Search Documents

By D. Tahija

"Hecla's Greens Creek silver-gold-lead-zinc mill began using carbon dioxide rather than sulphuric acid to control pH in April, 2015. High pH levels in the grinding and lead flotation circuits are caused by the presence of re-mined cemented paste backfill in mill feed and need to be lowered to achieve good flotation response. Carbon dioxide has proven to be quite effective at controlling pH in the lead circuit with greatly improved pH target attainment. The allowable amount of carbon dioxide used is not limited by effects on lead-zinc selectivity and by poor froth characteristics, as was the case with sulphuric acid. Startup and implementation went smoothly, with few operational issues needing to be resolved. Early results from implementation of the system and its effects on mill performance will be presented. INTRODUCTION Hecla Greens Creek is a silver-gold-lead-zinc mine producing flotation lead and zinc concentrates, as well as a gravity gold concentrate. Besides their base metal contents, both the lead and zinc concentrates carry precious metals. The circuit is largely conventional, with SAG and ball mill grinding being followed by graphite removal preflotation, then conventional lead flotation and conventional zinc flotation. Both rougher concentrates are treated in regrind steps, followed by cleaner flotation. The cleaners tails are treated in an unorthodox bulk circuit to produce a low-grade zinc-lead concentrate marketed to Imperial Process smelters (1). BACKGROUND Backfill and Flotation pH The Greens Creek mine is an underground operation in which mined areas, after ore extraction, are backfilled, using rammed paste or pumped slurry. The backfill consists of mill tailings to which approximately five percent Portland or similar cement is added to enhance its compressive strength. Later mining near backfilled areas inevitably results in a considerable amount of old backfill being mixed with new ore before being shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed is often 20% to 25% and sometimes even higher. Commercial cement, and consequently backfill prepared using it, contains excess lime. Because of this, backfill in mill feed is indistinguishable from the addition of a large amount of lime, so mill natural pHs often range above 10 or even 11. Similar situations have been recognized for many years at mines throughout the world (2)."

Jan 1, 2016

By G. W. McMahon

Following the Sago Mine accident, the U.S. Mine Safety and Health Administration (MSHA) asked the U.S. Army Engineer Research and Development Center to study several possible methane explosion scenarios in the Sago coal mine. The study used a 0.3-m (1-ft) resolution map of the mine to produce a 3-dimensional (3 D) model of a portion of the mine, including the sealed area where the explosion occurred. An advanced 3 D computational fluid dynamics (CFD) code was used to calculate the explosion pressures within the sealed area, on the mine seals and in nearby regions of the mine. Based on the best available information on methane concentrations and assumptions on homogeneity and on layering and mix composition, three separate initial conditions of methane-air concentrations and location were studied. This paper discusses the CFD modeling technique, the results of the calculations, the challenges of conducting this type of modeling and the advantages and limitations of CFD modeling of accident investigations of mine explosions.

Jul 1, 2010

By Saul J. Escalera

Mechanisms involved in the depression of the sulfides: pyrite, chalcopyrite, galena and sphalerite with potassium permanganate have been investigated. Flotation tests were conducted using potassium amyl xanthate, Z-6, and pine oil in the absence and presence of potassium permanganate at around pH = 6. 5 naturally yielded by the sulfides in the pulp. On the basis of crystal chemistry considerations, the amount of xanthate adsorbed by the sulfides depends on the amount of sulfur and metal ions present on the surface; thus, the avidity of the sulfides for xanthate should increase in the order: sphalerite C chalcopyrite 4 galena 4 pyrite, and the ease of depression response to the permanganate action should be in the same order. Depression of the sulfides in the system occurs primarily due to the removal of the collector ions by the permanganate ions to form manganese dioxide and dixanthogen according to the reaction: 3 M(RX)2 + 2 Mn04 + 4 H20 2 ? MnO2 + 3(RX-XR) + 3 M+2 8OH where M represents the metal ion, RX the xanthate ion and (RX-XR) the dixanthogen molecule. Results seem to indicate that the permanganate ions play a triple role in the system: (1) they convert xanthate ions into dixanthogen, (2) they further oxidize the mineral surface and (3) if present in excess, they may oxidize the xanthate beyond the dixanthogen stage with the formation of CO2, H20 and SO4. All sulfides, except for chalcopyrite, showed a depression response in the order predicted regardless of the order of addition of xanthate and permanganate reagents. Chalcopyrite did not depress as easily; this behavior may be due to the avidity of the colloidal MnO2 to adsorb Cu+2 ions on its surface, this would destabilize the colloid making it coalesce with the formation of a layer of precipitated MnO2 on the surface of the mineral. The presence of this layer would prevent further action of the permanganate ions on chalcopyrite.

