Search Documents

By Dominc C. Torre

INTRODUCTION Rapidly increasing capacities of equipment used to load and handle material at the face require improved haulage equipment and better methods of transporting the mined materials or "muck" to the shaft or slope and out of the mine to the processing plant on the surface. Increasingly, those transportation demands are being satisfied with underground belt conveyors. Such con¬veyors provide the most readily available, most efficient, and most reliable method of carrying materials in a continuous and rapid flow from the face loading equip¬ment to the surface plant. Almost universally, belt con¬veyors are used in coal mines and those nonmetallic and metallic mines operating in relatively flat bedded deposits. Belt conveyors are available in a wide range of capacities, mainly limited by belt width, belt speed, and weight of the material to be transported. They can be used on the level, on grades, on the surface, or under¬ground. They provide a rapid and constant flow of material, transporting the material as quickly as it is mined. Length of belt conveyors is almost unlimited. Where the haulage distance exceeds the practical capacity of a single conveyor unit, two or more conveyors can be used in series. Single conveyors more than 1.6 km (1.0 mile) long are common; multiple-unit conveyors in series operation are transporting materials over distances exceeding 16.1 km (10 miles). Depending upon mate¬rials being transported, job conditions, cost of the terrain being spanned, and alternative haulage methods avail¬able, conveyors can be conceivably economical for even greater distances. Table 1 lists maximum belt speeds recommended for most materials, relating belt speeds to belt widths. Table 2 lists capacities of typical conveyors of various widths and speeds, transporting commonly mined mate¬rials of various weights. ADVANTAGES OF CONVEYOR SYSTEMS For several years after their initial introduction, belt conveyors were available only with rigid side frames or a supporting structure of steel and concrete. That con¬struction limited underground applications, due to the cost and relative inconvenience of extending or retract¬ing the belt conveyor in the confined underground environment. However, during the last 20 years, wire-¬rope side-frame belt conveyors, as shown in Fig. 1, have become widely used in underground applications. Even wider use can be anticipated with their application to the fast movement of materials in surface mining operations. Advantages of the wire-rope side-frame belt con¬veyors were realized first in panel or section belt haulage in coal mines. Soon afterward, use of those conveyors was extended to gathering and main-line haulage. The mobility of the wire-rope side-frame conveyor is the principal reason for its success. The conveyor can be extended, retracted, dismantled, moved, and reassembled easily, even in relatively confined under¬ground spaces. The intermediate structure consists of rope support stands, wire-rope side frames, wire-rope tie-off stands, and the necessary carrying idlers and return idlers. An important and very attractive feature is the ability to suspend the conveyor from the roof in an underground mine, as shown in Fig. 2, leaving more room for improved housekeeping and allowing passage of face-service equipment, haulage vehicles, and other mining equipment. The conveyor's open construction allows quick and easy visual inspection of its com¬ponents for failures or malfunctions; it also facilitates checking and correcting conveyor-belt alignment. Other advantages contributing to the attractiveness and widespread application of wire-rope side-frame conveyors in main-line, slope, and surface installations include: lower capital costs, lower installation costs, lower maintenance costs, reduced impact on idlers and belting, reduced spillage and minimal cleanup, improved conformation to undulating terrain or mine bottoms, and the ability to span most obstacles without heavy structural support. CONVEYOR CLASSIFICATIONS Underground belt conveyors are classified normally according to their function. Generally, conveyors are classified into one of four main categories: 1) Panel or section conveyors normally receive the material to be transported directly from the face-haulage equipment. 2) Gathering conveyors are secondary haulage units that usually receive material from two or more panel conveyors. 3) Main-line conveyors transport all the material mined in the underground operations to the slope or shaft. Normally, they receive the material from two or more gathering conveyors. 4) Slope conveyors generally operate in tandem with the main-line conveyor, providing continuous Table 1. Maximum Belt Speeds Recommended for General Use Run-of-Mine Hard Ores and Belt Width, Coal and Earth, Primary Crushed mm (in.) m/s (fpm) Stone, m/s (fpm) 356(14) 1.52 (300) 1.52 (300) 406(16) 1.52 (300) 1.52 (300) 457(18) 2.03 (400) 1.78 (350) 508(20) 2.03 (400) 1.78 (350) 610(24) 2.54 (500) 2.29 (450) 660(26) 2.54 (500) 2.29 (450) 762(30) 3.05 (600) 2.79 (550) 914(36) 3.30 (650) 3.05 (600) 1067 (42) 3.56 (700) 3.05 (600) 1219 (48) 3.56 (700) 3.30 (650) 1372 (54) 3.56 (700) 3.30 (650) 1524 (60) 3.56 (700) 3.30 (650) 1676 (66) 4.06 (800) 3.81 (750) 1829 (72) 4.06 (800) 3.

