Search Documents

By J. R. Sims

Gold assays from production blastholes in the Mercur Hill Pit were used to delineate known ore zones and to determine how well previous exploration drilling defined these zones. The most important factors causing inadequate ore zone definition were: 1) inappropriate location of drill holes relative to the ore zones, 2) presence of stopes from previous mining, 3) sampling and assaying errors, and 4) smoothing of the ore zone boundaries during ore reserve estimation. Infill drilling strategies were evaluated to determine the efficiency with which a given drill pattern defined the known ore zones. A drilling strategy was developed which improved ore zone delineation when compared to techniques which maintained uniform drill spacing.

Jan 1, 1992

"Foreword by Ren BryceSenior engineer, Freeport-McMoRan, Oro Valley, AZ, USAThe eighth annual Mineral & Metallurgical Processing Division (MPD) student poster contest was held in February at the national SME Annual Conference & Expo in Denver, CO. A total of 33 students presented their work at the poster competition. The competition started in January when the students submitted a one-page abstract for judging. In February, they prepared and presented a poster that explained their research. A panel of judges went to each student and listened as the students explained their research in five minutes.The students worked hard at their research and then set aside time to complete all the necessary steps to enter the competition. The MPD recognizes the effort required to enter and as a result, provides monetary rewards to all participants. The first-place winner receives $1,000; the second, $500; the third, $250; and the fourth through seventh, $200. All remaining students receive $100. All of the students also receive a complimentary ticket to the MPD Luncheon. As in past years, there are separate levels of competition for undergraduates and graduates.Graduate winnersKaustubh Shrimali won first place for researching “The influence of starch in amine adsorption by quartz in the reverse flotation of iron ore.” Venkata Atluri received second for studying “The effect of polysaccharides on bubble attachment at talc surfaces.” Jennifer Galvin placed third for investigating “A novel approach to alkali pug bake for the extraction of rare earth elements from monazite concentrate.” In the fourth through seventh places were Amy Richins, Sumedh Gostu, Brett Carlson and Chris Vass.Undergraduate winnersNestor Santa earned first place for exploring “Copper recovery from waste printed circuit boards.” Cassidy O’Connell received second place for conducting “Performance analysis of CMC in high talc copper sulfide flotation systems.” Catalina Vanegas won third place for examining “Cyanidation tests and pretreatments to recover gold from a refractory ore in Colombia.” Kylie Boyce, Michael Archambo and Pritam Sinha were in the fourth through sixth places.Everyone benefits from attending the student poster competition. The students are able to display their work to future employers, and industry professionals can talk to up-and-coming engineers. Next year, there will be another competition for more posters and networking. Come and enjoy the event and the posters."

Jan 1, 2017

By E. Knell

COM Energy, Inc., a subsidiary of Occidental Petroleum Corporation, has constructed a 1.6 million hectoliter-per-year COM plant in Jacksonville, Florida. COM will be distributed to customers in the region as a substitute for fuel oil presently burned in boilers and kilns. As the market for COM grows, COM Energy, Inc. expects to build additional units both in this country and overseas. This paper addresses the overall status and technical aspects of the project, focusing on the facilities for COM production and utilization.

Jan 1, 1982

By Missy Isaman

"Mixed ground tunnels come in all kinds. In rock tunnels with possible faults and high pressure water, the challenges are many. With the advent of Crossover TBMs, contractors can minimize machine wear in such conditions while maximizing efficiency. The newest generation of Crossover is exemplified by two projects in Albania and Turkey. A 5.56 m Crossover TBM destined for Turkey’s Gerede Water Transmission will be assembled using Onsite First Time Assembly (OFTA) from within an existing tunnel. The unique machine will bore through 30 fault zones requiring the TBM to be sealable to up to 20 bar so pre-consolidation grouting can be done. If boring under pressure is required, the TBM will bore sequentially using the screw conveyor fore and aft gates. Skewing further towards hard rock, a unique 6.2 m diameter Double Shield TBM with Crossover features was designed for Albania’s Moglicë Headrace Tunnel. The machine features closure doors and a sealing system to contain inrushes of water until they can be grouted off. This paper will discuss the unique aspects of the Crossover designs, including their inception as based on past projects in difficult ground, and their utilization at the two current projects. INTRODUCTION Specialized tunnel boring machines have been made for years to tackle specific types of ground conditions. Traditional types of TBMs bore within a specific set of ground conditions. If a project is located in a competent granite face, then a Main Beam machine is a good solution. In soft ground, Earth Pressure Balance (EPB) machines are the method of choice. Years of experience and engineering advancements have made both types of machines fast and economical solutions for tunneling. Unfortunately not all ground conditions are a perfect swath of one material, and the need for a more diverse machine is apparent."

