Search Documents

By Bernd Hagenah, Katie Theis, Cristina Lauzon, Petr Pospisil

Lidding over or tunneling existing transportation infrastructure is currently under review in several U.S. cities. The main reasons for this are the use of the created space for urban development, the reduction of noise and exhaust fumes for the residents, and, thus, a significant increase in the quality of life. The main aspects to be considered during the planning process are (1) total investment and operational costs, (2) impact of construction works on current traffic, (3) safety and fire protection, and (4) socio-environmental issues. The paper presents some basic planning principles, and experiences of recent urban highway coverages are shared.

Jun 23, 2024

By H. N. Dougherty

"The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) ventilation gallery was used to study methane-air flows around a continuous miner mockup with water sprays and a scrubber fan. Methane gas was released from pipes located at the face to simulate face gas emissions. Methane concentrations and air velocities were measured while varying parameters such as airflow quantity, entry width (sump or slab cut), and face ventilation configuration (blowing or exhausting curtain). Test data showed a similar pattern of methane concentrations at both low and high airflow quantities, but a difference in the distribution of methane concentrations between narrow and wide entry widths. Most tests showed that blowing face ventilation was more efficient in diluting methane than exhausting ventilation, similar to observations made in previous empty gallery studies. The patterns of airflow and methane concentrations observed in this testing can further improve the understanding of airflow in and around the CM and face, promoting effective use of face ventilation to improve the health and safety of miners. INTRODUCTION Attaining an accurate understanding of airflow distribution at the continuous miner face is instrumental in maintaining a safe mining environment. US mining regulations require that sufficient airflow must be directed to the deepest penetration of the face and render harmless contaminant gases, as verified by the Mine Safety and Health Administration (MSHA). Currently, continuous miner face air readings can be taken in the last open crosscut and at the inby end of the curtain mouth. By measuring adequate airflow in a pre-determined area it is accepted that a sufficient quantity of that air exists to sweep the face of harmful dust and gasses. Unfortunately, due to the location inaccessibility, precise face velocity readings cannot be measured in situ. Face velocities may be estimated through computer-simulated programs based on laboratory models. Improving upon previous empty gallery testing and to more effectively determine representative face methane readings, a mockup of a continuous miner with water sprays and a scrubber fan was used in the current study to further refine face airflow conditions that would be closer to actual mining conditions."

Jan 1, 2016

By Kallam V. K. Reddy, VADAPALLI SANJANA, Veerendra Singh, Gajanan Kapure

This work describes a leaching process for the conversion of high-magnesium peridotite rock, which is a chromite ore overburden, into two valuable products: magnesium salts and micro silica. Under normal leaching conditions, residue remaining after leaching is of a gelatinous nature and thus hinders the filtration process. To address this issue, oxidative leaching with the addition of H2O2 was employed, and it significantly improved the filtration kinetics. Four different approaches for H2O2 addition were tried, and they all proved effective in controlling gelation. The optimum oxidative leaching condition was 70 °C, 2 h time, 2 M H2SO4, 0.5MH2O2 and 400 RPM; under these conditions, 92% magnesium leaching efficiency was achieved. After leaching, the leach liquor obtained was purified and dried into Mg(OH)2 and MgSO4 salts. The leach residue contained mainly silica particles, with size in the 10–30 μm range. This material thus represents an attractive candidate for the production of highperformance concrete for the construction industry. The oxidative leaching process described here enabled the complete conversion of peridotite into valuable products, magnesium salts and micro silica.

May 5, 2020

By Robert Hochscheid

A patent issued to J.N.J. Leeman (1957) described the change in performance that takes place when a cyclone is installed in the horizontal position rather than the vertical position. Although this patent was directed more toward improvements that could be realized in the heavy medium cleaning of coal, it contained specific references to reducing the quantity of fine solids that would report in the underflow, and an example for fine sand classification is also included. The three cyclone installations for which data is given in this paper demonstrate that horizontal mounting of large cyclones can improve classification efficiency, eliminate some operational difficulties, and reduce cyclone maintenance requirements in closed circuit grinding installations. Cyclone Experience at Serrana S.A. Each of four grinding circuits at the Serrana S.A. de Mineracao Apatite flotation plant in Brazil have a 2.7 X 4.6 meter (9 X 15 foot) rod mill and each originally operated in closed circuit with two vertically mounted Model D20B (500m nominal diameter) Krebs Cyclones. New feed size is 25mm. The Apatite is liberated at a relatively coarse 35 to 28 mesh grind, but the 500mm cyclones had to be fed at 66 pct. solids in order to obtain an overflow analyzing 12 pct. coarser than 42 mesh. Because dilution water in the cyclone feed had to be limited, classification was inefficient, and there were other significant circuit difficulties as summarized in a recent article by C. A. Busnardo (1984):

