Search Documents

By P. T. Luckie

More efficient classification with a single hydrocyclone through equipment and/or operating design changes does not appear possible. However, improvement in classification efficiency by increasing the sharpness index and decreasing the apparent by-passing while changing the cut size is possible through proper staging of inefficient hydrocyclones. But feasible multistaging requires achieving the necessary material balances around the units. Because of the interactions among the units, these balances require extensive iterations. The final step before commerical installation should be a laboratory demonstration, in order to define the control algorithm required to maintain stability. However, eventually a sufficient knowledge base should be developed that will permit simulation in place of laboratory testing as well as the incorporation of a feed forward strategy.

Jan 1, 1989

By B. M. Moudgill, T. V. Vasudevan

Marine sedimentary deposits account for 80% and igneous deposits 17% of the total world output of phosphate rock. The phosphate mineral is well crystallized and exhibits a greater floatability in the igneous deposits than the sedimentary ores. Both silicates and carbonates contribute the major gangue associated with the sedimentary ores. Although removal of silica from sedimentary phosphates by froth flotation has been in practice for several decades, with the depletion of high-grade reserves, new attempts are being made to improve the efficiency of current silica removal technology and to develop new processes for beneficiation of phosphate ores associated with the carbonate gangue. In this paper, recent developments in processing of sedimentary phosphate ores containing carbonate and silica gangue are discussed.

Jan 1, 1987

By R. F. Holub, P. J. Dallimore

Basic to solving the problem of the role of radon transport on radon concentrations in mines is to establish whether it occurs primarily as diffusion and forced flow through porous rock or through fissures in the rock. The laboratory experiments performed involved measurements of diffusion and emanation coefficients, porosity and permeability of representative rock samples. Significant differences have been found when comparing the results of the laboratory permeability determinations to those of the mine determinations. Considerations of underlying principles, however, suggest that the diffusion and emanation coefficients are the same in laboratory and mine. It was also found that moisture content plays a dominant role in radon transport through rock. Using these concepts and findings, some conclusions about the radon concentrations in mines have been drawn.

Jan 1, 1981

By Alfred W. Hefferan

A longwall face conveyor system serves the primary function as all material handling systems; i.e., to transport material between the source and its destination. However, the conveyor system must provide many other functions as opposed to the traditional belt conveyor system. In this paper, we will attempt to contrast the longwall face conveyor system with a belt conveyor system. In addition, the unique problems encountered along with the solutions to these problems will be covered. Table 1 lists the characteristics required of each conveyor system. The table demonstrates the contrast in the two systems. Both must be designed specifically to encounter its unique problems. The balance of this paper will explain how the longwall face conveyor is designed to address its requirements.

Jan 1, 2000

By Hugo J. Garcia, M. C. Fuerstenau, D. M. Lupan, J. L. Hendrix

Biodegradation of cyanide by microorganisms isolated from solids previously exposed to cyanide has been investigated. The anaerobic cyanide biodegradation showed good, short-term removal of cyanide in the presence of nutrients (medium A). This system retained metabolic activity at cyanide concentrations up to 300 ppm at pH 10.5. Microscopic examination of stained specimens revealed that the bacteria were Gram-negative, rod-shaped bacilli. Strains capable of cyanide decomposition were identified as Pseudomonas and Alcaligenes. The kinetics of biodegradation were found to be first order with respect to cyanide concentration, and the overall reaction rate constant is k = 0.102 day-1. Studies with Na14CN showed that 17 % of 14C transformation went into the cells, 18 % into carbonate and 47 % into bicarbonate.

Jan 1, 1995

By Joe M. Bryan, George E. Rodger

The development of small precious metal mines in the western states has been directed at heap leach operations. Crushing plants are an essential adjunct to heap leach operations. They must meet environmental air quality regulations which generally follow a similar pattern from state to state. Prior to mine construction a permit must be obtained and an operating permit granted during or shortly after the start-up period. The typical construction permit application consists primarily of drawings, specifications and an explanation sufficient to indicate that the mass of particulate matter entering the atmosphere is below minimum standards. The operating permit may be granted following demonstrations that air emission control equipment or methods comply with information submitted in the construction permit application.

Jan 1, 1987

At periodic intervals-typically at the end of each month, quarter, and year- the accounting department in each division of a company distributes a set of reports to the division's managers. These reports describe the financial performance of the division and its major departments over the time period. They identify the revenues generated from the division's products and the costs incurred in their production. The results from individual departments are combined to determine divisional results, and the results from individual divisions are in turn consolidated to determine the results for the overall corporation. Cost reports for each of these activities show actual amounts, budgeted amounts, and the differences between the two. This reporting is carried out for the individual period and for the year to date.