Jan 1, 2016

By S. J. Page

The personal dust monitor (PDM) is a combined tapered element oscillating microbalance (TEOM) respirable dust monitor and cap lamp, configured to have dimensions and weight similar to those of a lead-acid miner’s cap lamp battery. The Higgins-Dewell (HD) cyclone design operated at 2.2 L min-1 airflow has previously been reported to have low bias relative to the International Organization for Standardization (ISO) convention. Previous reports have described the PDM as meeting the NIOSH Accuracy Criterion. In order to avoid certain analysis anomalies encountered during these evaluations, a different method of establishing the PDM relative standard deviation was employed. Re-analysis of laboratory data for both the early prototype and precommercial PDMs indicates that the PDM still meets the NIOSH accuracy criterion, and that the precommercial PDMs are more accurate than previously reported.

Jan 1, 2011

By B. Pesic

This is an extension of the work on recovery of silver and manganese from Ag-Mn ores, and recovery of silver and gallium from flue dust from phosphate industry. Carbon adsorption was considered as the most adequate method for recovery of silver from thiourea leach solutions. For this reason it was decided to examine the characteristics of adsorption of silver on activated carbon. Coconut hard shell activated carbon was used for this study. Ag(TU)2C1 complex was dissolved into thiourea solution to give 2 gpl stock solution. Thy studied parameters were: loading isotherms at 25°C, 35°C, and 45°C, initial kinetics as a function of thiourea concentration, temperature, pH, N2, and O2. It was found that the loading capacity of carbon for silver and thiourea was 137-150 mg/g and 514 mg/g, respectively, at 25 °C.

Jan 1, 1986

By Anil K. Ray

Roof falls are one of the greatest hazards in underground coal mines worldwide. Due to stringent safety measures and extensive support system development, roof falls have been reduced significantly but they still persist in many underground coal mines. Some of the roof falls initiate with cutter roof or guttering. In the past, many factors have been identified as being responsible for the development of cutters and roof fall. These responsible factors can be broadly classified as stress related or non-stress related. In this paper the finer details of mining technique have been taken into consideration for better understanding of cutter roof and roof fall problems. Three dimensional finite difference modeling has been used to explain the mechanism of cutter development. Strain softening material behavior has been used to realistically simulate the cutter formation, and common cutting sequences as implemented in the field have been simulated. This was done with an objective to determine whether the cutting sequence has really any significant control over cutter formation or not. In addition to cutting sequences, the effect of cut length is also studied. The effect of step cutting and turning of crosscut into and away from major and minor horizontal stresses is also examined to see its influence on cutter development.

Jan 1, 2009

By Allan M. Harvey

Asbestos production in the United States is no match for the vast operations of Canada and the U.S.S.R. The majority of U.S. production is limited to the states of Vermont, California and Arizona, and the type of asbestos is limited to the variety of serpentine known as chrysotile. What little production of other varieties of asbestos such as tremolite and anthophyllite that has occurred over the past 100 years since asbestos became a useful commodity is of practically no significance. However, new developments in the field of environmental and occupational health hazards has startled the mining industry in this country and has already given a few particular companies reason to be concerned about the profitability and probability of their continued operation in the business of mineral processing. At the heart of these developments is the question and controversy over just what constitutes asbestos and what exactly is the definition of a fiber. To the mineralogist or, in fact, to practically anyone engaged in the process of mining and separating minerals there is little or no question about asbestos. It is not a distinct mineral but rather a commercial product serving specific applications for which a number of fibrous mineral types can qualify. To the hygienist pr health authority this definition is too general. They demand something they can detect, measure and control. To suit their purposes and simplify their task of detection, they have labelled the minerals chrysotile, crocidolite, amosite, tremolite, anthoph-yllite and actinolite as asbestos, and any particle of these minerals with an aspect ratio of 3:1 as an asbestos fiber. It does not

Jan 1, 1976

By E. Ashworth

A thermistor probe has been developed to measure in situ temperature profiles underground. A full description of the probe is given. Data collected from the probe has been used to compare the actual profiles with those predicted from a finite element analysis using laboratory measured thermal properties of the different rock types. This comparison indicates the applicability of laboratory measured parameters in modeling the real conditions. Factors such as applied pressure, moisture content and anisotropy on laboratory measurements is discussed.