Jan 1, 1985

By A. Taghavi, I. Hassan, A. Solecki

"The Eglinton Crosstown Light Rail (LRT) Project is part of an $8.4 billion investment to expand transit in the Toronto, Canada area and is the largest transit project initiated in Province’s history. Settlement control and impact to over 1400 adjacent structures due to tunnelling was identified early as a critical project risk. The ground conditions along the 10km tunnel alignment consist of water bearing soft ground deposits (clays, sands, silts) which required careful analysis and control during design and construction. This paper will describe the process used to analyze settlements along the numerous of adjacent structures and evaluate achieved settlement results to those used during design. The paper will demonstrate that with the appropriate design specifications, selection of modernized EPB machines, and contractor performance, settlement can be maintained well below typical industry (volume loss) standards, expanding the application and suitability of soft ground tunnelling in sensitive settlement areas. INTRODUCTION The Eglinton Crosstown Light Rail Transit (LRT) Project is part of an $8.4 billion (2010$ CND) investment from the Ontario provincial government to expand transit in the Toronto, Canada area. The project is being developed by Metrolinx, an agency of the Government of Ontario to provide 19 kilometers of dedicated LRT service connecting the City of Toronto from the west to east along Eglinton Avenue. Upon completion in the year 2020, the Crosstown will be the first LRT constructed in Toronto. It will link regional and local transit, cut travel time along the route by half and provide over a thousand jobs during construction."

Jan 1, 2016

By Robert B. Fulton

The objective of this chapter is to discuss the interrelationship between industrial minerals and chemical manufacturing. It is intended to supplement rather than duplicate the commodity chapters. Particular emphasis is given to the pertinent chemical element and to market factors. Condensing this broad subject into a few pages of this handbook permits treating only the most important elements derived from industrial minerals. Hydrocarbons, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potassium, and nitrogen for fertilizers, and titanium dioxide for pigments. The remaining six elements of major importance are: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. [Table 1] affords an overview of the main industrial minerals, the chemical products derived from them, and end uses of the products. Salt brines have particular importance as raw material sources for the chemical industry. Table 2 is a chart of the chemical compounds derived from four types of brines: (1) Owens Lake-type brines, which are sources of boron and sodium compounds; (2) Midland-type brines, from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake-type brines, yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak- type brines, produced mainly for lithium. MARKET ATTRIBUTES Some of the important market traits common to industrial minerals used by the chemical industry are: 1. They are international commodities, such as fluorspar and sulfur, which largely move to foreign consumers. 2. Grade, and freedom from deleterious elements are important factors affecting their usability in chemical processes. An example is salt (NaCl) used in electrolysis where ultrapure evaporated salt is required to meet rigid specifications. 3. Purified products take on the characteristics of specialty items and command a distinctly higher price than the basic commodity from which they are derived. 4. In practically all cases, chemical users require some sort of cleaning or beneficiation of the naturally-occurring mineral to bring it to specification, and individual specifications may vary from user to user for essentially the same use. 5. In some instances it is necessary to strike a balance between what the vendor can supply and what the buyer requires, with the result that specifications have to be eased to afford the needed materials in marginal cases. 6. Because they tend to be bulk commodities, low cost for handling and transportation are important and such costs may limit the area from which a chemical user can draw his supply. 7. Shipments are usually in bulk and frequently in multiple-car, full-trainload or full-shipload lots to reduce transport costs, which in turn may require large terminal investment facilities. 8. Purchases are generally by contract of one year or longer term, with spot buying playing only a minor role. 9. Contract prices are usually fixed in short term commitments, but may vary according to assay, with premiums and penalties for content above or below the norm; however, general practice is for specifications to be fixed in the contract with minimums being set for the desired material and maximums for undesired elements. In longer term contracts, prices are often escalated on labor, fuel, and other vendor processing costs. 10. Suppliers of individual commodities to the chemical industry tend to be limited in number and are generally medium- to large-size producers that supply a few major consumers. 11. The bulk of the mineral volume is for basic chemical uses, sulfur suppliers to sulfuric acid producers and fluorspar for hydrofluoric acid producers being typical examples. These basic chemical products then are used for the production of other products. 12. Shortage of a supply of adequate quality leads consumers to seek substitutes. In the case of fluorspar, much work is being done on recovery of fluorine from phosphate rock. Success in the form of fluorosilicic acid and/or hydrofluoric acid production could, in time, affect the hydrofluoric acid chemical industry. 13. Markets tend to be characterized by cycles of shortage followed by oversupply, with attendant wide price fluctuations. 14. Baniers to trade can have an adverse effect on the necessary movement of industrial minerals used by the chemical industry in international trade. Antidumping laws, quotas, and tariffs can disrupt or dislocate normal markets. 15. Chemical industry consumers may back-integrate for security of supply or for favorable economics, sometimes by joint ownership and often with experienced mining partners.

