Search Documents

By A. K. Sinha

Despite the tremendous efforts and costs incurred by the industry and regulatory agencies to prevent premature roof failures in underground mines, roof falls continue to occur frequently due to the very unpredictable geological conditions and dynamic nature of mining operations. In fact, roof falls continue to be the largest contributor to coal mine fatalities. The failure of a mine roof generally occurs following a prolonged, gradual degradation in its physical conditions. An electronic mine roof monitoring system has been developed and tested in operating mining sections. It monitors mine roof degradation on a continuous basis. The field test results are presented and discussed.

Jan 1, 1987

By A. K. Sinha

Research shows that continuous mining sections can normally produce around 950 tons per shift in a seam 5 or 6 ft. thick. The shuttle cars as well as the continuous haulage systems are able to match with the continuous miners in capacity. However, in practice both of the two systems seem to be averaging at around 450 to 500 tons per shift in production. Continuous haulage systems are preferred in thin seams particularly where the floor is soft.

Jan 1, 1981

By Steve Hicks, Zach Agioutantis, Greg Hasenfus, Zach Wedding

Most prediction methods used to calculate mining-induced subsidence rely on empirical formulations, which typically assume flat topography and uniform properties in the overburden. It is also well known that when a longwall panel mines below a valley bottom surface ground deformation magnitudes and orientations may be significantly influenced by the presence of the valley. This paper discusses ground deformation data collected at different surface locations above the Buchanan mine in the eastern United States. Measurements at individual surface points and strata movement measurements using a three-point extensometer have been collected as the area was undermined. Measurements correspond to the mining of the panel immediately under the measurement points and to the mining of adjacent panels. Measurement locations correspond to valley bottom locations. The measurements are critically evaluated and compared with respect to topography and panel face location. The issue of the fluctuation of GPS measurements is also discussed.

Jun 25, 2024

During foundry sand reclamation process development, molds formed from reclaimed chromite sand showed a rapid decline in tensile strength during thermal cycling tests. Because this characteristic could limit reuse of chromite sand in the foundry, the sand was examined in detail. Scanning electron microscopy, x-ray mapping, magnetic susceptibility, and x-ray diffraction were utilized to evaluate processed chromite sand. It was found that process variables such as binder composition, reclamation temperature, and processing method had a significant effect on the chromite sand particle surface. X-ray diffraction indicated a crystallographic change in the processed sands. Magnetic susceptibility also increased after processing. Diffusion of iron to the particle surface and increased surface roughness were identified as potential causes of the decreased tensile strength in the molds.

Jan 1, 1993

By Robert C. Salak

The era of low-seam mining with continuous haulage has been here for quite some time. Typical tonnages in companies such as Terry Glenn Coal are currently averaging 405 tonnes per shift in .8m coal. JoAnn Coal has averaged 453.6 tonnes per shift in .775m to .825m coal for the past four years. John Chaney of Chaney Coal has averaged 297 tonnes per shift in .6m to .65m coal. There are many other mines that are experiencing similar success and with maintenance costs that are averaging $.10 to $.40 per tonne. These figures have been documented and can be verified by the operators.

Jan 1, 1981

By W. E. Benton

Diatomite or diatomaceous earth is a siliceous sedimentary rock principally made up of the skeletal remains of the diatom, a microscopic, single-cell aquatic plant related to algae. The unique structure, chemical stability and physical properties are the major attributes of diatomite not met by other forms of silica. The production of diatomite was down in 1982 vs. 1981, reflecting the worldwide recession. The principal markets for diatomite products continue to be basically filtration and fillers. The outlook is for small but steady growth into the 1990s.

Jan 1, 1983

By F. Segobia, M. Portal, F. Ysla, L. Goicochea

It is our responsibility to promote responsible and sustainable mining with new generations, promoting a culture of equality and respect. To fulfill this commitment, we are working with the SME UNC Student Chapter team, Newmont Yanacocha, BRG Women and Allies and the Museo de Agua y Tierra (MAT) to carry out the “Building our future” project. It is our responsibility to promote responsible and sustainable mining with new generations, promoting a culture of equality and respect. To fulfill this commitment, we are working with the UNC SME Student Chapter team, Newmont Yanacocha, BRG Women and Allies and the Museo de Agua y Tierra (MAT) to carry out the “Building our future” project. This project seeks to instill in new generations the importance of mining, integrating sustainable development objectives. We have the participation of Newmont Yanacocha and external professionals, who share their life stories and inspire participants from rural and urban educational institutions to pursue their dreams and aspirations. We believe that this project is important because it will help new generations understand the importance of mining and its role in the development of the country, covering the economic, environmental and social spheres. Since its inception in 2022, the project has positively impacted more than 500 participants.

