Search Documents

In the hierarchy of performing mine planning tasks, production scheduling is naturally at the bottom. Yet good production scheduling is probably the most demanding and difficult task to achieve for various reasons. Being the last task in the mine planning hierarchy, a proper production schedule must not only conform to both the long-range and the short- range mine plans but also satisfy many practical details that are unique to day-to-day operations. For example, the averages which were good enough for both long-range and short- range mine planning are no longer good enough for production scheduling. Instead, the variations become the overriding concern. The answer must also be obtained quickly and on time, thus adding another dimension to the overall problem. Because of these considerations, many production scheduling problems have been begging for solution during the past decade. Many attempts were made to solve the production scheduling problems in the past using computers and the available operations research (OR) techniques, particularly among academic groups. However, it is probably true that, compared with the current full-time computer usage in long-range and short-range mine planning, very little computer usage is being made in production scheduling to date.

Jan 1, 1979

By N. Djordjevic

The vibration energy that travels beyond the zone of rock breakage is wasted - all it does is cause damage and annoyance. Under favorable geologic conditions, this energy may travel many kilometers before it finally drops bellow the background noise level. This has forced the introduction of more restrictive limits to the allowable vibration levels. To maintain the profitability of a mine or quarry and to comply with environmental protection legislation, blasting needs to be performed in a more predictable way that will ensure that the final results are optimal in both mining and environmental terms. Minimization of ground and induced structural vibration is, therefore, a matter of good blasting practice - not just an attempt to avoid complaints from neighbors. A new approach to blast vibration minimization is presented. The method utilizes the existence of the local minimums in the frequency spectrum of single-hole blast vibration. The results are presented as a delay map showing maximum ground or structural vibration velocity for many combinations of interhole and interrow delays. A blast engineer can use this map to select an optimal combination of delays that will produce a low vibration velocity at a selected location and, at the same time, will be acceptable from the point of view fragmentation or muck pile shape.

Jan 1, 1997

By M. McPherson, G. Danko

Methods of measuring in situ rock thermo-physical properties are rapidly evolving. Among those existing in the literature, a particular measurement procedure was selected for further development. The measurement is based on creating a spherical temperature field in a drill hole using a point source heater of constant heat flux. The bivariate temperature distribution 0 (r, t) is measured at several points along the length of the drillhole, radius r from the heater and at particular time intervals (t). A number of different evaluation methods were tested for calculating the unknown thermal conductivity (k) and diffusivity [] from the measured temperature and the known heat flux. The results showed that evaluation using the finite difference scheme and small temperature differences measured at points close together, cannot give a reasonable result. In order to solve the problem a new general analytical evaluation method is developed. Using an appropriate technique, it is possible to simultaneously obtain values for k and [], incorporating a semi least square technique to reduce the uncertainty in the evaluation. The new device and evaluation method makes it possible to obtain from a single drill hole highly precise k and [] values within an 8 hour period. The method has been used in several underground mines in the U.S. with good results.

Jan 1, 1987

By C. Flores, R. Y. Wan, M. C. Fuerstenau, T. S. Jordan

Most oxidized manganiferous silver ores contain manganese associated with silver and are not amenable to conventional silver extraction methods, including direct standard cyanidation techniques. However, it is known that dissolution of the manganese might yield a suitable material from which silver can be recovered by conventional methods. In the segregation process, which involves heating the ore with a small quantity of salt and with a source of reducing agent to 680°C - 800°C, the silver is volatilized, migrates and is reduced to metallic silver particles. Conventional cyanide leaching is applied to the resulting calcine. Laboratory investigations have been conducted on a manganiferous silver ore analyzing 0.02 % Cu, 0.09 % Pb, 0.33 % Zn, 12.55 % Mn and 187 g/ton Ag to study the influence of roasting temperature and time, quantity of salt and quantity of coke on silver extraction by the application of segregation roasting followed by cyanidation. Cyanide leaching tests were carried out at room temperature on the segregated calcines produced by using an alkaline cyanide solution containing 2.0 lb/ton of NaCN at pH 11 for 72 hours. The results indicated that 97.8 % of silver extraction can be attained at 850°C, with 2.0 % salt, 1.0 % Coke and 30 minutes of roasting time.

