Search Documents

By A. K. Bakshi, Komar S. Kawatra

A plant trial of a new on-line pressure vessel rheometer for slurries, developed at Michigan Technological University, was carried out at a nearby copper concentrator. The rheometer measured the flow curves (shear stress vs. shear rate) of chalcocite slurries. Viscosity of non-Newtonian slurries changes with shear rate and so, for such slurries viscosity measurement at a single shear rate (often seen in the literature for grinding and classification studies) cannot be correlated to process performance. For these slurries, viscosity at various shear rates can be measured from flow curves generated by the pressure vessel rheometer. Other rheological properties, such as flow type and yield stress can be determined by this rheometer to better characterize the slurries. The slurry at the copper concentrator consisted of ground chalcocite ore. The solids content in the slurry varied between 30-60 % by weight. Top size of the particles was 125 micron, and 80% passing size was 34 micron. Measurements by the pressure vessel rheometer showed that most of the slurries had pseudoplastic flow at shear rates below -3000 sec-l, where the viscosity of the slurry decreased with increase in shear rate. Above -3000 sec-l, like a Newtonian fluid, the viscosity of the slurry remained steady. Flow curves and viscosity from the pressure vessel rheometer were verified with a Brookfield viscometer and a vibrating sphere viscometer, and the results were found to be accurate.

Jan 1, 1997

By Robert A. Jankowski, Natesa I. Jayaraman, Jay F. Colinet

The U.S. Bureau of Mines evaluated the dust control effectiveness of two-phase flow systems in a full-scale model mine using a mockup of a Joy 14CM continuous mining machine. In a two-phase flow system, air and water flow simultaneously through the nozzle. Air pressure varies from 10 to 60 psi, and water at 30 to 50 psi. Coal dust was introduced at the face, and dust concentrations were monitored at the operator locations and in the return. When compared with a conventional spray system, a symmetrical two-phase flow system reduced dust levels during the box cut by 43 pct at the operator location, and 30 pct in the face return. Dust levels, however, increased at the off-operator position during the slab cut. A directional two-phase flow system reduced dust levels at both operator locations by more than 90 pct in the box cut mode. While the use of two-phase flow systems will reduce respirable dust levels and water usage, it requires an air supply to the miner. Moreover, the ability of the two-phase flow system to redirect the dust cloud makes nozzle orientation a critical factor.

Jan 1, 1991

By F. Forbes

For many years, the Machinery Division of Dravo Corporation has been designing and constructing bins and hunkers as part of overall plant facilities. We have designed bins to handle a variety of materials including coal, coke, iron ores and concentrates, sintered and pelletized ores, calcined and raw limestone, bentonite, alloys for BOF shops, and even cast iron chips from machining operations. We, along with everyone else in this business, have had our bin problems. The bins either plug, rathole, segregate, wear out, flood the discharge device, or overload it. Surprisingly, sometimes they have worked. As engineers, it has long concerned us that something as important as bin design should be so imprecise and that it has been so conspicuously avoided in research and in literature. In past years, rule-of-thumb design criteria had been to keep the sides of the bins as steep as possible and the outlets of the bin as large as possible. This criteria led to the design of bins with 600 to 700 side slopes and table feeders which were very large. Unfortunately, this meant trying to fit tall, skinny bins into a layout where minimum building height was required for obvious economic reasons. Like everyone else in the industry, we found that this design procedure was expensive and ineffective.

Jan 1, 1968

By K. S. Narayanan, Marcia L. Bartges, K. S. Venkataraman

The starting powders' physicochemical properties and consistency are essential for technical ceramic products to meet their performance specifications. The need for finer and more consistent powders has opened new technologies for synthesizing powders from atoms and molecules. However, submicron and near-micron powders obtained from conventional comminution and classification techniques are still competitive. This paper shows several examples from electronic ceramic applications of how we can use powder characteristics for micromanaging by design the ceramic properties such as the green and fired densities, slurry rheology, shrinkage during sintering, and the microstructure of the sintered bodies. The cross-disciplinary nature of the technology requires that the researcher not only should have a firm grip on the fundamentals of one or more disciplines, but also should be generally aware of the intricacies of other disciplines as well.

