Search Documents

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines showed that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum group metals (PGM) was technically feasible. This work involves a more detailed investigation of the chemistry of the dissolution of PGM in cyanide solutions. The PGM species in solution identified by ultraviolet spectroscopy. Pt and Pd cyanide complexes were square were The planar in geometry, while the Rh complex was octahedral. The rate of dissolution of the PGM was also investigated using a rotating disk technique. Dissolution rates increased in the order of Rh, pt, and Pd, respectively.

Jan 1, 1994

By Randall E. Hughes, John F. Burst

This chapter describes the nature and occurrence of the principal clay minerals that are used as ceramic raw materials, explains how these raw materials are used to produce finished goods, and summarizes positive and negative trends that will affect future demand for raw materials and products in the ceramic industry. The term ceramics was derived from the ancient Greek keramikos (a clay jar). A ceramic product is a material that has been fired to at least 468.3°C (Mitchell, 1983). In addition to being one of our earliest manufacturing and construction materials, ceramic products are among the earliest records of civilization. The enduring significance of ceramics is shown by the fact that, even today, the manufacture of whitewares, brick and related red-fired wares, refractories, and engineered ceramics continues to be a major sector of the US economy. A wide range of materials can be made into ceramic products, although relatively few earth materials make up most of the ceramics in today's markets (Table 1). Most ceramic products are made from clay or a related material. The long history of clay use in the ceramics industry stems from its variable and sometimes unique physical and chemical properties, as well as its ubiquitous occurrence and relatively low cost. Clay is important to ceramics because of its plasticity, moldability and filterability, chemical content, color. refractoriness, solubility. corrosion resistance, electrical properties, and other properties that result from the essentially two dimensional morphology of the individual clay mineral platelets. Because of their basic relationships to the chemical and physical properties of clays, the chemical and mineralogical content have been the subject of continuous studies over the past few decades. Advances in knowledge about the chemical, mineralogical, and physical properties of clays are responsible for most of the advances in processing. The need to remove off-colored contaminants, minerals with low melting points, and soluble salts has resulted in beneficiation by wet processing methods such as water washing. Water washing is restricted to kaolins, although low cost methods of water washing have been extended more recently to ball clays in Europe. High intensity magnetic filtration and flotation technologies have noticeably improved the quality of kaolins and broadly expanded their use in the ceramics industry. In addition to products for construction (e.g., brick, tile, sewer pipe, field drain pipe, cement, fiberglass, roof granules, and paint) and manufacturing (e.g., refractories, kiln furniture, sanitary ware, pottery, and dinnerware), clays are used in calcined form as ceramic fillers, carriers, extenders, and grogs. Ceramics suppliers are under economic pressure in several of these product areas. Manufacture of refractories in America has declined as steel production has decreased. Similarly, dinnerware and tile production have declined because of foreign competition. Fortunately, new uses for clays,

Jan 1, 1994

By R. W. Ballmer

Bingham Canyon lies in the heart of the Oquirrh Mountains, 25 miles southwest of Salt Lake City, Utah. In it is located the world's largest open-pit copper mine, owned and operated by the Utah Copper Division of Kennecott Copper Corporation. From the beginning of open pit mining operations in 1906 until 1963, the pit haulage, or materials transportation, was primarily by rail. In 1963, phase-in of a truck haulage system in the upper two-thirds of the pit was begun. The details of that conversion, its associated problems and the resulting pit operation have been covered in an earlier paper.1 The purpose of this paper is to discuss various factors for consideration in transportation system selection, and to discuss some of the alternatives considered prior to making the change from rail haulage to truck haulage for a portion of Bingham Canyon.

