Search Documents

By Virginia T. McLemore, Devlon R. Shaver

Clinkers are the result of a seam of coal catching fire and burning the surrounding rocks. The fires caused the surrounding rocks to be baked at high temperatures, removing organic material and partially forming glass. These rocks become hard, orange, and brick like, forming clinker. The purpose of the study is to determine their potential to contain economic levels of critical minerals, including Rare Earth Elements. Some clinkers contain over 200 ppm total REE.

Feb 1, 2024

By QUANWEN PU, Yonggang Wei, Bo Li

With the advancement of industrial science and technology, more and more catalysts are used. The spent catalysts produced are solid waste products, which cause environmental pollution if they are not treated. At the same time, the spent catalysts contain some precious metals such as platinum in concentrations that are often higher than in their ore resources. Therefore, the recovery of valuable metals in spent catalysts is a hot research topic at present. However, due to the complex structure of the spent catalysts, dealing with them is a lengthy process. The first step of recovery, enrichment of the spent catalyst, becomes particularly important. In this paper, a pressure solution method is investigated for this purpose, in which the alumina carrier is dissolved and platinum is enriched in the leaching residue.

By Thomas H. Dubaniewicz

(XP) enclosures to enclose electrical ignition sources to prevent propagation of an internal methane-air explosion to a surrounding explosive atmosphere. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a lithium-ion battery thermal runaway test within a modified MSHA-approved XP enclosure to assess thermal runaway containment. Thermal runaway produced jet flames emanating from the cover joint at several locations and distorted the cover joint and bottom plate of the enclosure beyond allowable limits. The test demonstrates that XP enclosures may not provide adequate explosion protection against lithium-ion battery thermal runaway. This paper suggests some approaches to mitigate the hazard.

Feb 1, 2024

By Yuexin Han

The characteristics of comminuted hematite products using a high pressure grinding roller (HPGR) and conventional jaw crusher (JC) were comparatively studied by screening, optical microscope, scanning electron microscope (SEM) and Brunauer, Emmett and Teller (BET) techniques. Major properties investigated included product size distribution, particle cracks, specific surface areas and pore volumes. Results showed that in a closed-circuit operation with a screen opening of 3.2 mm, the HPGR and JC gave a similar P80, but the HPGR achieved a more uniform size distribution, more fines and a higher crushing efficiency. Three modes of cracks were identified, namely transgranular cracks, innergranular microcracks and intergranular microcracks. Transgranular cracks originated from shearing breakage. Innergranular and intergranular microcracks were generated by HPGR via the two main nonrandom breakage forms, preferential breakage and interfacial breakage, depending on their respective ability to endure stresses when mineral phases (particles) were loaded against each other. The BET values for the same-size fractions showed that HPGR products gave higher specific surface areas and more pore volumes than JC products. This indicates that HPGR-crushed products are easier to grind because of their high porosity and extra cracks.

May 1, 2012

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters when implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of karst voids, which are frequent phenomena in carbonate rock formations. This research continues a previous study aimed at studying the effect of karst voids on the strength of a particular limestone pillar. Using calculated pillar strength and estimated redistributed stresses, it was assessed that the pillar can counter more stress than currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using distinct element method (DEM) modeling to determine a better design.

Jun 1, 2023

By S. Miller, A. Krasner, M. Sizintsev, S. Schafrik, H. -P. Chiu, J. Sottile, A. Rajvanshi, Z. Agioutantis

In recent years, a great deal of effort has been put into automating mining equipment with the goal of improving worker health and safety and increasing mine productivity. Significant progress has been made in automating mining equipment such as load-haul-dumps and drills in underground environments where global positioning systems are unavailable. This paper addresses automating the task of positioning the shuttle-car (SC) under the continuous-miner (CM) coaldischarge conveyor during cutting and loading operations. A stereo depth camera is mounted on the SC. Machine learning based algorithms are applied on the camera’s output to identify the CM discharge conveyor and segment the scene into various regions such as roof, ribs, and personnel. This information is used to plan the shuttle car path to the CM discharge conveyor. The approach currently uses a 1/6th scale continuous miner and shuttle car in an appropriately scaled mock mine

Mar 2, 2022

By Andre Vien, SANDRO DAVID DI, Frank Laroche

In 1994, Claude Bazin presented a novel method for linking size data from milling models to the feed input of flotation models. It was achieved with the simple addition of a metal/mineral distribution–size distribution relationship. This allows grade and recovery predictions from a varying mine plan through product size distribution predictions. 

