Search Documents

By R. L. Pienaar

Paper written on project work carried out in partial fulfilment of B Eng (Min. Eng.) degree A study was conducted to investigated and compare the feasibility of two single level extraction layouts for an intact part of theorebody of the De Beers diamond mine, Koffiefontein. Two layouts were chosen and the tonnage profile, development schedule and production ring blast layouts were calculated by applying the information acquired through a literature study. Current principles used on the mine were also applied. The first layout chosen is described as a simple straightforward layout with 6 production tunnels spaced 15 m apart, and is referred to as Layout A. The second layout, named Layout B, is described as a complex chevron layout with 9 production tunnels spaced 15 m apart. This layout has a rim tunnel situated in the kimberlite ground, which is called a chevron and this made the layout more complex than Layout A. By comparing the financial results of the two layouts, it was found that Layout B is a more feasible option than Layout A. Sensitivity analyses show that both layouts are extremely sensitive to the revenue of the projects. Therefore it is recommended that Layout B can prove to be a source of additional tonnage to add to the total tonnage profile of the mine and to extend the life of mine by 20 months, only if certain financial/economic factors improve. There is, however, still some areas of the project that need to be investigated.

Jan 1, 2006

By M. Görnerup, M. Hayashi, S. Seetharaman, C. -Å Däcker

The mould flux plays a crucial role in the continuous casting operation of steel due to its multi-functional assignment as lubricator and heat flux controller. In reality, the commercial fluxes can fall short of the expectations of the operator. In such cases, the performance of the mould flux reduces production throughput in the casting machine. This paper presents the results of a study of two different commercial mould fluxes in continuous casting of steels. The results of online sampling during casting, as well as off-line measurements in the laboratory, are presented. Mould flux powder and slag samples from the caster have been characterized with respect to melting behaviour, interfacial tension and thermal diffusivity, using various measuring techniques. An experimental technique has been developed in order to simulate the melting behaviour of a flux in the mould, which has been found to be useful for qualitative studies. A cross-sectional view of different powders reveals that up to four different material layers may exist in the bed: a loosely packed powder layer, sintered layer, semi-solid layer and liquid slag layer. It is found that the melting rate of the mould flux is dependent on the liquid slag layer thickness. Thus, in a continuous casting operation the melting rate is likely to be non-uniform with position in mould due to the difference in liquid slag layer thickness. Mould slag composition is found to be influenced by the starting powder for as long as 30 min, representing a large part of the first heat casting time. Observations of gas formation indicate that interfacial reactions between the steel and slag take place. Keywords: continuous sacting, mould flux, mould slag, properties

Jan 1, 2004

By M. Magnelöv, Du Sichen, U. Sjöström

An experimental study has been performed to investigate the behaviour and separation of inclusions at the interface between steel and slag. The study has been limited to liquid inclusions because they can be a potential problem in transient situations such as ladle changes in continuous casting of steel. Model experiments with water and silicon oils have been carried out to study the kinetics of separation of simulated inclusions at an interface. The properties of the inclusions and the slags have been varied by using different oils with different viscosities, densities and surface tensions. The effect of temperature of the liquids has also been examined. Measurements of the terminal velocity, rest time and the behaviour of the liquid inclusions at the interface have been recorded using a video camera. It has been found that the inclusions reach their terminal velocity early in the vessel and the experimental velocities differ somewhat from the values evaluated using ?intermediate law?. The results from the experiments have shown that the size of the inclusions has no appreciable influence on the rest time. Droplets of AK50 oil have been found to have considerably long rest time. A water film surrounding the droplet has been expected to be the main reason for the long rest time. The present study has also shown that the viscosity of the oil has certain effect on the rest time, but only to some extent, since viscosity has double functions. A higher viscosity provides higher resistance to the droplet entering the oil phase leading to longer rest time and at the same time damps the lateral movement of the droplet along the interface, leading to easier stabilization and shorter rest time. On the other hand, a high viscosity of the oil phase results in slow dissolution process. It has been concluded that a meaningful model of inclusion separation at the metal-slag interface must take the interfacial phenomena into consideration. Keywords: Inclusions, terminal velocity, rest time, dissolution.