Jan 1, 1994

By Tyler Acorn, Brandon Wilson, Jeff Boisvert

Project-scale decisions in surface mining operations rely on the optimization and subsequent evaluation of pit limits. This process ignores the ability for mine plans to adapt as more information is gathered. Stochastic methods, which consider uncertainty in the pit optimization, generally act to refine the boundaries of the pit on a fine scale. This paper extends uncertainty-based methods to consider unique scenarios through a clustering of the realizations that are being optimized. This results in the generation of multiple sets of similar realizations. A separate pit is optimized on each set of realizations, resulting in the production of a series of planning scenarios. This accounts for the adaptability of mine planning as more information is gained. A decision-making framework is then applied to the resulting scenario plans to select the optimal choice. The improvements stem from the joint uncertainty considered when realizations are grouped that is not considered when the probability of a block being in any optimized pit is considered. Mining operations today can benefit from considering additional planning options as identified and evaluated in this workflow.

By J. A. Haggman

In a country richly endowed in mineral wealth, Climax Arimco Mining Corporation's (CAMC) Dinkidi porphyry Au?Cu deposit in Nueva Vizcaya province, Philippines, represents the most significant mineral discovery in the country in recent times. The deposit is located within a belt of young intrusive and volcanic rocks in the Sierra Madre mountain chain of north Luzon a region previously unassociated with porphyry-style mineralization. Since 1989, drilling of the Dinkidi deposit has outlined a resource of 124 million tonnes of 1.0 g/t gold and 0.41 % copper. Regional exploration throughout CAMC's 37,000 hectare FTAA has identified a further sixteen potential porphyry-related deposits. A new mining law was passed in March 1995 but prior to that CAMC had the first Financial and Technical Assistance Agreement (FTAA) granted by the Philippine government allowing 100% foreign ownership of mining projects.

Jan 1, 1997

By S. S. Peng

In this paper, the precise definitions for a number of commonly used subsidence parameters are given. The subsidence parameters have been determined using an integrated approach for 110 subsidence cases collected in the major US coal fields. Attempts have been made to establish empirical formulae for the parameters. The results of this study indicate that some traditionally-held concepts should be changed.

Jan 1, 1995

By Jordi Vives-Costa, J. J. de Felipe, Lluís Sanmiquel, Maria Niubó

The article evaluates the convective heat transfer coefficient of ventilation air in a potash mine. The energy balance is obtained through thermal characterization of the ventilation air and rock, allowing for the calculation of heat transfer parameters. Different models for calculating the convective heat transfer coefficient are analyzed. The results indicate that the Pethukov–Kirilov, Gnielinski, and modified Dittus–Boelter models are optimal for this mine. The study also indirectly examines the conductivity of the adjacent rock, suggesting saturation throughout the studied section and the presence of liquid water upwelling in a specific section.

Apr 7, 2022

By John Hanna

Recently. researchers at The University of Alabama have developed a two-step method for the treatment of phosphorus sludge that includes bulk removal of phosphorus by physical separation techniques followed by remediation of the residual P4 in the sludge using a novel wet air oxidation technique known as "HSAD", Tests made on samples of the electric furnace phosphorus sludge have demonstrated that essentially complete and fast removal of the P4 in the sludge can be achieved by the HSAD wet oxidation treatment, Further studies were made to determine the applicability of the two-step process on sludges of various origins. P4 contents different pre-treatment and storage conditions, The present work discusses the mechanisms and factors controlling the HSAD wet air oxidation remediation approach.

