Search Documents

By D. R. Lanners

Samples of the same coal measure overburden spoil were obtained from three different mine sites. Site A used a 27-m3 tub-mounted dragline, Site S used a front-end loader and truck combination, and Site C used a 6-m3 crawler-mounted dragline. The spoils were analyzed in the laboratory for the strength parameters using drained triaxial tests conducted on 150-mm diameter specimens. Regression analysis was utilized to determine the appropriate failure criterion for the strength data from each site. Spoil obtained from Site S yielded higher shear strengths than Sites A and C.

Jan 1, 1993

By M. W. Harmer

Laboratory test work, pilot plant testing and plant experience with wet, fine mesh screens is discussed. High frequency, low amplitude, fine mesh, wet screens were installed on the 6th cleaner concentrate stream. These screens produce a 60% oversize recovery split of the molybdenite concentrate that is of leached equivalent quality. The undersize stream is leached with 'hot ferric chloride to remove Pb and Cu contaminates before roasting or shipment to sulfide customers. This plant modification is a good example of using existing technology in an unconventional flow sheet to yield significant cost savings.

Jan 1, 1990

By Z. Xu, Z. Li

Colloidal interactions play a critical role in mineral processing, including grinding, physical separation (particularly flotation), dewatering, and tailings management. Despite great energy input in comminution to liberate valuables from gangues, heterocoagulation between valuables and gangues would prevent the separation of valuables from gangues. On the other hand, selective coagulation/flocculation to increase the size of desired fine particles could enhance physical separation and dewatering, while dispersion is needed for fine grinding. To control the state of colloidal dispersions by creating favorable conditions, it is of paramount importance to study colloidal interactions in a relevant system and understand underlying mechanisms. This review summarizes recent advances in developing the-state-of-the-art techniques and novel methods of measuring colloidal forces, including atomic force microscope, surface force apparatus, zeta potential distribution measurement, quartz crystal microbalance with dissipation, and our recently developed integrated dynamic force apparatus. The basic principle of each technique was introduced first, followed by a summary of critical information derived for the relevant mineral processing systems. Finally, the pros and cons of each technique were discussed to emphasize the use of complementary techniques that assist in solving fundamental problems in mineral processing.

By J. P. P. Silva

Sodium silicate (water glass) is a modifier reagent widely used in flotation with the function of a depressant or dispersant. The interaction between sodium silicate and mineral surfaces is still not well understood. This investigation aimed to illuminate the sodium silicate action mechanism as a depressant in the flotation of the minerals quartz and calcite. The experiments were done with high-purity mineral samples in the particle size range below 147 µm. The microflotation tests in a modified Hallimond tube showed that, in all systems tested, the efficiency of sodium silicate increased with the concentration. At concentrations above 1,500 g/t, almost total depression (96% for calcite and 97% for quartz) was achieved. The variation of sodium silicate modulus did not alter the quartz flotation performance in the presence of amine (150 g/t). The most efficient depression pH range was observed between 5 and 8. Above pH 10, the depressant action of sodium silicate was negligible. The infrared spectra obtained at pH 7 after silicate contact showed the presence of the groups OH and Si-OH, both suggesting that the adsorption of the neutral species Si(OH)4, as well as siloxane groups (Si-O-Si), attributed to adsorption of polymeric species. Sharing electron pairs is the proposed adsorption mechanism between Si(OH)4 and polymeric species and the surface sites (Si-O on quartz and Ca-O on calcite). At pH 11, the electrostatic repulsion prevents the species adsorption, impairing the sodium silicate action.

By F. L. Bazzanella

Cyprus Pima has two concentrators, one with a conventional crushing-grinding circuit and the other using semi-autogenous grinding followed by ball mills.

Jan 1, 1978

By Curt Swanson, David C. Mathy, Dru R. Nielson, Kent VonAspern

In 1997, Central Contra Costa Sanitary District undertook the design of the Martinez East Side Trunk Sewer Improvements Project. Microtunneling was specified for approximately 1,035 meters (3,400 feet) of 600-mm (24-inch)diameter pipeline to be installed through estuarine soil deposits (San Francisco Bay Mud) and alluvium beneath the congested city streets of downtown Martinez, California. Directional drilling was specified for approximately 275 meters (900feet) of 200-mm (8-inch) diameter pipeline in four separate segments to be drilled through bedrock within narrow utility easements between residential properties. This paper presents a case history for the design and construction of themicrotunneling and directional drilling aspects of the project.