By T. Y. Yan

The various ion exchange reactions occurring during the restoration of formations contaminated with ammonia during in situ uranium leaching are reviewed. Data are presented on the restoration of a previously leached laboratory packed column using line saturated brine. Although this restoration fluid selectively and effectively removed the ammonia, 24.5 pore volumes are required to reduce the ammonia concentration from 500 to 3 ppm. The presence of NaCl in the restoration fluid is beneficial in + improving the selectivity of the system for NH removal and reducing ca++ ion consumption.

Jan 1, 1982

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

The paper addresses heat stress in underground coal mines, which poses significant threats to miners’ health, safety, and productivity. It involves a comprehensive ventilation survey in three deep and mechanized underground coal mines in India. Using VentSim software, 3D simulation models were developed to predict heat stress conditions and explore the application of auxiliary ventilation and spot coolers to reduce heat stress.

Oct 1, 2023

By Ma Lianren, Wang Duolun, Chenzhe Li, Hongyan Xie, Fenglan Luo, Huixin Jin

In this study, the oxidation of low-grade pyrolusite to potassium manganate in alkaline solutions under O2 pressure has been investigated. The effects of different conditions on the high-grade and low-grade pyrolusite leaching process were investigated based on thermodynamic calculation, as well as the reaction mechanisms and kinetics of the low-grade pyrolusite during the leaching process. The results showed that the manganese conversion rates of the two types of pyrolusite were almost the same, and reaching 99% for high-grade pyrolusite and 96% for low-grade pyrolusite under optimal conditions. The optimum condition for low-grade pyrolusite sample JM-2 was achieved as 0.5 MPa of the oxygen partial pressure, 55% of KOH, 14 of the initial alkali-manganese ratio, and ≤ 48 μm of the mineral granularity at 260 °C within 150 min of leaching time and 500 rpm. In alkaline leaching of low-grade pyrolusite, Mn(IV) was oxidized into Mn(VI). The particles changed from large particles to flakes and finally formed crystals. Finally, the shrinking core model was used to fully describe the leaching kinetics of the manganese. It was demonstrated that the leaching of manganese was controlled by the chemical surface reactions and the activation energy which equals 115.9121 kJ/mol.

Dec 3, 2022

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

By W. Z. Choi

A combined size reduction- liberation model of grinding has been developed to predict the product size distribution for both free and locked particles. The model is an extension of the population balance model for size reduction. Locked (or composite) particles have been subdivided into discrete classes of different compositions to obtain more detailed information. The model has been tested on a sphalerite ore from Tennessee. Liberation data have been obtained using an areal scanning technique on microscope images of polished particle mounts.

Jan 1, 1985

By David B. Brooks

I gratefully acknowledge the help of a number of American and Canadian geologists, in both federal surveys and in private firms, who took the time to discuss this problem with me. Hans Landsberg and Bruce Netschert also followed the study with interest and encouragement. In their 1961 monograph, THE FUTURE SUPPLY OF THE MAJOR METALS, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.1/ Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vest quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.? 2/ This situation, which they called "the lead-zinc anomaly" has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative.

Jan 1, 1967

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) is used in the mining industry for early fire detection. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) have developed a direct method to calculate the fire heat release rate (HRR) when a mine fire is close to the AMS sensors, but this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire HRR using AMS sensor data at any location downstream of the fire. The method was validated using a full-scale diesel fire test conducted in the Safety Research Coal Mine at NIOSH’s Pittsburgh Mining Research Division.

By S. L. Barua

An industrial engineering and computer simulation study was conducted on reclamation operations to evaluate the possibility of integrating mining and reclamation operations, and to evaluate the factors which influence the production potential of scrapers. The study was done in a southern Illinois strip coal mine producing approximately 2.27 M metric tons (2.5 million short tons) of clean coal annually. The main outcomes of this study are (a) it is possible to reduce reclamation cost about 20-25 percent by integrating reclamation and mining operations, (b) haul distance has the most significant effect on scraper production, (c) push-pull is the best mode of operation for wheel scrapers for topsoil/subsoil removal, and (d) historical data obtained from the mine for one year show that average dozer productivity in rock grading is about 60 percent lower than the expected production; similar data for scraper is about 25 percent less.

Jan 1, 1981

By Roy H. Paddon

This paper describes the 6, 000 tpd, three stage haulage system at the Ozark Lead Company's mine in southeastern Missouri. It details the methods and problems pertinent to the loading, hauling, sorting, crushing, storing and hoisting of waste rock and ores obtained from underground development headings and production areas. The Ozark Lead Company is a wholly owned subsidiary of the Kennecott Copper Corporation. Its mine is located nine miles south of Bunker in Reynolds County at the south end of the "New Lead Belt" mining district. Development started in May, 1964, by drilling a seven foot diameter (six foot cased), 1, 250 foot development-ventilation shaft. Drifting began in August, 1965, to obtain a bulk ore sample, to test ore continuity, and to drive two mine levels while the pre-grouted production shaft was being sunk. Over 7, 900 feet of 12 by 24 foot drifting was done from this small shaft. In March, 1966, a 20 foot diameter, three compartment, concrete lined production shaft was collared. It intersected existing development headings at a depth of 1, 195 feet in April, 1967, and was completed along with a concentrator and other facilities in June, 1968. Mine production began that month, with 5, 000 tpd reached in 1970.\

