Search Documents

By E. S. Smith, Sunirmal Banerjee

INTRODUCTION Social awareness of the detrimental impact of man-made wastes on our environment has grown considerably during the last two decades. Increased public and institutional concerns have resulted in the implementation of a wide variety of regulatory controls of disposal of wastes. These regulations have often reflected significant conservatism in expecting guaranteed elimination of pollution risks. This sort of expectation assumed a state of knowledge which was not readily available to the major producers of wastes. The mining industry, in particular, has been affected by such regulations in terms of excessive costs and loss of benefit. As a result, investigations are in progress (1) to generate newer methods for satisfactory stabilization of mine and mill wastes and (2) to apply the available technology to achieve the standards set by the regulatory agencies at reasonable costs. This paper presents a conceptual scheme for stabilization of mill wastes by suitable management of operations and accelerated consolidation of tailings slurries. The main discussion in this paper is aimed at the ability of the proposed scheme to address the major considerations in effective disposal. Comparison in both cost and effectiveness are also made between the proposed scheme and various other currently used disposal concepts. MAJOR CONSIDERATIONS IN EFFECTIVE DISPOSAL The primary objective of an effective tailings disposal scheme is to provide containment of the contaminants in such a manner that the undesirable impact of the wastes on the three basic elements of our environment--land, air, and water-would be minimal. Bearing the above objective in mind, one may justifiably list the major considerations in the choice of the disposal scheme in terms of its effects on land, air, and water (Bromwell, 1976) as follows: Effects on Land (1) whether the scheme makes optimal use of land.

Jan 1, 1980

By E. P. Evert

Profitable marketing of most minerals is dependent upon the total delivered cost to the user. Transportation costs are often greater than the value of the mineral f.o.b. the mine or processing facility. In some cases, transportation costs are three to five times the mineral cost. For many years, transportation costs were controlled by a complex system involving the transportation companies and supervised by regulatory agencies. This paper will deal with the effects of deregulation on rail costs and outline the major changes in transportation economics.

Jan 1, 1985

By J. W. Jang

The wear behaviors of grinding media with different chemical compositions and microstructures in wet grinding of a quartz-pyrrhotite mixture was investigated under various environments. The marked ball wear tests showed that the wear rate could be minimized by a suitable combination of martensite and ferrite within the same ball. A ball composed solely of hard martensite exhibited increased wear under an oxygen environment, while balls composed of both soft ferrite together with hard martensite exhibited decreased wear due presumably to the difference in their passivation? behaviors. The galvanic interactions between the two phases as well as among these phases and an electroactive mineral were investigated through electrochemical measurements under abrasive conditions in a slurry. The rates of formation of passive films controlled the corrosion currents of the high chromium steel media. Corrosive wear and its effect on flotation are discussed using the passivation kinetics model thereby developed.

Jan 1, 1989

By Michael J. Martinson

Mine ventilation has been evolving as a separate field of study since the middle of the nineteenth century, and some practitioners might assert that mine ventilation has come of age as a discrete field in the last decade or two. Certainly the extensive literature now available on many facets of the subject, international congresses, the phenomenal upsurge of interest in mine ventilation in the United States of America since the passage of the 1969 Federal Coal Mine Health and Safety Act, and the existence of a virile mine ventilation society in South Africa with its own monthly journal all point in this general direction; on the other hand the lack of a rational design philosophy for ventilating mines suggests that mine ventilation may still be on the threshold of maturity. To generalise, many mines are still ventilated simply to comply with arbitrary statutory regulations, or with some ill- defined notion of reducing the risk of injury associated with the atmospheric environment in mines. Hazards in this category include oxygen deficiency, toxic gases and particulates, pathogenic gases and aerosols, explosive gases and dusts, and extreme climatic conditions. Although many mines are ventilated to abate the risk of a specific injury, there is inevitably a spectrum of latent and patent atmospheric hazards in every underground mine. The writer (Martinson, 1976) has previously drawn attention to the dearth of material on mine ventilation design in textbooks and technical journals, and to the overly simplistic approach sometimes adopted in the limited work published on the subject. The available material undoubtedly contains useful technical data and persuasive views, but seemingly could not be used to demonstrate the rational engineering approach to mine ventilation design advocated in the present paper. The range of papers presented at the 1975 and 1979 Congresses, and the diverse interests and affiliations of delegates, emphasize the multidisciplinary nature of mine ventilation. Easily recognisable topics include: Fluid mechanics Thermodynamics Heat transfer Flames and combustion Aerosol physics Radiation physics Geophysics and geomechanics Occupational diseases Epidemiology Industrial physiology Despite these heterogeneous connections there can be little doubt that mine ventilation is fundamentally an engineering field and not an off-shoot of some other branch of applied science. The distinction is important because mine ventilation has essentially developed as a form of ad hoc trouble- shooting, and in the process mining engineers have relied extensively on the assistance of experts drawn from other fields. Thus historically there has been limited scope for the application of rational design techniques, and personnel enlisted from scientific disciplines may not have had any previous experience in the intricacies of engineering design.