Feb 1, 2024

By D. A. Stanley

Researchers at BCD Technologies and the University of Alabama have applied three statistical techniques to the information contained in a large database of measurements from a phosphate ore processing plant. The rust, Principal Components Analysis (PCA), replaces many measured variables with a few fundamental and un-correlated variables. The second technique, Projection to Latent Structures (PLS), is an extension of PCA that explores the relation between variables identified as either independent or dependent. The third technique, Cluster Analysis (CA), is applied to the results of the PCA or the PLS calculations, and identifies individual data clusters that represent uniform operating conditions in the plant. All three statistical methods can be seen as geometrical operations on the data viewed as points in space. A Viewer gives a corresponding graphical presentation of the data points. This paper describes the use of the above three techniques and the Viewer to explore part of the phosphate flotation database.

Jan 1, 1998

By D. C. Hatch

At the MacIntyre Development of the Titanium Division of National Lead Company a magnetite-ilmenite ore together with gabbro-anorthosite waste is mined from an open pit by shovels and trucks. The ore from the pits is trucked to ore stockpiles for blending ahead of the crusher and to free the mine from crusher delivery schedules. The ore stockpiles are blended to yield a 16.5 to 17.0 % TiO, crusher feed. This requires mining on an assay cut-off rather than a visual grade cut-off. Highly mineralized ore runs from 20 plus % TiO2 and 30 plus % Fe to 15 % TiO2 and 40 plus % Fe as the ratio of ilmenite to magnetite changes. There are three major ore types in the present pit with magnetite ratios varying from about one to one up to three times as much magnetite as ilmenite. Ilmenite and magnetite together liberate from gangue down to about 10 mesh and this is the basis of the magnetic cobbing. Below 10 mesh the ilmenite and magnetite start to separate and ore cobbing pulleys will not hold the ilmenite.

Jan 1, 1968

By A. T. Yu

As a nation, we have been known as perhaps the most wasteful in history. From the perspective of engineers and builders on the other hand, planned obsolescence and demolition did beneficially pave way for growth and provided environment for new businesses. Recent economic recession and intense competition from overseas, however, have drastically changed the economics. The high cost of capital and the demise of indiscriminate plant expansion have totally altered the way we conduct our business and run our operations. As a response to increasing demands for better efficiency with little or no funding available, everyone is forced to make do and do better with whatever little he has. Today it nay not be an exaggeration to state that modification of existing facilities may have finally emerged as a way of life. This paper will outline examples of how several companies have effectively modified existing facilities to do more and do it efficiently without having to demolish everything and/or to spend a fortune.

Jan 1, 1985

By Wenbing Guo, Gaobo Zhao, Erhu Bai, Brijes Mishra

"Violent damage to overlying strata can occur above the large mined-out space left by high-intensity longwall mining. For the safe mining under the aquifer and surface water body, it is imperative to investigate the criteria of overburden failure degree due to high-intensity mining. In this paper we present the characteristics of high-intensity longwall mining panels and overburden critical failure. Based on the geological and mining conditions of a high-intensity mining panel, 3D numerical models that consider the maximum horizontal principal stress and minimum horizontal stress and their orientations with the panel advance direction were established by using the 3DEC software. Sizes of the panel reaching the critical failure of the overburden under different mining thicknesses (3.5 m, 6.5 m, 9.5 m, 12.5 m, and 15.5 m) were analyzed. Further, criteria of overburden critical failure were proposed for the high-intensity mining. The coefficient of overburden critical failure (Cf) is the ratio of the strike length (Ls) to the mining depth (H). Through curve fitting analysis, a fitting equation between Cf and mining thickness was obtained. The results showed that overburden failure criterion with high-intensity mining panel is 0.38 = Cf = 0.97 with different thicknesses. Field measurements validated the results from the numerical models.INTRODUCTIONHigh-intensity longwall mining refers to a coal mining method with thick coal seam, large panel width, fast face advance rate, and severe damage to the overburden and surface in China (Guo et al., 2018). Violent movement of the roof rock and severe damage to overlying rock strata occur in the large mined-out space left by a high-intensity longwall mining panel, which is a 3D (three-dimensional) structure layout with highly non-uniform stress distribution. Recognition of such fact a will facilitate this overlying rock strata failure problem investigation (Peng et al., 2019).The studies of overlying strata failure due to longwall coal mining have been reported by some scholars with different methods. Kang et al. (2018) studied the sudden massive roof collapse during longwall coal retreat mining by a large-scale two-dimensional physical model and a UDEC numerical model. Ghabraie et al. (2015) researched the mining-related strata movement by applying the three-dimensional laser scanner, optical transducer, and digital image processing techniques to two-dimensional physical models. Wang et al. (2015) analyzed the structural characteristics and fracture failure process of overlying hard and thick main roof by a 3DEC numerical model; this study also investigated the geostress reduction and permeability enhancement redistribution of the adjacent coal measure strata by FLAC3D. Guo et al. (2012) performed a three-dimensional finite element analysis and shared some insights into the dynamic interaction between mining induced strata stress changes, failures, and gas flow patterns. Meng, Shi, and Li (2016) proposed a 3D coupling model between stress and permeability, investigating the dynamics of a stress, permeability coefficient using FLAC3D. Khanal, Guo, and Adhikary (2019) used the 3D numerical modelling approach (COSFOW) to investigate the strata deformation and the change in permeability in the overburden strata due to the underground extraction. However, few studies considered the influence of the horizontal stress on overburden failure in a high-intensity longwall mining panel, and the critical failure criteria of overlying rock strata is unclear."

