Search Documents

By Ralph D. Daley, Kevin E. Redinger

The production of coal/water fuel (CWF), a highly loaded mixture of finely ground coal, water, and chemical additives, presents a unique opportunity for significant ash and sulfur reduction through physical coal cleaning. Froth flotation can be integrated with the staged, wet, fine grinding inherent in the CWF production process. A laboratory scale research program was conducted to demonstrate the feasibility of a flexible, integrated coal cleaning/CWF process flowsheet. Performance of the conceptual flowsheet was examined for two coals of CWF commercial interest, Upper Freeport and Pittsburgh seam coals, from central and southwestern Pennsylvania, respectively. Several multi-stage coal flotation and reverse flotation circuits were evaluated. CWF was produced from the cleaned coal in each case at similar solids loadings and viscosities as observed for the raw coal. However, the ash loading and SO2 emission potential for each CWF had been significantly reduced.

Jan 1, 1988

By H. Cho, P. T. Luckie

A study was undertaken to investigate the liberation behavior of coal macerals through size reduction and density separation. It was seen that the liberation of coal macerals could be achieved by size reduction, allowing selective separation of coal organic components. However, the degree of liberation was dependent upon the comminution history. Even for the same fineness, the extent of liberation might not be the same depending on how the material was generated. The liberation of coal macerals was analyzed by examining the liberation index. It was seen that, although comminution produced fine particles enriched in inertinite (primarily fusinite and semifusinite), these particles were less liberated than coarser particles. However, the liberation of macerals increased when all the feed was ground to a finer size.

Jan 1, 1999

By B. Bringhurst, J. J. McClelland

A filter consisting of a synthetic fibrous material has been determined to be a viable alternative to the wire mesh panels currently used in irrigated filter dust collection systems. An extensive laboratory investigation of the material showed that it removed a higher percentage of both respirable coal and quartz dust from the air entering a collector than did the flat and pleated wire mesh panel designs. This improvement in dust collection efficiency reduced the amount of coal and quartz dust discharged from the collector exhaust by approximately 44%. Since continued exposure to excessive levels (>5%) of respirable quartz dust presents a severe health hazard, this alternative filter medium could be of use to those mines required to comply with more stringent dust standards due to quartz.

Jan 1, 1992

By L. J. Prosser, A. T. Iannacchione

From 1991 through 1995, 44 miners out of a total workforce of less than 2,000 were fatally injured in the stone industry. Of these, 12 occurred at underground mining operations with nine deaths resulting from roof or rib falls. A safer environment can be achieved by evaluating the nature of the hazardous ground and by developing more efficient and effective ground-control strategies. Roof and rib conditions were observed and assessed in 33 underground stone mines in Illinois, Indiana, Kentucky, Maryland, Missouri, Pennsylvania and West Virginia (Fig. 1). Hazard assessment indicated that the ground failures that occurred under moderate to substantial overburden, i.e., >30 m (100 ft), were caused by stress concentrations and geologic structures. Ground failures near the surface are caused by solution (water) processes. Selection of the mining horizon and mine-layout decisions

Jan 1, 1999

By M. Li, J. D. Miller

Recently water insoluble alcoholic solutions of alkyl hydroxamic acid collectors have been shown to be particularly effective in the flotation of coarse feed material sampled from phosphate operations in Florida, North Carolina and Utah (Miller et al., 2000). The experimental results indicate that high separation efficiencies can be achieved in single stage flotation with these new collectors. In some cases the concentrate grade reached 34% P2O5 with 93% recovery from single stage bench scale flotation experiments. Critical aspects of the composition and structure of these new collectors are discussed with respect to their effectiveness in phosphate flotation. The wetting characteristics at fluorapatite, francolite, dolomite and quartz surfaces are being investigated with the new collector. Finally, other surface chemistry considerations in the development of these new collectors for phosphate flotation are discussed.