Jan 1, 1999

By D. C. Torre

Since the early 1960s, there have been efforts to develop and produce reliable continuous haulage systems capable of taking the full output of a continuous miner and transporting it, in one continuous flow, from the face to the tipple. The majority of the successful continuous haulage systems were placed in operation in the early 1970s. These were all of the bridge conveyor type. They usually consisted of bridges and mobile bridge carriers (MBC) attached at the inby end to the continuous miner and at the outby end to the panel conveyor itself. These successful bridge conveyor continuous haulage systems are either of the belted or chain type. The most successful belt type continuous haulage systems are those manufactured and marketed by the Long-Airdox Co. Until early 1977, Jeffrey Mining Machinery Division manufactured and marketed the most successful chain conveyor type haulage sys¬tems. In 1977, Long-Airdox reentered the market with a chain-type system to complement its belted system. The original bridge-type continuous haulage system was introduced to the coal mining industry in the early 1960s by the old Long Co., a predecessor to the current Long-Airdox Co. These original units were of the chain conveyor type. In the early 1970s, there were also developments in continuous haulage, employing different material handling media. These in¬cluded the Serpentix, a flexible type belt, introduced by the Joy Manufacturing Co. There was also a serious attempt to introduce hydraulic-type continuous haulage by Consolidation Coal Co. and Conoco Research. Despite some startling successes, particularly with the bridge-type haulage systems, the general and widespread application of continuous haulage has eluded the mining industry. Some of the problems are related to underground conditions; others to people, both management and labor. One of the greatest obstacles to universal success continues to be the difficulty of accepting the philosophy as well as the machinery of continuous haulage. Nevertheless, efforts continue to spread the success of commercial and viable systems in the industry. There is also effort to improve on these systems, and on methods for their successful use. In addition, efforts continue, with private and public support, to develop new types of continuous haulage equipment and systems. Bridge Type System Developments Because they have already been successful in some US and overseas mines, new developments in bridge-type systems will first be touched on. The Long-Airdox Co. has continued to improve both its belted and chain continuous haulage system. In the belted system, the company recently introduced a new design that will be mainly applicable in higher coals and in noncoal mining applications, as shown in the accompanying figure. This new system is equipped with 305-mm-diam (12-in.-diam) pulleys in the bridges and mobile bridge carriers, in place of the 150-mm-diam (6 in.-diam) pulleys in the standard system. The modification is designed primarily to improve belt life and keep belt problems to a minimum. An operator, the Clinchfield Coal Co., a Division of Pittston Coal, developed the detaching of the bridge-type continuous haulage system from the miner by placing a mobile bridge carrier at the head of the string. However, Long-Airdox and Jeffrey have now made this an option to their at¬tached-type system. In the US, there are many chain type haulage systems detached from the miner with an extra MBC at the head. There are two such belted systems

Jan 7, 1982

By E. P. Fahrenthold, K. E. Gray

Introduction Brine reservoirs along the Texas and Louisiana Gulf coasts are currently under study to investigate the technical and economic viability of production wells designed to extract methane gas in solution. The effect of well pressure drawdown on reservoir rock and associated overburden material is important to well performance predictions and the analysis of potential subsidence problems. Consequently a series of compaction tests have been conducted on sandstone and shale cored from a test well drilled near Hitchcock, Texas, in order to determine the variation of mechanical properties to be expected over the producing life of the formation. Previous Work The referenced tests are part of an extended study of geopressured-geothermal reservoir behavior, including compaction (Jogi, Gray, Ashman, and Thompson, 1981 and Jogi, Kalra, Gray, and Thompson, 1981) and creep (Thompson, Jogi, Gray, and Richardson, 1981) tests of reservoir rock and related reservoir performance studies (Rago, Okhuma, Seperhnoori, and Thompson, 1985). Recent work has considered the nonlinear constitutive behavior of sandstone (Fahrenthold and Gray, 1985 and 19861, while additional experimental work is reported here. Geological structure and composition of the Hitchcock field from which the core samples were obtained is discussed by Light (1985). Experimental Procedure Compaction tests were conducted on cylindrical cores, nominally 2.75 inches in length and 2 inches in diameter, with independent control of the axial, confining, and pore pressures. Axial and radial deformation of the samples were measured in tests over a range of effective stress states expected to develop over the reservoir lifetime. The term effective stress as used here refers to the algebraic difference of the total stress and pore pressure, with compression taken as positive. Three types of compaction tests were conducted on the sandstone. In the uniaxial tests, axial total stress and radial strain were held constant as the pore pressure was reduced, similating one dimensional compaction which may occur during reservoir depletion. In the triaxial tests, radial total stress and pore pressure were held constant as the axial total stress was increased, duplicating conventional rock compaction test procedures. In the pore pressure drawdown tests, axial and radial total stresses were held constant while the pore pressure was reduced, in order to investigate differences in sample response to mechanical and pore pressure loading. Compaction tests were also conducted on shale material obtained from the reservoir overburden. The field coring process provided few consolidated shale sections sufficiently large to allow preparation of samples with the dimensions described above. With additional attrition during sample preparation of this brittle material, ultimate yield of the coring effort was limited. The few available samples were tested in uniaxial and triaxial tests similar to those described above. The use of displacement transducers to measure sample deformation avoided the difficulty of strain gauge installation on this material. Test Results The sandstone and shale both demonstrated nonlinear stress-strain behavior, with hysteresis and residual strain present upon unloading. Polynomial interpolation of the stress-strain curves was used in the calculation of incremental values for the loading and unloading moduli. Figures 1 and 2 show example axial effective stress-axial strain curves for triaxial tests conducted on sandstone and shale samples. The figures plot incremental stress and strain variables, defined as deviations from the state of prestress to which the sample was subjected. The state of prestress was varied between tests in order to investigate material behavior over the entire stress and strain space of interest. Tables 1 and 2 give the incremental moduli (Young's modulus and Poisson's ratio) as a

