Search Documents

By Rosa Malena Fernandes Lima, Kerollan da Silva Ramos, Joyce de Assis Silva, Geriane Macedo Rocha

This study evaluated the effects of collector type amide-amine compared with those of conventional etheramine acetate (both cationic collectors) on the surface properties of quartz and hematite. An examination of certain properties of the reagents indicated that the new collector amide-amine has CMC (critical micelle concentration) and pKa values (100 mg/L and 8.2, respectively) significantly lower than those of etheramine (800 mg/L and 9.4, respectively). Microflotation tests showed that the recoveries of quartz with amide-amine in all the concentrations tested were higher than those with etheramine. This is attributed to its lower CMC and pKa values. The selectivity window between quartz and hematite flotation using amideamine was higher at pH 10.5 (approximately 80% for 5 mg/L). Therefore, the use of starch is not necessary in siliceous itabirite flotation by amide–amine collector. Zeta potential measurements and infrared spectra reveal that the adsorption of amide-amine collector on quartz surface occurs mainly by electrostatic attraction. Considering the better collectability of amide-amine for quartz flotation and lower adsorption affinity for hematite surface than etheramine, the amide-amine is a promising collector to be used in reversal iron ore flotation.

Jul 30, 2021

By Robert D. Harris

In 1958, the coal industry, through Bituminous Coal Research, Inc., and the electric utility industry, through the Edison Electric Institute and the Association of Edison Illuminating Companies, initiated a joint program to study coal pyrite and its removal as a means of lowering the sulfur content of steam coals. It was assumed that significant amounts of pyrite often remained in washed steam coal not because available systems for coal cleaning were inadequate, but because the pyrite was small and widely disseminated, During the first two years, samples of coal were examined petrographically to determine the size, association, and mode of occurrence of the pyrite in the raw coal and in the products of laboratory separation, Samples of coal were also pulverized in different equipment to determine how effectively pyrite was released by pulverization and if the mode of pulverization affected the liberation of pyrite. From these studies, the following tentative conclusions were made (1 ): 1. Much of the coal pyrite is within a 250-70 micron size range, and therefore is too small to be removed by conventional coal cleaning, but relatively large when compared to the size of coal as pulverized for combustion in large boilers. 2. The degree of pyrite liberation is mainly determined by the size of the product and not by the type of crusher. 3. For improved pyrite removal, the coal should be cleaned during or after pulverization at the power station.

Jan 1, 1965

By A. J. Richins, M. G. Nelson, R. Dunne

From the inception of flotation in the late 1800s, coarse particle recovery has been a challenge to practitioners. By the early 1900s, flotation processes included oil flotation, skin flotation, agglomeration flotation, and froth flotation, and for each there was a proliferation of flotation equipment. Ensuring good coarse particle recovery included desliming of the feed and proper conditioning were required. Froth flotation was at first used mainly to treat finer materials from grinding circuits. The maximum size for coarse particles was from 3.18 to 4.78 mm. In froth flotation, large particles with high specific gravity tend not to be recovered. Coal and minerals of low specific gravity and flaky minerals such as graphite, mica, and talc can be floated in larger sizes. In the early 1960s, the phosphate industry began using column cells to recover coarse particle by froth flotation, but early columns suffered from poor bubble generation and sanding at the flat base of the column. Recently, improved coarse particle recovery has been the object of new cell designs—the Eriez HydroFloat™, the Jord NovaCell™, the FLS coarseAir™ cell, and the Cidra P29 integrated system. The paper will follow the development of coarse particle flotation with a focus on the development, laboratory assessment, and operation of the new flotation equipment and technology designed to recover coarse particles.

Feb 22, 2026

By Jacob L. Brinkman, Catherine E. Johnson

Unmanned aerial vehicles (UAVs) are being explored by researchers to measure concentrations of gas emissions in situations where such measurements are otherwise extremely difficult to obtain, such as NO and NO2 (NOx) emissions from surface mine blasting. Recently, countries have imposed or are planning to impose surface blasting gas pollution regulations, which creates a need for an improved understanding of UAV-based gas measuring systems. The experiments detailed in this paper were performed to determine if airflow generated by the rotors, also known as downwash, unnaturally alters concentration measurements. Downwash turbulence could create locations of varying pressure, which could affect concentration. A UAV fitted with gas sensors was attached to a stand in a controlled environment containing a mixture of NOx. The gas sensor measuring points were placed at various distances on and from the UAV body to evaluate downwash effects on gas concentration. Results show that the presence of downwash turbulence causes no statistically significant changes to concentration measurements at any distance or direction from the UAV. Based on these results, it is possible to use a UAV-mounted gas monitor to measure concentrations without concern for downwash interference, provided the UAV and measuring point are entirely contained within the gas cloud.

