Search Documents

By Stephen H. E. Phillips, Michael J. Beus

A pneumatic impact breaker is used to fragment the rock at the shaft bottom, replacing the drill and blast cycle. A backhoe-type mucker removes the broken rock. The operators are in protective cabs below the bottom work deck in the shaft. Preliminary testing has been accomplished at underground and surface test sites in Arizona. Seven, approximately 6.4 m deep by 7.3 m-diameter (21 ft by 24 ft) test holes, (a total of 45 m (148 ft)), were recently excavated in various rock types, including jointed and massive quartz monzonite and rhyolite. An average advance rate of .4 m/hr (1.24 ft/hr) has been achieved. This includes breaking and mucking the rock. Further data is being sought from an in-shaft demonstration.

Jan 1, 1981

By J. A. González-Anaya

This laboratory work presents a study of the effect of ultrafine grinding on the gold recovery of a highly refractory gold concentrate. The particle size of the concentrate was P80 = 46 µm and the main species present were quartz (28.58%), dolomite (25.63%), pyrite (20.93%), arsenopyrite (15.39%) and 112 g/t gold. After optimizing hydrated lime and lead nitrate additions, standard cyanidation with 1% NaCN, pH = 12.3, 25% S/L permits to recover only 9.4% of the gold. Different particle sizes were submitted to cyanidation. When the concentrate was ground to ultrafine sizes (P80= 4.6 µm), the gold recovery for the same cyanidation conditions increased to 67%, with cyanide consumption of 66.7 kg NaCN/t. Additional tests were performed in order to reduce the cyanide consumption. The reduction of the cyanide concentration in the leaching solution from 1 to 0.5% and the addition of 100 g Pb(NO3)2/t allowed the reduction of the cyanide consumption to 27.6 kg NaCN/t (58% reduction), while maintaining the same gold recovery of 67%. The remaining gold could be present as very fine inclusions or in solid solution in the matrix.

Jan 1, 2011

By J. P. McKinney

A mathematical model is presented for the electrokinetic dewatering of suspensions of phosphatic clays. The modeling approach couples a boundary-element model for solution of Laplace?s equation to a recently developed constitutive equation that relates the change in solids content with applied electric field and time. The observation that the electric field controls both the maximum solids content achievable and the time required to reach that value is shown to severely constrain the application of electrokinetic dewatering strategies to an entire clay settling area. The approach, however, may be feasible for implementation as part of a continuous plant process.

Jan 1, 2011

By Katerina Adam

During wet grinding the electrochemical interactions between grinding media and pyrrhotite not only accelerate the media wear but also adversely affect the flotation response of the sulfide mineral. A possibility of remedying the adverse effect on its floatability by applying electric potentials to grinding media was examined. Flotation tests, Auger electron spectroscopy and x-ray photoelectron spectroscopy were used to study the surface properties of pyrrhotite. Although anodic polarization of the steels increased the metal loss by corrosion, the flotation recovery of pyrrhotite was increased. In the case of cathodic polarization, the flotation recovery improved in a narrow range of overpotentials. At higher cathodic overpotentials, however, the floatability of the mineral was progressively lowered although the corrosive wear of grinding media might be reduced.

Jan 1, 1984

By S. K. Kawatra

In many mining operations, particularly northern open-pit mines, large seasonal variations in grinding slurry temperature can occur. It is shown in this paper that this temperature shift can cause a winter-time loss in autogenous grinding efficiency of as much as 20Y. if it is not controlled. Laboratory experimentation indicates that much of this effect is due to increases in slurry viscosity as the temperature is decreased. An additional effect may result from changes in rock strength upon freezing, for which possible mechanisms are discussed. However, no effect clearly resulting from rock strength changes has been definitely confirmed.

Jan 1, 1990

By D. McElhinney, J. Winfield, G. Buchan, B. Slaker, A. Iannacchione, T. Minoski, G. Rashed, M. Van Dyke, M. Murphy

