Search Documents

By Roshan B. Bhappu

In situ mining and extraction is one of the Frontier Technologies that is destined to play an increasingly important role in the recovery of metals and minerals in the future. This premise is based on increasing costs of labor and energy, increasing awareness of environmental considerations and decreasing ore grades in the United States. Up to now, in situ mining has been successfully applied to a few favorable situations for the extraction of some evaporites, copper and uranium. However, because of its unique technical, environmental and economic advantages, this versa tile technology will find broader applications for the recovery of above commodities as well as for others which are currently extracted by hydrometallurgical means. This paper traces the development of in situ mining and extraction; stresses its dependence on interdisciplinary science and engineering; discusses its theoretical, practical and economic aspects; and finally presents potential applications of this Frontier Technology.

Jan 1, 1985

By Everett H. Dobbs

The Tripoli deposits in the southwest corner of Missouri In Newton County and the northeast corner of Oklahoma in Ottawa County, located in the vicinity of Seneca, Missouri, contains an unusual and peculiar form of silica which has not been found any other place in the world. Its outstanding characteristic is the physical structure of the individual particle, The particle structure of the Missouri-Oklahoma type Tripoli accounts for its market. It is a soft, friable, porous, double-refracting silica of the chalcedony variety, The particle is porous, has a fibrous structure, no sharp edges or comers, ad an average size of less than .01 millimeter, It varies from 90 to 98 per cent Si02 with less than 1 per cent free silica in the form of quartz, 24; has ignition loss of 1 per cent and fractional percentages of iron, alumina, lime, etc.

Jan 1, 1960

By J. A. Herbst

Introduction The ability to evaluate the improvement resulting from the implementation of an automatic control system is essential to the Justification of its cost. This evaluation may occur after anew control system has been commissioned. In other cases an existing plant which is operated manually may be automated only In part in order to determine In ether the met of it should be. Finally. in some instances dynamic isolation my be used prior to installation of the control system to determine the strategy to be used or to evaluate the improvements In process performance expected from automatic control. This paper describes the development of a methodology for making these evaluations. In order to obtain an accurate assessment of Improvements In a short time, statistical methods can be employed. Mineral processing plant, are subjected to many types of both random and deterministic disturbances of various duration. The statistical method, available for process control at analysis are designed to counter the obscuring effects that random disturbances have on such as evaluation. The basis for evaluation and comparison is some freely chosen measures of process performance termed the performance index or objective function. The experimental data used to calculate the performance index should, if possible, be collected by alternately running a circuit Or plant with the two or more type, or control being tested ("serial testing”) or more preferably, by running two circuits with the two type, of control side by side ("parallel testing") . The performance index is a random variable so that when comparing two types of control, statistical hypothesis testing must be used. By testing s hypothesis statistically one accept, or reject, a (null) hypothesis [ ] concerning the mean or variance of one or more performance indices. For example, a hypothesis Ho might be that the mean of a performance index with stabilizing control is larger than with manual control. Defining a Performance Index The performance index, denoted by [ ] , is a measure by which alternative strategies or situations my be cam peered on either s technical or an economic basis (see Table 1). Technical measures are concerned with the effects of control on process variables or outputs or on the deviations of controlled variable, from their setpoints. For commotion circuit, important technical measures of performance are throughput, product fineness and the consumption of liners, media and electrical energy. For flotation circuits important technical .satires are recovery, grade and reagent consumption. Economic measure such a, cost and profit n usually determined from a combination of technical measures and are usually the final factor upon which a decision may be made, although a control system my achieve higher values of technical measure , the control effort expended my be of such magnitude that the economic measures, such as cost, are poor. Running Comparisons Comparison, between automatic and manual control are normally done with data obtained before and after control system Installation, unless ore characteristics remain the same during the period of data collection the results will be biased. By running the test circuit with the control system alternately turned on and curled off until all possible ore type, have been run through the circuit, unbiased result, can be obtained. This mode of testing is termed “serial testing.” An alternative and potentially more powerful and quicker made of testing is "parallel testing" in which two circuits, one with the type of control being tested and one without, arm run aide by side. In this type of testing both circuits process the same ore so that valid results occur sooner than with aerial testing. The data may be averaged before testing or the differences in the performance indices may first be calculated before averaging. However, the two circuits must be nearly identical in their mechanical characteristics otherwise differences other than the degree of control will bias the results. It mechanical differences exist than it my be necessary to adjust one or the circuits prior to testing. Sometimes it is possible to correct far mechanical differences based on Inherent efficiency calculations made with a model. Hypothesis Testing Once the data is collected, hypothesis fencing can be carried out to determine if the automatic control system has resulted in a statistically significant improvement. One can construct a histogram of the distribution or performance indices with am without control such as Figure 1, or the