Jan 1, 1999

By Oscar Cabello, Luis Mendieta, Maribel Guzman

Mineral flotation processes generate large volumes of tailings, which must be disposed of efficiently and safely. In addition to dry stack disposal, the possibility of reusing these tailings as aggregates in shotcrete is an interesting alternative. Tailings samples from a mining operation in southern Peru were characterized by granulometric analysis, X-ray diffraction and Scanning Electron Microscopy. Concrete samples were obtained with different tailings formulations. The samples were subsequently subjected to geomechanical testing. The results showed that replacing 20% to 30% of the tailings with aggregates in shotcrete production achieved compressive strengths exceeding 30 MPa after 28 days of curing, with an energy absorption capacity of 500 joules. Results show that this shotcrete can be used in the support stage of the mining cycle in underground mining.

Feb 22, 2026

By George P. Tateosian

Merchants perform a number of functions in the copper market. As a major distribution arm of the copper industry, they secure scrap and other copper bearing materials for processing into usable refined shapes. These are ultimately sold to fabricators. Merchants ' hedging and arbitrage activities help keep values in proper relationship from product to product or region to region. Through these switching and trading operations, they optimize the flow of copper from mine to consumer. And finally, merchants act as a repository for copper units during times of surplus and a stockpile from which to draw during tines of shortage.

Jan 1, 1979

By NEHA PANDEY, Sunil Kumar Tripathy, ARIJIT BISWAS

Due to the growing market of Electric Vehicles (EVs), there is a rise in battery demand. Nickel can be used as a potential element in cathode for lithium-ion batteries. Nickel can provide thermal stability, high energy density, and conductivity in cathodes of lithium-ion batteries. Low-grade chromite overburden from Sukinda mines contains less than 1 wt% of nickel, which can be utilized to extract nickel. Recovery of nickel from such low-grade overburden can help in value addition. The present study provides deeper insight into the aspects of extraction of nickel product derivatives (NPDs), mainly mixed hydroxide product (MHP), through the hydrometallurgical route. The current study focuses on extracting nickel and cobalt from a mine overburden with 0.41% nickel with major silicate gangue. MHP can be processed further for nickel sulfate production, a potential raw material for cathodes in EV batteries. The study discusses a process flowsheet to recover nickel and cobalt from overburden through atmospheric leaching with pre-calcination. It is observed that the step of pre-calcination improves the effective recovery of nickel from overburden. The leaching reactions are effective at a temperature of 90 °C and 1 atmosphere pressure. The orthophosphoric acid was used as a lixiviant for the selective recovery of nickel and cobalt from overburden. Recovery of nickel and cobalt obtained at optimum conditions is 84.0% and 39.9%, respectively. The iron impurity in the leachate solution is 1.27%. It is concluded that the process with pre-calcination along with acid leaching is effective for extracting nickel and cobalt at atmospheric pressure.

Dec 28, 2023

By Sammie D. Guy

This paper discusses the subject of "Improving Contracting Methods" from the owners point of view, particularly the public. An overview is given of the work of the U.S. National Committee on Tunneling Technology and some apparent results of the implementation of these recommendations or lack thereof. Selected recommendations that are not being implemented are discussed as to the the desirability and the possible impact of their implementation. Impediments to acceptance of the recommendations are identified and solutions proposed. The difference in the flexibility, attitudes and approaches of owners, public, quasi-public and private, toward improving contracting methods are discussed. Particular emphasis is given to the fact that the onus to improve is on the owner because they usually develop the contractual language or at least have the final decision on its content and are or should be an equal party to the contract during its administration.

Jan 1, 1983

By J. A. Porter

This paper uses project examples, primarily associated with large iron ore mines in Brazil, to demonstrate opportunities for the mining industry to go beyond traditional compliance and impact mitigation to proactively operate within the ethics of environmental and economic sustainability.