Jan 1, 1968

By George H. K. Schenck

INTRODUCTION Boom-type miners mechanize the cutting and loading of a solid face of rock having a compressive strength as high as 124 MPa (18,000 psi). These machines differ from continuous miners in that they can cut much harder rock for any given cutter-motor power. In addi¬tion, a boom miner is more flexible, selectively cutting any cross-sectional configuration from circular to square arched faces, 1.57-rad (90°) turns, and mixed faces. The basic operational concept of these machines, utilizing a rotary cutterhead mounted on a slewing boom, gained importance in Europe during the 1960s, where, due to their specialized use in roadway development in coal mines, they were called roadheaders. Along with continuous miners, boom miners share the ability to fully mechanize the cutting and loading of rock, while eliminating the need for explosives and the shattering and overbreaking of roof and rib rock that is normal with conventional mining methods. The machines are crawler-mounted and most have a gathering-arm load¬ing system that, moves the cut rock onto an internal chain conveyor, subsequently discharging the rock into a transport device such as a shuttle car or a bridge conveyor. Light- to medium-weight boom miners are cutting softer rocks and minerals successfully, including coal, shale, rock salt, potash, phosphate, weak sandstones (e.g., those associated with uranium ore), and other softer ores such as iron. Heavy third-generation ma¬chines have extended rock cutting to much harder ores such as borate, oil shale, and almost all rock associated with coal seams, except for the harder sandstones and limestones. The mention herein of specific manufacturers, brand names, or models is made by way of example only and does not constitute endorsement by the author or The Pennsylvania State University. All costs cited herein are in 1977 US dollars. TYPES OF BOOM MINERS All boom miners utilize drag bits fixed on a rotary cutterhead that is powered by an electric motor mounted in the slewing and elevating cutter boom. The cutter¬head is either a ripping or a milling type, and the machines have evolved through three generations (Boldt, 1977). As shown in Fig. 1, only one boom miner cur¬rently produced can use both ripping and milling cutter¬heads on one machine. Table 1 lists boom-miner models built in large num¬bers and/or successfully used or marketed in North America. Table I excludes machines of which only a few have been produced and none sold in North America, such as those manufactured by Demag, Eick¬hoff, Paurat, and Thyssen-Rheinstahl. The only Ameri¬can boom miners are the F-16 and Super ROC¬MINER"', manufactured by AEC, Inc., State College, PA. Machine Generations Three generations of boom miners can be distin¬guished according to their times of introduction, their rock-cutting abilities, and their weight classifications. Fig. 2 illustrates typical best-practice production rates possible from boom miners for selected cutter-motor power sizes (other power figures can be interpolated). Productivity is related directly to the energy applied to the cutterhead and indirectly to machine weight; higher

Jan 1, 1982

By John P. Capp

In recent years limited markets have been developed for fly ash, the dust removed from coal-burning powerplant stacks, but most of it is still dumped in spoils areas at a cost ranging from 20 cents to $1.75 per ton. Aside from this cost, the creation of huge spoils areas can present a considerable aesthetic problem. Since the present annual fly ash output of about 20 million tons will probably reach 30 million by 1970, and because satisfactory disposal areas are becoming more limited, markets for much larger quantities of the waste are needed to keep disposal costs from becoming a significant economic factor in coal-burning powerplant operation. Current stress on air-pollution control and beautification, plus the vital need for good powerplant economy, makes it imperative, therefore, that coal producers and consumers expand markets and develop new applications for fly ash. Markets for established uses can be increased by making a greater effort to sell fly ash. New large tonnage markets for fly ash should be sought via more intensive, coordinated research. The economics of fly ash utilization underscores the vital role that must be played by research. To be competitive with other products, processes for the conversion of fly ash into marketable materials face difficulty in regard to two important economic factors--transportation cost and product utility--the other economic factors are favorable. Raw material costs of fly ash, for example, are quite attractive, and supply is no problem because there are many coal-burning powerplants in operation and many more are planned. Demand for products made from fly ash will grow if their utility is established and a good sales program is initiated. The major problems then are transporta¬tion costs and development of useful products.