Jan 1, 1983

By George R. Stephans

The Climax Mine is a panel caving mine which has had a long history of incidents of severe ground control problems. The nature of the ore deposit, which lends itself to the caving meth- of of production, a1 so makes the mine susceptible to large scale stress concentrations which are referred to as ?weight? problems. These problems have increased with increased production and also with expansion to deeper mine levels. During the past twenty years the mine has had to learn to cope with these problems in order to remain in operation. A number of practical guidelines and useful techniques have emerged from these efforts. The purpose of this paper is to share a few of these ideas. The Mine is located near Leadville, Colorado on the continental divide at an elevation of 3450 meters. The ore body is a large low grade deposit of disseminated molybdenum sulfide. It measures about 1200 to 1600 meters in diameter and it had an original depth of about 660 mters. The Mine has been in operation since 1918 and the massive nature of the ore body together with its blocky, highly fractured condition made it natural for the caving system to have been adopted for production at an early date. Open pit mining was started in 1973. The total plant has a capacity of more than 50 thousand tons per day, and more than 400 million tons of reserves at an average grade of 0.310 percent molybdenum disulfide remain to be produced.

Jan 1, 1982

By Carl R. Peterson

The Rapidex continuous drill and blast tunneling concept utilizes a unique spiral blasting pattern that permits efficient performance with relatively small single shots, while at the same time directing major blast fragments at right angles to the tunnel axis. The concept's self-shielding geometry permits the design of a lightly shielded machine that can stay at the tunnel face firing frequent small blasts to provide rapid, virtually continuous advance. This paper describes Phase III of the development program (supported under Bureau of Mines contract H0252047) in which the "front end" of the machine?drilling loading, and shooting components, together with the shield--was fabricated and field tested underground at the White Pine Copper mine, Michigan. One of the major accomplishments of the Phase III effort was to develop a fully remote controlled loading and initiation system in which explosive slurry is pushed, through a hose into the blasthole by a small water-driven piston carrying the blasting cap. The cap is ignited via an induction coil just prior to entry into the borehole, after which a delay permits complete -withdrawal and shielding of the loading hose. The ultimate objective of the present Bureau-sponsored program is to evaluate the feasibility of mechanizing hard rock mining operations, such as development to a point where drilling, loading, shooting, and mucking can proceed simultaneously and result in increased productivity.

Jan 1, 1977

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck

"Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27% of the respirable coal mine dust can be attributed to longwall shield movement. Developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine their ability of foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used; compressed air (CA) and blower air (BA). Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For CA foam in 3.3 m/s (3.3 m/s (650 fpm)) ventilation at 3 minutes after application, 98% of agent A was intact, while 95% of agent B was intact on the roof. At 30 minutes after application 94% of agent A was intact while only 20% of agent B remained. For BA in 3.3 m/s (3.3 m/s (650 fpm)) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 minutes after application 74-92% of foam agent A remained, while 3-50% of foam agent B remained. CA foam seems to remain intact for longer durations and is easier to apply than BA foam. However, more water drained from the foam when using CA foam which demonstrates that BA foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control. INTRODUCTION NIOSH personnel have visited many longwall operations at various geographical locations in the U.S., conducting benchmark surveys to characterize current operating practices and dust control measures in use. Sources of respirable dust generated from the longwall face have been identified as: intake (10%), stage loader (20%), shields (27%), and shearer (43%) [1]. Dust generated from the shearer, armored face conveyor, and the stage loader can mainly be controlled by water sprays and increases in ventilation air quantities, however, research has demonstrated limited effective controls for dusts generated by shield movements [2]. One possible approach to mitigating shield dust generation is to apply a layer of water or foam to the shield-roof interface. Once this interface is blanketed with foam or water, dust will be less likely to become airborne and contaminate the airways over the personnel walkways. Though water is an abundant and common dust control measure, roof applications have limited success because water is unable to remain in-place in adequate quantities for the necessary duration between application and shield advance. Past and current testing of foam for material properties has shown that it has longer applicability times, ranging from 10 to 60 minutes [3] and has shown better performance for dust control, ranging from 19-96% improved efficiency over water [4, 5, 6, 7, 8]. The majority of this foam dust control research has focused on dust control efficiency at the longwall shearer or continuous miner cutting drum."

Jan 1, 2017

By J. R. Maxwell

The development, commercial installation, and operating performance of large capacity Maxwell Flotation Cells. Volumes ranging from 300 cubic feet to 2,000 cubic feet per flotation mechanism.