Jan 1, 2004

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

In exploiting the ultra-deep, narrow reef ore bodies of the Witwatersrand, the ventilation and cooling systems within the stopes play a critical role because of high concentrations of active workers. This paper examines the heat, ventilation and cooling effects of a number of different stoping layouts for narrow reef mining in ultra-deep operations in very hot rock. The stope ventilation and cooling needs are driven primarily by the difference between the air temperature and that of the rock front being excavated. These needs depend on the face utilization, geometry, face advance (rate and direction), layout, backfill, use of water and machinery1,2,3. Detailed studies of different stoping configurations have been undertaken for mining operations extending to depths of 5000m below surface, where virgin rock temperatures approach 70°C. Extensive work has been completed with regard to evaluating ventilation and cooling requirements to maintain air reject temperatures of 28°C wet-bulb and better. This knowledge is being used to determine overall cooling requirements, reduce operational costs and maximize the efficiency of cooling systems. These issues are important when considering both the local and regional air conditioning systems and the most effective application of in-stope chilled water.

Jan 1, 2001

By P.J. Terbrugge

Open pit slope design has conventionally been effected as a bottom-up function utilizing available geotechnical information. This results in a decision criterion based on probability of failure and factor of Safety with a risk assessment being carried out on the proposed design slopes. The design approach recommended reverses the process using fault event tree decision methodology. The consequences of this approach are that acceptable risk criteria have to be determined by mine owners. Slopes are then designed by the technical staff to achieve these corporate goals. Benefits that arise from the process are that the owners take a proactive decision on the risk-benefit relationship allowing the technical staff to optimize the geotechnical exploration programme and design.

Jan 1, 2006

The modelling of lithological domains is a critical step in mineral resource and reserve evaluation. Deterministic models rely on an interpretation of the available drill hole data and expert knowledge, but do not account for the uncertainty in the spatial extent of the lithological domains. Instead, probabilistic models based on conditional simulation can be used to map the probabilities of occurrence of the domains within the deposit, which reflect the uncertainty in their presence or absence at unsampled locations. The mineral grade model is then obtained by weighting the predicted grades associated with each lithological domain by the probability of occurrence of this domain. Such an approach accounts for the continuity of the grades proper to each lithological domain and for the uncertainty in the spatial extent of these domains within the deposit. An application to a porphyry copper deposit is presented. Keywords: spatial uncertainty; plurigaussian simulation; geological control; kriging; geostatistics.

Jan 1, 2007

By C. Maree

Paper written on project work carried out in partial fulfilment of B. Eng (Chem. Eng.) This paper describes the development and use of a process simulator to optimize gypsum recovery at Afmine, a small plant near Yzerfontein on the South African West Coast. The simulator consisted of models of the major plant equipment, viz. hydrocyclones, surge bins, settling tanks, a primary sieve and a dewatering screen. Experimental data suggested that the equipment could be modelled satisfactorily from data published in the open literature. Simulation studies have indicated that gypsum losses on the plant could be reduced substantially by means of some relatively minor modifications to the plant layout. Moreover, sensitivity analyses of the plant have indicated that optimization of the settling tanks should receive priority over the other process units.

Jan 1, 2005

By T. Watanabe, S. Hayashi, M. Hayashi, K. Nagata, H. Fukuyama

Chemical states of fluorine in CaO-SiO2-CaF2glasses in a composition range of CaO/SiO2=0.5?1.3 and 5?25 mol%CaF2have been investigated by 19F solid-state NMR with and without MAS. The isotropic chemical shifts of the glasses are close to those of cuspidine crystal (59.4 and64.3 ppm with respect to C6F6) and CaF2crystal (58.6 ppm). The fluoride ions are coordinated with four or less than four calcium ions in this composition range. The chemical shifts move to the lower frequency with an increase in the CaF2content, whereas those are not affected by theCaO/SiO2ratio. The ionic distance between calcium and fluoride ions increases with an increase in the CaF2content. The chemical state of fluorine is not disturbed by the degree of polymerization of the silicate network. Comparing the MAS and static NMR spectra, the second moment attributed to 19F-19F dipole-dipole interaction has been estimated. The values of the glasses range over 3.1?7.3107Hz2andthose are larger than the calculated value of cuspidine crystal. This indicates that fluoride ions form Ca-F clusters in the glasses and that the size of clusters increases with increasing the CaF2content. Keywords: chemical state of fluoride ion, CaO-SiO2-CaF2glass, solid state 19F NMR spectroscopy