Jan 1, 2002

By Robert J. Wise, Mark Alspaugh

Underground longwall coal mines depend on conveyor haulage to transport large volumes of coal from the longwall face conveyor to the mine portal. In the last few years, the need for longer and larger longwall panel conveyors has become very significant. In order to keep conveyor equipment to a minimum and still transport higher tonnages over longer lengths, intermediate drive technology has been developed. The use of DC motors and controls in conjunction with load sharing techniques have a1 so proven effective. A case study of a new longwall panel conveyor at Utah Fuel's Skyline Mine incorporating these design techniques will be presented.

Jan 1, 1993

By Michael J. Martinson, John R. Larsen, J. Warren Andrews

Measurements reported in the paper were recorded in an active Green River, Wyoming, trona mine, partly as a teaching exercise and partly to provide the mine in question with additional input data for its ventilation network program. Measurements were made: - in representative three-entry intake airways in room and pillar sub-mains; - between the lower portion of a vertical down-cast hoisting shaft and the start of an intake airway system established in a room and pillar main; - in a representative downcast section of a divided vertical shaft, and of the collar entrance loss at the top of the same compartment. Pressure differences were measured with manometers and trailing hoses, air flowrates with calibrated anemometers, and barometric pressures and wet-and dry-bulb temperatures were recorded for density determinations. Where possible, results are quoted as Atkinson friction factors, and relevant measurements are recorded in some detail to show the magnitude of fluctuations in observed pressure differences.

Jan 1, 1987

By James S. Redpath

INTRODUCTION Background Early in 1972 our firm was asked by Cominco, managers of Arvik Mines Limited, to carry out an underground exploration programme referred to as the "Polaris Project" on a zinc-lead deposit in Canada's High Arctic. We had carried out numerous projects in the far north but this was to be the first long decline driven in perma-frost. Despite the short notice it was possible to meet the quickly approaching summer shipping deadline. We were able to do this by drawing heavily on our own and Cominco's background in Arctic operations. The project was an excellent example of owner-contractor co-operation and this spirit was responsible for the success of the project. Unusual Aspects There were a number of unusual aspects of the Polaris Project which are discussed in this paper. The extremely remote location, the short shipping season, and the fact that the work was carried out in permanently frozen ground, when combined with the lack of handy fresh water and a very severe climate, make it unique in many respects. Despite these handicaps, a record was set during the driving of the exploration decline.

Jan 1, 1974

By Robert N. Evans, Delon Hampton

During construction of the Washington Metropolitan Area Transit System, the hand-mining of a mixed-face condition was anticipated on a portion of tunnel located in the downtown area of Washington, D.C. The Section, consisting of two circular tubes, extends from Station 12+80, heading in a westerly direction, traverses along a curve under Lafayette Square, and ends in a northwesterly direction at Station 37+62 (see Fig. 1a). It was near the northernmost portion of the section that the mixed-face condition was encountered. Decomposed rock was first encountered in the invert at Station 31+00. From this point the rock gradually increased in height until it intersected the springline at Station 37+62, the project limit. Summarized within this paper are measurements of the soil load on a horseshoe-shaped portion of tunnel located in the mixed face condition. These measured loads are compared to the soil load on tunnels as determined by current design methods. The paper also discusses rib and surface movements associated with the post loading process. Comments will be made on how the presence of a mixed face condition might help or hender the tunnel design and construction procedures.

Jan 1, 1974

By D. B. Dreisinger, H. J. Sohn, J. S. Sohn, G. A. Kordosky

The transport of lithium through a supported liquid membrane was studied with a mixture of D2EHPA and TBP in kerosene as a mobile carrier. In the flat- sheet supported liquid membrane(SLM) system, experiments were carried out to investigate the effects of concentration of mobile carriers in the membrane solution, hydrogen ion in the feed solution, and temperature on the transport of lithium. Experimental results agreed well with a transport model for permeating lithium across the liquid membrane. The permeation rates of lithium can be explained in terms of diffusion of a Li-complex through the membrane phase. For a practical application of an SLM method, a hollow fiber module has been used and lithium can be concentrated more than three times in 24 hours.