Jan 1, 1982

"Cast blasting is the primary means of overburden displacement in a surface coal mine. It serves two purposes; fragmenting the rock and throwing it directly to its spoil pile using explosive energy. Increased throw minimizes costs by reducing the amount of material that needs to be re-handled. Prior studies have shown that by only changing blast hole timing with the same blast design, fragmentation and throw alters. It is necessary in cast blasting to optimize both fragmentation and throw, since larger fragments will require more wasted energy to throw the same distance. In an operating mine in Georgia, an optimum inter-hole delay for fragmentation has been found by studying timings from 0ms to 45ms. Instantaneous timing between holes increased the throw by over 100 ft, but fragmentation was poor. Shock and detonation wave collision is a potential reason for this increased throw. This paper investigates this optimized inter-hole timing while altering top and bottom column primer time to potentially improve throw while maintaining optimum fragmentation. Timings studied are top initiation, bottom initiation, and top and bottom simultaneously. INTRODUCTION Explosives are utilized extensively by the mining industry in order to break rock, as either ore or overburden, for hauling, loading, and crushing. An effective production blast strives to achieve optimum rock fragmentation in order to increase the efficiency and reduce the costs of those downstream operations, while simultaneously meeting environmental regulations. The goal of blasting with respect to fragmentation is, according to Hettinger (2015), “to decrease the average particle size of the fragmented rock without overly increasing fines or, in other words, improve fragmentation.” Additionally, the distance the rock is transported by the explosive energy from the blast, also known as throw, can increase efficiency by reducing the amount of material that is re-handled by mine equipment. The primary situation in which this is desirable is the cast blasting of overburden across the narrow pit of a surface coal mine. A key variable in a blast design pattern that can be manipulated to optimize both fragmentation and throw is delay timing between detonations. The invention and increased utilization of electronic detonators has allowed for precise delay timings to be used between rows, holes, and even multiple primers within the same hole. These recent developments in the blasting community have also provided an opportunity to investigate whether or not the mechanism of shock or detonation wave collisions caused by short timing delays are responsible for any increased fragmentation or throw. This experiment attempts to demonstrate if an increase in throw can be achieved while maintaining optimum fragmentation. This study consisted of 3 full scale bench blasts at a granite quarry in Talbotton, GA. Each blast was characterized by the timing delay between the top and bottom primer in the blast column of each hole; one simultaneous blast with a 0 ms delay, a bottom-initiated blast with a 1 ms delay, and a top-initiated blast with a 1 ms delay. Fragmentation analysis of the resultant muckpiles was performed using a combination of the PortaMetrics handheld point-and-shoot rugged tablet from Motion Metrics and the software WipFrag from WipWare. Throw was measured by placing strategic distance markers on the floor of the bench and then taking overhead photographs of the muckpiles after each blast. High-speed video footage was captured of each blast using an MREL Blaster’s Ranger II camera."