Jan 1, 1971

By Colonel Oattis E. Parks

The quantity of coal recovered by diamond coring techniques is not sufficient in many instances to make meaningful coking and/or ash fouling tests. Quantities in excess of that obtained by conventional coring techniques, usually in amounts exceeding 500 pounds, has been designated bulk sampling. During the past three years, AMAX Coal Company has utilized five methods of bulk sampling. It was our desire to obtain a bulk sample that was diagnostic of the seam by the most expedient and economical method. From the beginning all of our efforts have been directed to methods which would extract the required coal from slim boreholes which provide quick and inexpensive access to the coal seam, regardless of depth, terrain and accessability. In our efforts and investigation several large diameter cores have been taken from thick coal seams at relatively shallow depths in easily drilled rocks. On the other hand, for deeper thin seams multiple large diameter coring is more expensive and time consuming. It is somewhat less expensive when multiple cores are taken from a single slim borehole utilizing deflection coring, although considerable skill is necessary.

Jan 1, 1973

By Ken Pill, Jennifer Nyman, Liz Moran, Keaton Belli, Chelsea Bokman

The Moab Uranium Mill Tailings Remedial Action (UMTRA) Project Site (Site) is a former uranium-ore processing facility near Moab, Utah, where production ended in 1984. The United States Department of Energy Office of Environmental Management (DOE-EM) is responsible for remediating the site to meet 40 Code of Federal Regulations (CFR) 192 standards promulgated by the United States Environmental Protection Agency under the authority of the Nuclear Regulatory Commission (NRC). Tailings from the former mill were stored in an unlined impoundment (tailings pile), totaling 16 million tons of waste material. Surface cleanup has been ongoing since 2009 and consists of removal and transport of tailings via rail to an off-site disposal facility in Crescent Junction, Utah, with an estimated completion date around 2029. Gravity-driven migration of tailings fluids and recharge through the tailings pile and former on-site ore storage areas in the northeastern part of the site led to contamination of site soil and groundwater. The primary contaminant of concern is ammonia, which was present in fluids used in the milling process (DOE 2003). Uranium is a contaminant of potential concern. An interim groundwater remedy is currently in place that utilizes a system of extraction and injection wells to limit discharge of contaminated groundwater into the nearby Colorado River. Exceedance of surface water standards for ammonia are a principal concern due to potential endangered species fish habitat areas along the Colorado River adjacent to the Site. When necessary, surface water diversion is used to lower surface water ammonia concentrations when suitable habitats develop for endangered young-of-year fish. Once surface cleanup concludes and the tailings pile is removed, a formal groundwater remedy must be selected and documented in a Groundwater Compliance Action Plan (GCAP). Under Title 1 of the Uranium Mill Tailings Radiation Control Act, natural flushing (i.e., monitored natural attenuation), may be selected as the groundwater remedy if it can be demonstrated that the remedy will achieve groundwater standards within 100 years. The 40 CFR 192 groundwater standard for uranium is 44 micrograms per liter (μg/L), and the target groundwater concentration of ammonia based on adverse effects on local fish species is 3 milligrams per liter (mg/L). A collaboration with Geosyntec Consultants, Inc. (Geosyntec), the Moab UMTRA Project team, the DOE Office of Legacy Management, the DOE-EM, and the Network of National Laboratories for Environmental Management and Stewardship was held in 2022 with the goal to generate actionable recommendations to develop a GCAP for the Site. The primary recommendation was development of a groundwater fate and transport model to predict the remedial timeframe under various groundwater remedies. This paper presents the results of soil and groundwater sampling, geochemical modelling, and laboratory column and batch reactor testing that will be used to parameterize a numerical model for estimating the remedial timeframe under various scenarios, including natural flushing.

Feb 1, 2025

By Roberto Carranza

The planning of experiments and the importance of statistical interpretation of the results have been recognized for years by scientists and engineers. The Factorial Design of experiments is among the various methods used for this purpose and is being widely applied in all branches of research and production. The basic principles of this tool have been described in detail (1, 2, 3, 4) and several examples of its application in various fields have been published (5). In recent years the mineral industry has also used Factorial Design to improve the efficiency of research, testwork and plant operation (6, 7, 8, 9). This method permits for a qualitative determination of the influence of the variables studied in a process and also a qualitative measure of the interaction of the variables. By graphic means or derivative methods, one may also establish the optimum conditions of the process (ibid 7, 8, 9). It is desirable, however, to develop mathematical methods to evaluate quantitatively these effects and restrict the optimization to the practical limitations of the variables. It is also convenient to adopt a notation system to generalize the Factorial Design.