Jan 1, 1970

By M. Canty

Results are presented that were gathered during pilot-and field-scale testing of an innovative technology, sulfate-reducing bacteria (SRB), designed to treat and control acid mine drainage (AMD). The project was performed under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy through an Interagency Agreement. The MWTP is implemented by MSE, Technology Applications, Inc., located in Butte, Montana. Sulfate-reducing bacteria, a common group of anaerobic bacteria, produce hydrogen sulfide and bicarbonate when supplied with sources of carbon and sulfate. Hydrogen sulfide reacts with metal ions in AMD, precipitating them as metal sulfides; the bicarbonate serves to help neutralized the drainage. Pilot-scale testing was performed within eight packed-bed reactors at a temperature representative of a field application of this technology in a northern climate, nominally 8°C. The reactors, packed with an organic substrate, were operated continuously in upflow configurations receiving AMD at a flow rate corresponding to a 5-day retention time over a test duration of 60 days. During this time, numerous physical and chemical parameters were monitored. Pilot-scale metal removal efficiencies reached 99% for zinc, 99% for aluminum, 96% for manganese, 98% for cadmium, and 96% for copper. Iron and arsenic removal was not as effective as the aforementioned metals, which was largely attributed to the high levels of iron and arsenic contaminating the organic substrate. Evidence existed that both adsorption and sulfate reduction were occurring within the reactors.

Jan 1, 1998

By T. C. Vogt

The past history of uranium production has been dominated by strip and shaft mining methods, but recently in-situ leaching has emerged as a viable alternative for uranium recovery. (1-8) Mobil was the first company to start in-situ uranium leaching in New Mexico. Mobil's Crownpoint project areas are in Mdinley County and are part of the Grants Mineral Belt. The major uranium deposits in this area occur in the Westwater Canyon Member of the Jurassic Morrison Formation. (9-11) The ore depth at the Crownpoint project is about 2000 ft. In an earlier paper we discussed the uranium mineralogy of an areally broad sampling of Crown- point ore. (12) The organic carbonaceous material often associated with the coffinite ore was characterized in some detail. The organic material appeared to be a very mature, coaly-type kerogen derived from plant components. This result was consistent with other studies on such carbonaceous material. (13-15)

Jan 1, 1981

By Vic Miller

Highly variable milling properties within a geologically complex porphyry copper deposit owned by Kennecott Corporation in Nevada made it necessary to estimate the copper recovery and concentrate grade in areas where actual test data was lacking. The estimation was made by first determining the relationships between the desired metallurgical properties and the ore's petrology (i.e. copper mineral type, rock type and copper grade). This relationship was then combined with the already estimated rock type, mineral type and copper grade data in the mineral block model to predict the milling properties.

Jan 1, 1983

By P. S. Newall

As part of a much larger research project, factor analysis was employed to help interpret and compare the geochemical signatures produced by two different sample media; a traditional -80# soil fraction, and a coarse float. Both sample types were collected by hand auger from the extension zone of the Redmoor sheeted-vein complex and analyzed -for 19 major and trace elements. The rationale behind the study infers that the geochemical anomalies produced by wallrock alteration around such targets can be better detected in the lithogeochemical rather than the soil environment, sometimes at considerable distance from their source.