Jan 1, 2017

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

Technical Papers, Mining Engineering Vol. 49, No. 12, pp. 70-75, Discussion by McIvor, R. and Fink, R. P. We must challenge what we consider to be dubious statements in the above-mentioned article. Much of what is reported was published elsewhere over a year ago (i.e., in their reference: Chi, G., Fuerstenau, M.C., Brandt, R.C. and Ghosh, A., 1996, "Improved comminution efficiency through controlled blasting during mining," International Journal of Min¬eral Processing, Vol. 47, p. 93). There is nothing unusual or significant about a 10% or more difference in grindability between two materials of apparently similar origin and other attributes (such as chemical assays, hardness and specific gravity). Consider also that: • the materials came from different locations in the pit; • only two sets of four blastholes were considered per blast: • spatial orientation with respect to the face and other blastholes was also altered; • only two pairs of data were collected; • the impact of sampling error and bias, • both of which could be significant in this case; and • normal experimental error in parameter measurement and calculation. It is clearly inappropriate to draw any conclusions with regard to cause-and-effect relationships without first presenting a thorough error analysis. A substantial number of randomly selected test and control areas might provide meaningful statistical evidence of the claimed effect of the variables being studied. Even that appears doubtful, however, because Figures 3 and 4 show about as much variation in crushing energy for the two "regular" conditions vs. regular and altered conditions. On a separate, but also important issue, broad experience with autogenous/semiautogenous milling has shown that smaller or weaker feed material results in reduced tonnage. ? Reply Thank you for the opportunity to respond to the comments of Messrs. Mclvor ant Fink. The points raised are addressed in the order of presentation. As the commenters noted, there are parallels between this article and a previous manuscript. The reason for these complementary articles is that the audiences for the two publications are different, although there is obviously some overlap. We believe that the different audiences each profit from the technical aspects of the two manuscripts. We are not in agreement that a grindability difference of 10% is insignificant. The laboratory work is corroborated by data obtained at plant scale, which confirms that an increase in throughput of the same magnitude (between 5% and 10%) is achieved when the blasting pattern is modified, i.e., reduced from 9 to 8 m (29.5 to 26.2 ft). This increase in throughput translates into substantial power savings for ore grinding. No differences in appearance in the rock were noted between the two adjacent areas. Rock in both areas belonged to the same rock mass/block, which was quite homogeneous and without geological features in between that could create drastic differences in comminution characteristics. Given the resources, we would have sampled from all of the holes. Additional data would certainly have been desirable, as would have been additional funding to expand the study. Their comment, "spatial orientation with respect to the face and other blastholes was also altered," is not clear. Figure 1 does not show the initiation sequence. Without the initiation sequence, we do not understand how the commenters concluded that spatial orientation with respect to the face and other blastholes was altered. The commenters may be trying to make the point that the four-hole configurations with respect to the original bench face are not exactly the same. In fragmenting the

Jan 1, 1999

By N. Kuyucak

Uranium ores leached with sulphuric acid typically have poor dewatering properties. Applicability of controlled neutralization where gypsum precipitates as crystalline particles, improving dewatering properties of material was examined. Neutralized material was then dewatered using paste thickener to increase underflow density. The objectives are to maximize water recovery due to water scarcity and to produce suitable cemented paste fill material for optimizing underground ore recovery. Work was performed on acidic slurry samples collected after leaching but before the resin-in-pulp uranium recovery. Controlled neutralization greatly reduced volume of neutralization precipitates giving higher densities and improving the dewatering (filtration) properties. As a result it would be possible to increase the water recycled to the mill. Another benefit is that sulphate in the recycled water was reduced to saturation limit minimizing scaling of process equipment. Additional test work is needed; however, Unconfined Compressive Strength results imply that controlled neutralization increases the strength of paste fill and possibly offers opportunities towards a viable backfill option.