Jan 1, 1980

By Dan Xu, Song. Gaofeng, Zhen Wei, Zhihe Wang

"With decades of development and exploitation of coal resources, the first batch of coal-based cities in China are faced with the challenge of economic shrinkage and environment deterioration due to the rapid resource exhaustion and single industrial structure. Nowadays, as a policy instrument for sustainable development, a nationwide circular economy mode has been implemented during the design and planning of new coal mines to address the challenges arising from economic depression, energy shortage and environmental pollution. It should be mentioned that several national coal bases and most of constructing and planning coal mines are located in the underdeveloped areas in the Midwest of China which means that the distance between supply source for energy resources and the demand market is significantly increased. Moreover, the eco-environment vulnerability in these rural areas should be taken into serious consideration. Therefore, after comparison and analysis with several successful coals based and diversified circular industry chains, this paper presents a case study on the circular economy park (CEP) in the northwest of Shanxi Province. Through discussion and evaluation of ‘1+3’ mode in the CEP, this paper aims to enhance the understanding of coal mine sustainable development and shed light on the relationship between resources exploitation and local economic development.1. Introduction Earth's fossil energy resources are crucial to both economic prosperity and human well-being. Taking coal mining and consumption as an example, coal has been widely used to generate electricity since the 1880s, and more than 40% of the electricity globally is provided by coal nowadays. However, as one of the largest worldwide anthropogenic sources of carbon dioxide releases (39% of global CO2 emissions), the extensive excavation and utilization of coal have brought a series of side effects to both natural environment and human health (Wikipedia 2017). As the largest coal producer and consumer in the world, China is leading the list over the past decade (as shown in Figure 1) (BP 2016). The excavation and utilization of coal resources have made a crucial impact and irreplaceable contributions to China’s industrial development and economic prosperity (Long and Zhang 2009). However, most of the air pollution in China are also attributed to the simplified and extensive exploitation of coal resources, e.g., 90% of SO2, 67% of NO, 70% of smoke ashes, and 70% of CO2 in 2016. In recent years, most of North China and the developed coastal areas were wreathed by smog due largely to the oversimplified extensive utilization of coal, suggesting that the development patterns of coal utilization need to be reshaped so that both the biosphere and humanity could thrive equally."

Jan 1, 2017

By C. E. Capes

INTRODUCTION In the coal industry, ever greater amounts of fine coal must be processed due to the need to crush to finer sizes for impurity liberation in low cost physical cleaning processes. Fine coal processing is a major problem for the industry, both through the cost of disposal of reject fines and through the mining cost of lost coal values. Of the available disposal methods, impoundment has always been the most popular. In many cases, when the coal fines were of sufficient quality, froth flotation and expensive filtration methods were used to recover the coal in these waste streams. The coal fines are not always of a marketable quality, however, and flotation, due to poor yields and difficult dewatering, has always been an expensive and not necessarily profitable process. The oil agglomeration method is increasingly important as a technology for the treatment of fine coal-in-water suspensions. These fines can be preferentially wetted and agglomerated by many different oils mixed with the suspensions. Ash-forming impurities remain in suspension and are rejected when the agglomerates are recovered, for example, by screening. Agglomeration-based methods provide perhaps the only practical means for upgrading extremely fine coal to useful products on a large scale. As with froth flotation, oil agglomeration relies on differences in the surface properties of coal and impurities to effect separation. Whereas flotation be- comes less effective with particles finer than 200 mesh (0.075 mm) or coarser than 50 mesh (0.3 mm), there appears to be no lower limit on particle size for oil agglomeration while particles % in. (3.175 mm) diameter or larger can also be treated, if desirable. In addition to this ability to clean a broader size range of coal particles, oil agglomeration can produce a dense, coarse granular product of acceptable strength and low water content without the need for vacuum or thermal drying. The preferential wetting of solid surfaces by immiscible liquids has been utilized, if not fully understood, for a long time. Indeed Gaudin,229 in tracing the ancestry of froth flotation, refers to a 15th century oil-pulp kneading procedure in which water-wetted particles were freed under water from an oiled mass. An understanding of the physical chemistry involved in such