Jan 1, 1991

By D. Hodouin

The optimisation of mineral processing plants requires the evaluation of performance indices such as production rate, product quality, valuable mineral recovery and process efficiency. Decision to change operating conditions or equipment to improve plant performances rely on the significancy of the estimated performance indices. The better is the quality of the estimation, the better is the discrimination capability of the index and as a consequence the larger is the operation improvement. The reliability of performance calculation depends on the sensors nature, accuracy and location, on the data redundancy, on the correction method applied to raw data and finally on the propagation of measurement errors along the calculation of performance indices. To maximize the quality of the data collected for performance evaluation, the following techniques are presented, discussed and illustrated: redundancy and observability analysis, data filtering for mass conservation, variance analysis of performance calculation, and data acquisition strategy design.

Jan 1, 1991

By Ramesh Malhotra

Overseas coal trade has increased from 169 to 274 million metric tons (tonnes) between 1970 and 1983, representing a 3.8% average annual rate of growth. Metallurgical coal accounts for nearly 61% of the international coal market while steam coal's share is about 40%. By year-end 1983, the U.S. was the single largest coal exporter at 77 million tonnes, followed by Australia, 56 million tonnes; Poland, 35 million tonnes; South Africa, 28 million tonnes; USSR, 27 million tonnes; and Canada, 17 million tonnes. Coal exports can play a more significant role for one country than another country. For instance, in the U.S., coal exports accounted for only 9% of total coal demand in 1984 while in Australia, exports accounted for 53% of that country's total coal demand. Of all the major coal exporters, only U.S. exports accounted for less than 10% of total consumption in 1984. Japan is the largest importer of coal, 73.8 million tons in 1983. Although the majority of Japan's imports are metallurgical coal, steam coal imports into Japan increased seven-fold between 1978 and 1983, from 2 to 14 million tonnes. Australia is the leading exporter of both metallurgical and steam coal to Japan, accounting for 47% and 55% of Japan's coal imports, respectively. Since 1978, South Africa has developed into a major steam coal exporter to Japan, increasing its market share from 7.9% to 18.8%. The U.S., which was not even a player in Japan's steam coal market in 1978, has made inroads and accounts for 6.7% of Japan's steam coal imports. However, this translates into only one million tonnes. In the European coal market, for the most part, the U.S. is the leading supplier of metallurgical coal and South Africa is the major supplier of steam coal. The U.S. was not even a factor in the European steam coal market in 1978 and has made inroads during the last six years at the expense of Poland and South Africa. From 1978 to 1983, the U.S. has increased its market share in steam coal exports to France from 0.2 to 28%; Spain, 0 to 52%; Italy, 0 to 43.5%; Denmark, 0 to 19%; Germany, 0.5 to 16%; and the Netherlands, 0.6 to 45%, respectively. The use of coal (solid fuels) as a fuel to produce electricity has had increasing signficance for most of the countries analyzed between 1978 and 1983. The flip side to this is that oil has lost its share of this market during this time period. Of all the countries selected, only France reported a decline in coal's share of total electricity production. This is a reflection of France's ambitious nuclear program.

Jan 1, 1986

By P. Venkatraman, F. S. Knoll, W. S. Kow

Froth flotation is the most widely used technique for cleaning fine coal. This practice may change, however, with the development of enhanced gravity concentrators such as the Mozley Multi- Gravity Separator (MGS). The MGS is a flowing-film concentrator that utilizes centrifugal forces to improve the separation of flotation-size particles. In the present work, a pilot-scale test program was conducted to examine the effects of feed rate, feed solids content, wash water flow rate and drum rotation speed on the performance of the MGS. The test results indicate that the MGS effectively rejects high-density minerals such as pyrite, while ultrafine ash-forming minerals are removed less efficiently. A major advantage of the MGS is that high separation efficiencies can be realized without additional grinding, flotation reagents or heavy media. This article describes the working principles of the MGS and presents data obtained from recent pilot-scale test work.

Jan 1, 1995

By L. E. Krys, K. D. Harrison, S. M. Nordwick, C. G. Anderson

Since 1984, nitrogen-species catalyzed pressure leaching has been utilized at the Sunshine Mining and Refining Company for the recovery of precious metals from a refractory sulfide concentrate, The process operates without the use of cyanide. The plant is now the only industrial-scale commercial application of this technology. Since the inception of the process, changes have been implemented to improve efficiencies and throughputs. Two of these changes, the replacement of nitric acid by sodium nitrite and a concentrate regrind, have recently been implemented. This paper will discuss the outcomes of these recently patented plant-process changes. In particular, a comparison between the previously used method and the new leach method is made. Also discussed is the potential applicability of the process to other materials. A companion publication (Anderson, Harrison and Keys, 1996) indicates possible mechanisms responsible for the success of these process changes.

