Search Documents

By D. I. Smith

Constructing tunnels in congested urban areas requires tunnels to be placed closer together and with less cover than was previously necessary. Contract CQ031 of New York?s East Side Access project will construct four six-meter diameter bored tunnels in a three-up one-down ?T? configuration, with less than three meters of soil between the tunnels. Mixed-face rock and glacial till conditions with a high ground water table will be encountered under active railroad yards. The tunnels will also pass beneath the busiest railroad interlocking in North America with cover as shallow as three meters. This paper discusses the challenges of designing segmentally lined tunnels for these conditions.

Jan 1, 2008

By Vinícius Resende Domingues, André Pacheco de Assis, Bernardo Cascão Pires e Albuquerque

"The increasing demand for underground works in urban centers, and in particular the need to build undercrossing tunnels, requires constant evolution in building techniques in order to achieve success and safety. In the case of Brasilia, capital of Brazil, in order to preserve an important avenue (Eixo Monumental), where are located many historical monuments, the construction of a tunnel was envisioned as an option to interconnect the National Stadium (on one side of the avenue) to the Convention Center Ulysses Guimarães (on the other side). The excavation design is comprised of a coverage smaller than one diameter, height of 7.5 m, width of 9.0 m and length of 25 m. In order to enable a negligible influence on the avenue’s usage, the structure is designed as a portico system composed of pipe canopy. In this context, this study presents the portico analytical solution computed with the aid of the software Mathematica and a numerical solution using the software ABAQUS. INTRODUCTION Undercrossing tunnels are increasingly common in urban centers as alternative roads or as access to underground works of large dimensions (stations and parking lots). The geomechanical conditions of the soil mass, not always favorable, and the low distance between tunnel’s ceiling and the surface require intense treatment of the soil massif and execution of a rigid support system. The importance of the road just above the undercrossing tunnel emphasizes the need for a highly competent monitoring system because existing structures require minimum allowable displacement and do not allow the interruption of traffic. The soils that are excavated for the construction of undercrossing tunnels are composed, in most cases, of layers of fill and / or soft soil or weak rock, showing stability problems when subjected to tunneling operations. The combination of low coverage and week ground is solved by soil improvement techniques and strengthening of the excavated cross-section with further advance with the so-called New Austrian Tunneling Method (NATM). Another option is to build structural frames that support the surface. In this research, and based on the context of a case study, we propose the study of the construction technique comprising a portico structure composed of pipe canopy. For this paper, the technical standards used are the Brazilian ones as the case study refers to this country."

Jan 1, 2016

Following a disaster in a mine, it is important to understand the state of the mine damage immediately with limited information. Computational fluid dynamics can be used to simulate and ascertain information about the state of ventilation controls inside a mine. This paper describes a simulation of tracer gas distribution in an experimental mine with the ventilation controls in various states. Tracer gas measurements were taken in the lab experimental apparatus, and used to validate the numerical model. The distribution of the tracer gas, together with the ventilation status, was analyzed to understand how the damage to the ventilation system related to the distribution of tracer gases. This study will be used in future research in real mine measurements to compare collected and simulated profiles and determine whether damage to the ventilation system has been incurred during an emergency situation, the nature of the damage and the general location of the damage.

Jan 1, 2011

By R. Gunda

Due to the rapidly increasing production rates and deepening of mine working areas, there is a drastic rise in the number of thermal issues to be addressed for maintaining a safe mine environment. As high temperatures and humidity in underground mines could affect the health and performance of workers, and ultimately the production rate, it is necessary to provide a properly controlled safe environment. The backfilling of stopes in metal, non-metal mines results in different thermophysical properties for the hanging, side and foot walls, modeling of which is not provided by any existing mine climate simulation software. This paper presents the modeling of such a single stope using the MULTIFLUX (MF) software, developed at University of Nevada, Reno. A special case is presented in this paper, where a case study from the Homestake mine in the US with a drift and ramp connected to a stope with high Virgin Rock Temperature (VRT) and various spot heat sources is modeled in MULTIFLUX and CLIMSIM, and the results are compared against each other. Another case is presented in which the stope of the previous cases is modeled with walls, each having a different set of thermophysical properties. These results are compared with the former results to analyze the effect of anisotropic properties.