Jan 1, 1992

By Gemei Yang, Pierre Mousset-Jones, Felipe Calizaya, Malcolm J. McPherson

Laboratory tests on controlled airflow recirculation have shown the development of transient states in response to changes in system prevailing conditions such as those generated by a sudden start-up and stoppage of fans. Researchers in many European countries have developed various models to explain these phenomena. However, these models failed to consider some important factors such as diffusion and dispersion of gas in turbulent flows. For both in-line and cross-cut recirculation, tests have shown that after the start- up of a booster fan, the gas concentration in the system fluctuates, reaching high levels at the initial states and slowly dying out with time. These fluctuations cannot be represented adequately by simple step-wise functions but rather by smooth, albeit complex equations. In this paper, the phenomena are explained by the convection-dispersion theory, and represented by a mathematical model. Based on a few simplifications and applying Fourier's Transform Method to the differential equations of the flow recirculation model, an integral form of gas concentration function was derived. The Simpson Integration Method was used to compute numerical results for two laboratory tests. The paper also discusses the range of the dispersion coefficient to improve the accuracy of the model.

Jan 1, 1989

By B. J. Arnold, F. F. Aplan

A model incorporating rate and residence time to describe the froth flotation process was used to provide data for the evaluation of various kinetic flotation models and to provide scale-up information from laboratory to industrial scale coal froth flotation. Rate constants were determined in laboratory and plant froth flotation tests and the residence time distribution was measured for a bank of four 21 ft 3 (0.6 m3 ) WEMCO cells treating Upper Freeport seam coal and a bank of four 300 ft 3 (8.5 m3 ) cells treating Lower Kittanning seam coal. It was found that a lag time for continuous flotation should be incorporated into scale up models and that a kinetic froth factor ratio of between about 2.0 and 2.8 should also be used to scale up data from laboratory to plant scale.

Jan 1, 1989

By Mark S. Dunsbier, Steven J. Schatzel

Large roof outbursts began occurring in November 1986 at Domtar's Sifto Salt Mine in Goderich, Ontario, Canada, working the bedded Salina A-2 Salt unit. The outbursts, measuring about 13-20 m in diameter, released high concentrations of methane from cavities that extended into carbonate roof units. Spontaneous ignitions of methane gas during an outburst seriously burned a mine technician. The Canadian Ministry of Labour contacted the U.S. Bureau of Mines for technical assistance to aid in mine managements1 efforts in alleviating the problem. Initial gas content determinations of salt samples from the outbursts by acoustic test methodology revealed no methane enrichment. In- mine core drilling and subsequent methane content testing indicates the main source of methane in overlying roof units. Drilling the roof units demonstrated the potential of draining methane from areas showing signs of impending outbursting and alleviating the danger. Three mechanisms are considered the most likely means by which methane was introduced to the mine environment. These are (1) hydrocarbon gases released from brines, (2) gas transport along horizontal bedding planes or gas accumulations in bedding separations, and (3) mining-induced fracturing. The abundance of higher hydrocarbons in gas yielded by non-evaporite rock samples from the Goderich mine may be indicative of a former association with liquid petroleum.

Jan 1, 1989

By Shallesh K. Patel, Richard M. Powers, Patrick Zhang

Perceived environmental impacts from flotation reagents used in the phosphate industry have been of concern for nearly a decade. A research program was initiated to determine the distribution, fate, and consequences of flotation reagents (fatty acids, fuel oils, and amines) within the environment. Therefore, laboratory investigations of biodegradation and soil attenuation of the reagents were conducted along with field flotation mass balances and groundwater investigations in clay settling, sand tailings, and undisturbed areas. Sample analysis and a reagent mass-balance model indicated that most reagents are distributed in clay settling and sand tailings areas. Groundwater analyses showed no fatty acids or amines in any of 19 surficial or intermediate aquifer water samples. In contrast, fuel oils were detected in the surficial aquifer at all sand tailings areas in concentrations ranging between 8.5 and 0.5 mg/L. Fuel oil was also detected in trace amounts (0.6 mg/L) in one intermediate aquifer well located in an active sand tailings area. All fuel oil concentrations detected were very low and, coupled with a biodegradation rate of approximately 10% per month, all concentrations should be within reference levels in six months. Based upon the results of this study, use of flotation reagents in the beneficiation process of the Florida phosphate industry present no long-term threat to the environment.