"The National Institute for Occupational Safety and Health (NIOSH) has previously established pillar design guidelines for the underground stone mining industry. These guidelines were created from an empirical database of pillar observations and were largely drawn from shallow, flat-lying mining operations. Current trends forecast a great amount of underground stone mines developing under deeper cover, higher seam dips, and more frequent multiple-seam mining configurations than in the past. The complex loading conditions and limited experience in these environments presents a substantial increased risk of ground failure. To investigate these loading conditions, NIOSH has installed a pillar and roof monitoring system at an underground limestone mine in central Pennsylvania. The mine is operating in a seam with dips ranging from 13 to 18 degrees and overburdens ranging from 275 m (900 ft) to 425 m (1,400 ft). Instrumentation installed in an undeveloped pillar and in surrounding strata is currently measuring pillar and roof behavior in response to stress redistribution during excavation. Laser scans are being used to measure ground displacement and changes in conditions associated with local mining conditions and significant geological features. Initial stress measurements show a gradual increase in stress in response to mining, and stress changes that correspond with blasts. The seismic system is operational, with calibration events signaling on each of the 18 sensors. INTRODUCTION Improving mine-wide ground control stability can help reduce the potential for catastrophic failure of underground structures. The National Institute for Occupational Safety and Health (NIOSH) has conducted prior research in stone pillar design and has established fundamental pillar design guidelines for the underground stone mining industry, which resulted in the development of the S-Pillar program (Esterhuizen et al., 2011; Esterhuizen and Murphy, 2015). The data that constitute the S-Pillar program were derived from past mining experience that was almost exclusively drawn from shallow, flat-lying, single-level mining operations1. Stakeholder interactions with NIOSH researchers have indicated that increased numbers of underground stone operations are expected to mine under significantly deeper cover, with greater seam dips, and under multi-level operating conditions (Slaker and Murphy, 2016). The complex loading conditions and limited experience in these challenging environments present a substantial increased risk of ground failure. Inadequate pillar design in these new and challenging environments could result in catastrophic wide-area pillar collapses and an increased safety burden to miners working in the U.S. limestone mining industry. To develop design guidelines and prevent inadequate pillar designs for these challenging environments, NIOSH is currently conducting detailed pillar response investigations at case-study mine sites operating in challenging environments."

Jan 1, 2018

By Jürgen Kretschmann

The European climate and energy framework for 2030 is highlighting the reduction of man-made CO2 by increasing the use of renewable energy to mitigate climate change. In this spirit, Germany has decided to erase the coal use as an energy source by 2038 completely. Inevitably, this strategy promises a feasible, responsible, and sustainable post-mining management, because 200 years of coal mining have created numerous challenges necessary to tend to once the mining ends. Thus, the Research Institute for Post- Mining (FZN) at the TH Georg Agricola University in Bochum, Germany, has developed a holistic approach to meet these postmining challenges including further expertise present at our university. Here, the four strategic research pillars are (1) technical geoecology and hydrogeology to avoid and mitigate risks underground, (2) geomonitoring to evaluate and protect the surface, (3) industrial heritage preservation and engineering to secure and reuse brownfields such as mine sites, and (4) economic transformation planning of mining regions to enable a prosper future for generations to come. In all efforts, we aim to achieve the fundamental goals of the UN to deal with the resources of our planet responsibly and sustainably. Furthermore, we are synergizing increasingly with national and international networks in the interest of social, economic, and environmental stakeholders.

Jul 23, 2020

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By N. Agron-Olshina

The application of the QEM*SEM image acquisition and analysis system to the measurement of the mineral matter in coal and the materials in fly ash is described. A new sample mounting technique was developed using iodinated epoxy to provide a backscattered electron contrast between the coal, the mounting medium and the mineral matter. Several comprehensive and detailed species identification programs for silicate minerals and materials were developed to analyse the 1000 count x-ray spectra used for the measurements. Case studies are presented to demonstrate the capabilities of the new technique to distinguish different coals and fly ashes by their mineral and material composition rather than by conventional chemical analysis. Applications of the new technique are aimed at demonstrating that composition and size distributions obtained from OEM*SEM measurements can be used: 1. to characterize coal with respect to combustion problems in power stations, 2. to characterize coal for fine coal cleaning, 3. to characterize fly ashes in relation to problems such as erosion in combustion systems and the ease of precipitability in dust collection facilities, 4. to refine the classification systems used in marketing coal for pulverized fuel firing and fly ashes as a component of cement and building materials.

Jan 1, 1992

By S. Corrent, F. A. V. Guimarães, M. G. Barbosa

"INTRODUCTION Moisture can be a villain, so new technologies have been explored to make more viable the production of high moisture iron ores. The current work presents the attempt of the utilization of a superabsorbent polymer (SAP) to aid in the screening process and in the ore handling process, such as stockpiles reclaiming and vessels/trains discharge in sub-zero temperature conditions. The results have shown that the polymer can be used in certain cases to improve productivity and increase safety in the process of handling the material (by increasing the TML). However, for size separation no advantages were found upon the use of the polymers. WATER ADSORPTION MECHANISMS The use of water in mineral processing is constant as its utilization brings an increase in the efficiency of separation. Although we have better results in the processing with water, materials with a high content of “natural” moisture can be very difficult to be treated by the conventional methods of separation. Nowadays many studies have been conducted in order to understand the effect of adsorption of water in the particles of complex minerals. Those studies have being divided in many different lines of research such as contact angle of a drop of water and the surface of the mineral to determine hydrophobicity, the particle size distribution and the porosity of particles. Mainly two forms of adsorption of water by the particles are possible: one the water is retained inside porosity of the particles. Laboratory tests developed in China have showed that capillary adsorption is faster in coarser particles that achieve the saturation degree earlier than finer particles (Xuewei Lv et al., 2011). The so called non-porous model considers the effect of water in the bulk sample of iron ores, in a physical connection when all the water works as a binder between particles as shown in the figure 1.If we take into account the compressibility of the system and compaction due to the weight of the bed over the particles, the thickness of the water film between particles is the same but the volume inside different particle size systems is much higher than in a system with particles of same size."