Jan 1, 2011

By K. Hanumantha Rao, A. Nayak, K. S. Narasimhan, S. N. Mahapatra

B.A. Hancock It is not at all surprising that causticized potato and potato derived amylopectin starch solutions performed much better than their parent starches. Some preparation is required to rupture the starch granules to effect the polymeric adsorption and interparticle bridging necessary for selective flocculation. In laboratory work comparing the deslime performance of causticized and autoclave cooked laboratory corn starch solution preparations, it was found that higher deslime weight rejections, with attendant proportionally greater iron unit losses, occurred with the causticized starch. These results may be specific to the ore involved but they do suggest that cooking and causticizing cause different starch granule rupture and/or starch breakdown, which have an effect on desliming response. I calculated from the data in the article that the slimes product grades were high - 24.3% and 20.3% Fe when 53.7% and 54.5% Fe concentrate products were obtained, respectively, in Table 4, and 21% Fe with a 62.6% Fe concentrate in Table 5 - using the natural tailings sample, which had a head of 34.3% Fe. It may be advisable for the authors to consider different starch preparations in future investigations. The combination of upgrading and selectivity results presented in Table 4 are not as good as the authors suggest. The authors' claim that a system has been developed to produce saleable concentrates from the Kudremukh tailings is quite disconcerting. There are many hurdles yet to be crossed before commercial application of selective flocculation becomes possible because differences between the very small-scale laboratory tests conducted and commercial application are rather large. Among the many differences are varying circuit feed grades that will occur from use of tailings, the apparent face that much lower tailings grades will be encountered in practice (it is much easier to achieve a high concentrate grade with reasonable recoveries using 34.3% Fe tailings as in the study rather than 25.3% Fe tailings grades that the plant apparently averages), the hydraulic nature of the thickeners used in operations compared to the static system used in laboratory tests, the different size distributions that will be obtained from a plant closed grinding-classification circuit, and differences in water used in a plant operation and the laboratory. The authors wrote that it was necessary to overgrind to be sure that the coarse gangue would not settle with the iron oxide floccules. This situation is likely to be exaggerated in commercial operations where it is assumed cyclones would be used for classification. Because cyclone classification is greatly influenced by particle densities, there will probably be an even greater difference in size between the iron and gangue particles in the plant, which would make the gangue slightly coarser still in relation to the iron. This would make the selective flocculation-desliming separations using the procedure employed by the authors even more difficult and, using the dispersant system the authors employed, greater overgrinding would be required. To grind finer to minimize the coarse gangue in the flocculated iron oxides is quite inefficient and appears not to broach the problem. The actual problem appears to be insufficient dispersion of the ground pulp. In this situation, addition of a dispersant would likely be required to attain a sufficiently high pulp dispersion level to efficiently effect a selective flocculation-desliming separation. Although the very coarse particles would still have a tendency to settle with the floccules, it probably would be found unnecessary to overgrind as much as indicated. Use of an optimum combination of dispersant and pH modifying reagents may also significantly improve the selectivity of desliming. Additionally, although it is possible that sufficient dispersion may be obtained by pH control alone in some situations, it is quite probable that added dispersity was obtained in the reported work from using distilled water. It is research experience that distilled water enhances dispersion. In commercial operations it may not be expected that sufficient dispersion will be obtained by pH control alone, unless the water used in the process is by nature quite dispersive. Overall, a change in the Kudremukh tailings dispersant scheme appears necessary where a dispersant is used in conjunction with a pH modifying reagent. With this change, different dispersion-flocculation responses will result that would have to be further evaluated. Therefore, it is still an open question whether an efficient and effective selective flocculation separation using Kudremukh tailings may be obtained that will produce saleable concentrates.

Jan 9, 1986

By R. D. Hagni, P. A. Shivdasan

Cathodoluminescence microscopy (CLM) is uniquely applicable to the study of carbonatite-related fluorspar ore deposits. The mineralogy of the carbonatites, sodic and potassic fenites, marbles, quartzites, and fluorite ores are readily determined and characterized. Calcite, dolomite, apatite, fluorite were deposited dominantly under high temperature conditions and they exhibit strong cathodoluminescence (CL). Three types of carbonatites have been recognized at the Okorusu, Namibia carbonatite complex and fluorspar mines by field mapping and laboratory CLM. The main carbonatite intrusion is fine grained and consists mainly of calcite. A later phase of pegmatitic carbonatite consists of calcite, magnetite, Fe-rich pyroxene, apatite, and pyrochlore. Pyroxene carbonatites were recognized mainly through their study by CLM.