Jan 1, 1993

By Russell. A. Smith

This paper describes some recent work on the identification and development of new chemical reagents aimed at improving the industrial processing of phosphate ores by froth flotation. In particular, three chemical product families which will be discussed appear to offer enhanced flexibility by: 1) utilizing a small amount of a silica control reagent which can significantly reduce the amount of anionic (carboxylic) collector required for a given P2O5 recovery level; 2) utilizing a new anionic collector family which offers high P2O5 recovery and selectivity versus standard carboxylic collectors; and 3) utilizing another new anionic collector family which has, in some tests, allowed for selective removal of dolomite from apatite. Examples and use characteristics of each of these new chemical ideas will be presented.

Jan 1, 1993

By Jon C. Yingling

Techniques for optimization of mineral processing flowsheets are reviewed. Though not yet widely used in the minerals industry, approaches for chemical process optimization based on successive quadratic programming (SQP) algorithms may be employed to determine optimum unit design and control settings for a mineral processing flowsheet. Moreover, in certain mineral processing flowsheet applications, specialized techniques can be applied because of the nature of the system relations. These techniques offer advanta es in efficiency. Moreover, their capability exceeds that o f the SQP approaches since simultaneous optimization of circuit configuration and unit controls can be addressed.

Jan 1, 1990

By Charles L. Karr

Researchers at the University of Alabama in cooperation with the U.S. Bureau of Mines have developed adaptive process control systems in which genetic algorithms (GAS) are used to augment fuzzy logic controllers (FLCs). GAS are search algorithms that rapidly locate near-optimum solutions to a wide spectrum of problems by mimicking the search procedures of natural genetics. FLCs are rule based systems that efficiently manipulate a problem environment by modeling the "rule-of-thumb" strategy used in human decision making. GAS and FLCs can be combined to produce powerful, efficient, and robust adaptive control systems. To perform efficiently, such control systems require a control element to manipulate the problem environment, an analysis element to recognize changes in the problem environment, and a learning element to adjust to the changes in the problem environment. I" this paper, the details of an ongoing research effort to develop and implement an adaptive process control system for a column flotation unit are discussed.

Jan 1, 1996

By Yoginder P. Chugh, K. V. K. Prasad, R. Missavage

This paper presents results of field monitoring and finite element studies to analyze and improve a room-and-pillar retreat mining system. Fie1 d instrumentation was utilized to monitor pi11ar load changes, roof to floor convergence and differential roof strata movement as retreat mining progressed and to determine in-situ horizontal stresses. A two-dimensional finite element model depicting strata behavior at this mine was developed and used to analyze existing and alternate improved mining geometries. The results showed excellent correlation between fie1 d observed and model predicted behavior. Some of the recommended changes in mining geometry based on the study were incorporated in the mining system.

Jan 1, 1986

By M. L. Gupta, S. P. Banerjee, D. C. Panigrahi

The paper describes the computer simulation of climatic conditions in the longwall workings in India. For this simulation work the longwall panels have been divided into two segments, viz; the intake gate segment and face segment. Two computer models, one based upon transient heat and moisture transfer algorithm of McPherson (1986) and the other on quasi-steady algorithm of Starfield and Bleloch (1983), have been developed for intake gate segments. Similarly two computer models, one based upon the transient heat flow in cylindrical tunnel with certain modifications of McPherson algorithm (1986) and the other on linear heat flow concept, have been developed for face segment. The models incorporate the necessary running and spot heat sources present in their respective segments. In addition to this the goaf heat flow parameters have been incorporated in the models for the face segments. Continuous recording of important thermal parameters have been carried out in several longwall faces in India to validate these models and the results have been presented.