Jan 1, 1993

By R. J. Lutton

The suitability of large-stone materials continues to present occasional problems in US construction. Distinctive modes of rock deterioration cracking, spalling, delaminating. disaggregating, disintegrating, and dissolving help to distinguish causes of deterioration. Design requirements, costs, and environmental factors remain critical to performance. The rating of material quality from superior hypes such as granite to marginal types such as conglomerate is too simplistic but may be useful in a preliminary way. Regardless, the market is dominated by limestone/dolomite material types because of their widespread availability. Certain tests that have been standardized are widely accepted and used for evaluating stone as riprap and armor. These tests are adapted from those used extensively for concrete aggregate; they explore the resistance of the rock to destructive processes such as abrasion, freeze-thaw, and wet-dry environmental attack. The field evaluation of the rock source is often as important as testing. Important limitations imposed by natural jointing and variations of bedding are documented in this manner. The field examination also supports the testing by estimating how much of the quarry is rep¬resented by each of the samples to be tested. Finally, quarrying and processing methods and transportation are carefully considered in regard to stone quality, average size, size gradation, and cost.

Jan 1, 1990

By Stephen R. Hunt

This paper summarizes some preliminary results of the Illinois State Geological Surveys current investigation into surface subsidence resulting from coal mining in Illinois. The purpose of the study is to characterize-the vertical movements that may result from various types of underground coal mining. In general there is relatively little published information about subsidence from room-and-pillar mining as compared with longwall mining. The findings of this study, based on mining operations in a variety of geologic settings, delineate the magnitude, shape, and position of the subsidence profile. Comparisons of case histories of subsidence are based primarily on the extraction ratio and the general geometry of the mine (depth, panel width, and mining height).

Jan 1, 1979

By Y. C. Kim, F. Szidarovsky

The technique of linear kriging as a grade estimation method of mining blocks is reason¬ably established in the mining industry. During the kriging process, negative kriging weights ([]i) are sometimes encountered. Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense. To guarantee nonnegative weights, an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of nonlinear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer, time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over-or underestimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1987

By D. A. Peterson

Laboratory testing was completed to determine the effectiveness of a fiberglass cable bolt (FCB) as a cuttable rock support for a continuous, hard-rock mining method. The FCB consists of four Polystal tendons combined in a node/antinode fashion, with polyvinyl chloride (PVC) spacers forming the anti-nodes. The largest ultimate pull-out load achieved by the FCB was 22 t (48,400 lb) at 89% of the tendons' theoretical pullout load. This premature tendon failure is accredited to: • differential stresses within the tendons and • differential tendon displacement. An increase in pull-out resistance for a given embedment length is due to: • increased bond area, • reduced interfacial shear and • "wedge" effect. The critical embedment length was found to be 40% less than for conventional steel cable bolts (SCB) at a 127-mm (5-in.) node spacing. An FCB can have up to a 92% increase in load-carrying capacity over a conventional SCB at equal embedment lengths. The load carrying capacity is equivalent to SCB at a 960-mm (37.8-in.) embedment length. Though the FCB is 7.5% more expensive than the conventional SCB (installed), this cost may be offset by increased performance. FCBs are a potentially viable support alternative for continuous hard-rock mining.