Jan 1, 1966

By Darrell V. B. . McClarty

In 1996, Rio Algom, Denison Mines and the Elliot Lake Research Field Station (ELRFS) formed a consortium to implement a regional environmental information management system (REIMS) for the Elliot Lake area in Ontario, Canada. ELRFS is an affiliate of Laurentian University in Sudbury, Ontario, The discovery of uranium in the Elliot Lake region in post-World War II led to the development of 12 mines and 11 associated mills between 1955 and 1958. During the late 1980s, declining world demand for uranium, combined with the discovery of high-grade uranium ore in other areas of the world, made the Elliot Lake mines uneconomical. As a result, all area mines ceased opera¬tions by the end of 1996. The eight facilities and three tailings management areas operated by Denison Mines and Rio Algom's five mining waste management areas contain 150 Mt (165 million st) of potentially acid-generating tailings. The areas cover 13.2 km2 (3,265 acres) and receive drainage from an additional 13 km2 (3,212 acres). The primary objective of the joint initiative was to implement a personal-computer-based, regional, environmental-information management system for managing historical data and ongoing environmental programs in the Elliot Lake region. The Elliot Lake consortium decided it needed an information system with an integrated, process-oriented and requirements-driven approach to collect and manage the environmental information. Following a study of environmental information management systems currently used by the mining industry, the consortium decided to base REIMS on the "Envista" product. This is a commercially available, environmental information management system marketed by Envista Technologies of Saskatoon, Canada.

Jan 1, 1999

By Howard M. Graff

The Inland Steel Company operates five underground iron mines in the Lake Superior District. The two largest of these, from the standpoint of productive capacity, are the Sherwood Mine in Iron River and the Bristol Mine in Crystal Falls, both on the Menominee Range of Michigan. It is at these two mines that we have had our principal experience with belt conveyor installations underground, .At the Sherwood Mine, which has an annual capacity of about 450,000 tons, the first conveyor belt installationwas made in 1947 when conveyors were installed in the main haulage drifts on the 1200 ft, level, It was estimated at that time that approximately 5,000,000 tons would be mined from the stopes above the 1200 ft, level and. that if all this material could be moved to the shaft by belt conveyor, the entire cost of operation, including maintenance and the amortization of the equipment, would be about $,05 per ton, which was slightly more than half of what the cost would have been by conventional tramming methods employing locomotives and cars. Now, ten years later, the 1200 ft, level is almost completely mined out and we have actually removed. 5,200,000 tons and. the average cost of transporting this material to the shaft by belt conveyor has been $.095 per ton. Since there has been a substantial increase in hourly rate of pay and also in the cost of materials since 1947, we feel that the anticipated savings were very nearly realized., The 1200 ft, level installation at the Sherwood consisted of two 36" trunk line conveyors 815 feet long and 380 feet long, respectively, deliverying ore to the shaft. These in turn were fed. by three lateral 36" conveyors which paralleled the sides of the orebody, These gathering conveyors passed under draw points to which ore was brought from the stopes by mea S of scrapers or shaker conveyors, Shaker conveyors were used for a number of years in conjunction with the conveyor belt system of haulage but it was finally concluded that with this particular type of ore, the maintenance on shaker conveyors was excessive. Therefore, more recently, we have gone back to scrapers for the shorter distances and. are using belt conveyors in the scraper drifts for the longer distances. After this belt system had been in operation for about three years, it had proved to be so successful that it was decided to proceed with the same system or. a new level to be opened up 200 feet below. Instead of sinking the shaft and driving a horizontal drift to the orebody on the 1400 ft, level, an inclined conveyor drift was started near the shaft at the 1200 ft. level and driven downwards toward, the orebody at a slope of 15 degrees. The conveyor installed in this inclined drift is 36" wide, 990 feet long, is powered. by a 100 hp motor, and is capable of delivering 300 tons per hour to the 1200 ft, level shaft pocket. It is fed by lateral horizontal conveyors on the 1300 ft? 1400 ft., and 1425 ft, sub levels. Wien the inclined drift was started, the rock was scraped from the breast directly to the rock pocket at the shaft. As the distance increased., double scraping was employed, until the advance had reached 350 feet, At this point a portion of the final conveyor was installed, with a scraper slide near the breast, T e drift was then advanced be scraping on to the conveyor until a sufficient distance had been driven to permit the installation of an additional 200 feet of conveyor. This proved to be a very efficient and economical means of moving the development rock to the shaft and obviated the need of using cars or an inclined skip way, At the present time 85 percet of tie entire mine output is being mined below the 1200 ft, level and is delivered to the shaft via the inclined conveyor. The system appears to be working as well and as economically as did the conveyor systemonthe 1200 ft, level.