Jan 1, 2004

By H. Krogerus, P. Niemelä, P. Oikarinen

High carbon ferrochromium is produced by carbon reduction. No replacement for carbon as reductant has yet been developed. The reduction creates a considerable amount of CO-gas. In open and semi-closed furnaces the gas is burned when leaving the burden. In closed furnaces the formed gas is sucked out by a fan, washed and utilised as fuel. The formation of carbon monoxide is presented briefly starting from thermodynamic considerations up to solid and liquid state reduction. The volume, composition and energy content of the furnace gas are discussed, focusing on the raw materials and pre-treatment processes of the furnace feed as well as on the process equipment and control. Outokumpu has been using closed and sealed furnaces and utilising the CO-gas in its Tornio Ferrochrome Works since 1968. Today in Tornio with an annual ferrochromium production of 260 000 t CO-gas production is 186 million m3, representing 68 MWh an hour. At the same time the furnace power input is 95MW. About 98 % of the CO-gas is utilised, whereof 30% in the ferrochrome production itself. This paper focuses on the characteristics and utilisation of CO-gas. CO-gas is secondary energy, which on one hand saves primary electric and fossil fuel energy in ferrochromium production and, on the other, replaces other fossil fuels at the adjacent steel works. The characteristics of the fuel, requirements for utilisation as well as health and safety aspects are discussed. Utilisation of the gas has a high impact on the total dust and gaseous emissions and on the energy optimisation at the ferrochromium and steel works.

Jan 1, 2004

Sulphide minerals, such as pyrite and sphalerite, are leached by ferric sulphate. This reaction produces ferrous sulphate and other dissolved products. The ferrous sulphate is re-oxidized to ferric sulphate by bacteria. These reactions can be written as: [ ] However, in 1964 Silverman and Ehrlich proposed that this is not the only role that is played by bacteria. These researchers proposed that T. ferrooxidans enhances the rate of oxidation of pyrite above that achieved by chemical reaction with ferric sulphate at the same solution conditions. This enhancement in the rate of dissolution was proposed to occur by direct microbiological action, possibly by the extra cellular secretion of an enzymatic oxidant. Since the Silverman and Ehrlich proposal, different authors have made opposing claims concerning the action of T. ferrooxidanson pyrite. This ?direct mechanism? of bacterial dissolution of pyrite can be given by the following reaction: [ ]

Jan 1, 2000

By Y. Nakata, K. Nagata

Plasma is partially ionized gas composed of ions, electrons and activated elements at high temperature. Some flying ash from incinerated municipal waste is melted to become glass by a transfer-type arc plasma furnace. As the glass is ionic silicate, when an electric current passes through anode to cathode, ions in molten slag electrochemically react with electron in plasma at the surface of molten slag. In case of molten Na2O-SiO2, sodium ions in the molten slag carry electric current and SiO2are reduced to evaporate as SiO gas by electron in plasma. The cases of Ag+in NaNO3-KNO3molten salt and Fe2+in FeO-SiO2slag were examined. The amount of cathodic reaction is larger than that of anodic reaction and not apparently according to the Faraday?s law on the electrochemical reactions.

Jan 1, 2004

By M. Sanchez, C. Morales, J. Palacios

The slag produced in the Peirce Smith converters at the Ilo smelter of Southern Peru Copper Corporation has shown a wide range of magnetite content, which introduces an additional problem in the smelting units due to materials? recirculation. However, the operation data analysis and the application of thermodynamic concepts have made it possible to produce slag with magnetite content between 18 and 20%. The results have suggested that matte grade enhances magnetite formation while silica controls its precipitation, and they are also influenced by the increasing temperature of the slag. Thus, in order to obtain the required magnetite content in the slag, matte grade is gradually enriched in equilibrium with slag containing from 25 to 32% silica.