Jan 1, 1993

By H. Burger

For mine planning in the hardcoal industry the reliable prediciton of the properties of a deposit-both ahead of the zone to be worked as well as of zones at depths not yet developed - may help improve the production results of workings. With the wide spacing of exploration drillings usual in the coal industry, it is hardly possible to establish adequately reliable plans just by simple kriging methods. During the exploration phase a decision has to be made whether the zone ahead of a face area is economically profitable and, in addition, accessible and safe in order to be included in the production planning. It is, first of all, important to gather global information on certain parts of the planning area it the form of local estimates. Moreover, cut-off problems play a critical role, e.g. if there are set cut-off thicknesses as a criterion for minability or if safety aspects have to be considered. Conditional simulation appears to be a useful geostatistic method in order to localize or predict areas of potential rock burst hazard - based on geological criteria in conjunction with the guidelines by mining authorities - in the zones ahead of a working. It is a means of providing an objective basis for the evaluation and planning of mining activities.

Jan 1, 1986

By A. Cecala, J. Noll, J. Hummer

"NIOSH has observed that many control rooms and operator compartments in the US mining industry do not have filtration systems capable of maintaining low dust concentrations in these areas. In this study at a mineral processing plant, to reduce respirable dust concentrations in a control room which had no cleaning system for intake air, a filtration/pressurization system originally designed for enclosed cabs was modified and installed. Eighty-seven percent of submicron particles were reduced by the system at static conditions, meaning that greater than eighty-seven percent of respirable dust particles should be reduced. The particle size distribution for respirable dust particles are greater than for submicron particles, and filtration systems usually are more efficient in capturing the larger particles. A positive pressure near 0.02 inches of water gauge was produced which is an important component for an effective system and minimizes particles (e.g. dust) from entering into the room. The intake airflow was around 118 cfm, which is greater than the airflow suggested by ASHRAE for acceptable indoor air quality. INTRODUCTION Chronic overexposure to respirable silica dust (particle diameter < 10 microns) leads to a progressive lung disease known as silicosis. Workers who develop silicosis have an increased incidence of lung cancer and pulmonary disorders. In June 1997, the International Agency for Research on Cancer (1) found sufficient evidence to declare that inhaled crystalline silica in the form of quartz and cristobalite is carcinogenic. Mining is one of the leading industries for occupational exposure to silica dust (2-7). Control rooms located in dusty areas in some mines are of particular concern (8). Many mineral processing operations utilize operator’s compartments and/or control rooms to house workers who are performing particular job functions. Most industrial processing mills have rooms where a worker looks out over the facility and has direct control over the product flow throughout the entire building. In addition, primary crusher operators are often located in a compartment from which they are able to view the primary crushing function. Their job is to control when trucks dump into the primary jaw crusher and the rate of feed of the ore from the hopper into the crusher. Many of these control rooms and operator booths do not have filtration systems capable of cleaning air entering the control room or booth, which can result in elevated concentrations of dust in the room or booth. To reduce the dust concentrations in these rooms, it would make sense to clean the entering air with filtration/pressurization units similar to those proven to provide a clean environment in enclosed cabs."

Jan 1, 2016

By K. N. Mayfield, T. Novak

"The applications for automation continue to expand within the mining industry. These applications can range from the startup, control, and shutdown of processing plants to the autonomous operation of surface haulage trucks. However, the term “automation” should not necessarily be interpreted as the total elimination of human interventions since numerous mining processes can be partially automated. The future survivability of many mining operations will be influenced by a company’s willingness and ability to understand, accept, and utilize this technology. The mining workforce, including management and engineering, should be familiar with the technological capabilities and limitations for effectively implementing automation into mines for improving safety and productivity. The Department of Mining Engineering at the University of Kentucky has recognized this educational gap and developed an automation laboratory, along with project-oriented courses at the undergraduate and graduate levels. The laboratory and the course objectives are described in this paper, as well as the skills and abilities that students obtain at the completion of the course(s). BACKGROUND The touted benefits of automation include: improved productivity, lower operating costs, reduced drudgery of repetitive operations performed by workers, and the removal of workers from hazardous locations. The acceptance of advanced technology by the mining industry, however, has traditionally been slow. This cautious approach is understandable considering the complex and harsh conditions routinely encountered in mining operations. Bad experiences with some premature installations of newly hyped technologies may have also resulted in lingering skepticism by many mine operators. Nonetheless, with thoroughly demonstrated reliability and proven applications, automation based on programmable logic controllers (PLCs) has made significant inroads into the mining industry. Programmable logic controllers (PLCs) are the workhorses of automation. They were originally conceived in the late 1960s, long before the invention of the personal computer (PC). Initial PLC applications were directed towards sequential relay control in manufacturing plants, which subsequently eliminated the use of “relay logic” that was based on hard-wired electromechanical relays. With continuous advancements in electronics and computer technology over the years, PLCs have evolved into sophisticated and powerful devices with very stable operating systems. They are designed for deterministic logic execution with extreme consistency in timing, along with a high tolerance to temperature, humidity, and vibration (Smith 2003). Because of their robust characteristics, PLC networks now provide the backbone for most industrial automation applications."