Jan 1, 1958

By Geoffrey Purcell

Improvements which have been made in commericial flotation systems during the past fifty years have resulted more from trial and error methods in the mill than from research in the laboratory. Research has often provided explanations of why mill changes have improved the metallurgical process. Hopefully, in the next fifty years, changes in mill flowsheets will come about, primarily, as a result of research work. However, since minerals, in their infinite variety, cannot be reduced to a standard state, research on commercial ores will have only a local utility, and research on pure minerals will have little commercial application. What will emerge from research on pure systems are mechanisms of adsorption, and this in turn may throw some light on the very much more complex adsorption processes taking place in the pulps of commercial ores. Quartz, without a doubt, has been the subject of more research effort than any other mineral, but we are still a long way from completely understanding its behavior in flo¬tation. Hematite and calcite have received considerably less attention. Ores containing a mixture of all three minerals, however, are commercially important, and the iron deposits in Alabama have been extensively studied by the United States Bureau of Mines (1). The literature reveals no reports of research on synthetic mixtures of all three.

Jan 1, 1967

By J. Frenzel

The computation of hydrometallurgical equilibria is very difficult because of the many complex species in solution, the precipitates, condensed species, or solids, and the activity coefficient corrections necessary to non-ideal thermodynamics. Our objective was to tryout recently developed genetic algorithms to minimize free energy and solve the equilibrium computation. We selected test problems that were seemingly unsolvable with more traditional algorithms, and we applied genetic algorithms to them. We were pleased to find that genetic algorithms succeeded where other algorithms did not. We concluded that they are an effective tool for hydrometallurgical equilibria.

Jan 1, 1992

By S. J. Jung

The prime criteria in the design of underground openings with complicated geological structures is ground control. Stability of underground openings for deep mines is critical because incorrect orientation or geometry of shaft, stope, and accessways often results in the failure of openings due to high stress conditions. Current design procedures for complicated orientation and geometry of mines are rapidly becoming inadequate as mines are being developed. In this study, finite element method has been used with optimization criteria to design more stable and safe underground openings.

Jan 1, 1993

By B. J. Scheiner

The Bureau of Mines, U.S. Department of the Interior, has investigated the use of rheology to provide insight into the mechanism of flocculation. A technique developed by Tattersall has been modified and used to explain the flocculation of calcium montmorillonite with polyethylene oxide. The results indicated that there are two types of bond systems operating during the flocculation sequence. Also, flocculation results are highly dependent on the shear rate and the amount of polymer added.

