Search Documents

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts (CCB). Alkaline combustion byproducts are gaining increasing usage for acid mine drainage (AMD) mitigation as research leads to a better understanding of their beneficial applications. Since January 1997, Mettiki Coal has been injecting alkaline flue gas desulfurization material from Virginia Power's Mt. Storm Unit No. 3 wet limestone scrubber into abandoned portions of the active Mettiki Mine.

Jan 1, 1998

By Tim Wolf

The author has seen an increased use of shaft-mounted, right angle drive assemblies. These designs use the pulley shaft as its 'foundation" and can create significant overhung loads. To reliably perform, the pulley and shaft must be designed for these special requirements. This paper will focus on the development of overhung loads and their design effects. Special considerations to maximize performance will be presented and comparisons with other drive options will be made. Experience in heavy mining applications will be used throughout.

Jan 1, 2000

By Ross W. Smith, Xiapeng Zheng, Peggy J. Arps

The adhesion (and de-adhesion) of Bacillus subtilis to dolomite was determined under a number of conditions of initial concentration of the organism, agitation, mineral particle size and temperature. Rate equations curves for both adhesion and de-adhesion were constructed, with the rates of de-adhesion being about half that of adhesion. From the temperature data the energy of adhesion was determined to be about 1.02 kcal/mol. Adhesion of dolomite to B. subtilis follows a Langmuir isotherm. Equilibrium constants, adhesion capacity and Gibbs free energy of adhesion of B. subtilis to dolomite (at pH 6.6) were determined. These values were compared to similar data for adhesion of B. subtilis to apatite and dolomite.

Jan 1, 2002

By J. M. Rotter, R. A. Lohnes, J. Y. Ooi

Reliable prediction of wall pressures in a coal silo demands careful characterization of the stress-strain properties of the coal. This paper describes the results of triaxial compression tests on a typical fine-ground coal used in power generation and describes the fitting of several different constitutive models to the data. The fitted parameters for the constitutive models are well suited to application infinite element analyses. The different models are used to give the reader flexibility in choosing a model and to show the shortcomings of some models. To explore the quality of the fitting process, the fitted results are compared with finite element predictions of the triaxial test itself.

Jan 1, 1998

By A. E. Stewart

Slope design in an open pit mine includes determining bench height, bench face angle and berm width. Case histories are presented of two highwall slopes (160 and 220 m or 525 and 720 ft high) excavated in dipping strata in an op¬erating coal mine. These examples illustrate the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in approximately the same lithologic and structural environment. The main differences between the slopes were the angle at which the bench faces were excavated and the excavating methods that were used. Relevent aspects are also described of the engineering geology, slope design and excavation procedures.

Jan 1, 1998

By Nikolay M. Sirakov, Michael L. Feves, Rumen P. Mironov, Daniel R. Hack

Subsurface investigation of sand and gravel deposits has generally been limited to test pits and borings. These techniques are problematic in terms of the accuracy, usability, and cost of the final data. Innovations in the application of geophysics have been gaining acceptance in the aggregate industry, especially to determine depth to bedrock and the extent of uneconomic inclusions. This paper presents a system to optimize the processing and evaluation of electrical resistivity data. The system uses 3D separation, geometrical reconstruction, and visualization of subsurface objects.

Jan 1, 2002

By Ben L. Seegmiller

The basic compression-yield concept of roof support for mine roadways requires that the mine roof be placed in a state of compressive stress. The compressive stress may be achieved using a support system such as an entry truss or other specialty truss device. Furthermore, the roof must be allowed to yield, but with great resistance when abutment loads are placed on the roadway. The resisted yielding may be provided using a new yieldable steel prop, known by the trade name, YIPP~. The yieldable steel prop can allow as much as 1.5 m[5 ft] of yield, or up to approximately 40% of the opening height, while providing a resistance in excess of 60 mt[66st]. More than fifteen mining operations including coal, trona and hard rock mines have field tested the YIPPI . Present results indicate that the yieldable prop provides a cost-effective alternative to wood cribs, concrete cribs, hydraulic props and other steel prop supports. The paper describes the YIPPI including its unique principle of operation, its applications and actual field performance.