Jan 1, 2010

Dynamic permeability is a significant hydrologic condition associated with in-situ leaching at the Cyprus Casa Grande operations. Several factors contribute to changes in the permeability conditions. They are: 1) hydraulically induced fracture development, 2) geochemical changes during leaching in the rock matrix, and 3) changes in the relative degree of saturation of the deposit. Dynamic permeability conditions were evaluated using available pressure and flow rates from the 58 injection and recovery wells obtained over one year period. A finite element, 2-D hydrologic model called INVERT which is designed to estimate aquifer parameters under transient and steady state flow conditions was used for the investigation. The permeability conditions during 7 different steady state intervals throughout the one year time frame were determined. The results confirm that big changes in permeability occur as a function of time as well as a function of injection pressure condition.

Jan 1, 1991

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993

By JÖRG DEHNERT, PETER WINDISCH, Bernd Schönherrt, JENS STOPP

The Quick-Erect Stopping System (QESS) offers a new way of reducing the radon exposures of miners in Germany, especially during remediation work in old mines. The QESS is a light-weight, modular, and reusable construction kit of interlocking telescopic aluminum tubes, radon-proof foil, and expanding foam. It is designed to seal off radon-rich parts of galleries within only a few minutes. Originally, the QESS was developed to protect miners against radon exposures. Then, the QESS found the attention of several mine rescue teams at a German mining conference. The Student Mine Rescue of the Technical University Bergakademie Freiberg and the Wismut Mine Rescue carried out firstmine rescue drills in Freiberg and Schlema. Additionally, a mine rescue drill was carried out by the Front Range Mine Rescue in the Edgar Experimental Mine of the Colorado School of Mines. These drills helped to improve the systemand highlighted its potential for mine rescue operations. Now, the QESS is wellsuited for small-scale mining. The QESS can be used to seal off galleries in only a few minutes to both protect miners fromradon exposures and to support mine rescue operations. Moreover, the QESS was also successfully used in ventilation experiments.

Jul 23, 2020

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By Tim Neil, O&apos

Introduction On the banks of the Columbia River, about halfway between Seattle and Spokane, sits Wenatchee, WA. It calls itself "the apple capital of the world." And it has a gold mining history that dates back to the 1880s. It was just outside Wenatchee - three blocks outside, to be exact-that Asamera recently dedicated its $60 million Cannon underground gold mine. At full production, it is estimated the Cannon mine will yield between 5 and 5.6 t/a (160,000 and 180,000 oz per year) of gold. That would make Cannon the largest North American underground gold mine to be brought into production this year. Cannon should also be among the top 10 of all North American gold producers. Asamera officials project Cannon's operating costs at about $4.8019 ($150 per oz). At that rate, the mine should also be one of the lower cost and most profitable gold mining operations in North America. One reason for low operating costs is low electric power costs. The Cannon operation will be paying about 2.5 cents per kWh for hydroelectric power supplied by the Bonneville Power Authority. Proven and probable ore reserves at Cannon are in excess of 4.7 Mt (5.2 million st). Reserve grades average 7.29 g/t (0.21 oz per st) of gold in three ore zones, in order of discovery - B, B West, and B North. The ore bodies could have been mined by open-pit methods. But underground mining was chosen for environmental reasons. In addition, the rich B North ore body extends beneath a nearby horse stable and arena. The Cannon mine area comprises some 20 km2 (5000 acres) in Chelan County. The mine site is located at the 305 m (1000 ft) elevation in Dry Gulch at the base of the Cascade Mountains. The initial estimate of mine life for the Cannon operation is eight years, depending on gold prices. But Asamera officials believe the Wenatchee area has excellent potential for future gold discoveries. Asamera, Inc. of Calgary, Alberta, owns 51% of the Cannon property, through its wholly-owned Asamera Minerals (US). Breakwater Resources Ltd. of Vancouver, British Columbia owns 49% of the operation. The Cannon mine is named in honor of longtime Asamera, Inc. executive and current company director, geologist Donald G. Can¬non. It was he who first brought the Wenatchee property to Asamera's attention and urged the company to pursue it. Asamera is a major explorer and producer of oil and gas. Its Cannon operation is the largest and most significant to date in its mining division, according to Rob¬ert G. Welty. He is Asamera's chairman and chief executive officer. It should be noted there was an element of serendipity involved in Cannon's development. The development program be¬gan when geologist Cannon visited the Wenatchee area. He was visit¬ing old mining districts. He liked what he saw. The Cannon property was eventually optioned for ex¬ploration, including a modest drilling program.