May 20, 2021

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1983

By Robert S. Shoemaker

The development of a metallurgical project is a business venture rather than a technical exercise, and its real objective is to obtain the maximum return on investment consistent with the limitations imposed by company policy and the requirements of society. Demand for profits is the driving force for technical advances and naturally leads to improvements in processes, equipment and plant designs. In the mineral dressing field there have been virtually no new processes developed since the introduction of flotation, and the steady erosion of profits by inflation has been offset only by increasing equipment size. Unfortunately, in recent years, plant designers have not always utilized the largest equipment or the opportunities for functional and economic design presented by the development of larger equipment. Lower cost plants can be developed providing that unrealistic restraints arising from the prejudice of past practices are avoided. As an illustration of this premise, three different approaches were taken toward the design of a clearly delineated but hypothetical copper concentrator of 20, 000 tons per day capacity. While the same flowsheet was used in each case, designs were produced for a conventional plant, an alternate using the largest available equipment, and a third scheme utilizing large equipment and the most functional design which could be developed, including features derived from many plants in many different industries. Capital costs were developed for the three separate designs based on a location in the southwestern United States. Ancillary facilities were identical in each case and included a mine truck shop, a maintenance shop, a general office, and a nominal starter dam for tailings disposal within 5000 feet of the plant. Water supply within 1000 feet of the plant, and power furnished to the property boundary has been assumed in each case. The flowsheet of the three plants is shown in Figure 1 and represents the treatment of a typical sulfide copper ore by three- stage crushing followed by single-stage ball milling. Concentration is by flotation roughing and scavenging followed by regrinding of the concentrates and two stages of cleaning.

Jan 1, 1971

By Steven E. Mischler, Jay F. Colinet

The Mine Safety and Health Administration (MSHA) promulgated a rule in 2014 that required numerous changes in compliance dust sampling requirements for coal mine operators. Two key parts of this rule were the lowering of the respirable coal mine dust standard from 2.0 mg/m3 to 1.5 mg/m3 and requiring operators of underground coal mines to use a continuous personal dust monitor (CPDM) for compliance sampling. The CPDM currently approved for compliance sampling is equipped with a display that provides miners with in-shift information on their respirable dust exposure. The goal was to provide an indication of a potential overexposure and empower the miner and mine operator to implement changes in controls and/or operating practices to prevent an overexposure from occurring.

By Yun Bai, Sarah Wilson, Michael Salcher, Mark Trim

Over the last decade more than 62 miles (100 km) of civil transport tunnels were constructed in Sydney, Australia, using the sequential excavation method (SEM). The WestConnex motorway tunnels, each stage of which used over 20 roadheaders to excavate up to 40 tunnel headings, had numerous caverns up to 100 feet (30 m) wide and 82 feet (25 m) high. SEM tunnels in North America typically have far fewer active headings. This paper examines the differences in scope and risk allocation for construction phase services, including comparison of the Permit to Tunnel (PTT) process in Australia and the Required Excavation and Support process in North America.

Jun 23, 2024

Previous models describing the aggregation of polymer coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called ?active? sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1987

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the major disasters in coal mines, and it can have devastating effects on the normal mining and production activities of mines. This paper presents the field investigation, field measurement, data analysis, and formulation of fire-extinguishing measures conducted to extinguish the fire from a coal spontaneous combustion incident that occurred in a high-gas coal mine in China.

By George E. Edwards

Pacific Rim markets for export coal already represent a larger market than the total tonnage imported into the European Community countries and they will continue to expand. The largest importers will continue to be in the sector comprising Japan, Korea, Hong Kong and Tai- wan. It is likely that the total Pacific Rim markets will reach 206 m.t.p.a. by 1990 and 290 m.t.p.a. by 2000, with the major growth in steam coal demand. Australia has an efficient coal industry, represents a stable long term source of supply and is favourably situated geographically to continue to be the largest single supply source.