Jan 1, 2001

By D Beahm

Introduction The Energy Metals Corporation (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin including the JAB Property, one of several potential properties being planned for development as a satellite facility to the greater Antelope Uranium Project. A National Instrument 43-101 Technical Report has been completed for the JAB property. This report estimates total measured and indicated mineral resources on the property totaling 3,555,022 pounds U3O8 contained in 2,400,875 tons at an average grade of 0.073 % U3O8 at a .25 GT cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB Property is located in Sections 13, 14, 15, 16, 21, 22, and 23, Township 26 North, Range 94 West, approximately Latitude 42o 14’ North and Longitude 108o 00’ West (Figure 1, Location Map). This property consists of unpatented mining lode claims and Wyoming State mineral leases comprising approximately 2,100 acres.

Jan 1, 2007

By C. Allen

Vale Inco Ltd. is trialing several energy conservation initiatives in an effort to minimize costs and reduce green house gas emissions. The Ventilation on Demand (VOD) concept is a major project being carried out in various phases at Vale Inco mines. Due to the complex nature of a dynamic VOD system, Vale Inco is taking a systematic approach of testing VOD system components with milestone evaluations of each project. Coleman Mine was selected to pilot test the functionality and robustness of automated louvers in the underground environment; with the goal of optimizing mine airflow such that ventilation would be available for developing a new ore body. This project involved installing automated louvers in the exhaust raises; and installing variable frequency drive (VFD) starters on auxiliary supply fans. Because the VOD project created efficient utilization of the ventilation air in the 153 OB, the 170 OB is currently being developed without increasing the total fresh air into the mine. This paper describes the louver system component of VOD as applied at the mine.

Jan 1, 2009

By Robert L. Hautala

In 1978, Congress established a series of mineral institutes for a limited time to assist financially in mineral industry education and research. Later, education and research were separated, establishing generic institutes for specialized research that transferred the former research budget from the base mineral institutes program. One of the generic institutes is the Mine Systems Design and Ground Control (MSDGC). It provides for research funding specifically for mining. Other parallel generic institutes were established in pyrometallurgy, comminution, waste management, etc. MSDGC was established at Virginia Polytechnic Institute and State University(VPI). The founding group included the University of Alabama, University of Kentucky, University of Nevada Reno, University of Idaho and University of Alaska reporting through VPI to the US Bureau of Mines (USBM) and Congress. Other universities also participated on an ad hoc basis.

Jan 1, 1996

By M. Javier

Defining the concept of sustainability is an important step for industry and society. It is necessary in order to clarify what it means when debunking the many misinterpretations pervasive in different levels of anthropogenic activities. Essentially, the extractive industry has a harvest of differences. Mining involves the extraction of natural resources which are finite, exhaustible, non-renewable, unsustainable, and pay only once. It is remarkable that the definition of sustainability that we will shortly arrive at has totally different characteristics from the definition accepted throughout society. We categorize nature as having its own destiny which is controlled by its own rules and principles and its own society, and is part of nature; therefore, society depends on nature and not vice versa as the initial focus. To society there are no conditions to humanize nature but only respect nature?s rules. It was a challenge to find simplicity for this task not only for the definition but also for the explanation of this concept specifically, to answer the question, ?what is the true meaning of sustainability?? Finally, we are also able through this definition to provide fuel for wide discussions and stimulate critical thinking to improve such a concept. As a result, we present this definition as the tool for society today and for future generations.