Jan 1, 1993

By S. K. Mishra, S. B. Kanungo, D. Biswal

An attempt was made to beneficiate low-grade, high-phosphorus manganese ores of the Garividi-Garbham region of Andhra Pradesh, India, by using wet high-intensity magnetic separation (WHIMS). The distribution behavior of both mass and chemical constituents in different size fractions of a typical highly weathered ore sample was studied to obtain information about the liberation characteristics of various chemical constituents. Magnetic separation indicated that in the +208-µm size fractions, P and acid insolubles were concentrated in the magnetic fractions. However, in the -208-µm size fractions, P and acid insolubles were concentrated in the nonmagnetic fraction because of a lower recovery of the magnetic fraction. Variations in field intensity between 1.3 and 1.75 T had little effect on the recovery and the grade of concentrate. The results also demonstrated that phosphorus was associated with all three major constituent phases, namely, oxides of Mn and Fe and aluminosilicate gangue minerals.

Jan 1, 2000

By F. A. Kruse, R. J. Madrid, P. L. Hauff

Sub-microscopic gold grains in disseminated gold deposits in Nevada are often directly associated with the clay mineral illite. Delineation of gold ore-zones can be improved by accurate characterization of the associated illite varieties or polytypes. X-ray diffraction studies of clay minerals from several disseminated gold deposits demonstrate that illite polytypes reflect lateral and vertical zonation around the ore bodies. Polytypes act as geothermometers indicating temperatures of ore deposition and proximity to hypogene and supergene fluids. Visible/near infrared spectral measurements using a field-portable reflectance spectrometer provide a reconnaissance technique for mapping the in-situ distribution of illites. Changes in the visible/near-infrared reflectance spectra are observed as illites progress from the lower temperature, less ordered 1 M variety to the higher temperature 2M type. The combination of the reflectance spectroscopy with the X- ray diffraction data creates a powerful tool for detailed mineralogic mapping for gold exploration.

Jan 1, 1989

By George H. K. Schenck

Decisions to develop deposits of calcareous materials for cement production are based largely on anticipated markets for heavy construction which utilizes concrete. The geologist should understand the fundamental factors that underlie such management decisions, so that his field work and reports will more effectively relate to the information requirements of managers in the cement industry. The paper examines the relationships that exist between exploration and development of calcareous raw materials for cement manufacture and changing factors in the marketing of cement. Continued overcapacity, improved technology, changing distribution patterns, ease of entry, economics of scale, and the nature of product demand are some of the characteristics of the cement industry that are basic to decisions regarding exploration programs and property development.

Jan 1, 1966

By K. A. Natarajan, M. K. Yelloji Rao, P. Somasundaran

The bacterium Thiobacillus ferrooxidans triggers the surface modification of sulfide minerals to provide hydrophilicity or hydrophobicity for the flotation of sphalerite and galena. The effects of initial cell concentration, period of biotreatment and pulp density on the floatability of the minerals are discussed. With galena, flotation enhancement obtained through sulfuric acid treatment was retarded by biotreatment at all cell concentrations due to chemical effects. Such a decrease occurred for sphalerite only at cell concentrations sufficiently high for bacterial attachment to the mineral surface. The variables affecting surface modification (and, thus, flotation response of the minerals) include the cell concentration used for bacterial conditioning, the period of biotreatment and the pulp density. Although bacterial growth during biotreatment was observed even in the absence of nutrients, such growth was more common in the sphalerite suspension than in the galena suspension. Cell protein estimations suggest that more cells are attached on galena than on sphalerite. Probable reaction mechanisms associated with bacterial modification are discussed.

Jan 1, 1993

By I. Iwasaki, K. A. Smith, X. Cheng

A cathodic decomposition model was examined for both pyrrhotite and chalcopyrite in an attempt to analyze the formation of surface coatings in deoxygenated solutions at natural, near neutral pH. Combination potentials established between the mineral-grinding media pair were simulated by applying a potential of -0.455 V (vs. a standard hydrogen electrode) either to a pyrrhotite or to a chalcopyrite electrode. Chronoamperometry was used to study the polarization behaviors and alteration of mineral surfaces through cathodic processes. The kinetic parameters of cathodic decomposition of pyrrhotite and chalcopyrite were determined and compared. It was concluded that pyrrhotite decomposed faster than chalcopyrite in near-neutral pH solutions. Both minerals were then covered by a film consist¬ing mainly of iron hydroxides, which adversely affected their flotation.

Jan 1, 1999