Jan 1, 1994

By Muhammad Zia-ur Rehman, Sajjad Ahmad Baig, Gao Lei Fu, Muhammad Mohsin, Sobia Naseem

The environmental sustainability is linked back to human sustainability; the sustainability development comprises the environment, society, and economics. This study mainly focused on mining sustainability and its impact on the environment of Pakistan. For measuring the level and environmental mining sustainability nature to Environmental Impact Assessment (EIA) of the world’s second largest salt mine “Khewra,” Folchi and Phillips environmental sustainability mathematics (PESM) models are applied. The results indicated that Khewra was deemed to be potentially sustainable for the environment and quality of salt. The results suggest the delicate balance of maintaining sustainability successfully, regarding the mining process in Pakistan which has been affecting the local environment and community so badly. The paper lays emphasis on the potential significance of the model’s application for the attainment of sustainable mining goal. This study is essential for researchers,

May 11, 2020

By C. A. Oestreicher

For sulfide minerals, the presence of dissolved oxygen in the water phase is an influencing factor for separation by flotation. Klassen and Mokrousov(I:217l distinguish three stages of oxygen adsorption; namely, reversible adsorption, activated adsorption and, finally, surface oxidation. While contraversial, limited adsorption of oxygen is believed to improve the interfacial reactivity between collector and mineral. Intensive surface oxidation of sulfide minerals usually results in unsatisfactory flotation with collectors of the xanthate type. The influence of dissolved oxygen in the water phase has received consideration for sphalerite, galena, chalcopyrite, arsenopyrite, chalcocite, and covellite(2,3,4,5,6). However, the nature of surface oxidation products of sulfide minerals has received very limited investigation(6,7). Lightly oxidized galena promotes the adsorptive reaction of surfactant (xanthate or dixanthogen). Tolun and Kitchener(8) state that limited interaction occurs between galena and xanthate under relatively reducing conditions. And, that exposure to oxygen raises the electrochemical potential of the galena to that required for reaction with xanthate or dixanthogen. In the latter condition, the galena has an "effective flotation surface". On the other hand, intensive oxidation of galena reduces the chemical reaction with xanthate collectors (9) . Complete flotation with xanthate-type surfactants with increasing oxygen content in the water phase has been determined to have the following sulfide mineral sequence(3): galena, pyrite, sphalerite, chalcopyrite, pyrrhotite and arseno-pyrite. The work of Cusack(4) suggests that some threshold amount of oxygen is necessary for flotation to occur, but heavy oxidation hinders flotation with xanthates. According to Tolun and Kitchener(8) catalytic oxidation of xanthate to dixanthogen occurs. From infrared studies, Poling and Leja(IO,II) found that in the absence of oxygen in solution, xanthate ions do not adsorb either on

Jan 1, 1972

By Dennis C. Martin

Assessment of the potential for mining induced subsidence and determination of ultimate design requirements for a mining operation should be based on a number of assessment approaches. Although the rock mechanics engineer has a variety of limit equilibrium and numerical modeling tools available for assessment and prediction of subsidence effects, empirical approaches based on precedent experience provide a powerful tool for calibration/verification of analytical models and prediction of subsidence. Three separate analyses approaches have been applied to the assessment of potential subsidence for a proposed block caving mine in eastern Canada. The investigations have included an assessment of documented historical information from previous block cave mining at the site, deterministic analyses using limit equilibrium approaches to assess kinematically possible failure mechanisms, and three-dimensional numerical modeling techniques. Analyses results have been used and compared with precedent experience and documentation of subsidence behavior from previous mining to optimize the subsidence predictions for the proposed mine.

Jan 1, 1998

By S. Shankar

Available literature on the effect of re-entrainment on overall airborne dust concentration in mine airways or the fundamental mechanisms of coal dust re-entrainment in mine atmosphere is scant. Therefore, as part of the Respirable Dust Center's ongoing research, a three part study was envisaged: study of the re-entrainment phenomena of anthracite and bituminous coal dust particles in a wind tunnel under the influence of varying air velocities; study of the same in the Lake Lynn Laboratory Mine of the USBM with both airflow and walking by personnel causing re-entrainment; and mathematical modeling and computer simulation of the re-entrainment phenomenon. In this paper, results from the re-entrainment studies in the wind tunnel and the Lake Lynn Laboratory Mine are presented. Further, the results from the wind tunnel studies are compared with the results from in-mine studies conducted at the Lake Lynn Laboratory Mine of the USBM. Comparing the results from the two studies it was observed that increasing air velocity increased the rate of re-entrainment, but increased time of exposure decreased the airborne dust concentration. Compared to same size particles, a mixture of sizes created more airborne dust concentration when re-entrained. It was also observed that contribution of airborne dust concentration due to airflow was negligible compared to the contribution due to walking.