Jan 1, 2019

By R. R. Givler

Since the 1860's the good ole days, oil has been nozzle fed to burners under pressure atomizing the oil into droplets -- 1960's has produced vaporized oil that burns oil with the flame color and consistancy of gas -- If you can tell the difference by looking at the flame, gas or oil I?ll buy the lunch. First, we must ask, "Why all the excitement about Blue Flame?" This question is best answered by you after you have studied the principle of operation and see the result. I will attempt to explain both of these so that you can draw your own conclusions.

Jan 1, 1975

By L. Mao

A first-order flotation rate equation was derived by incorporating both hydrodynamic and surface forces involved in bubble-particle interactions. The hydrodynamic forces were calculated using an appropriate stream function, while the surface forces calculated using the extended DL VO theory. The equation was used to predict flotation results as functions of several important parameters such as contact angle, Zeta potentials of air bubbles and particles, and bubble size. The predictions are consistent with experience, and can be explained in view of the various sub-processes considered in the model.

Jan 1, 1997

By C. E. Jordan

The fundamental characteristics of ultrafine chalcopyrite flotation were investigated by the Bureau of Mines to establish techniques to improve recovery of ultrafine chalcopyrite. Intense agitation during conditioning was found to improve flotation recovery of the ultrafine chalcopyrite. A split-circuit flotation design, treating the plus 38-µm-size ore by the conventional method and treating the minus 38-µm-size ore with intense agitation conditioning followed by flotation, recovered 95.6 pct of the copper in a 28.3-pct-copper concentrate, This was a 5-pct increase in copper recovery over the conventional chalcopyrite flotation method.

Jan 1, 1986

By William Laird

In the process of mining coal today, our greatest asset, the coal miner, is faced with the indirect and direct consequence of underground mining operations. The indirect considerations may be the rank of the coal seam, the amount of overburden, geological factors, seam permeability and cracks. The introduction of newer, bigger and faster coal-producing face equipment having the capability to cut or rip through the bedding planes, cleats and micropores of the coal seam brings about rapid liberation of gas accompanied by greater concentrations of coal dust, has exerted a direct consideration and greater demand upon mine ventilation systems and dust control. The purpose of mine ventilation is to provide sufficient pure air to the miners working underground and to dilute, render harmless, and carry away all the dangerous and noxious gases. The mining operations which create coal dust are cod cutting, drilling, blasting, loading, hauling, dumping and movement of face equipment. The created fine dust causes the propagation of explosions. When quantities of coal dust with no methane present are raked in a sufficiently dense cloud in the presence of a source of ignition, an explosion is possible.

Jan 1, 1980

By P. Somasundaran, D. R. Nagaraj, Tarun Bhambani, P. Patra

Flotation separation and recovery of value minerals from ores containing fibrous silicate minerals are known to be quite challenging. Earlier studies have established that the metallurgical challenges (poor selectivity and recovery, high energy consumption, etc.) arise from the impact of the fibrous minerals (with high aspect ratio) on pulp rheology, which was found be rather complex. The complex rheological behavior of ore suspensions containing particles with high aspect ratio and its influence on flotation outcome are investigated in this study. Flotation tests and rheological measurements were carried out with both ores (containing fibrous minerals) and a model system comprising nylon fibers (chemically inert) added to a copper ore that had no fibrous mineral. These studies allowed the determination of contributions of physical properties of the fiber to pulp rheological behavior. Optical microscopy images of the fiber pulp indicated that the fibers entangled to form two levels of microstructures: two-dimensional (2D) aggregates under semi-dilute (< 20% solids) conditions and three-dimensional (3D) microstructures at concentrations > 30% solids. The yield stress (σ) values determined for the fiber pulp were logarithmically related to the volume fraction of the 2D/3D structures. The relationships developed here for different ARs showed that the yield stress of a flotation pulp changes with respect to shape, size, and the concentrations of the microstructures. Implications to the effects of such entangle networks on selectivity of flotation separation are discussed.