Jan 1, 2017

By S. B. Patton

A computer model, which quantitatively utilizes the relationship between the interactive and dynamic processes of methane drainage, mining, and ventilation, is presented. The model includes simulation of the coalbed methane reservoir for prediction of gas-emission rates under the influence of degasification wells and longwall mining, ventilation network-generation, and ventilation simulation. As mining progresses step-wise through the coalbed-methane reservoir, the ventilation network is created and subsequently simulated, iteratively determining fan requirements to safely reduce methane concentrations. The model can be used to quantitatively study the effectiveness of methane degasification on the ventilation system in a longwall panel.

Jan 1, 1992

By K. C. Watts

The Silver City mining region is located in Grant County, southwestern New Mexico (Fig. 1). This area is well known, having produced large tonnages of base and lesser amounts of precious metals over the past several years. Mining within the region continues today, as well as exploration activity, which seems to have been on the increase since the recent discovery of a large skarn-associated Zn-Pb-Cu replacement deposit near Pinos Altos, a mineral district within the region (McKnight and Fellows, 1978). Because the Silver City area contains a number of mineral districts and retains promise for additional deposits, as suggested by widespread hydrothermal alteration and favorable igneous rocks, it was selected as the focus of two independent geochemical studies, both seeking to enhance anomaly-to- background contrast in order to improve our abilities to detect blind metal deposits or subtle manifestations of near-surface occurrences. The first of these independent studies involved the systematic sampling of those secondary Fe-Mn oxides that occur within coatings, selvages, and fault fillings, and then the selective extraction of these oxides from the host-rock matrix by chemical methods. The second study sought to isolate clastic Fe-Mn-rich materials from the heavy fraction of stream alluvium. The ultimate source of the clastic Fe-Mn oxides is presumed to be the same coatings, selvages, and fault fillings sought by the direct sampling of joints, but has been transported as a result of lateral erosional processes.

Jan 1, 1981

By S. K. Kawatra

In order to meet federal air pollution guidelines, it is necessary to remove a considerable quantity of sulfur from many North American coals. This may be accomplished by oxidizing the sulfur to water soluble forms, followed by washing the coal. Selective oxidation of the various sulfur forms can be accomplished through the use of a variety of types of bacteria. In this paper, the various bacteria and their requirements are described, and processes using bacteria to remove coal sulfur are discussed.

Jan 1, 1987

By J. S. Stachulak

Inco Limited operates nine underground mines on the rim of the Sudbury Basin. These operations are situated near the City of Sudbury, 589 km (365 miles) west of Montreal, and 363 km (225 miles) north of Toronto. The ores are mined primarily for nickel and copper, and the principal minerals are pentlandite, chalcopyrite, and pyrrhotite. Total ore production from underground is in excess of 51,000 tons per day. The total volume of fresh air supplied to the nine mines is six million cubic feet per minute. There are 50 main fans in operation at these mines, powered by electric motors totalling 11,200 kw (15,000 hp). The trend in metal mining during recent years towards mechanization and high-tonnage production methods has greatly increased ventilation requirements. The flow of air must quickly dilute and carry away diesel exhaust fumes, dust created by mining operations, and the fumes of the explosives used in blasting. Mechanical ventilation is required to obtain the necessary volume and control, as natural ventilation pressures alone are, for the most part, inadequate and unreliable. In the event of a mine fire or other needs, close control of ventilation is essential. There are two unique heating systems presently in operation at Inco: Creighton Natural Heat Ex- changer and Stobie Ice Stopes.