Jan 1, 1992

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

The initiation of a panel cave is an extremely important and infrequent event in the life of a large underground caving operation. A new cave was initiated at the Henderson Mine in 1991, 15 years after its first cave had been developed in 1976. The original cave was started after a half billion dollars had been invested in the development of the mine, mill and 23 km haulage system. Many things had changed since 1976, the most significant of these being much lower realizations for molybdenum. In 1976 the high demand for molybdenum and uncertainty of caving characteristics, formed the basis for a very conservative cave initiation sequence with miles of boundary weakening and inspection drifting. In 1991 the highly competitive molybdenum market in conjunction with 15 years of caving experience made for a very different mining climate.

Jan 1, 1994

By R. T. Torrie, J. R. Mernagh, D. B. Chambers

l, INTRODUCTION Uranium mine and mill workers are exposed to external gamma and beta radiation fields from radioactive ore. In the past the average uranium content of ores mined in the United States and Canada ranged from about 0.1% to 1.0% U308 with pockets of much higher grade ore. Holiday (1973) reported that radiation surveys in the U.S. uranium mines found mean gamma "radiation rates ranged from 0.20 to 0.70 mrem/h. Such radiation rates cause relatively insignificant exposures." Others also concluded that the external gamma radiation fields associated with uranium mining did not result in significant worker exposures (Federal Radiation Council, 1967; Simpson, S.D. [et al], 1959) Gamma exposure levels in most modern-day Canadian uranium mines are reported to be low with average annual exposures estimated to be less than 1 rem/a (Frost, S.E. [et al], 1981). However, two developments are taking place which affect the potential significance of external radiation fields in the uranium mining environment. The first development stems from the most recent system of dose limitation developed by the ICRP which is intended to limit the workers' overall risk from exposure to ionizing radiation through the adoption of a sum rule (ICRP 26, 1977) which combines external and internal radiation exposures. In the case of exposure to radon daughters the sum rule will have the effect of reducing the annual exposure limit below the recommended limit by an amount that depends on external radiation and other sources of internal exposure such as the inhalation of ore dust (ICRP 1980). The Atomic Energy Control Board of Canada (AECB) is reviewing this subject and is expected to produce its recommendations shortly. Irrespective of the form of the sum rule eventually adopted by the AECB, it is clear that the net effect of the sum rule will be a collective reduction of the individual dose limits for individual exposure pathways. The second factor is the increasing development of high grade uranium deposits in Northern Saskatchewan. Some of these ore bodies have an average ore grade of 1% to 5% U308 or greater. Since the potential external radiation fields increase in proportion to the ore grade, it is apparent that increased effort in radiation protection planning is required in order to develop safe yet workable methods for mining and milling such ores. This paper is intended to provide information which can be of assistance in the formulation and development of a mining and milling plan. The principal focus of the paper is source identification and the design of radiation protection measures to limit external gamma radiation exposure. The exposure of workers to external beta radiation fields is also discussed. The paper is organized as follows: - Section 2 deals with source characterization. - Section 3 discusses the effects of finite source size and distance (i.e. geometry effects). - Section 4 presents selected data that are useful in evaluating shielding requirements. - Section 5 discusses the potential beta radiation fields. - Section 6 discusses practical data requirements for worker exposure scenarios. - Section 7 presents a variety of work exposure calculations. - Section 8 is a summary of this paper. 2. SOURCE CHARACTERIZATION This section develops the basic formulae for estimating the fluxes and doses from external gamma radiation. The calculation of the radiation flux due to a distributed source (i.e. a linear, area or volume source) as a function of distance assumes that any distributed source can be treated as a summation of point sources. [ ] Uranium ore contains radionuclides from both the decay chains of U-238 and U-235. In this paper the radioactive daughters are assumed to be in secular equilibrium with the uranium parent. (If natural thorium were present in the ore in significant quantities, the gamma rays originating from Th-232 would have to be added to the gamma rays from the uranium series). In all, there are over 50 separate gamma rays (as well as alpha and beta particles) emitted from the U-238 and U-235 radioactive decay series (USHEW 1970). The total