Jan 1, 1986

By R. C. Freas

Imported products and materials have been in the news over the last several years in a wide variety of industries. Certainly the mining and industrial minerals industry has not been exempt from this. Cement imports have received considerable attention in the press and a number of written articles. We are also seeing imported aggregates particularly along the gulf coast and east coast of the United states. We are now hearing increasing talk of bringing high brightness calcium carbonate from offshore sources into the U.s. domestic markets. This paper takes a look at the location of these sources, factors affecting their acceptance by U.S. industry and presents a general cost comparison of offshore and domestic calcium carbonate. In addition, the market response of U.S. suppliers and the impact of imports is also discussed.

Jan 1, 1989

By T. M. Gurr

It is estimated that in excess of one-half million chemicals are used throughout the American workplace. Hundreds of new chemicals are also being introduced into the workplace annually. Exposure to some of these chemicals can be harmful to workers and to the environment. The Occupational Safety and Health Administration (OSHA) estimates that approximately 25% of the U. S. labor force or approximately 25 million workers are exposed to one or more chemical hazards each year. OSHA has determined that this poses a serious problem for workers exposed to such chemicals. Chemical exposure may cause safety and health problems. Health problems can include a cause or contribution to heart ailments, kidney and lung damage, sterility, cancer, burns, and rashes. Safety hazards can include the potential to cause fires and explosions and other serious accidents.

Jan 1, 1989

By John Jonkman

During the decade of the eighties, the mining industry was able to take advantage of numerous advancements in computing technology. The development of the desktop workstation and the tremendous increase in power of minicomputers have cause many of the technical computing applications to be taken out of the "glass house", or central computing facility, and distributed to where the work is actually performed. This trend, combined with the significant price/performance improvement being experienced, has resulted in computers becoming more readily available at a reasonable cost for research and development activities, thus increasing the amount of new development taking place. The papers in this session discuss research and development work which has resulted in advancements in mining technology applications in the following areas: - Technical Parameterization - Linear Programming - Dynamic Programming - Computer Aided Design

Jan 1, 1989

By Drupad B. Desai, James G. Gallanes

A key component of the Inland Feeder Project is the Riverside Badlands Tunnel, a7.9-mile stretch subjected to high internal and external hydraulic pressures passing beneath highly eroded hills in a semi rural environment. The tunnel presented significant design and management challenges to the project team. This paper describes the formula for project success used to manage the design of this complex pressure tunnel, from team member selection to the completion of all contract documents, on schedule and below budget. The project team dealt with sensitive regional and local community issues and won the trust of the community. The team included participation by senior management and recognized experts from inception to finish. The team worked diligently to build quality into design and adopted a claims avoidance approach to management and preparation of documents.

Jan 1, 1997

By Harold Wahlborg, George Owusu

In a study using butyl diglyme as an organic extractant, essen­tially complete extraction of gold from chloride leach solution was achieved. The extraction kinetics are so fast that the process could be completed in 30 seconds. Except for iron, co-extraction of other ionic species was insignificant. Co-extracted iron species were successfully scrubbed from the loaded organic using 10% HCl solution. High grade, >99.9%, gold was recov­ered from the loaded organic using 5% oxalic acid solution as the stripping agent at a temperature of 70°C to 80°C. Over 99% of the organic-loaded gold was stripped from the organic phase. The butyl diglyme extractant is being tested on a variety of gold-bearing feedstocks. Presented here are results obtained from two gravity concentrates.