By R. Buchan

A number of mineral processing techniques have been adopted for the separation of the plastics making up a typical beverage bottle, and a complete flowsheet developed. Thus, size reduction, heavy media separation and flotation were used to separate PE, PVC and PET from their mixtures with cellulose fibers and aluminum, which makes up the cap of such bottles. It is shown that while heavy media separation allows the separation of a PVC/PET mixture from the solid waste, froth flotation can be readily used to separate PVC and PET from a mixture of the two. For this purpose, the differential action of an alkaline aqueous solution (PH=II) which contains methanol and MIBC as surface tension control agents has been found to be a suitable flotation medium. This paper reports some aspects of the flotation flowsheet developed for the separation of plastics from municipal solid waste mixtures and PVC from PET.

Jan 1, 1995

By Fred C. Caspall

During the last century the importance of coal as a natural re- source has frequently come to the attention of the general public, but never before nave circumstances combined to focus as much attention on coal as it receives today. There is the ever increasing demand for energy that can be met only by coal consumption, coupled with a growing awareness of man&apos;s potential for despoiling his own environment. Society monitors the use of the remaining resources with an increasingly critical eye and, for obvious reasons, surface mining operations tend to draw an unusual amount of public attention. While the surface mine is a successful economic competitor with other uses of the earth&apos;s outer skin, one of the unrewarding results of such activity is tile simultaneous destruction of two of our most important resources--the coal seam and the surface soil. In a relative sense the coal seam is a nonreplaceable resource but the surface soil can be restored. Unfortunately, little attention has been given to land reclamation and even less has been devoted to the restoration of a productive surface soil. The research reported in this paper was de- signed to test the relative productivity of newly reclaimed surface mine spoils in western Illinois. The results are preliminary in nature but may aid in the future redevelopment of mine spoil soils in the Illinois Coal Basin.

Jan 1, 1975

By Rubén Pavón] [H.

Mexico, that for various years held the second place among the elemental sulphur producers in the world, now occupies the fourth position. Nevertheless, taking advantage of the recent increase in the international prices of the metalloid, it is expected that Mexico recovers its traditional position producing, for the first time, over two million tons of sulphur during 1974. Drawing from material stockpiled during the last years sales are expected to reach 2.5 million tons, at excellent prices in the foreign markets, but not so in the domestic ones where prices have remained practically static since 1955, in spite of substantial escalation of production costs. Of the two sources of elemental sulphur in Mexico, the frasch process extraction from the salt domes of the Tehuantepec isthmus where the most important reserves are located - is the one that shall have an important increment. An increase of production of lesser magnitude is expected from sour gas, since sulphur recovery plants wilI go on stream toward the end of the year in the new oil fields recently located in the State of Chiapas. Two Mexican corporations are expanding and improving rational Frasch extraction operations. Together with Petroleos Mexicanos&apos; sulphur recovery from sour gas it is estimated that production during 1975 shall reach 2.5 million tons and, consequently, supply the domestic market and generate an important sum of foreign currencies.

Jan 1, 1974

By T. McNulty

The author was privileged to find employment as a uranium mill chemist for The Anaconda Company while working his way through school in the mid-1950s. He then served Anaconda in various technical and management positions until 1980. This paper describes the prevalent technologies employed by uranium producers, briefly describes various mines and mills in the U. S., and memorializes a few of the thousands of men and women who contributed to the U. S. Uranium Boom. Following isolation of uranium as an element by M. H. Klaproth in 1789, uses of uranium were confined primarily to pigments, glass coloring agents, and ceramic glazes. In 1896, Antoine Becquerel found that uranium is radioactive, releasing particles and energy as it decays. In 1898, Pierre and Marie Curie isolated radium from uranium and learned that it can be an effective treatment for some types of cancer. In 1939, it was discovered that the isotope U235 is fissionable1 . Up to this point, nearly all uranium production was from pitchblende concentrates made in Bohemia, Canada, and the Belgian Congo. In 1938, only about 5 percent (23.85 short tons) of global output was produced from ores of the carnotite mineral that were being mined in the U.S. By the early-1950s, physicists in many countries had begun to recognize the potential for nuclear chain reactions. Ernest Rutherford (UK), Frederick Soddy (UK), and Leo Szilard (US) explained transmutation of elements and formulated the principle of “atom splitting”. In 1934, Marie Curie’s daughter, Irène, and her husband, Frédéric Joliot, identified uranium as the most viable source for this new form of energy. The basic fission process was unraveled by German scientists in December 1938. After Hitler’s army seized the uranium deposits in Czechoslovakia, many feared that Germany would build the first nuclear weapon.

Mar 2, 2022