Jan 1, 2004

By R. Dass

Paper written on project work carried out in partial fulfilment of B. Sc Eng (Extractive Metallurgy) degree Screening is an industrial process that splits material at a specific cut size into one fraction of particles larger than the cut size and another fraction of particles smaller than the cut size. Particles are vibrated to increase the probability of them being accurately classified and to move the oversize particles off the screen surface. In conventional screening, the screen mesh vibrates with a single frequency and the particles on the screen are all exposed to this same frequency. The Ultimate Screener (see Figure 1) is a new screen technology that imparts multi-frequency vibrations to the screen mesh so that different parts of the screen surface vibrate at different frequencies. The Ultimate Screener incorporates an additional deck that holds the multi frequency adapters as shown by Figure 2. These special adapters can transform single frequency vibrations into multi frequency vibrations. When the screen motors are switched on they begin to vibrate. This vibration is transmitted to the adapters via the body of the machine. The adapters then modify the vibration to have multiple frequencies, which are transmitted to the screen surface via resonating rings.

Jan 1, 2004

By W. Bryszewski

As a result of strategic analysis in respect of the needs for air quality management a new advanced and holistic approach to air quality management process was introduced in the North West Province (NWP) of South Africa. The process is based on the principle of co-operative management. It involves both active participation of all Interested and Affected Parties (I&AP) and the holistic approach to solving problems with the underlying principles of shared ownership and sustainable development. The process consists of the followings phases: ? Industrial process quantification ? Quantification of impacts ? Formulation of the required control measures ? Definitions of certificate conditions ? Implementation of an adequate compliance management system at company level ? Ongoing co-operative air quality and system management with the strategic objective of continuous improvements The system has been successfully introduced in the North Province and proved to be an effective management tool and aids assurance of sustained environmental ability to cope with the pressure of industrial developments. The benefits and effectiveness are discussed using Hernic Ferrochrome as an example. Hernic Ferrochrome is one of the first companies, which successfully implemented this system.

Jan 1, 2004

By Alan Bye, Megan Little

Geology, and the detailed understanding of its properties, are fundamental to the optimal design and successful operation of any mine. To that end extensive fieldwork has been conducted at Anglo Platinum?s PPRust operation to collect geotechnical information both from exploration boreholes and in-pit mining faces. Since 1998, geotechnical data has been collected from over 337 km of exploration core, 7 km of exposed mining faces and more than 15 600 field and laboratory tests, in order to define the complete set of geotechnical properties for each rock type in the mining area. The geotechnical information collected is stored in two databases, SABLE Warehouse and MineMapper3D before it is imported into the Datamine mining software package. The geotechnical parameters, mining rock mass rating system (MRMR), uniaxial compressive strength (UCS), fracture frequency per metre (FF) and rock quality designation (RQD), are modelled using geostatistics to generate a 3D geotechnical block model. Data is interpolated between exploration boreholes and exposed mining faces and modelling is constrained, using wireframes, by rock type and structural features. By having detailed geotechnical information available in a 3D model that can be readily accessed and interpreted, significant production optimisations, feasibility studies and planning initiatives can be implemented. From a slope design perspective the model is used to target data deficient zones and highlight potentially weak rock mass areas. As this can be viewed in 3D, the open pit slopes can then be designed to accommodate the poor quality area before it is excavated. It also follows that geotechnical zones can be readily identified and the slopes optimised accordingly. Rather than viewing the drill and blast department as an isolated cost centre and focussing on minimising drill and blast costs, the fragmentation requirements of the comminution and load and haul business areas are studied. It is well understood that chemical energy is the cheapest form of comminution and that major downstream benefits can be derived by increasing drill and blast expenditure. 238 blasts were assessed to determine the optimum fragmentation requirements for ore and waste. Based on the study a mean fragmentation target of 150 mm was set for delivery to the crushing circuit and a mean fragmentation of 230 mm was set for waste loading from the pit. Substantial benefits have been realised in the drill and blast department by developing empirical correlations that relate the MRMR values in the geotechnical model to a blastability index, fragmentation, required powder factor and costs. As the geotechnical model can predict changes in geotechnical conditions, the blasting

Jan 1, 2007

By D. Janicijevic

This paper describes the process of scraper winch pull force measurement and shows the results of the actual winch pull force in extreme stall situations as well as during the face and gulley cleaning. It was found that by slowing down the motor and causing it to slip, torque up to 3.5 times higher than the nominal can be developed, resulting in the same increase of winch pull force. On the other hand, measurements of the actual force needed for cleaning of the face and the gully have shown that the currently used winches are too powerful. The extra torque that can be developed by the already too powerful winch motor poses a significant danger and necessitates the implementation of measures that will eliminate this risk.