Jan 1, 1991

By Andrzej M. Wala

A prototype expert system for planning and designing an underground coal mine has been developed in a doctoral study at the University of Kentucky. This prototype expert system for underground coal mine planning and designing consists of a number of knowledge bases concerning different elements of design (e.g., ground control, excavation and bulk materials handling, ventilation, etc.). The objective of this paper is to present the development process of the ventilation design knowledge base for this prototype. This expert system prototype is intended for building an instructional expert system for underground coal mine design. Therefore, the undergraduate course on mine design has been used as the basis, for its development. Because of the availability of knowledge and expertise, this research study has been limited to development of a knowledge model for the Appalachian coal mining region.

Jan 1, 1993

By R. J. Wesely, Corby G. Anderson, L. Ernest Krys, John B. Ackerman, A. D. Zunkel, Suzzann M. Nordwick

Processing of the refractory precious metal ore from the Sunshine Mine is done in a fully integrated hydrometallurgical facility. This operating philosophy began with the construction of an antimony plant during World War 11, and it continued with the construction of a silver-copper refinery in 1984. The antimony plant relies on an alkaline sulfide ambient pressure leach combined with antimony electrowinning and antimony compound production. This plant is the largest producer of antimony metal in the United States. The one-of-a-kind silver- copper refinery uses a nitrogen species catalyzed sulfuric acid pressure leach system. The plant contains innovative downstream silver recovery processes as well as copper solvent extraction and electrowinning. This paper presents the pertinent process chemistries and flow sheets for the two unique hydrometallurgical processing plants.

Jan 1, 1993

By W. Jacobi, K. Eisfeld

The primary objective of dosimetric modelling for the inhalation of radon daughters is the evaluation of the dose distribution and of the mean dose to sensitive cells or target tissues in the respiratory tract which are assumed to be responsible for the initiation of lung cancer. The results of such dosimetric models are influencing the practice of radiation protection in a twofold manner: Firstly, they enable us to identify appropriate operational quantities for air monitoring and for the surveillance of individual exposures to radon daughters. Secondly, they can be used to derive secondary and operational limits for these radionuclides from the basic dose limits. The dose to target tissues in the lung from inhaled radon daughters depends on various physical and biological parameters: The unattached fraction of daughter atoms, the AMAD of the carrier aerosol for attached atoms, the geometry of the respiratory airways, the breathing conditions, the parameters for the retention and translocation of daughter atoms in the different lung regions, and the location of the target cells or target tissues, respectively. Therefore, dosimetric modelling for radon daughters has to include a sensitivity analysis showing the influence of these parameters. To meet these objectives we have recently described in a comprehensive report an improved dosimetric model for the inhalation of 222Rn, 22ORn and their short lived daughters (Jacobi and Eisfeld, 1980). In the following this model is shortly described and the main results are summarized. DOSIMETRIC MODEL [Model Structure]. For the geometry of the bronchial airways the model A of Weibel (1963) was used. Each bronchial generation i (i =0.1 .... 16) was considered as a separate compartment i, for which the following transfer pathways for radon daughter atoms were taken into account (see fig. 1): (1) the uptake by deposition (deposition probability wi); (2) the translocation by ciliary clearance (rate constant [A]i); (3) the transfer to blood by diffusion through the bronchial epithelium (rate constant [A]b). To distinguish between attached (Index a) and free (index f) daughter atoms each bronchial generation was divided in two subcompartments (i.a and if) with a transfer rate constant [a]s (ia- if) characterizing the desorption or dissolution rate of attached atoms in the mucus fluid. Thus for daughter atoms primarily deposited in attached form the transfer to blood is a twostep process with the rate constants [a]s and [A]b which were assumed to be independent of the generation number i. [Deposition]. The deposition probabilities wi in each bronchial generation were calculated on the basis of the laminar diffusion model of Gormley et al. (1949); however the deposition in the upper airways was corrected for turbulent air flow, taking into account the results of our deposition experiments (Martin et al., 1972). Figure 2 shows the resulting deposition probabilities per unit surface area of the bronchial generations for nose breathing at a rate of 20 1/min. The values for attached daughter atoms refer to an AMAD of 0.2 - 0.3 µm ([O]g =3) for the carrier aerosol; the deposition values for free atoms were derived with a diffusion coefficient of 0.05 cm2/s, assuming a prefiltration of 50% in the naseopharyngeal region.