Jan 12, 1985

By M. Baumann

Operating and maintaining the heavy equipment used in open-pit mining operations is an ongoing challenge for mines. Typical operations employ a combination of shovels, wheel loaders, and haul trucks to excavate and transport the material for further processing. As this is the first point of contact for the material after blasting, it is often a bottleneck of all downstream processes, thus, equipment uptime and efficiency is crucial. Automated systems for bucket tooth monitoring, payload measurement, proximity detection, and rock fragmentation analysis will be examined. The impact of these systems on operation safety, efficiency, and reliability, in real-world scenarios will be investigated. The process of managing all the above fleet of equipment in a mine can be streamlined by connecting the equipment monitoring systems to a central server. Using the central server, the distribution of this information can be automated to ensure that the right people see the data in a timely manner, improving both proactive and reactive responses to threats to safety and productivity.

Feb 23, 2014

By Anuradha Khetwal, Tala Tahernia

The estimation of TBM utilization rate can be problematic due to the uncertainty involved in the tunneling system reaction to various geology along the tunnel. Moreover, the impact of operational and management issues on TBM performance is unsettled. This includes the occurrence and duration of downtimes and the uniqueness of projects relative to the geology, machine type, backup system, site setup, crew experience, and operational restrictions imposed on the project by localities. The CSM2020 is a model based on discrete event simulation that predicts machine utilization for single or double shield TBM. This model was developed by the Earth Mechanics Institute (EMI) team, using the database of tunneling activities which was compiled based on field observation and measurements in pertinent projects. In the current study, CSM2020 was modified to simulate the workflow of slurry TBMs. The operating principle of slurry shield TBMs is different than open-mode TBMs. The model was verified by comparing results with a recently completed project in the United States. As a result, the model offers reliable utilization rate estimation in different types of TBM by implementing appropriate workflow.

Dec 1, 2022

By Mark Colwell

As per most other earth science engineering problems, the underground coal geotechnical environment and the way in which roof and rib support interacts with the rock mass are complex issues. While the problem should not be oversimplified (i.e., the dominant failure mechanisms or critical data input parameters should not be ignored), without question judicious simplification is at the heart of all good engineering design. Engineers play a vital role in supplying the world with solutions and products; however it is crucial that engineers make practical and readily useable contributions. One way to ensure this is to employ simplification in the engineering process.

By Winfield G. Wright, Philip L. Verplanck, Philip L. Hageman, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

Geological, hydrological, and geochemical information synthesized in a Geographical Information System (GIS) for water and rock surrounding South and Middle Forks of Mineral Creek, northwest of Silverton Colorado, was analyzed to distinguish between the natural and the mining-related sources of metals to dace waters in the watershed An important natural source of metals to surface water emanates from a porphyry molybdenum deposit south and upslope from the Middle Fork of Mineral Creek. Interaction of surface and ground water with fractured, altered rocks and permeable, Quatemay-age surficial deposits produces downstream water quality that does not meet current State of Colorado water quality standards for metals and pH. GIS site characterization and three-dimensional modeling distinguish surficial deposits as volumetrically substantial, significant sources of naturally occurring metals that strongly influence water quality and complicate ongoing mine-site mitigation efforts. Our findings indicate that regional hydrologic and geologic information needs to be evaluated before realistic water quality guidelines are established and mitigation recommendations are confidently implemented.