Jan 1, 1989

By James P. Dorian

istorical records suggest that the gathering of geologic information in China began more than 2,000 years ago. Modern-day geological work in the nation started in the early part of this century but it progressed rather slowly. Before the founding of the People's Republic of China (PRC), there were only 800 people engaged in geological work and only 200 trained geologists among them. According to Minerals and Mining in China, many accomplishments were achieved within China's mining industry during the period of years between 1949, the founding of modern China, and 1997. These include: ? The number of types of minerals with verified reserves increased from 18 (pre-Liberation) to 162 (today). ? Mineral deposit localities grew from 5,123 (pre-Liberation) to nearly 200,000 (today). Of these 200,000 localities, more than three-quarters have verified mineral reserves. ? Minerals extraction and processing contribute to 31 % of the total industrial output value of China (today). ? Regional geological maps at a scale of 1:1,000,000 covering the entire country have been completed, while regional geological and hydrogeological maps at a scale of 1:200,000 covering two-thirds of the country have also been finished (today). ? Before 1949, China was regarded as an oil-poor country. Since the 1950s, China has developed an extensive petrochemical industry. It is largely government-owned except for a limited number of joint ventures. The central government maintains active control over China's most productive fields, including the Daqing field in the Songliao Basin of northeastern China and the Shengli and Liaohe fields in the Bohai Basin of northeastern China. ? Employment in the minerals industry engaged in geological exploration increased from 800 (pre-Liberation) to 1 million (early this decade). The new report provides an overview of the current political and economic situation in China and discusses how this affects the minerals industry. China is in transition between a socialist planned economy and a market economy. This makes it difficult for non-Chinese to keep track of developments. Minerals and Mining in China is divided into 14 chapters that contain detailed statistics, including data on the geographical location and extent of known mineral reserves, production rates, local technical personnel, imports and exports. The report reveals which companies are already active in the area by profiling 50 major investment projects in China's metals and minerals industry. According to its author, China possesses one of the world's largest mining industries, ranking among the leading producers of several metallic and nonmetallic resources. The Chinese mining industry is extraordinarily complex. It has evolved into an overwhelmingly large bureaucracy that was, until the 1980s, shrouded from and misunderstood by the international community. To date, more than 160 types of minerals have been discovered in China. But a significant portion of the minerals and energy base remains largely unidentified and evaluated. And despite China's large reserves of mineral resources, with a population of more than 1.2 billion people, the country ranks among the lowest in the world in terms of proven reserves per capita. In addition, mining recovery rates in China average about 50%, significantly

Jan 1, 1999

By Margaret Armstrong, Arne Berckmans

The longterm aim of this research project is to find fast ways of simulating the recoverable reserves of a deposit for input into financial Monte Carlo simulations without having to conditionally simulate the whole orebody many times. The first step in this re- search is to visualize and quantify the ore tonnage T and the metal quantity Q above an arbitrary cutoff z. This paper presents detailed results for one specific distribution, the lognormal. These lead to a suggestion of a fast way of simulating QTz curves.

Jan 1, 1996

By J. D. Patsey, G. T. Lineberry

A.E. Hall The authors are to be commended for their attempt to provide a convenient piece of software for preliminary drum hoist specification. This field has received little attention in recent years and is eminently suited to calculation by computer. Unfortunately, there appears to be an error in the calculation of the required rope diameter. The 66-mm (2 5/8-in.) rope selected is oversized for this application. Wire rope weight and breaking strength are related to the rope diameter. For a round strand rope

Jan 8, 1987

By E. H. Partelpoeg, B. G. Belew

In 1990, the Chino Smelter completed the construction of a plant designed to recover metal values and water from smelter scrubber effluent. Equipment was installed to maximize effluent recycling and minimize costs. The process utilizes magnesium hydroxide as a neutralizing agent which has the advantage of precipitating copper from solution with minimum generation of solid reaction products. The neutralized stream is clarified, with solids recycled to the smelter for metal recovery while the clarified effluent is recycled to the concentrator for use as process water.

Jan 1, 1992

By A. E. Hall

The authors are to be commended for their attempt to provide a convenient piece of software for preliminary drum hoist specification. This field has received little attention in recent years and is eminently suited to calculation by computer. Unfortunately, there appears to be an error in the calculation of the required rope diameter. The 66-mm (2 5/8-in.) rope selected is oversized for this application. Wire rope weight and breaking strength are related to the rope diameter. For a round strand rope

Jan 1, 1988

By Paul L. Russell

U. S. petroleum demand has increased at a rate greater than that of domestic production. A domestic energy source that is under serious consideration to augment present supply is oil shale. The Green River formation in Colorado, Utah, and Wyoming represents a resource potential containing about 2 trillion bbls. of oil in shales averaging 15 gallons or more per ton or more than 400 billion bbls. in 30 gallon per ton shales. This paper will consider the technological and environmental aspects of developing this resource.