Jan 1, 1981

By F. N. Kissell

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined-out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a longwall operation that uses ventilation to carry off hazardous gases, and two are room-and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases, employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1987

By Eric C. Schwamberge, Clem A. Pelletier, Deborah L. Muggli, George W. Poling

The Pit Lake at Island Copper has evolved into a 3-layered meromictic system. Acid Rock Drainage (ARD) is collected and injected into the lake at 220 m depth via 2 diffuser systems. In situ dye studies were conducted during 2 differing hydrological regimes in order to determine the behavior of the ARD plume within the Pit Lake. Results indicated that when runoff from the waste dumps was low, the injected ARD remained within the bottom half of the intermediate layer of the Pit Lake, initially below depths of 90 m. However, when runoff from the waste dumps was high, the injected ARD at -220 m depth rose through the intermediate water column layer rapidly, but did not breach the top pycnocline at -10 m depth. Overall, the system is currently performing as a mixing bowl with a strong boundary or cap at the upper pycnocline. maintaining mixing below the 10 m depth water level.

Jan 1, 2000

By J. P. Vandenhoeck

Sizing devices used commercially are unfortunately not 100% efficient, the splits that can be obtained are usually inferior to the results obtained in the laboratory. Often the capital and operating costs of equipment capable of high sizing efficiency cannot be justified by the economics or requirements of the process. To reconcile the desired sizing efficiency needed to obtain optimum process requirements with the sizing efficiency of equipment economically practical, it is often necessary or desirable to predict the gradation and weight splits of the products obtained based on the expectant efficiency of the contemplated sizing device or method. The less efficient the sizing device one must employ, the more important it is to know the results that may be expected for the establishment of the optimum flow sheet and the more difficult it becomes to estimate the results accurately. Air classification equipment which sizes materials by opposing the drag force created by an air stream acting on a particle with a combination of gravitational, inertial or centrifugal forces are substantially less efficient than, for example, a laboratory sieve analysis. Air classifiers allow oversize material to contaminate the fine fraction and leave undersize material in the coarse fraction. The techniques employed to predict the gradation and weight splits obtained from air classification outlined below are adaptable to other sizing devices less than 100% efficient such as screens, sifters and wet classifiers.

Jan 1, 1965

By C. O. Brawner, A. Bellamy, D. S. Cavers

Pit slope designs at Nickel Plate Mine have used relatively steep interim and final wall slopes of 60 degrees overall. The rock is unusually strong and tough with most discontinuity sets being steeply dipping. An integrated program of monitoring and drainage has been used. Stopes of large extent which are generally unsupported occur on the property. For the most part, no deterioration of the stability of the stopes has occurred over the last 30 or more years. Mining methods through these areas have used a combination of fill s placed via VCR drop raises and crater blasting of the backs. One of the major challenges in mining through the stope areas is to maintain slope stability conditions and to reduce dilution of the higher value ore zones occurring immediately around the stope areas. The paper discusses geology, slope stability and mining methods at Nickel Plate Mine.

Jan 1, 1988

By M. G. Ayat

In the previous work (1,2), initial developments in a novel tracing technique employing specifically prepared trace particiles were fully described. The synthetic tracers produced proved to represent coal particles in specific gravity based coal washing equipment in this work, a detection system has been developed that can detect the artificial tracers in the product or refuse part of the density-separating coal cleaning units and thus indicate the performance characteristics of the circuit. This system could not only be a simple, accurate, and inexpensive replacement for the usual time-consuming washability analysis, but it could also be used for diagnostic purposes in coal separatory devices.