Jan 1, 1997

By R. J. Sweigard, G. T. Lineberry, B. K. Slone, F. A. James III, D. S. Maggard

The depth at which it becomes more economical to use slope access instead of box-cut access for nearsurface coal reserves is termed the "transition depth." The transition depth can be established for a given coal property by considering cost estimates for those parameters that determine respective access methods. Fourteen parameters that influence access cost were identified, and ranges for these parameters were determined. A transitiondepth formula was developed to permit the determination of which is the better method of accessing a reserve, given information such as high wall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs and the cost of overburden removal and reclamation. In most cases in Appalachia, especially in eastern Kentucky, the observed transition depth ranges from 20 to 30 m (66 to l00 ft). This indicates that actual practice is consistent with the analytical approach used.

Jan 1, 2002

By R. Larry Davis

Over the past decade there has been a continual decrease in domestic oil reserves accompanied by a sharp increase in the demand for energy. Even with increased imports of foreign oil, the energy demand has not been met. This has forced many users to turn to substitute fuels. Of the many substitute fuels available most users are turning to and creating an increased demand for low sulfur coal. Because of the increased demand for low sulfur coal as well as the inherent problems in producing eastern coal, many producers have turned their attention to the large deposits of low sulfur coal in the western United States. Western coal mining is, however, not without its problems such as high moisture content, high ash content, highly variable sulfur content, multiple seams, and/or pitching seams. It is to aid in the solution of these problems that this chapter is directed.

Jan 1, 1979

By J. A. Herbst, Z. Rogovin, Lo. Y. C., K. Rajamani

Knowledge of the amount of time material spends in a continuous mill in a closed grinding circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of pulse tracers in residence time distribution (RTD) experiments. In typical grinding circuit experiments, RTD measurements are done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article, an easy mathematical method for calculating mean residence time and the degree of mixing of material in a mill present in a closed grinding circuit is developed. There are no restrictions on the location of the tracer injection or detection points with this method. Any convenient location in the circuit can be chosen without affecting the residence time distribution measured. The analysis of impulse response data obtained from several commercial grinding circuits using this method is presented.

Jan 1, 1988

By Lawrence Adler

[An innovative framework is proposed which most efficiently and systematically handles the large quantity of information needed for equipment failure and other non-performance analyses. It is based on the accepted engineering dimensions of mass (material), length (geometry), and time (MLT). To these are added human and machine factor. Several failure "Modes" are identified for each dimension, which are then subdivided into specific "Types". Material Failure Modes such as Separation and Slip are easily recognized, but others had to be established. Geometric Failure Modes are usually straight-forward, Obvious ones include Geometrics Design and Stability with more synthesized. Time Failure Modes are again largely self-evident such as Life and Chemical Effects, others are needed. Human and Machine Factors as failure modes are loosely assembled. The results contain strengths, but also organizational weaknesses which are noted. Lacking a better alternative its use is recommended.]

Jan 1, 1989

By John A. Organiscak

The Bureau of Mines evaluated a new dust control technique for longwall personnel required to work at the tailgate end of the face. This technique utilizes a water-powered scrubber to clean a portion of the face air, which is discharged behind a brattice partition at the working area. Laboratory simulation of this system in a wind tunnel resulted in average efficiencies greater than 70 pct with system efficiency directly related to scrubber quantity. Underground evaluations indicated a similar direct relationship between scrubber quantity and system efficiency. Gravimetric measurements of respirable dust made during these underground evaluations resulted in average protection efficiencies ranging from 30.7 to 42.5 pct with increasing scrubber air quantity.

Jan 1, 1983

By R. Cook

Knowledge based applications are becoming important to Associated Manganese for efficiently dispatching ore of appropriate grades to customers on time. The G2 expert system shell has been used to develop blending and scheduling applications using a combination of object-oriented rule based, procedural, and heuristic approaches. The blending application, for example uses a heuristic approach for creating blends from thousands of small stacks of manganese ore of various grades and sizes, to meet customer specifications while fully exploiting the available inventory. Data capture and data warehousing have become important issues, and the Internet shows strong potential for distribution of pre-processed information.