Jan 1, 1974

By Y. Ye

Induction times for a variety of minerals have been measured at a particle bed. Electrostatic repulsive forces between bubble and particle generally are of secondary importance in determining the hydrophobic state; nevertheless, the shortest induction times are measured at the isoelectric point of the solid. More importantly, the study shows that the film-rupture mechanism at a polished surface might be different from that at a particle bed. The induction time measured at a particle bed, besides being dependent on the surface chemistry of the system, shows a definite relationship to particle size and density. Theoretical analysis suggests that such a measured induction time at a particle bed should properly be defined as an attachment time which consists of the induction time and the film-displacement time. Thus one portion of the measured attachment time is the induction time, the time required to thin the water film between the particle surface and the gas bubble to a critical thickness so that rupture of the film takes place ('1)' The other portion of the measured attachment time is the time required for the film to be displaced to such an extent that the attachment is stabilized with respect to the upward motion of the bubble and the downward gravitational force acting on the particle ('2)' Further, the present study illustrates that '2 is related to the hydrophobic character of the surface, the rate of film displacement after rupture, the upward velocity of the captive bubble, and, most importantly, the particle size and density.

Jan 1, 1988

By Robert J. Whiteley, Colin Parker

Two major tunnel projects with a combined value of about $US700 million have been recently completed in Sydney using both soft ground and hard rock Tunnel Boring Machines. The first of these and the main entry in Australia for the Year 2000 Olympics was the New Southern Railway. This is 10 km of mainly soft ground tunnel linking the Sydney’s International Airport with the Central Business District. The second tunnel was designed to alleviate major stormwater pollution of Sydney Harbour and involved construction of the Northside Storage Tunnel. This is19 km of hard rock tunnel at depths exceeding 90 m that connects many of the northern Sydney suburbs of Sydney with the North Head Ocean Outfall. Case studies of these projects describe the use of innovative geophysical technologies comprising gravity and seismic tomographic imaging with geotechnical testing at the feasibility and design stages. This approach minimised construction and financial risk by effectively quantifying the significant geological and hydrogeological issues along these tunnel routes that exerted major controls on these projects.

Jan 1, 2001

By Pierre Ollivier, Dominique Morin

A general study of gold refractory arsenopyrite pyrite concentrate bioleaching has been carried out including two continuous bioleach testworks at different sizes, namely one at a laboratory scale with a 100 1 unit at a 2 kg/d dry solid flowrate and the other at a pilot scale at a 100 kg/d dry solid flowrate. Both tests show a 80% bioleaching of arsenopyrite in about four days of treatment and with the same kinetic. Pyrrhotite is attacked at the earlier stage of the bioleaching but pyrite remains unaffected. The weak potential of oxidation associated with the decomposition of arsenopyrite and the abundance of arsenite leads to a high grade of elemental sulfur in the bioresidue which consumes the major part of the cyanide during the gold recovery, furthermore, the arsenite and ferrous produced in solution have to he oxidized to obtain a stable precipitate in the waste products and as outlined in previous works of other authors on this subject the addition of iron to obtain a Fe/As molar ratio at least above 3 is necessary. The agitation equipment used in the pilot unit allowed an optimisation study calculation for scaling-up the design and power requirements of an industrial installation, For the pretreatment of a gold refractory As high-graded concentrate the reagent cost has the greatest part in the operating cost of the biooxidation step due to the necessary retreatment of the biosolution, In that conditions the power cost is quite marginal, actually it is significant for the treatment of pure pyrite.

Jan 1, 1990