Jan 1, 1999

By C. W. Nelson, A. G. Moody

This paper describes the design, equipment selection and onshore fabrication of the largest facilities module ever installed in a single lift in the Gulf of Mexico. Measuring 35.5 x 70.1 x 21.3 m (110 x 230 x 70 ft), the three operating level structure houses Frasch process sulfur mining equipment and weighed nearly 49 million N (5500 tons) during lift. An operating weight of over 74 million N (8300 st) combines with bridge reactions acting on the in-place module and results in a total operating vertical load on the supporting platform deck of about 107 million N (12,000 tons). A Vierendeel truss structural system was selected for framing the module to allow maximum equipment access and routing flexibility for complex, insulated large diameter process piping. Research and finite element analysis of crimp plate siding behavior in shear was carried out during selection of siding type for the module. An interactive design sequence was carried out that incorporated in-place operational criteria, onshore fabrication considerations, complex process equipment requirements, plus load-out, ocean transport and offshore lift analyses. Project schedule dictated that design, procurement and fabrication be fast-tracked with parallel activities accelerated to the maximum extent possible. Design and construction of this largest and most complex module was done concurrently with 52 other components of the project including jackets, decks, process and living quarters modules as well as two 122 x 22 m (400 x 72 ft) sulfur tankers. Total tonnage of steel structures for the project exceeded 90.7 kt (100,000 st). The 5 kt (5500 st) mining module proved the viability and costeffectiveness of larger modules than commonly used in Gulf of Mexico waters. This technical advance can be matched with economic opportunity for other large-scale offshore installations.

Jan 1, 1994

By W. L. Cornell, F. W. Benn

The U.S. Bureau of Mines investigated froth flotation techniques to remove heavy metals (Pb, Cu, and Zn) from southeast Missouri lead mill tailings. It has been estimated that southeast Missouri contains between 200 and 300 million st of Pb tailings stored above ground. The tailings were classified as two distinct types: (1) pre- 1968 tailings from the Old Lead Belt (some more than 100 years old) and (2) post-1968 tailings from the New Lead Belt. The objectives of the investigation were to reduce the Pb remaining in the tailings to (500 ppm (<0.05% Pb) and to attempt to recover a marketable concentrate to offset a portion of the remediation costs. The remaining dolomite-limestone would then be used as mining backfill or agricultural limestone. Bench- scale froth flotation removed, in percent, 95 Pb, 84 Cu, and 54 Zn, leaving 94% of the original weight containing, in parts per million, 400 Pb, 40 Cu, and 300 Zn from the Old Lead Belt tailings. Separate flotation tests also removed, in percent, 85 Pb, 84 Cu, and 80 Zn, leaving 75% of the original weight containing, in parts per million, 400 Pb, 200 Cu, and 500 Zn from the New Lead Belt tailings . Concentrates recovered from the Old Lead Belt were retreated to produce a final Pb concentrate containing 72% Pb with a cleaner flotation recovery of 79%. Froth flotation proved to be a viable method to remove the heavy metals.

Jan 1, 1992

By R. A. Jankowski, R. Gong, R. Bhaskar

The control of respirable coal dust in continuous mining sections involves careful analyses of the generation and transport of the dust, including airflow pattern analyses. Potential dust control devices must be evaluated based on their effect on both local dust transport and potential dust exposure of face personnel. The development of larger and more productive continuous miners increases the need for research on dust control and improvement of visibility in the face area. Two studies relating to underboom dust control are discussed. The first study involved the valuation of potential underboom dust control techniques to reduce operator exposure to dust and determining the relationship between the positioning of exhaust ventilation and the exposure of face personnel as a function of face and operating variables. The study involved full-scale laboratory experiments using a state- of-the-art data acquisition system. The second study related to the use of foam under a continuous miner boom and its effect on silica concentration and respirable dust. The foam study was performed in a coal mine. The laboratory studies involved the fabrication of a full-scale test facility and development of a computer based data acquisition system. This was followed by baseline data collection, smoke trace tests, detailed performance testing of various underboom dust control measures and data analyses. The underground foam test involved the design and installation of the foam generation and delivery system, testing, and data evaluation. The results of the studies are summarized in this paper.