Jan 1, 1991

Mineral processes are relatively simple and metallurgical accounting would also be simple if it were not for the nature of the raw materials and the large scale of operations. Essentially the balance between input and output requires only weighing and assaying of the feed, salable products, and waste. but because of complexities to be described in the following pages there are few plants that do not encounter difficulties that cause some sacrifice of precision for economy and practicality. In arriving at a sound compromise, capable

Jan 1, 1985

By M. Moats

Copper electrowinning operations have dramatically improved their ability to produce high quality copper at low costs over the past several decades. Even so, some fundamental knowledge is still lacking that could allow operations to run even more efficiently. For example, a rule of thumb exists that estimates a current efficiency loss of 2-3% per gram per liter of iron in the electrolyte. While several laboratory studies have been performed that demonstrate this rule of thumb is likely true, no definitive relationship exists. In this paper, the first steps in developing a definitive relationship are presented. The effective diffusivity of ferric ions in synthetic copper electrowinning solutions was measured using chronoamperometry and the Cottrell equation. The effective diffusivity of ferric ion was determined as a function of electrolyte concentration and temperature. Synthetic electrolytes were then used in laboratory-scaled copper electrowinning experiments, where relationships between current efficiency and solution composition were found to exist under stagnant conditions. Key words: Copper electrowinning, Current efficiency, Chronoamperometry, Ferric ions

Jan 1, 2009

By Mark Van Dyke, Mark Mazzella, Gamal Rashed, Nicole Evanek, Brent Slaker

In the past decade, there have been several incidents of massive ground collapses in underground stone mines in the eastern United States. Fortunately, these events have not resulted in any fatalities. However, three mine workers were injured and many others were at risk due to the hazard from the fall of ground and/or the airblast associated with these massive collapses. The National Institute for Occupational Safety and Health (NIOSH) initiated a project to better understand the causes of these massive ground collapses to help prevent their future occurrence. The main objective of this study is to investigate the main factor(s)that initiated one of these massive ground collapses. The authors relied on several tools including three-dimensional (3-D) LiDAR scans for the surface subsidence feature and the underground mine workings around the collapsed area, borescope data at multiple locations around the collapse, S-Pillar analysis for average and unfavorable conditions, and numerical models. The emphasis has been placed on the impact of the following limestone pillar stability parameters: pillar width-to-height (W/H) ratio, benching, the existence of karst features, weak roof, and geological discontinuities. 3-D LiDAR scans were utilized to show the shape and the extent of karst cavities observed within stable pillars around the perimeter of the collapsed area. Together, this coupling of field measurements and observations and modeled systems suggests the potential causes of the collapse.

Jul 1, 2023

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By George E. Valadão, Iván A. Reyes, Mizraim U. Flores, Armando C. Araujo, Rubén H. Olcay

Dewatering tailings to higher grades than paste produces a stable deposit that typically does not require retention dams and is called a “dry stack.” A proposal of different dewatering techniques applied in the fine tailings produced after final desliming phase, obtained from the treating of phosphatic ores, is the main objective of this work. The dewatering techniques evaluated were column thickener, deep cone classifier, and hyperbaric filtration. Calcite and dolomite were the main mineral contained in the phosphate tailings and these have a very fine granulometry; the tailings presented different behaviours related to the dewatering technique applied. The test column thickener and deep cone classifier with the best operational parameters found to obtain a maximum percentage of solids in mass were ~ 71% and ~ 67%, with values of yield stress ~ 200 Pa and ~ 100 Pa, respectively. In the hyperbaric filtration, a cake with ~ 10% moisture was obtained. This indicates that the transportation conditions are not the same. The overflow turbidity levels obtained from column thickener and deep cone classifier test did not exceed the value 100 NTU, whilst for the filtrate of the hyperbaric filter obtained values ~ 800 NTU. It was possible to preliminary estimate the recovery direct of water, considering each dewatering technique for final disposal of the tailings. The best dewatering techniques obtained were in the following order for the disposal in phosphate fine tailings dams; the hyperbaric filter showed an excellent dewatering capacity with productions rates around 160 kg h− 1 m− 2 for moisture cake of 10%, followed by the column thickener and deep cone classifier with paste ~ 71% of solids (W/W) and high-density slurry ~ 67% of solids (W/W), respectively.