Jan 1, 1995

By Ricardo Oliveira Gallart de Menezes, Claudio Gerheim Porto, Reiner Neumann

This study presents the results of the mineralogical characterization of Ti-Zr ore from the Jiboia deposit, located in the municipality of Brejo Grande, Sergipe State, Brazil. The goal is to identify the main Ti, Zr, and REE carrier phases in the different particle size fractions in order to subsidize the development of a cost-effective processing route for the production of heavy minerals concentrate. The mineral resources are estimated at 31.5Mt @ 3.5% of total heavy minerals (THM) for the Jiboia Ti-Zr deposit, of which 5 Mt @ 3.39% THM were classified as measured and indicated. The mineralogy of the heavy mineral concentrate recalculated to 100% is represented by 22% pseudorutile, 20% ilmenite, 15% zircon, 5% rutile, 2% monazite, and 36% gangue. The ore minerals are preferably concentrated in the 150 × 53-μm granulometric fractions, which represents 80% of the THM and only 27% of the ROM (Run-of-Mine) ore. Therefore, by cutting the ore to 150 μm, it is possible to discard 73% of the ROM mass and recover 80% of the THM, including 100% of the zircon and monazite which are the most valuable minerals present in the heavy mineral concentrate. The global recovery of THM starts to decline rapidly in the fractions finer than 106 μm and the mass disposal (tailing) does not follow in the same proportion. Higher zircon contents in the concentrates of the fractions finer than 150 μm imply a significantly lower recovery of heavy minerals like ilmenite, pseudorutile, and rutile that make the fractions coarser than 150 μm.

Jan 9, 2024

By Richard C. Marshall

The heightened concern over the environment which has developed in recent years has caused activities on National Forest lands to come under more intense public scrutiny. This has been especially true for activities oriented toward the production of commodities. Cattle grazing, mining, timber harvesting, and oil and gas leasing and drilling have all been increasingly subject to appeal and litigation. As a result, environmental analyses being conducted by the Forest Service have become more comprehensive, and measures to reduce or eliminate adverse impacts on resources have been given more attention. The costs of such environmental mitigation measures can be significant even when viewed in the context of the millions of dollars a company may spend, for example, to develop a mine. Using the Montanore Project in northwestern Montana as a case study, this paper examines the costs of alleviating some of the detrimental effects which may occur as a result of a mining operation. Although many of the general issues that have been raised about Montanore are common to other mineral projects, the scale of the project, as well as the fact that the ore body is within a wilderness area, the site is in grizzly bear habitat, and the surface waters are considered to be pristine, all combine to make Montanore particularly challenging from an environ- mental standpoint. Much of the information which follows is contained in the most recent version of the Draft Environmental Impact Statement (DEIS) which is scheduled to be published in several weeks. Based on agency and public comments, some of the information presented in the paper will change before the Final Environmental Impact Statement is issued in 1991.

Jan 1, 1991

By M. K. Mohanty, H. Akbari, L. A. Ackah

Dry separation was the predominant method of coal cleaning in the United States from the 1930s to 1980s. The application peak of dry separators for cleaning raw coal was in 1965, when about 23.1 Mt of cleaned bituminous coal was produced. The main advantage of dry coal cleaning is the elimination RIWKH GHZDWHULQJ VWDJHV DQG VLJQL¿FDQWO\ UHGXFHG moisture in comparison to wet processing. In addition, developed dust control systems have made dry cleaning method an environmentally friendly process. The largest air-based coal cleaning plant was built in Pennsylvania in 1968 and could clean 1,272 t/h of raw coal sized smaller than 19 mm. This was followed by a decline in dry coal cleaning to less than 3.6 Mt in 1988. Some of the main reasons that shifted coal operations IURPGU\WRZHWSURFHVVLQJZHUHWKHQHHGIRUPRUHHI¿FLHQW separations with lower density cuts, increase in raw coal surIDFHPRLVWXUHVSHFL¿FDOO\LQXQGHUJURXQGPLQLQJWRFRQWURO GXVW ¿QHUSDUWLFOHVL]HUHTXLUHPHQWV LQFUHDVHLQ¿QHVLQUDZ coal from underground mines, and health and safety concerns related to dust and noise (Arnold, Hervol and Leonard III, 1991; Miller, 2011).

By E. S. Forbus

A process for producing reductive bleach in-situ in kaolin slurries has been developed. The bleach is formed by mixing an iron sponge powder (-325M) with slurry treated with SO2. The process has been successfully demonstrated in production, and applied to several grades. The color, brightness, and viscosity of the bleached product is equivalent to or better than that of product bleached with commercial sodium hydrosulfite . The tested products can be bleached at a cost, which is 38-54% of those associated with the use of commercial bleach.

Jan 1, 1993

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2017