Jan 1, 2012

By M. Z. A. Bakar

To investigate the differences in the radial drag pick cutting performance in dry and saturated sandstone, a suite of linear rock cutting test was performed using linear rock cutting machine (LRCM). Experimental results of 50 data passes, incorporating 350 data cuts were used to compute cutting, normal and side forces required for determination of other performance related parameters. Although the forces required to cut the dry and saturated rock were in congruence for most of the spacing and depths of cut combinations; but the overall averaged cutting and normal forces for saturated rock cutting were found to be 9.9% and 9.4% respectively higher than the dry rock cutting. The increase in the overall averaged forces was attributed to strength variability of one of the saturated block affecting the overall forces. The side forces experienced a negligible drop in saturated rock cutting. An increase of 28% and 9% in the actual and nominal specific energy values respectively was also recorded when cutting saturated rock as compared to the dry rock cutting. The increase in saturated rock specific energy is attributed to production of large amount of fines and few large sized chips directly contributing towards increase in specific energy. The optimum s/d ratio for dry rock tests was found to lie between 6 and 8 whereas for saturated rock cuts this value lied between 5 and 9.

Jan 1, 2012

By Liming Yuan, John C. Edwards, Gene F. Friel, Robert A. Franks

Diesel fuel fire experiments were conducted in NIOSH’s Pittsburgh Research Laboratory’s (PRL) Safety Research Coal Mine (SRCM) to determine the critical air velocity for preventing smoke rollback. Such information is necessary for the preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 kW to 300 kW depending upon the fuel tray area. Airflow in the 2 m high and 2.9 m wide coal mine entry was regulated during the course of each experiment; measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor; and recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light obscuration monitors, ionization smoke sensors, and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics (CFD) fire dynamics simulator.

Jan 1, 2005

By J. P. Brady

A major spontaneous combustion incident occurred in the sealed goaf of the SL3 Panel; Southland Colliery in 2003 resulting in the loss of a longwall and sealing of the mine. The most important issue for the new owners, Yancoal Australia Pty. Ltd, was to effectively manage the atmosphere in the fire affected sealed area. This atmosphere comprised of flammable gases, the products of combustion and excessive levels of oxygen due to pressure differentials across the panel isolation seals with a potential ignition source associated with the residual spontaneous combustion event. The challenges were met in the first instance by the erection of pressure balance chambers with limited success. The problem was not solved until the pressure chambers were pressurized using a Floxal Nitrogen Plant supplied by Air Liquide Australia. Given the success of this approach on a small scale, a higher capacity Air Liquide Floxal Unit was acquired to manage spontaneous combustion at the recommencement of longwall mining operations. This provided the ability to pressurize pressure chambers that were installed in the Maingate Seals behind the face of the adjacent Longwall Block effectively preventing the ingress of oxygen and permitting the goaf to self inert in a reasonable time period. This paper summarizes a new proactive method of mitigating the risks associated with active and sealed goaves. Proactive management of these areas using low flow nitrogen into pressure chambers to maintain a positive pressure has eliminated typical reliance in explosion proof or explosion resistance seals as the primary control.

Jan 1, 2009

By R. M. Cox

The ground forces generated by a properly installed and tensioned mine roof truss assembly can provide permanent mine roof support, even in severe ground conditions, either by direct suspension of the rock loads within the potential failure zone above the mine opening or indirect reinforcement of the natural rock arch that tends to form within the immediate mine roof. Notable advancements in mine roof truss support systems hardware and design technology have occurred since the introduction of the in situ mine roof truss concept for permanent mine roof support in 1966. The systematic installation of mine roof truss support systems has proven to be a very effective method of mine roof control room and pillar mines under a wide variety of ground conditions, even in areas otherwise considered unmineable because of severe roof control problems. Properly designed mine roof truss systems have also been used for permanent support of mine slopes and haulage tunnels.

Jan 1, 2002

By K. Hopperstead

Ventilation planning in trackless metal mining is often taken for granted. This paper highlights the trials of planning and executing the ventilation design for Bog Zone at the Lisheen Mine. Ventilation planning for Bog Zone started at the feasibility study stage in 2003; subsequent design changes continued until 2006. In August 2006, the development of the Bog Zone ore body was accelerated through the use of contractors; in addition, the Lisheen equipment fleet was revised based on a larger load and haul fleet. As a result, the circuit was reviewed in terms of changes in design conditions and best practices. This review resulted in a 40% increase of total airflow required to mine Bog Zone. Resources utilized to design the circuit include: external review, computer modeling, and in-house Lisheen planning and operational staff review. The final ventilation design configuration was adopted in 2007, after modeling and evaluating 30 different scenarios, resulting in a better distribution of airflow, optimized secondary escape way, reduced contaminants, and a total power reduction. The value of investment in computer modeling of primary ventilation circuit and planning for staged implementation should never be underestimated.