Dec 23, 2023

By N. J. Ferguson

An upsurge in demand for Australian coal has seen a much needed programme for a new generation of coal ports. This paper discusses design concepts in planning a large modern terminal, with the 25 Nt/a Port Kembla and the 50 Mt/a Newcastle facilities as practical examples. The need is emphasised for a studied Master Plan, in-built materials handling flexibility and staged development. Trends in bulk ship design and loading methods are noted. Features of these Australian designs include methods of dealing with poor ground conditions, functional civil engineering for environmental protection and optimal marine structure designs.

Jan 1, 1982

By Manoj Khandelwal, Minghui Liu, Jian Zhou, Kun Du

The waste rock and tailings backfill into the mined-out areas are the most effective method for solving the environmental pollution and surface disasters for nonferrous metals mines. In practice, the success and availability of backfill operations are dependent on the slurry fluidity and the strength properties of cement backfill. The transport of the slurry through the pipeline to the designated backfilling area relies on its eximious flow properties, while the appropriate strength of the filling body ensures the safe operation of the stope. In this paper, the effects of cement and aggregate types on the slurry fluidity and strength characteristics of cemented backfill are studied in detail, which are often ignored in other pieces of literature. Diffusivity is used as an indicator to evaluate the slurry fluidity. Various slurries whose concentrations ranging from 70%, 73%, 75%, 78%, and 80% are made with different aggregate ratios and cement-sand ratios are tested. It has been shown that slurry fluidity is inversely related to its concentration, but 78% is the “stopping point” for the deterioration of fluidity. The addition of rod-milled sand improves or worsens the cemented backfill (CB) strength depending on the amount of rob-milled sand. The uniaxial compression experiment results on 216 CB specimens produced by different combinations of influencing variables showed that CB specimens made from cement with superior mechanical properties have a higher uniaxial compressive strength (σucs). It has been also found that the effect of aggregate ratio on the CB strength is not singular, but works in conjunction with the curing time and the cement-sand ratio. The longer the curing time and the higher the cement content, the higher the CB’s σucs. To avoid the time-consuming and costly problem of obtaining the strength of the CB from indoor experiments, an SVR model capable of predicting the uniaxial compression strength of CB specimens is proposed, which is optimized by genetic algorithm (GA) and particle swarm optimization (PSO) algorithm. The results of the three performance indexes (MAPE, MSE, and R2) show the superior performance of the GA-SVR and PSO-SVR models and the agreement of the predicted results with the experimental results, which indicate that these two models can accurately predict the σucs of CB.

Feb 3, 2022

By R. F. Korcak

There exists a wide array of industrial by-products that can be shown to produce beneficial responses in the soil/plant environment. These materials range from clean coal technology residues produced in the generation of electric power, particularly those high in gypsum, to mineral 'fines' produced by the aggregates and crushed stone industries. A number of these materials will be examined in relation to potential nutritional interactions in soils and crops with emphasis on trace elements. The significance of utilizing these materials in agriculture as a component of sustainable agricultural systems will be discussed.

Jan 1, 1995

By Don Runge, John T. Zeni

Cuprex Limited is currently developing a small gold mining operation in Central Australia in the Tennant Creek field. In February 1984, the company undertook a feasibility study on the project and operations commenced in August 1984. Ore reserves are located between 230 and 280 metres (755 ft and 919 ft) below surface and ore extraction required the establishment of a shaft network for access, ore hoisting and ventilation. Zeni Drilling Company from West Virginia, U.S.A. was contracted to blind drill two shafts for the project. Blind drilling was selected for various reasons, including timing which related to cost efficiency. The blind drill shaft technique has proved successful in this application and with enthusiastic and innovative support from the mining industry, will prove an efficient and cost effective means of accessing and operating underground mining projects of all sizes in the future.

Jan 1, 1987

By S. Torno

The elimination of ultrafine (<10 µm) clay particles is essential to the treatment of abandoned coal-washing plant tailings for the recovery of the remaining coal fraction by enhanced gravity processing. Effective hydrocyclone classification is required to remove this fraction. The highly variable composition and particle size distribution of such wastes creates significant difficulties in the operation of hydrocyclones for such classifications. Hydrocyclone laboratory investigations and their plant setup require lengthy or time-consuming tests. The use of empirical models of such classifications frequently requires modification to correspond to actual operating conditions. Results of the evaluation of computational fluid dynamics (CFD) modeling to predict hydrocyclone classification of coal-washing plant tailings are presented. Results of the standard k-epsilon turbulence, SSG turbulence and large eddy simulation CFD models are compared with the results obtained from analyzed hydrocyclone classifications. The CFD models tested are shown to be very effective in the simulation of hydrocyclone classifications for the determination of the classification particle size and adequate for determining the efficiency index values for many applications. The large eddy simulation model was identified as the most precise, but it is recommended that all three models be improved simulations of classifications above and below the classification particle size.