Jan 1, 1987

By M. P. D. Ingunza, Júnior Santos, F. S. D. Araújo, A. L. C. Araújo, J. Y. P. Leite

Wastewater sludge is a problem for environmental control and it is necessary alternative researches for its reuse. Industries can research the association of clay and sewage sludge as a source of ceramic mass. This procedure can contribute for the industry sustainability including in its raw materials, wastes of environmental concern. This paper presents the results of sewage sludge and clays characterization being analyzed particle size distribution (sedimentation), mineralogical (X-ray diffraction), chemical composition (X-ray fluorescence), thermal analysis, density, and Atterberg proprieties (liquid and plastic limit; plasticity index) and also their applications in ceramics. Results were used to determine moisture for mass of raw material and sewage sludge and there were realized tests of fired in kiln at temperatures used in ceramic industry for bricks production. In the test pieces were analyzed the properties for application as bricks.

Jan 1, 2005

By Stanley Dempsey

INTRODUCTION The mining industry has been under- going a significant restructuring for the past several years. Some firms have been liquidated. Some have been merged with other firms. A number of mining divisions of larger firms have been spun off, in some cases in leveraged buyouts by management. Recently, there have been a number of spin outs of gold subsidiaries. There are also a number of start-up situations where new firms are emerging as significant gold producers through mine development or acquisition. This restructuring has created an attractive market for specialized mining finance firms, and a number of firms have recently entered that field in the United States. These firms provide financial advisory and valuation services to mining firms and project developers, and access to venture capital. In some cases, they invest for clients or for their own account. I have been asked to describe how our firm works, and what kind of information we expect to receive when mine developers seek our assistance in financing a project. HOW WE OPERATE Denver Mining Finance works for both mine developers and investors. We also provide expert advice on mining issues to governments and to firms who are in litigation over mining issues. A lot of our work involves valuing mineral interests for various purposes. Our principal expertise is in the technical, commercial, and financial area. We help put mining deals into shape commercially so that they can be financed, and we help investors get into mining deals that are commercially sound. We work on projects, but we also advise mining firms on the structure of their business and how to make the most out of one or several mines that they might own. In addition to our work for clients, we are also prepared to invest in mining projects for our own account, and to recommend gold properties for acquisition by our parent company, Royal Gold, Inc. We are, to some extent, a venture capital firm, in that we sometimes work with projects that are not "bankablerV1 and are prepared to invest in attractive early-stage situations in mining. However, I want to emphasize that our principal focus is on development of commercially attractive mining projects that can be brought into production in the best possible financial terms. If we can make a project qualify for a project loan from a commercial bank, we will not advise the developer to use high cost venture capital. For the purpose of this paper, I will focus primarily upon our functions with respect to development of precious metal projects. In a typical case, a firm with an advanced-staged project approaches us for help with financing the final feasibility study, and construction and operation of a mine. In some cases, the developer has already developed a financing plan and wants only our access to investors. If we agree that the project is sound and that the financing scheme will be attractive to investors, we will help the developer reach investors on a commission basis. In such cases, we are particularly insistent that the financing plan and our participation meet all regulatory requirements, particularly compliance with state and federal securities laws. In most cases, however, the developer asks us for advise both on how to structure the financing, and how it can be implemented. Here we work for fees based on hourly rates for advisory work,

Jan 1, 1987

By Robin G. Adams

The market prices received by producers of internationally traded commodity metals have been, and continue to be remarkably volatile and unpredictable compared with most other traded goods and services. This volatility results in an erratic financial performance on the part of producing companies, disruptive and often inflationary cost changes for consumers, unreliable tax revenues and export earnings for host governments and severe social and economic pressures on local, sometimes remote, communities which are dependent on the activity in question. Generally speaking, price volatility appears to be associated with the inability of the metal producing side of the industry to regulate the volume of supply in a manner that is consistent with metal demand, which in turn reflects broad macroeconomic and industrial developments around the world. This statement does not purport to apply to all metals or to all instances of volatility of course. Price movements may occur as a result of pure speculation or even illegal manipulation of the commodity markets. Embargoes, boycotts and other politically induced supply changes may contribute. Threatened or actual strikes also cause artificial swings in sales volumes and prices. How- ever, most of these developments are of a short-term nature. Yet metals price cycles may last for several years, as demonstrated by the extended copper price trough from 1981 to 1986. This paper deals with price volatility which reflects long-term economic cycles and the adaptive processes that exist within the industry in response to such cycles. Special emphasis is placed on the role of forecasts and forecasters in these processes. It should be said at the outset that this reflects the personal experience of one forecaster working in private sector commercial consulting practices that are independent of producers, consumers and host governments. However, the experience does cover the entire period since 1973 and has involved working with a substantial majority of the major companies that supply high volume commodity metals. By way of background it should be stated that the post-1973 world economy has provided a challenging environment for forecasters. One cannot be precise about the forecasting record of either industry insiders or outside consultants, financial analysts and academic forecasters because comprehensive records have not been kept, or if they have the results are too embarrassing to be published. Institutions such as the World Bank have published forecasts of the prices of major commodities on a regular basis and these have, presumably, had some influence on financing decisions in the industry. This record along with our own experience and numerous discussions with metal producers, major consumers and host governments permits certain generalizations to be made. The most important of these is that during the early 1980s. from about 1980 through 1985/6, the forecasters system- atically and substantially over- estimated metal prices. While some fore- casters did correctly anticipate a recession in the early 1980s and some consequential decline in prices, the magnitude and duration of the decline was far greater than anyone foresaw. This systematic forecasting "failure" appears to have occurred independently of the forecasting methodology employed. Moreover, its extent cannot be explained by obvious factors such as incorrect macroeconomic assumptions. There appears to have been some kind of structural change in the world mining and metals industry over this period