Jan 1, 1989

By D. Erik Spiller

Introduction The recovery of precious metals from ore can generally be accomplished using either gravity concentration, flotation, and/or hydrometallurgical (leaching) techniques. The objective of this paper is to show why gravity concentration can be an important part of recovery systems which employ leaching as the primary unit operation. A brief discussion of modern gravity concentration equipment is also presented.

Jan 1, 1984

By K. Kuhnhenn, G. Prommersberger

General aspects In Germany, swelling rock is mostly found in the keuper formation. Keuper is a sedimentary rock formation of varying composition. It mostly consists of fine or medium layers of clay/silt/marl/dolomite stone with intercalations of gypsum or anhydrite in strips or nodes. After disintegration of the top layers and tectonical incidents, the gypsum level, i.e. the upper [ ]

Jan 1, 1989

By Kevin Sierra, Orfelinda Avalo, Julio Guizado, Edwilde Yoplac, David Martinez

Mining tailings are slurry byproducts of mineral recovery. They generate serious environmental risks due to their toxicity when exposed to water and oxygen. Studies focus on eco-friendly alternatives for mitigating these environmental impacts. Processing these tailings enables a sustainable mineral production model through circular economy practices. This study evaluates using gold mining tailings to recover gold and produce bricks. Flotation tests obtained a concentrate with 86.66% gold recovery, containing sulfides (pyrite, arsenopyrite) and a tailing with silicates and oxides suitable for brick manufacturing and ornamental pieces. This approach promotes eco-friendly solutions and a greener approach to mining operations.

Feb 1, 2024

By Walter E. Cook

BOB FALCONER: Without further ado I&apos;m going to introduce our first speaker, Walt Cook. Walt is president of Strata Resources and is here with his business partner Joe Nenni. Joe would you stand up here. You&apos;ll be on the tag-team with Walt. Walt and Joe are in a consulting business associated with coal as well as metal and nonmetal industries. Their presentation will be on gainsharing. WALTER COOK: How many of you have gainsharing plans in place currently at your location? [show of hands] A considerable number-more than about half the room. Of those plans, how many of them do you consider as meeting your needs and being successful? [show of hands, far fewer, general audience laughter] You have all at least heard the word "gainsharing." Some of you undoubtedly aren&apos;t quite sure what gainsharing is, while others obviously have gainsharing plans in place and are looking for ways to improve them. In the short time I have now I&apos;ll be able to give you a precursory look at gainsharing and some brief ideas on where to look to improve your current plans. Over the years, I&apos;ve found that it is often best to explain gainsharing by comparing it to other forms of employee compensation

Jan 1, 1998

By Melvin W. Dadd

[One of the major problems in the purchase and sale of coal shipped in lake or ocean going vessels has always been the difficulty in obtaining a true analysis of the shipped coal?s quality because of faulty sampling by manual methods. As long as coal was sampled according to standards set up by ASTM methods designated D 492-48 there generally were no quarrels with the results obtained. However, due to varied weather conditions and because of the large number of cars sampled, there is no assurance that prescribed manual methods of sampling will always be followed. Because of this problem, the organization previously called American Coal Sales Association, now part of the National Coal Association, set up a committee compose of representatives from coal producers, coal shippers and coal consumers to study this sampling problem and to devise, if possible, a means of sampling on the high lift dumpers which could be automated so that a; true sample of the coal as loaded in the railroad car could be obtained.]

Jan 1, 1962