Jan 1, 1982

By P. Semberg, B. Bjorkman, C. Andersson

"In this study, the interaction between magnetite and the additive olivine was studied after oxidation as well as after isothermal reduction at temperatures in the 500º-1,300º C range. In the olivine sample, the forsteritic olivine particles react partly during the oxidation pretreatment to form magnesioferrite and vitreous silica along the particle corona. This breakdown of the olivine particles during oxidation liberates magnesium from the particles, which do not react until temperatures of above 1,150° C in reducing atmosphere. When the hematite in the sample is reduced, and when the temperature is high enough to allow solid-state diffusion at ~800º C, the magnesium of the magnesioferrite redistributes, so that the magnesium concentration approaches the same level throughout the iron oxide structure. For magnetite, this did not occur until 800° C. At 1,000° C, this magnesium reacts further with the silica in the glassy slag phase, which crystallizes into fayalitic olivine. At this temperature, the magnesium has diffused over distances of more than 600 µm from large olivine particles after 2 hrs reduction. From this point, the primary slag phase in the pellet, until melting, is solid fayalite. Upon reduction to metal, the metallization front concentrates the MgO in the remaining wustite, which can lead to MgO levels of up to 10 mole% locally. The melting point of the fayalite is raised from 1,145º C to a melting range of 1,238-1,264º C due to the MgO increase, as estimated based on phase diagrams, which were adapted to the pellets tested. Much of the olivine that remained unaltered in the oxidation process will be encapsulated by iron before the particles begin to dissolve in reducing conditions and, therefore, plays no role in the reduction before final melting of the particles occurs.IntroductionEnvironmental concerns have placed increasing pressure on the CO2-intensive iron and steel industries to further optimize operation toward higher productivity and more efficient use of reducing agents. At the same time, high demand for iron ore has caused new iron ores with lower grades and more complex chemistries to be taken into production. In Scandinavia, the main iron-bearing material is magnetite-based pellets with olivine, which allow operation with very low slag volumes and, hence, lower fuel rate ( Slagnes and Sundqvist Ökvist, 2008; Hallin et al., 1994). Both the MgO and SiO2 of the olivine, as well as the elements of the gangue of the ore, i.e., Si, Mg, Ca, Al and alkali, interact with the iron oxides to give the finished pellet product its final properties in the blast furnace. Tailoring the additive mix to be used for a certain iron ore for optimal product properties, therefore, requires detailed knowledge of the mechanisms by which these elements dissolve and react in the pellet."

Jan 1, 2015

By D. S. Flett

Abstract. The commercial importance of hydroxyoximes as extractants for copper has given impetus to basic studies on the chemistry of metal extraction by these compounds. The discovery of accelerator compounds which produce catalytic effects on hydroxyoxime extraction rates has led to mechanistic studies of these rate processes. While these studies have highlighted the importance of interfacial chemical reactions in the extraction process, it is not yet possible to unambiguously describe the mechanisms of metal extraction in these systems or the associated catalytic effects. This paper reviews progress in understanding the mechanism of metal extraction by hydroxyoximes.

Jan 1, 1979

By Deborah Shields

Aggregate is an essential input to every economy, so governments need to ensure a sustainable supply of these resources through planning. There is also a need to shift from a linear economy to a more circular one, in which wastes are recycled rather than landfilled, so as to increase eco-efficiency. The purpose of the Sustainable Aggregates Planning in South East Europe (SNAP-SEE, SEE/D/0167/2.4/X) project is to develop a Toolbox for Aggregates Planning to assist governments and stakeholders in national, regional, primary and secondary, aggregates planning in southeast European countries. The Toolbox comprises documents on stakeholder consultation, data and analysis methodologies, a vision of best practices in aggregates planning and how to build an aggregates plan. The Toolbox will also support ongoing efforts to enhance minerals policy in the European Union (EU) as called for by the European Innovation Partnership on Raw Materials. Industrialized and developing nations see long-term and continued economic growth as essential to the well-being

By Todd Minoski, Matthew McElhinney, Morgan Sears, Craig Compton

In an effort to advance the science underlying ground control engineering, researchers with the National Institute for Occupational Safety and Health (NIOSH) are frequently involved in field studies at collaborating mines. Often, these field studies involve visiting the mine site, instrumentation installation, and data acquisition. Each of these aspects involve potential risks to NIOSH employees. As an organization whose mission it is to promote the health and safety of mine workers, the health and safety of our workforce is paramount. This paper provides documentation of the best practices followed by NIOSH employees who are tasked with visiting and conducting work at underground and surface mines. This includes Mine Safety and Health Administration (MSHA) approved training, mine site specific training, and hazards associated with all aspects of mining that could be encountered by the employee. Additionally, this paper details best practices associated specifically with instrumentation installation including the mitigation of hazards associated with the proper equipment handling, drilling, and the mine environment. The information showcased in this paper can be used as considerations for industry practitioners such as mine operators, consultants, and academic researchers engaged in the installation of instrumentation in the field. Furthermore, the best practices detailed in this paper can be used as a foundation for agreements made between mine operators and researchers to ensure safety procedures will be followed while on mine property. This will result in enhanced safety of both researchers involved in field studies as well as mine employees tasked with assisting and accompanying those researchers.