Jan 1, 1989

Stratabound uranium deposits consist generally of two comingled geologic and statistical populations. Barren zones, usually having radiometric assays too low for recording on digitized logs, comprise a large portion of a mineralized stratum. In between are mineralized zones; where the grades are distributed essentially lognormally. Estimation of open-pit ore reserves requires the prediction of the tonnages of selective mining units (the smallest mined volume which may be segregated as ore or waste) and their grades within panels of convenient size for open pit planning and economic analysis. The proportionate tonnage of mineralized selective mining units within each panel can be predicted by kriging an an indicator function assigned to each composite (1 if mineralized, 0 if barren). Next, using logarithms of mineralized assays, the conditional lognormal distribution of grades of mineralized selective mining units can be found. Using this distribution and the krigedestimate of the probability a selective mining unit is mineralized, the grade and tonnage of selective- mining units above any cutoff can be predicted. A case study illustrating this two- step procedure is presented for the Imouraren uranium deposit located in the Republic of Niger. Using cross validation, the estimation procedures were checked and were shown to be adequately accurate for mine planning purposes.

Jan 1, 1979

By V. K. Kollipara

Dust dispersion characteristics in mine airways are important for developing engineering controls for dust and explosions. Authors here have used CFD modeling approach to analyze the dust dispersion characteristics in mine airways. The technique was initially validated with the published field experimental data. The results obtained were in a reasonable agreement. CFD validation results show that in a single entry the dust concentration decreases exponentially as a function of distance. Finer particles can travel up to a distance of 350-400 m away from the source. Parametric studies indicate that air velocity and input dust concentration has significant influence on dust concentration distribution. CFD modeling was then applied to study the dust dispersion characteristics in a room-and-pillar mine layout. Preliminary results show that dust concentration distribution is highly dependent on the airflow patterns and air velocity distribution. The distribution is not exponential until the velocity in the travel way becomes uniform. Data developed in this study may be used to design mine layouts and engineering controls for dust control and explosions.

Jan 1, 2011

By Jerry Motz, Gary Beerkircher

Through a joint development program between Bougainville Copper Ltd. and Nordberg, the MP1000 cone crusher was developed and tested during the period between 1982 and 1987. Following the successful prototype work, Bougainville Copper purchased an additional three units. A second prototype was installed at Codelco's El Teniente three-stage crushing installation in 1987. This unit has also completed its test period successfully. Three additional units have been sold, making a total of eight, to date. Two will be installed as secondary crushers in two separate large aggregate plants. The first unit installed in the United States was placed in operation at Vulcan Materials Company's plant in Manassas, Virginia in early May 1990. Another unit is being installed in Asarco's Ray Mines expansion. The Asarco installation will be a SAG MILL pebble crusher producing approximately 600 STPH of nominal 1/2" product. Application Objective The objective was to design a crusher that would fit on an existing 7' foundation with minimum modification and yet be capable of twice the production of a 7' cone crusher. In meeting this objective, the power rating was increased to 1000 HP, the maximum design crushing force was increased and the crusher was designed to operate at higher speeds than an equivalent size Symons cone crusher. The MP1000 was also designed to operate with a head throw that can be greater than the equivalent Symons design. Design The crusher design criteria involved the recognition of the crushing force increase required for the finer crushed products than

Jan 1, 1992