Jan 1, 1991

By M. Canty

This paper presents results from pilot-scale and field testing of an innovative technology that uses sulfate-reducing bacteria (SRB) to treat and control acid mine drainage (AMD). Sulfate-reducing bacteria, a common group of anaerobic bacteria, produce hydrogen sulfide and bicarbonate when supplied with sources of carbon and sulfate. Hydrogen sulfide reacts with metal ions in AMD, precipitating them as metal sulfides. The bicarbonate produced serves to help neutralize the drainage. Pilot-scale metal-removal efficiencies reached 99% for zinc, 99% for aluminum, 96% for manganese, 98% for cadmium and 96% for copper. However, the iron and arsenic removals were not as effective as the aforementioned metals. This was largely attributed to high levels of iron and arsenic that contaminating the organic substrate. There was evidence that both adsorption and sulfate reduction were occurring within the reactors. The SRB field demonstration involved using the flooded subsurface mine workings of the Lilly/Orphan Boy Mine near Elliston, MT, as an "in situ biological reactor." In the mine, high removal efficiencies were observed for aluminum, cadmium, copper and zinc (70% to near 100%) during the four years of monitoring. However, for reasons similar to the pilot scale testing, low removal efficiencies were observed for arsenic and iron. Sulfate reduction was evident by measured decreases in sulfate and the detection of soluble sulfide within the mine water.

Jan 1, 2000

By Richard R. Radel, Jack Barry

Contract required excavating 2,000 If of 14&apos; horseshoe tunnel in rock, a 95&apos; deep work shaft on shore, and a 50&apos; deep intake shaft located in the middle of the Niagara River just above Niagara Falls. Large quantities of H2S were encountered in the range of 20 PPM with ventilation. Peak levels of 40 PPM were recorded. The original designed ventilation system required only a volume of 10,000 CFM to meet OSHA requirements. The volume of air was increased to 50,000 CFM to dilute the H2S to al- low workmen to work and comply with OSHA H2S action levels. The second phase of the tunnel consisted of placing 72" ID X 20 foot long concrete reinforced pipe in the tunnel. When the tunnel was holed through and both shafts were open, a substantial amount of work was required to take place in the shafts which eliminated the possibility of placing a bulkhead to secure proper ventilation. The ventilation team designed a jet system airlock. The design of this system was to bring fresh air down the work shaft in two duct systems; one 30" diameter and one 24" diameter. Following the excellent work of Jan Wolski (7th Mine Ventilation Symposium chapter 58) our design incorporated nozzles located approximately 100&apos; in by the work shaft. The velocity of the 24" diameter duct was 6,365 FPMD2.2 MPH. The velocity of the 30" diameter duct was 6,117 FPMl69.5 MPH. Both systems were on blow and being that air expands at 3112 degrees per side this high velocity of air expanded and created an air bulk head through which men and the large sections of concrete pipe could be passed without any delay or additional cost to the project.

Jan 1, 1997

By Scott Jones, Tony R. A. Durkac, David W. Stephens

Williams Mine was considering spending a large amount of capital to install a pumping system underground to rid the mine of slimes; with the introduction of Delvo Stabilizer this challenge would be met. This paper will address the process to introducing the Delvo Technology into the Cemented Roddill Program. Some areas that were worked on included: testing of the mix design, bet dosage rate for an economical solution, temperatures at different levels of the mine, the amount of time needed once the grout was put to sleep, preventing plugs in the delivery system A controlled dosage that gave the Operator a 12 hour window of flowable material was developed and an added feature to the introduction of Delvo was also noted; an increase in MPa strength over the design. Collectively with the help of operators at the batch plant and the underground miners involved with the program all concerns where addressed and all goals met. A cost effective program was implemented thus increasing productivity, preventing costly plugs, and improved the actual maintenance on the entire delivery system, which included the batch tanks, aggitator tanks, all pumps required in the system and of course reducing buildup of slimes at the cones.