Jan 1, 1997

By R. Balderrama Neder

A study consist in 20 column leach tests was performed for the "EI Arco" Copper ore deposit, located on Baja California, Mexico. The main purpose was to define the basic criteria like recovery and sulfuric acid consumption, for a commercial heap leach system design, to process the oxide Copper (Chrysocola) of the deposit. Leach parameters such as, amount of sulfuric acid in the cure solution, cure technique, particle size of the material, leach solution's flowrate application, leach solution's acid strength and height of the lifts, were evaluated to choose those parameters in which the results were the best ones for that particular design.

Jan 1, 1997

By Graeme J. Jameson

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about one metre (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash-water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1988

A form of column flotation cell is described in which the contact between the feed and the air stream is made in a mixing device at the top of a vertical downcomer. The air-liquid mixture flows downward to discharge into a shallow pool of pulp in the bottom of a short cylindrical column. The bubbles disengage and rise to the top of the column to overflow into a concentrate launder, while the tails are discharged from the bottom of the vessel. The main advantages of the device described are that the overall height of the column is reduced to about 1 m (3 ft), and the column can be self-inducing with respect to the air supply. Experimental results are given from tests on a feed stream to a conventional zinc cleaner circuit. Using wash water to reduce gangue entrainment, the column gave high concentrate grades and high recoveries.

Jan 1, 1987

By Catherine T. Aimone

A computerized cost model has been developed to simulate the technical and economic effects of strip mine blasting in the vicinity of structures. Current surface mining regulations restrict the allowable level of production blasting as a function of this distance. Blast design modifications,' therefore must be employed when blasting in the vicinity of homes to ensure compliance with federal and state regulations specifying limits to the seismic effects generated from a blast. The blasting level allowed. is computed by the charge weight of explosives per delay from the following scaled distance formula: [ ] where W is the charge weight per delay, in kilograms (pounds), D is the distance factor corresponding to the regulatory limit of peak particle velocity to which a structure may be subjected to. Current regulations specify 2.54 cm (1.0 in.) per second corresponding to a SD factor of 27 (60) (Federal Register, 1977).

Jan 1, 1982

By Peter T. Luckie, Mark S. Klima

INTRODUCTION A physical separation partitions a stream of particles into two streams - one containing a concentration of a desirable constituent; the other containing a defficiency - on the basis of a difference in physical properties. Separating ores into concentrates of increased grade and gangue minerals has been practiced for thousands of years. Physical properties of materials which have been used to achieve separations include size, relative density, shape, magnetism, surface charge, color, characteristic emission, resilience and strength. The study of physical separations has also been termed attribute tracking. The term attribute is used to describe the content of the material of interest, or, sometimes, properties not used as a basis of the separation. The content is usually given by its assay; e.g., %Cu, %Fe, etc. Attribute tracking involves material balancing. For a separation using two physical properties, say x and y, the balance is

Jan 1, 1986

By Rodger E. Denison

The Middle Ordovician Simpson Group in the Arbuckle Mountains of southern Oklahoma contains sandstones of unusual purity. These have been exploited as glass sands since 1913 (Ham, 1945). Where quarried, the sandstones are uncemented or weakly cemented, greatly facilitating mining and processing. The origin: sedimentary setting, and lack of cementation of these valuable sands has been the source of much discussion. The lowest of the sandstone units in the Simpson is at the base of the Oil Creek Formation. The basal Oil Creek sandstone is exposed in a series of accessible quarries north of the town of Mill Creek in Johnston County. Virtually all conclusions and generalizations concerning origin of the Simpson sandstones are based upon observations made in these quarries. The three Simpson sandstones overlying the Oil Creek share many of the same distinctive qualities, and there is an assumption that they share a common origin.

Jan 1, 1999

By Jon G. Baird

The suggestion of the use of measurements of trace amounts of mercury as a guide to the location of sulphide ore deposits was first made by the Russian, A. A. Saukov (1), in 1.946. Since Saukov's original work, many others have studied the abundance of mercury in nature, the association of mercury with sulphide ores and methods by which very minute quantities of mercury can be measured in air, soil, rocks, water and plants. The most abundant of the mercury bearing minerals is cinnabar (HgS). Native mercury is also found and sulpha-salts like tetrahedrite are known to have important mercury contents. Other sulphides of base metal deposits contain mercury in amounts ranging from parts per million to as much as one or two percent. (2) The mercury content of sulphide-free rocks is usually less than a few hundred parts per billion (1 ppb - 10-9), Soils usually contain less than 100 ppb and water less than 1 ppb of mercury. Normal atmospheric air contains about 1 nanogram (10-9 grams) of Hg per cubic metre although higher concentrations can be observed near mercury occurrences, sulphide deposits and volcanic exhalations.

Jan 1, 1973