Jan 1, 2000

By Steven K. Ruggieri

Increased coal production on longwalls has brought with it higher levels of dust generation. Most U.S. longwall mining operators have difficulty complying with Federal dust standards, which are stricter than European standards. Longwall operators faced with a longwall that is "out of compliance" have implemented a variety of practices designed to reduce dust levels. Mining conditions and other important variables, however, can cause fluctuations in dust levels that may overshadow the performance of a new dust control technique. This can result in the continued use of an ineffective technique or lead to the abandonment of an effective dust control technique. No single technique can keep a longwall in compliance. Maintaining compliance requires a fundamental approach to dust control -- proper application and continued use of effective dust control techniques.

Jan 1, 1983

By J. R. Koehler

Yield pillar-based gate road designs oftentimes fail to provide mine operators with adequate ground control because of the unknowing misemployment of "critically" sized pillars. A "critical" pillar is one that is too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but is too small to support full abutment loads. To demonstrate the critical pillar concept, a field study of a tapering gate road was conducted by the U.S. Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 1 O.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1995

By A. T. Visser

The expansion of surface mining has led to the development of very large off-highway trucks currently capable of hauling payloads in excess of 290t. Mine haul roads have historically been designed empirically, relying heavily on local experience; the trend in increasing truck size will thus render the current pavement systems inadequate. Since truck haulage costs can account for 10%-50% of the total costs incurred by a surface mine, not only would the maintenance costs of existing roads of inadequate design increase, vehicle operating and maintenance costs would also increase prohibitively. There is thus a need for improved design technologies encompassing the construction and management techniques of mine haul roads, appropriate for the wheel loads of vehicles now in use. The aim of the paper is to present the different components of a mine haul road design and management system and to demonstrate the value of its application through case studies. The system has been applied at several South-African surface mines and distinct benefits have been derived. The improved structural design of a new road resulted in a 29% saving in construction costs and also provided better service, whilst the optimal selection and management of wearing-course materials provided better functionality at lower total transportation operating costs.

Jan 1, 1999

By A. S. Hall

Significant pyrite often does not dissolve in the Sobek (1978) nitric acid extraction; therefore, the standard conservative approach is to estimate pyrite using sulfur present in the sum of the nitric acid and residual sulfur fractions. Alunite, when present, appears as residual sulfur. Because alunite does not generate acidic effluents, overestimation of AGP can occur if all residual sulfur is assumed to be undigested pyrite. Evaluation of 16 samples from the Florida Canyon Mine revealed that petrographic examination coupled with a modification of the Sobek method to include a 6 hour hot (250°F) 'nitric acid extraction resulted in a more accurate estimation of AGP.

Jan 1, 1999

By Osvaldo A. Bascur

Standards and technology for bringing information to the desktop have greatly evolved in recent years. The benefits to be realized depend on how these new tools are embraced at the performer level. A key operating challenge is to ensure cooperative effort is geared towards the most efficient achievement of identified operating and corporate objectives. Presentation, application and database layers are emerging in successful client/server applications, the three-tier architecture.

Jan 1, 1996

By Robert D. Schmidt

The US Bureau of Mines is cooperating with Cyprus Mineral Park Mining Co., Columbia University, and the US Geological Survey in investigating the feasibility of applying in situ leach mining methods to fracture-hosted, supergene copper sulfide (chalcocite) ores. This paper presents the initial findings of mineralogical, hydrogeological, and geochemical characterization studies conducted at the Mineral Park mine, located in the Wallapai mining district of northern Arizona. A design for in situ leaching is proposed that would minimize the need for blasting prior to leaching, and would enable economical development of deep reserves at the Mineral Park mine. The in situ leaching design would also reduce the potential for long term acid rock drainage.

Jan 1, 1995

By H. B. Oblad

Coal/pyrite fines were froth floated in a laboratory cell to examine the rate of pyrite recovery during conventional coal flotation. The effects of collector, particle size and carbon to total sulfur ratio on the kinetics of recovery were investigated. These data coupled with microscopic examination suggest that miniscule amounts of coal that remain attached to the pyrite surface affect the rate of flotation of pyrite.

Jan 1, 1985