Jan 1, 2011

By F. Calizaya

This study summarizes the results of various numerical and laboratory experiments per-formed to study the effect of airflow recirculation on gas concentration. The numerical exercises were carried out on a simulated mine ventilation net-work. The laboratory experiments were conducted at the Mackay School of Mines&apos; airflow monitoring system in Reno, Nevada. In both cases, the airflow was recirculated through the system by means of a main fan and a set of booster fans. The booster fans were positioned to produce two types of recirculation: In line and Cross-cut. For each type, various recirculation conditions were generated by changing the booster fan pressure. During each test, the gas emission rate at the simulated working face was kept constant. The study illustrates the conditions under which controlled airflow recirculation may be used to solve a district ventilation problem.

Jan 1, 1991

By Kyeong Woo Chung, Rina Kim, Ho‑Seok Jeon, Yeongjin Ahn, Byunghun Go, Min‑seuk Kim, Hong‑In Kim, Sujeong Lee, Yuik Eom

The study focused on the recovery of vanadium from a Korean vanadium-bearing titaniferous magnetite (VTM) ore, examining the behaviors of magnetic separation and Na2CO3 roasting-water leaching. Two concentrates were prepared using single-stage dry magnetic separation and three-step wet magnetic separation, resulting in V2O5 grades of 0.8% and 1.0% and major gangue mineral SiO2 contents of 6.5% and 1.7%, respectively. These concentrates were subsequently roasted at 1050 °C with the addition of Na2CO3 and then water-leached at 25 °C. Various stoichiometric ratios of V2O5 to Na2CO3 were tested, ranging from 1:1 to 1:40 of the theoretically required amount. As the amount of Na2CO3 increased, the vanadium leaching efficiency showed fluctuations between 4 and 35% for ratios of 1:1 to 1:10, while it linearly increased from 4 to 82% for ratios of 1:10 to 1:40 in the leaching of the low-grade concentrate. In contrast, the leaching efficiency increased from 47 to 74% for ratios of 1:1 to 1:8 and then sharply rose to 84% at a ratio of 1:10 in the leaching of the high-grade concentrate. Subsequently, it reached a plateau of 92 to 94% for ratios of 1:20 to 1:40. The difference in leaching efficiency was primarily due to the reaction of gangue minerals with Na2CO3, which hindered vanadium leaching from the VTM concentrates. This hindrance was notably more pronounced in the low-grade concentrate with the lower salt ratio, as the gangue minerals exhibited a preference for consuming Na2CO3 over vanadium. The mineral formation was analyzed in detail using XRD and MLA to shed light on the mechanism of different vanadium leaching behavior depending on the concentrate grade and vanadium to salt ratio. Based on the results of this study, it is evident that applying a proper magnetic separation procedure is significant to achieving satisfactory vanadium recovery with less salt amount by removing gangue minerals ahead.

Mar 15, 2024

By S. Vogely, J. Trescot, D. Connor, F. Beloy

In 2001, the Minntac Division of US-Steel retrofitted one of their Grate-Kiln Iron Ore Pelletizng lines with a Ported-Kiln Air Injection System (PKAIS) the first of it’s kind in the world for oxide pellets. The Ported Kiln System injects air under the bed of pellets in the rotary kiln, causing rapid oxidation of the magnetite pellets. This rapid oxidation allows for lower kiln temperatures, reducing fuel demand; less heat load on the annular cooler; and higher pellet quality. Both the process and the equipment are patented developments by Metso Minerals. This paper discusses the process, the key equipment, and the benefits to the pellet plant and the downstream blast furnace operations.

Jan 1, 2004