Jan 1, 2018

By J. Diao

In order to understand the flotation kinetic behavior of coal and associated mineral matter, a detailed investigation was conducted in a 2-liter Denver flotation cell using three high sulfur coals at three feed sizes, minus 28. 100 and 200 mesh. Subsequently. the flotation products were sieved into different size fractions and analyzed for their ash and pyritic sulfur content in order to delineate the effect of particle size on the rate at which each constituent floats. The results were tested with several different flotation kinetic models and the best model for coal was then chosen. The flotation rate constant and the ultimate recovery calculated from a kinetic model were used to delineate the effect of particle size, collector (dodecane) and frother (MIBC) dosages on the flotation kinetics of coal, ash and pyrite.

Jan 1, 1992

By L. J. Altenburg

There are a lot of key factors involved in achieving a successful Safety Program. I would like to discuss some of these factors and how they have played a major part in our success at Jacobs Ranch Mine. The areas I will cover concern: 1) Facility Standards (Corporate/Minesite), 2) Communication (Employee/Management -"Teamwork"). 3) Proper Training (Employee/Management). 4) Employee Attitude. 5) Incentive Programs. 6) Health Programs. 7) Results/Benefits.

Jan 1, 1994

By G. Kazonich

The high costs and environmental problems associated with making iron and steel in the United states is driving the development of new technologies to replace the blast furnace. A prototype reactor incorporating rocket technology was designed and built. This rapid rate reactor was operated successfully and consistently made iron metal. Minus 32s-mesh magnetite particles could be reduced to iron metal in less than 50 ms in a high temperature flow through reactor. Iron product was recovered inside the reactor and in a downstream cyclonic separator. The results of typical operation and how parametric changes affected the reduction of iron ore concentrates are discussed.

Jan 1, 1993

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By Casandra Gamez Gonzales, Angelina Anani

Copper, the newest addition to the critical mineral list, is an essential metal whose electrical and heat conductive properties label it as a vital mineral for the creation of renewable energy sources and the reduction of Greenhouse Gases (GHGs). However, despite copper’s leading role in the transition to sustainable energy and mining practices, the mining industry has faced various battles in the extraction of this valuable material. These challenges are based on mining’s negative reputation and extensive impact on the environment, nearby communities, and human rights. To ensure the survival of mining in the future and achieve mineral demands, an emerging topic that has initiated the revolution of the traditional sector into a more environment- friendly and transparent industry, is Environmental, Social, and corporate Governance (ESG). ESG has motivated companies to seek growth opportunities and standardize risk accountability and transparency based on its collective framework that creates, modifies, and implements local, national, and international standards. These standards focus on improving environmental, social, and governance issues faced by companies and their projects. ESG has served as a guideline that investors utilize to assess companies and promote sustainability, responsibility, and disclosure to create positive and balanced relationships with stakeholders and the environment. Nonetheless, concerns have been rising which state that ESG is negatively impacting the mining industry by targeting what fuels the industry and world: ore deposits and their resources. Therefore, this research focused on answering the following research questions: what are the impacts of ESG on the copper supply chain and how will stricter ESG standards affect future copper production?