Jan 1, 1992

By R. C. Ford

The advent of solvent extraction-electrowinning (SX-EW) technology for recovery of copper from low grade oxide ores has extended the operational lives of many historic mines in the western United States, and made many other orebodies economically viable worldwide. Many of these operations are mature and face closure within the next decade, depending on market conditions. Closure of a large copper heap leach operation has not been undertaken, and differs in some important chemical respects from closure of gold leach pads. Challenges for closure include prediction of solution chemistry and draindown characteristics, determining the benefit of cover placement in semi-arid climates and evaluation of solution management strategies once the economics of copper recovery are no longer favorable. This paper discusses issues pertinent to copper heap closure in semi-arid and arid climates, and strategies for their management.

Jan 1, 2000

By A. Unal, R. L. Grayson

The use of radio frequency identification (RFID) technology to solve informational needs in isolated and restricted underground mining environments are reviewed, and the specifications of some of the past and currently available systems are presented. The advantages and disadvantages of using various frequencies, system configurations and specific components, including their construction standards and capability, are also discussed. The remaining challenges to the more widespread use of RFID systems for personnel and vehicle tracking are identified, and recommendations concerning the operating environment capabilities are detailed. Finally, the ultimate requirements for maintaining system integrity during and following a coal mine emergency are discussed.

Jan 1, 1999

Political events during the past decade have caused businesses throughout the world to think globally. Countries once closed to free market enterprises are now open and seeking out foreign investment to help improve the well being of their populations. The mining industry has always been a global one. Today, though, the industry has become even more global. The driving forces behind this include the opening up of higher grade, lower cost mineral deposits in undeveloped and developing nations. In addition, permitting delays in the United States, coupled with stricter environmental guidelines and a general anti-mining attitude, have forced the mining industry to look outside US borders. The Mineral Economics and Management Society (MEMS) took as the theme of its seventh annual professional program "Economic Globalization of the Mining Industry." About 100 people attended the conference held in Arlington, VA in late March. Speakers included members of the investment community, academia, government and the mining industry.

Jan 1, 1998

By Robert Snow, Francisco Sotillo

Six types of amines were evaluated in the cleaning step of the rougher concentrate for the Crago “Double Float” process in terms of relative selectivity. Selectivity of these amines was ranked based on both batch and locked cycle flotation tests. Two parameters were used for selectivity ranking, the Selectivity Index, SI, and the ratio of insol rejection to the tailings weight percentage, R*. The comparison of the flotation results of the batch tests of the cleaning step of the Crago process for an unsized amine feed generated the following ranking from the most selective to the least selective mine: Quaternary > Primary [ ]Tertiary [ ] Condensate > Ether > Secondary(?).

Jan 1, 2002

By David S. Yantek, Paul Jurovcik, Eric R. Bauer

Workers in coal preparation plants, where vibrating screens are significant noise sources, are often exposed to sound levels exceeding 90 dB(A). The National Institute for Occupational Safety and Health, a major coal company, and a vibrating screen manufacturer conducted a cooperative study of vibrating screen noise. Rubber isolators reduced sound levels by 1 dB. Urethane screen panels did not reduce sound levels in this case. Drive noise was determined to be the dominant noise source on the screen. Damped side plates reduced vibration levels on the screen sides by 1 to 7 dB(A). Detailed results of the study are presented.

Jan 1, 2005

By J. Pang, S. Chander

The mechanisms of chalcopyrite oxidation in alkaline solutions have been studied using cyclic voltammetry and impedance spectroscopy techniques. The cyclic voltammetry was used to elucidate oxidation/reduction reactions, whereas impedance spectroscopy was used for in-situ characterization of the interface. To analyze the impedance spectra, equivalent circuit models were constructed based on a layer- wise growth of reaction products. Parameters of the equivalent circuit were calculated by comparing the experimental spectrum with that expected on the basis of equivalent circuit. From the value of equivalent circuit parameters, properties of the surface layers were inferred. These properties change substantially with the change in oxygen and/or collector concentration in solution. From such changes the effect of oxygen and collector concentration on the contact angle and flotation behavior of chalcopyrite were interpreted.