Feb 1, 2024

By S. E. Younis

The mining industry is currently looking to better understand, anticipate, and be able to mitigate business and operational risks in order to deliver the rewards of risk taking, and to minimize the frequency and impact of risk on the downside. Assessing risk works from the premise that the identification and management of existing risks can be very challenging, especially when threats are not easy to detect, the likelihood of occurrence is difficult to gauge, and/or the consequences are uncertain. Some approach this as a ?check the box? task, even though fire and safety incidents continue to occur and investigations often find the hazard analyses did not properly identify the cause or consequence. You cannot engineer protective designs and safeguards for causes and consequences that have not been identified appropriately. For the mining industry, risk management is an important tool for making critical decisions and, in some cases, meeting regulatory requirements. Providing high-quality documentation that meets both regulatory and corporate requirements is critical for maintaining safe, uninterrupted mining operations. Risk management is a five-part process: 1. Identify the hazards and their causes, 2. Determine the hazard consequences, 3. Calculate the frequency of occurrence, 4. Quantify the risk associated with the system, process, or procedure, and 5. Provide feasible solutions for the risks

Jan 1, 2012

By B. T. Lusk, Q. Q. Huang, R. Q. Honaker, K. A. Perry

Rock dust is applied in underground coal mines to prevent the propagation of coal dust explosions. It is applied either dry or wet. Both methods have advantages and disadvantages, but the formation of caked rock dust particles is cited as a significant concern for wet applications. We conducted a study to evaluate the effect of modifying the rock dust particle surfaces to repel water and each other by the addition of oleic acid and sodium oleate. At a sodium oleate dosage of 1 kg/t, a contact angle of 112o was measured, indicating strong surface hydrophobicity and thus the ability to repel water. Fourier transform infrared spectroscopy (FTIR) studies indicated a chemisorption mechanism, which is necessary for long-term stability of the surface modification. The dispersibility of the modified rock dust samples was elevated by the application of both oleic acid and sodium oleate, thereby indicating a significant reduction or elimination of the detrimental effect of caking. Tests in an explosion chamber showed an 82.8 percent reduction in the dust explosion potential relative to untreated rock test applied by the wet technique.

Jan 1, 2015

By Robert J. Ramsey, N. Finkelstein, Robert D. Jeppson

Introduction The Utah Copper Division of Kennecott Copper Corporation will present its contribution to the A. M. Gaudin Flotation Symposium in four parts. The first two segments will discuss briefly the historical development of the Utah Copper Division and describe the ore body. The third segment will review the facilities and operating procedures for the Utah Copper Division's newest plant, the Bonneville Concentrator. The fourth segment describes flotation process circuitry, including molybdenite recovery procedures, at the Arthur and Magna concentrators. (The Bonneville concentrator is a crushing and grinding unit and does not have its own flotation plant). 1. Historical Development Progress through change has been the key to the successful operation of the Utah Copper Division for more than 70 years. As the original low-grade copper operation, the pressures to remain competitive and profitable have dictated the timing and extent of each change. Much of the change has occurred through technological and economic advancements in the area of ore concentration. The Utah Copper Division of Kennecott Copper Corporation had its origin June 4, 1903, when the Utah Copper Company was organized. The initial mill of 300 tpd (tons per day) capacity was built at Copperton a few miles below the present Bingham Canyon mine site. From 1904 to 1910, the Copperton mill was expanded to a capacity of 1,000 tpd, and all of the known apparatus for gravity concentration were evaluated.

Jan 1, 1976

By Jeremy Stone, Yiming Sun, John Stolz

The Courthouse Commons Tunnel facilitates the secure transfer of inmates between the County Jail and State Courthouse across a city block in downtown San Diego, California. This shallow tunnel was excavated using the Sequential Excavation Method in soft ground. It passes under 8- and 10-story buildings with a foundation cover of 6 feet, and crosses the active San Diego Fault with a design offset displacement of 18 inches. In this paper, key design challenges of tunnel construction are presented: limiting building settlements without using underpinning of building foundations and incorporating an oversized seismic section with seismic joints and crushable backfill

Dec 1, 2022

By VIVEK KUMAR HIMANSHU, M. P. Roy, P. K. Singh, A. K. Mishra, RAVI SHANKAR

Blasting with the aim to reduce oversize boulders in underground has many hurdles due to limited accessibilities and poor site conditions. Optimized drilling and blasting parameters can help to achieve this objective. The major challenges of the blast designers lie within deciding blast geometry, namely drill hole diameter, burden, and spacing. The general approaches covered worldwide to determine burden-spacing are based on various rules of thumb, which are based on previous experiences of blasts and the associated outcomes. However, many parameters influencing optimum burden-spacing to achieve desired fragment size are site specific. Sometimes drill geometry is decided based on associated blasting hazards rather than rock fragmentation. The Kuz–Ram model is a worldwide accepted rock fragmentation predictor. The parameters associated with this predictor also include burden-spacing for a blast. Back calculation of burden-spacing from the Kuz–Ram model can be used to achieve desired fragment size. This paper deals with burden-spacing determination by using an empirical approach for the underground stope ring blasting.

Jan 4, 2020