Feb 1, 2024

By M. K. Boateng, K. Awuah-Offei

"Language barrier in a workplace affects workers’ productivity and safety. The objectives of this paper are to: (1) review the various approaches for breaking language barriers among miners; and (2) analyze the costs and benefits of these approaches, and make recommendations on the way forward. The authors achieve these objectives by reviewing the current approaches in breaking language barriers among miners. The review reveals that some of these approaches can be expensive with less benefits. Thus, it is concluded that mining companies should carefully select the optimal approach to break language barrier. INTRODUCTION Multi-national mining companies have expanded their operations into non-traditional mining destinations to grow and meet market expectations. For instance, Newmont Mining Corporation has about 14 operations and projects located in Africa, Asia, Australia and America (Newmont Mining Corporation Operations and Projects, 2015). Similarly, Freeport-McMoRan operates about 14 mines in North America, South America, Southern Asia, and Africa (Freeport-McMoRan Inc., 2015). Some mining companies have also attracted expatriate workers into their workforce. For example, Ma’aden, the Saudi Arabian mining company, in its 2013 annual report states that 34% of its total employees are expatriates (Ma'aden, 2013). Expatriates constitute a key source of skilled labor and facilitate skill transfer. The success of many international operations relies greatly on expatriate performance (Erbacher, D'Netto & Espana, 2006). Even companies that do not expand their operations into other foreign countries still have to deal with language barriers due to changing language demography of the country and the areas from which labor is sourced. For example, the language composition of the workforce and languages used in South African mines is diverse with miners proficient in Afrikaans, English, Zulu, Xhosa and others to varying degrees (Research Focus (Pty) Ltd, 2011). As a result of these trends, most mines today operate with a multinational workforce. This means cultural differences, including language barriers, exist among the miners. Marschan-Piekkari, Welch and Welch (1999) emphasize the fact that language problems become prominent as companies internationalize and grow their operations into more countries. According to a survey by Forbes, language barrier affects operations. For example, business owners acknowledge that language proficiency may promote a safer work environment (Rubin, 2011). A research has shown that language and cultural barriers in a workplace contributes to reducing workers’ productivity, increasing accidents, and hurts employers’ ability to recruit, hire and retain workers (Morris, 2002). Hence, mines are making efforts to break language barriers in their operating environments. Ma’aden, for instance reported in 2013 that 1,506 of its employees received training in English as a second language (Ma'aden, 2013)."

Jan 1, 2016

By R. C. Kellner

Duval Sierrita Corporation, a wholly-owned subsidiary of Duval Corporation, operates an 86,000 STPD copper-molybdenum concentrator near Tucson, Arizona. Shortly after production commenced in February, 1970, it became apparent that the reduction crushing system represented a limitation to reaching the design capacity of 72,000 STPD. The development work performed on the reduction crushers in order to first meet design capacity, and to subsequently increase production to 86,000 STPD is described in this paper. The Sierrita plant is a conventional three stage crushing sys- tem. All crushers were supplied by the Allis-Chalmers Corporation and consist of two 58 x 89 Superior gyratories, four 138b EHD hydrocones, and ten 384 hydrocones. Screening is performed prior to and subsequent to secondary crushing and in closed circuit with the tertiary crushers. Typical throughput rates and equipment sizes are presented in Figure No. 1.

Jan 1, 1975

By Madan M. Singh

This section is unique to the Handbook in that it is the only section that deals with underground excavations for nonmining purposes. The editors were of the opinion that the section should be incorporated because the subject matter covered by the chapters is closely related to mining, and many mining engineers are currently involved in these activities. As we enter the decade of the 1990s activities in this category will increase, enhancing the relevance and utility of the material discussed. As the population increases, especially in metropolitan areas, the necessity to go underground will be greater. At the present time, not only are subsurface shopping malls and pedways connecting buildings becoming commonplace, but structures as diverse as the Civil and Mining Engineering Building on the University of Minnesota campus, a road-and-fleet maintenance facility in Multnomah County, OR, and even an ice cream parlor (Dairy Queen) in northern Wisconsin have been constructed underground. Placing utilities below the surface has numerous advantages and is now customary. Rapid transit and highways through tunnels in urban areas have been the norm for many years, but subterranean stormwater reservoirs, power plants, industrial warehouses, and food storage silos are relatively new innovations. The philosophy of underground defense installations is ancient, but their requirements and designs have trans-formed radically as technology advances. The use of under-ground space for disposition of wastes is modern, since it is recently that environmental concerns and waste disposal costs have assumed increased significance.

Jan 1, 2008

By F. D. Ayhan

The aim of this study was to investigate desulfurization and de-ashing of a mixture of subbituminous coal and gangue minerals by the agglomeration method. For this purpose, experimental studies were conducted on a mixture containing subbituminous coal, pyrite, quartz and calcite. The effects of some parameters that markedly influence the effectiveness of selective oil agglomeration, such as solid concentration, pH, bridging liquid type and concentration, and depressant type and amount, were investigated. Agglomeration results showed that the usage of various depressants (Na2SiO3, FeCI3, corn starch, wheat starch) in the agglomeration medium has a positive effect on the reduction of ash and total sulfur content of agglomerates. It was found that an agglomerate product containing 3.03% total sulfur and 25.01% ash with a total sulfur reduction of 56.71% was obtained from a feed that contained 7% total sulfur and 43.58% ash when FeCI3 was used in the agglomeration medium. Key words: Desulfurization, De-ashing, Agglomeration, Coal, Gangue minerals

Jan 1, 2009