Jan 1, 1971

By Brendan Donnelly, Jung-Hoon Sul, Lasitha Piyathilaka, Sanghyun Jeong, Benjamin Probyn

The chains of armored face conveyor (AFCs) are constantly in contact with water and wet coal, which results in a significant proportion of unplanned downtime experienced on longwall equipment due to corrosion. While reverse osmosis (RO) is one of the most prevalent water treatment methods for reducing salinity and dissolved solids in coal mining, its impact on the corrosion of the AFC chains has not been well studied. This work studies the direct effects of RO water on the corrosion of AFC chains. Immersion tests followed by surface micromorphology analysis and corrosion indices indicate that the RO water increased the corrosion rate of the AFC chains due to the reduced tendency of preventive films on the chains.

May 1, 2024

By Maurício Covcevich Bagatini, Maycon Athayde

Water consumption reduction in pellet feed operation is of paramount importance. Compared with traditional ball mills, high-pressure grinding rolls (HPGR) play an important role in Blaine surface area (BSA) generation to improve agglomeration properties, although stability is still a challenge. Grindability improvement of existing operation has a direct impact on the performance of the filtering and pelletizing operation. The results of this study, as a pregrinding operation, can be applied not only in new operations but also in existing ones, helping the operator control process variation in a more effective way while ore hardness increases. 

By Shawn P. Coughlin, Michael A. Schimmenti, Juan Leonardo Tello del Pino

"The Sistema de Potabilización Área Norte project (Northern Area Purification System) was a major expansion of the potable water system in Buenos Aires Province, Argentina. The aim of the project was to transport and purify raw water from the Paraná River to provide potable water for five communities in the northern part of the province, benefitting up to two million people. The project was constructed by a joint venture (JV) of four South American contractors and consisted of the following key components:• Treatment plant: A 16-ha (39-acre) area was cleared for the construction of a treatment plant to purify 900,000 m3/day (1.2 million cu ft/d) of raw water from the Paraná River and distribute it to the surrounding communities.• Bored tunnel: Nearly 15 km (9 miles) of 3.6 m (12 ft) inner diameter tunnel, ranging from 18 to 22 m (59 ft to 72 ft) below grade, was bored with two earth pressure balance (EPB) tunnel boring machines (TBM) to draw the raw water from the river. The TBMs started from a central launch shaft and proceeded in opposite directions. Cristina advanced northbound to the Paraná River Intake System, and Liliana advanced southbound to the new treatment plant.• Access and ventilation shafts: Five access shafts and eight ventilation shafts were installed along the length of the tunnel. The access shafts were designed to provide entry points for inspection and maintenance of the final tunnel. The five shafts consisted of one central launch shaft in the middle of the tunnel alignment, one retrieval shaft at each end of the tunnel (intake and treatment plant, respectively) and two intermediate shafts. The intermediate shafts were installed before the TBM passed, with a final liner to be installedafterward."

Sep 1, 2016

By John S. Cummings

Although there are many geologic situations which might be discussed at a session such as this, as I considered the problem, it became apparent to me that I should discuss a situation which has been of concern to me, and should be of concern to the geologic community. As a result, the questions which I will pose, and the criticisms, have not been arrived at quickly or easily, but have accumulated through time, to the point where I feel discussion is necessary. Very briefly let me say that my criticism of geologic mapping, of conclusions reached, and objectives or lack of such, results from my association with many areas where such studies have been completed, and resultingly my inability to comprehend the system of evidence or logic which supports extensive age-formational designations. The heart of the problem is that many conclusions resulting in geologic designations are based on weak or non-existent evidence, and such should be catagorized as hypotheses. Although the geologic community as a group does not approve or disapprove of such designations, it is evident that many or most of such designations attain a "status", and arc accepted as more or less valid statements. As will be shown, the amount of specific lithologic data provided in some quadrangle mapping projects is exceedingly slim. However, of concern herein is that the type of information presented at any stage is sufficient to warrant conclusions drawn. To see the magnitude of the problem, it is probably necessary to review some basic fundamentals upon which our geologic systems are established. The United States Geological Survey has defined a "formation" as the broad unit of geologic mapping consisting of a large and persistent stratum of one kind of rock. Obviously such a designation allows that a formation could be considered "time variant" in a horizontal as well as in a vertical context. However, other definitions enable a formation to mean units

Jan 1, 1972