Jan 1, 2001

By Lijun Xu, Jan M. Mutmansky

The purpose of this research was to investigate airborne coal mine dust characteristics in order to assess the possibility of contribution of these characteristics to the incidence of coal workers&apos; pneumoconiosis (CWP). The characteristics studied included physical (mass concentration and size distribution), chemical (elemental composition), and mineralogical (quartz and kaolinite content) variables of the dust. The results are based primarily upon analysis of the characteristics of 99 impactor samples from 18 mines in seven states. Because the eight stages of the impactor span the range of dust sizes up to 20 microns, the characteristics analyzed should represent respirable dust characteristics well and also provide size-dependent representations of the characteristics. In general, the patterns of mass concentration and size distribution in the various mines studied were similar with mass concentrations being high downwind of the continuous miner. The concentrations and size distributions were more variable upwind of the continuous miner, apparently as a result of the variations in the dust conditions in the working section. Significant size effects on the elemental and mineralogical content are shown in the data. Concentrations of most of the elements decrease as size decreases. However, minerals content increases as the dust size decreases. Regional variations of elemental and mineralogical content are also significant. Quartz and kaolinite contents are small in regions with low incidences of CWP. However, the elements of Cu and Zn are high by comparison to their content in high-incidence coal fields and may have the effect of protecting against the disease.

Jan 1, 1991

By J. Wes Blakely

In the mid-1950s the importation of foreign oil began to encroach on traditional coal markets such as railroad steam engine fuel, home heating, electrical generating plants, and others. Many of the smaller coal companies with substantial coal reserves subsequently found that they could no longer continue to mine economically and merged in various ways with larger established coal mining concerns. As the seats of top management and authority were removed from the mines to large metro centers such as New York, Pittsburgh, and Chicago, the more personal relationship between mine workers and management that had existed prior to these mergers began to be eroded and replaced by " remote control " mine management. The disappearance of this face-to-face contact of upper management with mine employees tended to create barriers blocking simple effective communications between coal mine management and labor. In examining the human relations aspects of the coal mining industry, many elements, some concerned with work and others not, have depicted the industry as almost devoid of good applied human relations and communications practices, and, in truth, little has been done to alleviate this situation. In past years many coal producing companies, with the exception of one of the largest, failed to adequately define the term "communications" as it applied to their companies, whether internally or externally. Internally many still place heavy reliance on written communications such as company-wide newspapers to do the job of communicating with their employees which they feel ought to be done. One company puts an inordinate belief in its company "newspaper" as the primary instrument to stimulate its work force into increasing productivity. Primarily aimed at the workers, who greatly outnumber the salaried administrative people, this publication mainly documents the fortunes of individual mine workers who are felt to have achieved something with their lives, e.g., a mine worker who had managed to put four children through universities, the philosophy behind this being to inspire other workers to achieve worth- while goals.

Jan 1, 1981

By J. W. Stevenson

The need for a separate ventilation department within the management team was recognized by the management of U. S. Pipe and Foundry before the company was purchased by Jim Walter Corporation in January, 1970. Because the coal beds of the deep underground coal properties owned by Jim Walter Resources lay 1300 to 2200 feet below the surface, efficient mine ventilation practices are essential through shaft openings varying from 16 to 22 feet in diameter. The extremely high methane gas quantity indicated to be in the coal bed because of the depth of cover and documented by various U. S. Bureau of Mines tests and demonstrated by early mining proved the need to implement this early management decision. At U. S. Pipe and Foundry mine ventilation was a function of the Mining Engineering Department with ventilation personnel assigned to the mine receiving their day to day work assignments from the mine manager or mine foreman. At Jim Walter Resources, the General Manager - Ventilation reports to the Senior Vice President, Mining Engineering, who reports directly to the President, Mining Division, Figure 1 (Company Organization Chart). Position descriptions are static; however positions are dynamic and consequently the degree of emphasis of specific duties and responsibilities change depending not only upon the aptitude of the individual performing the job but also upon his ability to meet the needs of his supervisors; and ultimately upon his ability to react to the economic forces directing our society. The following describes the duties and responsibilities of the General Manager - Ventilation, Figure 2.