Jan 1, 1999

By Earl Sackett

In its 110-year history as a mining camp, the Boleo copper district of Baja California has weathered significant changes in its operation, ownership, and profitability, despite an inhospitable environment and unique ore body. For some 65 years, under the operation of Compagnie Boleo, the area ranked as the second largest copper producing district in Mexico, with over 560 km of underground workings. As its ore grade-and profitability-declined, operations continued sporadically and with varying degrees of success. Today, operations at Boleo are maintained -despite the economics -while work is underway to devise a viable metallurgical process. Lab tests on a hydrometallurgical method look encouraging and, though this may end the district's days as a mining camp, the feasibility of the process may result in an 18-kt/d full-scale operation.

Jan 7, 1980

By F. X. Meagher

Vertical slot raise driving from bottom up has always been a hazardous, inefficient, high cost operation. The introduction of the Simba 5 drill rig has enabled this type of raise to be drilled accurately from the top down and to be blasted in stages from the bottom up. Safety, high efficiency and low cost were the main criteria in opting for this method. Drop raises with the Simba 5 at Geco have been successfully drilled and blasted up to 115 feet, and this is close to the maximum length of raise that can be drilled and blasted efficiently with Simba 5. A look into the future would indicate a rig capable of drilling up to 200 foot raises with the same accuracy of Simba 5 to 115 feet.

Jan 1, 1974

By Robert Roggenthen

In 1994, ASARCO's Mission Complex Mine Planning Department designed a new stripping schedule to take advantage of reserve opportunities. Based upon the new stripping design, overburden removal exceeded available hauling capacity. This increased hauling capacity requirement required that ASARCO consider alternative technologies for material transport. In 1997, ASARCO Mission Complex completed the purchase and installation of a 3.5 km, 8,600-tph conveyor system to transport waste material. The conveyor system is composed of two apron feeder/sizer units manufactured by Mining Machine Development LTD. and a conveyor system manufactured by Krupp-Robbins. This paper will review the option of truck haulage versus conveyor transport for overburden removal by (1) describing engineering studies contributing to the solution, (2) researching proactive options to create alternative management decisions, and (3) revealing final results of the project.

Jan 1, 1998

By James P. Rider, Robert P. Vinson, Fred N. Kissell, Jon C. Volkwein, Gregory J. Chekan, Jay F. Colinet

The Thermo-MIE personal DataRAM dust monitor (pDR) is a light-scattering instrument approved for use in gassy underground mines by the U.S. Mine Safety and Health Administration (MSHA). However, the use of lightscattering monitors has been inhibited by concerns about inaccurate readings resulting from changes in dust size distribution and composition, as well as concerns about the impact of moisture in the mine air. Because of this concern, the National Institute for Occupational Safety and Health (NIOSH) has evaluated the pDR using available data from laboratory tests and mine surveys. The data show that accuracy can vary widely from test to test and mine to mine. In most cases, the results can be improved by using a companion gravimetric measurement to adjust the pDR data.

Jan 1, 2005

By G. Bezuidenhout

The newly developed Bateman Flotation Machine has proven its versatility in roughing and cleaning flotation circuits. This mechanical flotation machine has the dual performance capability of suspending solids and dispersing air at relatively low power inputs without compromising these two important fundamentals. This new development has been successfully marketed to a wide cross section of concentrator mineral processes. The mechanical design of the flotation mechanism has been optimised to reduce operational costs and to lower manufacturing costs. Production process environments were utilised for verification of the scale-up of each cell volume size rated mechanism. These thorough investigations produced performance data which could be accurately quoted. This paper is a historical account of the Bateman Flotation Machine. Technical details of the development are covered with descriptions of the operational applications.

Jan 1, 1995

By Steven W. Hunt, Phillip U. Santacroce, Roger C. Ilsley

Consolidation grouting from the surface prior to mining a shaft is commonly performed to reduce groundwater inflows to a manageable rate. This paper describes the inflow reductions obtained within dolomite and limestone formations at several shafts and chambers due to grouting programs for the Milwaukee Water Pollution Abatement Program. The resulting inflow reduction factors are compared to results reported in the literature for other projects. Post-grouting pump tests are also evaluated as an aid in grouting assessment. Important considerations for estimating shaft inflows from pump test results are discussed. These considerations include loss of grouted mass during mining and influence of blasting and rock features on grouting effectiveness. This information should be helpful to design engineers and contractors who need to estimate inflows after pre-excavation consolidation grouting has been performed.

Jan 1, 1993