Jan 1, 2009

By S. Constantinides

Over the past 100 years we have witnessed a revolution in permanent magnetic materials. Prior to 1932 electrical machinery depended upon steels for both the soft and the permanent magnet structures. Because permanent magnet steels were easily demagnetized, motors, generators, loudspeakers and similar devices often used the interaction between two electromagnets. Motors and generators were mostly of the induction type, depending for function upon induced fields. The discovery of Alnico in 1931 and its rapid commercialization presaged an expansion of the industrial revolution and today, permanent magnet structures are widely utilized. [ ] DEVELOPMENT OF PERMANENT MAGNETS Act 1: Early Days of Permanent Magnets Alnico, which stands for aluminum, nickel and cobalt, is a family of alloys with similar structure and processing requirements. Additional elements, such as copper and titanium, are present in minor amounts to optimize magnetic properties. Alnico is known by many trade names around the world including Alcomax, Hycomax, Ticonal, Nipermag, Koerzit, Oerstit, Nialco, etc(1,2,3). In addition to the generic name ?alnico?, it is usually appended with a number representing the magnetic grade.

Jan 1, 2011

By M. Mikhaylenko

The most common methods of processing of uranium ores is sulfuric or carbonate leaching with conversion of hexavalent uranium to uranyl carbonate or sulfate anionic complexes followed by sorption of the later by strong base anion (SBA) exchange resins. It is known that chloride anion has high affinity for SBA resins so that it depresses sorption of anionic complexes of uranyl. Application of the SBA resins becomes impractical for recovery of uranium when chloride concentration in pregnant leach solution exceeds 3-5 g/l [1-3].

Jan 1, 2012

By J. L. Carr

Continuous mining machines are extensively used in the underground coal mining industry. These machines are typically remote-controlled, and severe injuries and fatalities occur every year when a miner is struck or pinned by the machine. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Researchers at the National Institute for Occupational Safety and Health (NIOSH)have developed the Intelligent Proximity Detection (iPD) system to provide enhanced protection while minimizing false alarms. The iPD system uses a set of pre-defined rules to determine which machine motions are safe and which would present a potential hazard, and automatically disables only the potentially hazardous motions. This system has been installed and tested on a Joy 14CM continuous mining machine at the NIOSH Office of Mine Safety and Health Research in Pittsburgh. Under laboratory conditions, the achievable accuracy and performance of the iPD system has been quantified with respect to a number of variables including position of the conveyor boom, presence of the machine?s trailing cable, and orientation of the miner-wearable component. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

By Steve Kral

The timing was right for SME to celebrate its 50th anniversary in February as a member society of AIME. The mining industry is in the midst of a commodities boom that appears to have legs. Not only is the demand for metals, construction materials and the like increasing in developing nations, but developed nations have also seen the demand for those materials increase at impressive rates. So, in addition to networking and seeing old friends, attendees at the SME Annual Meeting and Exhibit in Denver, CO. Feb. 25-28, had several reasons to enjoy the week — a healthy industry and their society’s landmark anniversary. This annual meeting was held jointly with the Colorado Mining Association’s (CMA) 109th National Western Mining Conference.

Jan 1, 2007

Your assessment of the minerals business. I would first like to express our profound sadness and sincere condolences to the families of the miners who lost their lives in recent mine mishaps particularly in West Virginia, and other locations. Any loss is unacceptable. It is time to review and, if required, re-establish a rigorous health and safety agenda in the mines. It must involve a review of health and safety regulations. And innovative training methods for sensing, awareness and mitigation of health and safety hazards must be developed. As far as the minerals business is concerned, I am excited about the outlook for mining. Over the last 20 years, global demand for minerals has closely mirrored the growth of the gross domestic product. Minerals re-main a major part of the world’s economic foundation. And that will continue to be the case. It is no surprise that the fortunes of the mining industry rise and fall with general economic trends. Globally, mining has been strong — thanks to the explosive economic growth in Asia. The U.S. mining industry has performed reasonably well, with notable strength in the metals, coal and construction and aggregate areas and with some softness in the industrial minerals sector.

Jan 1, 2006