Jan 1, 1991

By J. M. Mutmansky

This paper outlines the results of a study of the opinions of practicing engineers concerning the value of environmental engineering courses in a mining engineering curriculum. One hundred engineers with significant experience in mining-related engineering work were carefully chosen. Of the 67 responses, about half were from mining engineers, and the other half were from environmental engineers. In this paper, the results of the survey are outlined. The number and type of courses recommended by the respondents are summarized as well as the specific topics recommended for inclusion in a mining engineering curriculum. The survey form also asked for the stages in the mine life when environmental experts were needed and the percentage of environmental engineering performed by outside experts for many mining-related environmental tasks. The results of this line of questions are provided. Finally, the paper offers a comparison of the results for environmental engineers and mining engineers and analyzes the differences.

Jan 1, 2003

By Arthur B. Steiker

Digital simulation was used to model a proposed underground' train system. The trains are to haul ore from numerous loading points beneath the production area of the mine to a central underground dump location, and then return to the mine. The purpose of the simulation was to aid mine engineers in studying various alternatives and configurations regarding track layout, crusher (dump point) specifications, dispatch procedures, fleet size, and train length, among others. The simulation' model can also be used to study the same aspects of existing haulage systems. To accommodate a wide and initially unknown range of system designs, a modular model structure was developed with major components devoted to track routing, train movement, loading process, dumping process, and dispatch. Key statistics tabulated were number of trains dumped during a simulated week, queueing delays in the mine and at the crusher, crusher utilization, cycle time, and percent of time for each: activity (loading, moving, dumping, etc.). The simulation results were instrumental in identifying a train system design which would reduce queueing delays and meet production goals with a minimum of trains and track mileage.

Jan 1, 1982

By Ruston A. Ford

This paper reviews the development of the David Bell Mine, from early exploration, through discovery, construction, start-up, underground development, and production. Details are provided regarding the mine development, the mechanized cut and fill stope production, the proposed long-hole stoping with delayed backfilling mining method for the lower levels and the cyanide leach carbon-in- pulp concentrating process. The mine development remains on schedule and under budget with results very much as predicted in the feasibility study.

Jan 1, 1987

By Anthony D. Hammond, Charles A. Kliche

A slope stability study for the Annie Creek and Foley Ridge Mines was undertaken to provide Wharf Resources, Inc. with a technical assessment of the stability of the slope for an overall pit slope angle of 60°. A rock analysis of the most critical and persistent combination of discontinuities was carried out using probabilistic methods. A detailed discontinuity mapping and assessment of the rock mass provided the orientation data used in this study. The orientation data were reduced and analyzed to identify the discontinuity sets. A statistical analysis provided information about the distribution of the data. A deterministic wedge stability analysis identified the critical combination of discontinuities; those with a low factor of safety were further studied using probabilistic kinematic and kinetic stability analyses. The results from this approach were used to obtain the reliability or probability of failure of the slopes.

Jan 1, 1988

By N. L. Piret, R. J. Wesely, A. E. Melin, A. D. Zunkel

At the end of the sixties new iron precipitation techniques as jarosite, goethite or hematite brought about the new generation of electrolytic zinc plants, thereby terminating the multitude of existing neutral leach residue treatment schemes. Since the eighties, increasing environmental impact considerations urge the conversion of these contaminated waste generating precipitation processes to techniques which either produce environmentally acceptable residues or minimize their formation thereby generating iron-bearing byproducts. Technologies identified and economically assessed include the hematite process either suitably improved or with subsequent upgrading, the iron extraction process and the direct smelting of neutral leach residue to slag and fumed zinc oxide.

Jan 1, 1993

By Maurice C. Fuerstenau, Bruce R. Palmer, R. E. Johnson, B. R. Palmer, G. W. Warren

The environmentally sound processing of metal-bearing chloride solutions plays a key role in the extraction, plating, recycling, finishing and surface preparation of metals. Additionally, many chloride-bearing waste streams must be processed to obtain environmentally acceptable products. This paper reviews the technologies used for processing aqueous metal-chloride solutions and describes the challenges that have been overcome in application of these technologies.

Jan 1, 1993

By Sean Gallagher, Thomas G. Bobick, Richard L. Unger

This paper describes research by the Bureau of Mines on alternative materials-handling strategies for reducing the costs and incidence of back injuries in low-seam coal mines. Strategies recommended for redesigning materials-handling tasks include elimination of tasks, mechanization of tasks, and matching lifting tasks to the physical capabilities of underground miners. The report also discusses other methods that can be used by management to reduce the costs associated with back injuries. More detail can be found in Bureau of Mines Information Circular 9235 (Gallagher et al. 1990).

Jan 1, 1992