Jan 1, 1981

By Thomas D. Kaufmann

The 1982 recession set the US mining and metals industries reeling. Will the oncoming recession of 1991 hit as hard? Probably not, thanks to a shallower downturn, a weaker dollar and remarkable lower costs. Effects of the last recession That the 1982 recession was traumatic to the American mining and metals industry is an understatement. Quantities of metals consumed dropped. Metals prices fell despite continuing general inflation. The resulting real gross revenues of producers of each of the major metals plunged, in the trough of 1982, to levels one-fourth to two-thirds of those of the peak of 1979 (Table 1). By contrast, most industries in the United States were not hit anywhere nearly as hard. Real GNP, the aggregate of all production, slipped only 1 % from 1979 to 1982. Metals are most sensitive to the business cycle because of their applications. All metals but gold are raw materials to downstream industries. Raw materials are victims of strong fluctuations. This is because buying industries try to hold high inventories in boom periods when goods are in short supply. They reduce inventory levels in buyers markets when suppliers have idle capacity and raw materials are in ample supply.

Jan 1, 1990

By Peter Chou, Pooyan Asadollahi, Danny Lin

To maintain flexibility and ductility of tunnels crossing active faults, various mitigation measures are being utilized depending on fault offset movements and seismic design criteria. Examples of those approaches are simple bell and spigot joint, articulated joint, and complex deformable longitudinal bolt and spring joint system with seismic isolation washer. This paper presents a summary of tunnel fault crossing mitigation approaches and design considerations using previous relevant experiences in California as well as case histories from Japan, Taiwan, Turkey, Greece, and Italy found in literatures. Comparisons are made between large and small diameter tunnels, transportation, and utility tunnels, as well as bored, mined and cut-and-cover tunnels. Recent innovations, such as Japanese and Italian techniques, for tunnels crossing active faults are also discussed.

Jun 13, 2021

By C. R. McKee

In-situ mining of hard rock deposits will only become successful as we understand the engineering parameters involved and the design limitations they impose. As recognized by Wadsworth1 the most critical area is the enhancement of permeability in a hard rock mass. Along with creating permeability, the appropriate flow and fragment size conditions must be generated to insure economic rates of mineral recovery. In this article our interest is confined to true in-situ processes in which boreholes are drilled from the ground surface or a mine drift to deeper strata. We assume that fractures and permeability enhancement will be due to explosives detonated in boreholes. Other techniques such as hydraulic fracturing do not produce the necessary size distribution to promote economic extract ion rates unless the medium is already highly fractured and interconnected. Notable exceptions where hydraulic fracturing is applicable are many oil, gas and salt deposits. For many in-situ processes, an array of explosive charges offers the opportunity of creating a distribution of many fractures not achievable by other techniques. Such a situation would be suitable, for example, to in-situ mine hard rock gold, uranium, copper or oil shale deposits and may enhance oil and gas recovery in certain situations. The purpose of our article is to review and extend the explosive permeability theory of McKee and Hanson 3,4,5 and to apply its results to derive design parameters suitable for in-situ mining.

Jan 1, 1981

By J. Gibson

"INTRODUCTION As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action towards decreasing GHG and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery powered A/C systems and diesel-fired heaters, going no-idle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, stand-alone mobile equipment HVAC. THE HISTORY OF GHGS AND CLIMATE CHANGE In 1896 Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960’s Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Figure 1). In 1988 the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgement of a rising global annual temperature. The IPCC consists of over 2500 scientific and technical experts from more than 60 countries, and because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998 requiring all participating countries to reduce their GHG emissions by at least 5% from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States)."

Jan 1, 2015

By S. Anderson

Advances in inexpensive computer automation led to the development and utilization of a computerized ore control system at Cyprus Coppers tone Gold Mine near Parker, Arizona. These new ore control practices improved accuracy, performance, and productivity of the ore control effort. An automated system for data collection, including bar coding of blast hole samples, laboratory analysis, data management, grade estimation, cut delineation, and ore zone stakeout, plays a major role in ore control practices. This is of particular interest because of the large amount of blast hole information being processed, analyzed, and reported daily.

Jan 1, 1991

By G. R. Luster

In most current practice, the methods that are employed in technical evaluations of cement raw materials are deterministic; i.e., decisions among alternative raw mixes and alternative plant designs are reached with the aid of only "average" compositions and "representative" samples of the available raw materials. Nevertheless, cement plants are sensitive to raw-material variability, and uniformly high-quality raw materials are not so abundant as they once were. Some simple examples will illustrate how geological techniques can be combined with geostatistical and operations-research approaches to customize mining and processing systems to deal with variable raw-material compositions.

Jan 1, 1987