Jan 1, 1971

By Walter H. Schwedes

Ore grinding mills are really just slowly rotating barrels, but barrels that are growing in size so fast that the application of electric drives for them is rapidly approaching a technology like that for wind tunnels or pumped storage drives. This application is particularly worthy of care because some 40% of the 75 megawatts of power used by a large copper ore concentrator, or some 60% of the 200 megawatts supplied to a large iron ore concentrator, are for grinding. These ore plants are located where the ore is, not where a utility happens to be. So, the challenge is not only to choose a drive and .power transmission for reasonable cost, high performance, reliability and minimum maintenance, but to afford the interface between mill drive and power distribution and source systems to minimize the whole ore plant's monthly power bill, or costs of self generation. Conclusions can be reached in optimizing a drive selection only for each particular ore plant's set of parameters, but by identifying the criteria for selection and then weighting each type of drive per criteria, yardsticks for final choice become apparent. This is the purpose of this paper. Grinding action takes place inside the barrel, where the ore charge is ground with the aid of balls, or mill length rods, or large chunks of ore as in autogenous grinding.

Jan 1, 1972

By John W. Straton

Following the completion of the paper presented in February, 1972, data were received from many other mines and some original respondents submitted more complete questionnaires. The computer program was changed to permit the results to reflect more clearly all the data reported by the mines. The original paper was revised to reflect the new information. There were significant changes in some numerical values, particularly where the size of the sample changed appreciably. Some limited samples considered originally in arriving at conclusions were not relied on in this revision. The revised tables and text are of the same design and format as the original paper.

Jan 1, 1972

By Brian W. Mackenzie

The mine development decision is made on completion of exploration to determine whether or not a mineral deposit should be developed to production and, if so, how. This involves the selection of an optimum mine development alternative from a number of technically feasible alternatives and the comparison of this optimum with those of other available investment opportunities. If the optimum is sufficiently attractive, the deposit is developed to production. The selection process is carried out within a framework of corporate objectives and resources. The mine development decision is based on the balancing of two parameters - - rate of production as reflected in plant capacity and cut-off grade. On the basis of available information and experience, detailed revenue and cost 'estimates are made for each feasible combination of plant capacity and cut-off grade. What economic evaluation techniques should be applied to these estimates to reduce each alternative to economic indicators that will enable meaningful comparisons and an informed investment decision? This is the essence of the paper. The determination of optimum plant capacity and cut-off grade has been the subject of intensive research efforts by economists and mining engineers (1-7). Their studies are based on marginal analysis and assume that, at the time of decision, certainty conditions prevail with respect to ore reserves, mining costs and mineral markets. The optimum mine development alternative is defined as that which maximizes profitability.

Jan 1, 1969

By M. Shriwas, F. Calizaya

"Recirculation is prohibited in many coal mining countries because of the fear that the re-use of return air would allow the build-up of air contaminants at the workings. The incorrect design and location of a booster fan in any ventilation network can create unsafe condition due to recirculation. The current approach to investigating recirculation using simulation software requires manual effort which becomes tedious in a complex and a large network. An algorithm-based C++ program was designed to detect the recirculation in a booster fan ventilation networks. This program needed an input file prepared from output file generated by any ventilation simulator. This program created an output file for recirculation. This program demonstrated the strong capability to detect the recirculation in a sample network and a coal mine ventilation network. The outcomes of this program were documented in this paper. INTRODUCTION The proper design and location of booster fans eliminate the safety hazards associated with high main fan pressure. Conversely, the incorrect design of booster fans in any ventilation network can create unsafe conditions due to uncontrolled recirculation. The proper utilization of a booster fan derives benefits to reduce the main fan pressure, leakage, and consequently ventilation cost especially with high resistance network due to deep and extensive working area in a mine. However installation of booster fan may create uncontrolled recirculation, if it is not sized and located properly with respect to main fan. Recirculation is prohibited in many coal mining countries because of the fear that the reuse of return air would allow the build-up of air contaminants at the workings. Therefore, it is imperative to check the recirculation while designing and operating booster fan for a ventilation network. This paper deals with an algorithm based C++ program to detect the recirculation in a booster fan ventilation networks. This program was implemented to detect the recirculation in a sample network and a coal mine network. STATEMENT OF PROBLEM The currently available ventilation simulation programs do not give much information about recirculation for the generated solution (fan pressures). The current approach to investigating recirculation using simulation software requires manual effort, i.e., traversing from node to node in the output network by the simulator while keeping tracks of all the nodes that form recirculation paths. This is an easy task in a simple ventilation network, but it becomes tedious and sometimes very confusing in a complex and large network. Moreover, the presence of multiple recirculation paths makes the manual effort more complex and difficult, especially in separating multiple loops that are connected together. Thus, there is a need for a more efficient program that will detect and quantify the recirculation efficiently, for the generated fan pressures. A program is developed to detect the recirculation(s) in a network."

Jan 1, 2015