Jan 1, 1980

By S. K. Kawatra, S. A. Moffat, K. A. DeLa’O, T. C. Eisele

It was observed that the efficiency of some autogenous grinding circuits was dependent on temperature, with the energy-efficiency of the grinding process decreasing in the winter months, accompanied by an increase in critical-size production. Several possible causes of this phenomenon were suggested, including: • Increased brittleness of the ore during blasting in the pit at low temperatures, leading to increased levels of internal cracking that would lead to rapid breakage to critical size in the mill; •Brittleness changes of the rock in the mill; and • Changes in the durability of the rock caused by either formation of ice on the surface, or freezing of water inside the pores and cracks of the rock. To determine which mechanisms were occurring, drop tests were carried out using frozen and unfrozen rock with varying degrees of porosity, both dry and water-saturated, and which had been blasted for mining in summer and in winter. These tests showed that there was no difference between the summer-blasted ore and the winter-blasted ore, and that durability changes in dry rock over the temperature range from 25ºC to -25ºC were negligible. However, water-saturated rock showed an increased resistance to breakage upon freezing, particularly when the rock was highly porous, or when a layer of ice formed on the surface. Seasonal changes in the durability of rock in grinding are therefore due to formation of ice in and around the rock.

Jan 1, 1995

By L. Xu, R. Bhaskar

The trends in dust exposure levels and longwall production over the last 20 years were examined. The study was conducted for nine major underground coal mining states: Alabama, Colorado, Illinois, Kentucky, Ohio. Pennsylvania, Utah, Virginia and West Virginia. The dust exposure and shift production data were obtained from the Mine Safety and Health Administration (MSHA). Trends were identified and analyzed for the headgate, tailgate, jack setter and shearer operator positions. The relationships between average scam height and dust exposure levels as well as the percentage of dust samples exceeding the dust standard for the four occupations were examined. The concentration to production ratio, a better indicator of the success of dust control measures, was calculated for the 20-Year period. The data show that, in general, dust exposures over the last two decades hare decreased. However, it appears that much of the decrease was in states that had significantly high dust exposure levels (such as Alabama and Utah), while for states such as Virginia, West Virginia and Pennsylvania, the decrease was not as dramatic. Major reductions were made in the period starting in 1982, when a host of longwall dust control techniques was introduced. However, nearly 35% of jack setter and shearer operator dust exposures were still above 2 mg/m3 in 1990, with nearly 20% of tailgate operator exposures and 8% of headgate operator exposures being above the federal standard. The concentration/production ratio has shown a remarkable decrease since 1981. This indicates that long wall operators have been able to meet increased production as well as, to a large extent, control chest production at the face. An analysis of the relationship between average seam height and dust concentration for the years 1984 and 1990 shows that while in 1984, the dust concentration could be correlated to seam height, in 1990 the relationship was less definitive. This indicates that technological factors may be more important than seam height.

Jan 1, 1994

In 1991, most industrialized countries, except for Germany, were in a recession or a period of reduced growth. The US economy, already in recession, suffered from mounting banking system losses and the uncertainty brought about by the Persian Gulf War. However, US and worldwide minerals exploration did not collapse as it did during the mid-1980s. Even though gold and base metal prices declined, prices were still above cash costs for most operations. This allowed the continuation of established exploration programs but sharply limited new initiatives. Exploration 1990-1991 Planned worldwide 1991 exploration expenditures declined by about 8% from 1990 levels, according to a survey of 153 companies by the Metals Economic Group (MEG). Canada was the leading exploration target with 23% of the total, followed by Australia and the US (19% each), South Africa (13%), Latin America (11%) and the South Pacific (7%). The remaining 8% was split evenly between Europe and the rest of Africa. In Latin America, Mexico and Chile are the most attractive countries for exploration. Recognizing the risks involved, the industry has been cautious about ventures in the former Soviet Union. Survey results also showed that while the majors expected to maintain exploration spending, smaller firms were cutting back or actively seeking farm-outs from the majors (personal communication, M. Wegener, MEG).

Jan 1, 1992