Jan 1, 2008

By A. D. Pelton, Y. -B. Kang, S. A. Decterov

Computerized thermodynamic databases for solid and liquid metal, slag and solid oxide phases in the Al2O3-CaO-CoO-CrO-Cr2O3-FeO-Fe2O3-MgO-MnO-NiO-SiO2-S system have been developed by critical evaluation/optimization of all available phase equilibrium and thermodynamic data. The databases contain parameters of models specifically developed for molten slags, liquid steel and solid oxide solutions such as spinels, pyroxenes, olivine, monoxide (wustite, periclase, lime), corundum, etc. By means of the optimization process, model parameters are found which reproduce all thermodynamic and phase equilibrium data within experimental error limits. Furthermore, the models permit extrapolation into regions of temperature and composition where data are not available. The databases are automatically accessed by user-friendly software that calculates complex equilibria involving simultaneously slag, metal, refractories and gases, for systems with many components, over wide ranges of temperature, oxygen potential and pressure. A short review of the available databases is presented. The critical evaluation/optimization procedure is outlined using the Al2O3-CaO-FeO-Fe2O3-SiO2and Al2O3-CaO-MnO-SiO2systemsas examples. Several applications of the databases to deoxidation of iron and to inclusion control in steel are discussed. Keywords: thermodynamics, phase equilibrium, phase diagrams, databases, ferrous metallurgy, steelmaking, inclusion control, slags, oxide systems.

Jan 1, 2004

By K. Morita, N. Sano

Thermodynamic properties of chromium oxides in molten slags are very important for optimization of stainless steel refining processes as well as reduction processes of chromium ores. The solubility of chromite into molten slags has been found to vary considerably with oxygen partial pressure and slag composition in former studies by the authors. In the present study, activity data and redox equilibria of chromium oxides measured under moderately reducing conditions, PO2= 6.95x10–11atm, at 1873 K are summarized. For the CaO-SiO2-CrOXsystem, the activity coefficient of chromium oxide increased with increasing basicity, and the optimized slag composition for stainless steel refining is assessed as that saturated with CaCr2O4and Cr2O3usingthe phase relations determined. On the other hand, the presence of MgO and Al2O3brings about different behaviour of chromium oxide activity and redox equilibiria and the 44 mass per centCaO-39 mass per cent SiO2-11 mass per cent Al2O3-6 mass per cent MgO slag is recommended toreduce the chromium oxidation loss in the practical stainless steel refining process at 1873 K. Keywords: chromium, activity, stainless steel, AOD, VOD, oxidation loss, redox, CaO-SiO2-Al2O3-MgO slag

Jan 1, 2004

By M. L. Smith, G. Karunatillake

Lead-zinc production at MIM, Mount Isa includes three mines, a lead concentrator, zinc filter plant and lead refinery. Lead production is vertically integrated with lead-silver bullion shipped from Australia to London for refining. Zinc is sold as a concentrate. All three mines have reached varying states of maturity mining a multitude of orebodies having significant variation in grades and metallurgical recovery for three metals. Based on current levels of measured resources, the remaining project life is at least ten years. The objective is to schedule production over the life of all three mines so as to maximize the present value of the complex. Additional scheduling complexity arises out of the implementation of long-term schedules, capital expansion projects for both mining and processing, the presence of substantial inferred reserves and interactions with MIM copper production. A large-scale, time-dynamic, life-of-complex Mixed Integer Program (MIP) production schedule was formulated to optimize lead/zinc cash flow based on a detailed life of project production scheduling study. The requirements for such a study are detailed herein. The operational feasibility of the MIP solution is compared against a non-optimal approach to strategic life-of-mine scheduling. The strategic planning emphasis placed on the MIP is compared to the implementation of a life-of-mine schedules at Mount Isa using spreadsheets and other popular commercial mine schedulers.

Jan 1, 2003