made that a greater sample density necessarily leads to more complete coverage and hence a lower probability of missing an important discovery, without regard for the size of the stream sample or the topology of the drainage pattern. The purpose of this paper is to attempt to bring the problem of site selection in stream sediment sampling into better focus, and to present a formula that may help in planning reconnaissance programs.

Jan 1, 1976

By D. A. Augenstein

Operators of coal preparation plants use equipment such as large-capacity dump trucks and bulldozers to haul, spread and compact refuse material to conform to federal and state regulations governing the disposal of solid waste. For example, federal regulations require that refuse be spread and compacted in layers not more than two feet thick. If the refuse layers or piles have poor load-bearing characteristics, movement of equipment over them becomes extremely difficult. The increasing cost and limited space for the construction of settling ponds extensively used for fine refuse disposal are leading to the growing practice of dewatering the fine refuse by means of vacuum disc filters and combining the resulting filter cake with coarse refuse for waste bank disposal. However, this filter cake usually contains more than 25% moisture. Therefore, when it is combined with coarse refuse, the moisture level of the total refuse may become high enough to impair the load-bearing strength of the refuse. Precisely this problem and the attendant difficulties of moving heavy equipment arose when vacuum disc filters were installed at a preparation plant in West Virginia. Combining the moist filter cake with the coarse refuse generally results in a 12% moisture level for the total refuse at this plant. At this moisture level, the refuse can still be handled with some difficulty by the equipment. However, the problem has frequently been compouned after rains.

Jan 1, 1977

By L. Martins

To increase zinc recovery in the concentrate, this investigation performed mineralogical characterization, dispersion studies, bench and pilot-scale flotation experiments and an industrial flotation trial. The objective was to verify the flotation behavior of the silicate zinc ore (calamine type) in the presence of slimes, with the aid of dispersing agents. Characterization studies identified the major minerals in the flotation feed as hemimorphite (calamine), quartz and dolomite. Dispersion tests showed that enhanced dispersion of the particles in the pulp in the absence of reagents occured at a pH range between 8.5 and 12.0. Bench-scale flotation experiments were planned using the statistical tool of complete factorial design at two levels, replicated once. These experiments showed, and were confirmed at the pilot-plant scale, that higher doses of sodium sulfide and polymeric dispersant combined with sodium silicate favored a higher metallurgical recovery. At 6,800 g/t (218 oz/st) sodium sulfide and 6,992 g/t (224 oz/st) polymeric dispersing agent combined with sodium silicate, a zinc grade of 38.4% in the final concentrate was achieved, at an average metallurgical recovery of 72.4%. The industrial trial confirmed the pilot scale results, leading to zinc recovery of 76.1% and a 37.3% zinc grade in the concentrate. Key words: Froth flotation; Flotation reagents; Flotation depressants; Zinc/ zinc ores

Jan 1, 2010

By E. F. Draskovich

In 1984 a high temperature heat recuperation system was installed in the pellet plant of the National Steel Pellet Company located in Keewatin, Minnesota. The system is similar to those of Cleveland Cliffs Empire and U.S. Steel&apos;s Minntac operations. It recovers hot process air from the cooler by induced flow, and directs it to an intermediate zone between the drying and preheat zones on the grate machine. This system recently underwent further modifications in April 1985, following initial operation in 1984. The M. A. Hanna Company, which manages the property, developed the design criteria and made the subsequent recommendations for modification through its research facility in Nashwauk, Minnesota.

Jan 1, 1986

By Kadri Dağdelen, Matthew Deutsch, Thys Johnson

Nested pit analysis in open-pit long range mine planning is used to define approximate ultimate pit limits and an initial high-level schedule in the early stages of a project. Modern ultimate pit optimizers can solve for dozens, or even hundreds, of nested pits however often a smaller subset of pits which are evenly spaced with respect to contained tonnage are desired for downstream analysis. In situations where that pushback selection process must be automated, such as when performing sensitivity analysis, or when the best subset of pushbacks is required; an optimization procedure is warranted. This paper describes a dynamic programming algorithm for selecting pushbacks following nested pit analysis, which is performant and addresses a long-standing inconvenience faced by long range open-pit mine planners.

Jun 25, 2023

By R. K. Will

An inactive mining operation in northern California is known to be a source of acid mine drainage and heavy metals which have impacted adjacent creeks. Elevated concentrations of copper and zinc are a concern to aquatic populations, particularly steelhead trout and salmon downstream in the Sacramento River. Previous regional geological surveys of mineralization by the U.S. Geological Survey located and mapped outcrops of massive sulfides and gossan. Recent investigations indicate that a substantial amount of the metals in the local creeks are due to natural causes. The investigations include locating and mapping surface and subsurface minerals, soil and water sampling, and chemical analysis. Groundwater, seeps, and surface water were also sampled and analyzed. A water balance was conducted on a sub-basin level following delineation of surface water drainage and groundwater divides. A chemical mass balance incorporated metal concentrations and water volumes and was then used with other data to determine the contribution of metals from natural versus mining-related causes.

Jan 1, 1998

In this paper, response surface methodology was applied to optimize the experimental conditions for the wet grinding of synthetic rutile. The effects of parameters such as rotation speed, solids concentration and duration of grinding on grinding efficiency were systematically investigated and the process conditions were optimized, using a nonlinear regression model based on central composite design. The statistical analysis of the results showed that in the range studied, the grinding efficiency of synthetic rutile was significantly affected by the rotation speed of the conical ball mill. According to results from analysis of variance, the value of the determination coefficient (R2=0.9989) indicates that the predicted values are found to be in good agreement with experimental values. The optimized experimental conditions were as follows: a rotation speed of 350 rpm, a solids concentration of 27.31% and a grinding time of 50.31 min, respectively. Under optimum conditions, the predicted grinding efficiency of 94.79% is obtained. The experimental values from the validation experiments were well within the predicted value of the model.

Jan 1, 2011

By P. R. Taylor

A reaction is evaluated by which heated and pressurized water is used to precipitate metal oxides from loaded Kelex 100 complexes. Pure copper oxide (CuO) and pure nickel (Nio) in powder form, and ranging in average size from 12 to 25 micrometers, were found to precipitate from copper and nickel loaded Kelex 100/kerosene complexes, by water heated and pressurized to between 374 and 400 °c and 2170 psig (148 atm) and 3500 psig (238 atm). The precipitation is suggested to result from hydrolysis of the metal, following exchange for the hydrogen in the phenolic hydroxyl of the Kelex 100 structure, enhanced by the conditions provided by heated and pressurized water. The reaction is believed to have the characteristics of homogeneous nucleation and heterogeneous growth. The effects of temperature, pressure, initial metal concentration and seed addition on the kinetics of the process were studied. In addition, characterization studies were performed on the reaction products. A detailed discussion of the experimental results is presented.

Jan 1, 1992

By R. M. Enick

A novel liquid-liquid separation for the recovery of free or liberated gold from mixtures of fine particles was evaluated. The separation, conducted at ambient temperature and a pressure of about 1000 psi a, was based on the difference in wettability of precious metals and minerals. Contact angle results indicated that in the presence of water and liquid CO2, gold, platinum and silver had intermediate wettability. Minerals such as quartz and magnetite, however, were hydrophilic. Therefore fine gold particles. -325 mesh, that were mixed with water and liquid CO2 dispersed in the CO2 or agglomerated at the H2O-CO2 interface while the minerals tended to remain in the aqueous phase. Best results were obtained when these fine gold particles were liberated, were not agglomerated in slimes, were not adhering to minerals, and were not coated with minerals.

Jan 1, 1998

By Martin G. Casto

Mixer-settler extractors, among the oldest forms of extraction equipment, have been used since the beginning of this century. Over the past years, a very large number of mixer-settler devices have been designed and operated. Both batch and continuous flow mixer-settlers have been used. The continuous flow mixer-settler extractor offers a great number of advantages over other extraction equipment. The main advantage of the continuous flow mixer-settler is that it is a compact device. A large number of stages can be assembled in a relatively small area, and more stages can be added fairly easily. Many improvements have been made in the design of mixer-settlers. These improvements occurred in almost every phase of mixer-settler&apos; operation; interface control, mixer design, intrastage pumping, interstage flow of the two liquid phases, and stage construction. It is believed that Barstow1 used one of the first continuous mixer-settler extractors. This mixer-settler had concurrent flow within each stage and countercurrent flow overall. The flow for both phases took place by gravity. The Barstow device and other early mixer-settlers had no separate interface control for each stage, therefore, "tilting" of the stages was necessary. In 1934 Holley and Mott2 designed a mixer-settler in which the heavy phase was recirculated within each stage by the use of a valve controlled central line instead of by a pump. Gordon and Zeigler3 in 1939 were among the first to use an adjustable valve to control the interface levels in a mixer-settler, making tilting of the extractor unnecessary. In 1952 Coplan et al. 4 used a modification of the Holley-Mott idea to build a highly improved mixer-settler with flat common walls, and with the

Jan 1, 1971