Search Documents

By W. L. Van Heerden

In situ complete stress-strain characteristics of large coal specimens by W. L. VAN HEERDEN, B.Sc. Hons. (Pret.) (Visitor) The significance of ;n situ tests on large coal specimens is briefly reviewed. Tests aimed at obtaining complete stress-strain characteristics of large coal specimens with high width-to-height ratios are described. A formula for the relationship between strength and width-to-height ratios of coal pillars is proposed, and the influence of width to- height ratios on the deformation characteristics of pillars is discussed.

By Adams. M. D.

Most of the cyanide lost in carbon-In-pulp plants is due to the reaction of cyanide with base metals and sulphides during leaching. Some cyanide is also lost in the adsorption tanks as a result of oxidative and adsorption reactions with the activated carbon. The high rates of cyanide loss in the elution and electrowinning stages are atributable to hydrolytic decomposition and anodic oxidation, respectively. However, the relative amount of cyanide lost during these two stages is small for a given amount of ore treated.

Jan 1, 1990

By V. Matou?ek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007

By P. Jordan

The practice of ilmenite smelting in electric arc furnaces has been researched and published over the last few decades. An issue that has not been addressed is the understanding of the properties of ilmenite smelting reductants, and linking these properties to the subsequent smelting behaviour in the furnace. The reduction mechanism of ilmenite smelting is not fully understood, but it is believed that the Boudouard reaction plays a role. This paper investigates the behaviour of a number of reductants when reacted with CO2 at different temperatures. Keywords Boudouard reaction, carbon reactivity, reductants, ilmenite smelting.

Jan 1, 2011

By C. Norden

The purpose of this article is to show how a representative overall equipment effectiveness (OEE) measurement can be calculated for an underground coal mining bord and pillar batch process. The calculation method, the typical losses (which include planned and unplanned availability losses, coal quality losses, and process rate losses) and the underlying logic are presented and discussed. It is argued that the current traditional underground bord and pillar mining process can currently provide a maximum theoretical OEE of only 49 per cent, while a realistic benchmark target should be in the order of 37 per cent, which relates to an average of 2400 t per shift or 1.2 Mt/a. In addition, it is argued that the current bord and pillar process is the current bottleneck to further improvement past the 2400 t per shift benchmark, and that fundamental process changes will be required to eliminate this bottleneck.

Jan 1, 2012

By P. R. Mothemela

The objective of the investigation is to optimize the truck and shovel operations for pre-stripping at New Vaal Colliery by introducing campaign mining. The aim of campaign mining is to improve the efficiency of the loading, hauling, dumping, and maintenance operations which are critical to the success of truck and shovel operations. The current loading (single-sided loading method), hauling, and dumping operations at New Vaal Colliery were found to be inefficient. Time studies were used as a major indicator to highlight the inefficiency of the truck and shovel operations, and it is recommended that an improved loading configuration, hauling, and dumping operations be implemented by using campaign mining. It is also recommended that a service truck be used to maintain the pre-stripping fleet in order to reduce travelling times to the main workshop. As expected, the improved operating conditions will lead to an increase in pre-stripping production.

Jan 1, 2013

By T. J. Otto, C. Musingwini

"The objective of any mining company is to sustainably maximize the net present value (NPV) throughout the life-of-mine (LOM). The expected NPV over the LOM is calculated based on a mine plan, yet the actual value realized by the mining company depends greatly on the level of intertemporal execution against the mine plan. Consequently, a major key performance indicator (KPI) that is often overlooked in open pit mining, due to a greater focus on temporal KPIs, is the degree of spatial compliance to the mine plan. Such focus sometimes leads to short-term actions being detrimental to long-term plans. In this paper we describe the development and implementation of a spatial mine-to-plan compliance reconciliation approach for an open pit mine. Application to a case study open pit iron ore mine in South Africa indicated a significant improvement in the spatial mine-to-plan compliance, from 69% to 94% over a three-year period from 2014 to 2016. These results indicate that implementation of the proposed spatial mine-to-plan compliance reconciliation approach can contribute positively to improving the level of spatial execution and assists in improving the alignment between short-term, medium-term, and LOM plans.IntroductionThe objective of any mining company is to maximize the net present value (NPV) throughout the life of mine (LOM). However, this objective needs to be fulfilled in a sustainable manner that considers the needs of various stakeholders, including employees, shareholders, and local communities where the mines operate. The expected NPV is calculated using a mine plan as a basis. Mine planning broadly involves identifying a strategy to exploit the mineral resource in a way that maximizes value at an acceptable level of risk throughout the LOM (Tholana and Neingo, 2016).The mine planning process is a well-recognized component in the mining value chain of an open pit mine. Figure 1 reflects the relative position of mine planning within a typical open-pit mining value chain from the mineral resource to the market"

Mar 1, 2019

By C. Mueller

Automation of mining operations is pushed by cost pressure and cyclical product prices. However, until now the different types of equipment were not able to communicate electronically with each other or with central computer systems. Therefore, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ‘common electronic language’ for easy and standardized data exchange. As in other industries, this standard is expected to have significant impact on the use of automation in general and on the markets for third party components and software. The standard’s technical architecture is open and flexible for future applications. It consists of an ‘horizontal’ structure defining ‘Application Profiles’ for different types of data sets. An additional ‘vertical’ structure (‘Equipment Profiles’) implements equipment dependent definitions for each of the applicable Application Profiles. First profiles will be available for Drill Rigs. The standard bases on the XML language thus enabling easy data exchange with commercial databases. IREDES data sets may use storage media as well as networking infrastructures for information exchange. The IREDES work is carried out by the initiative members working jointly together in the IREDES work groups. It is open for participation of all interested organizations. First prototyping applications are expected to start during 2001, the first products may be available in the following year. Key words: Mine Automation; Machine Automation; Data Exchange; Rock Excavation; Standard; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Service; Quality Assurance; Control Centre;

Sep 1, 2001

By V. Matou?vek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007

By R. du Preez

Tati Nickel is currently operating a hydrometallurgical demonstration plant in Botswana, using the Activox® process developed by LionOre Technology to produce nickel cathode and a cobalt salt from a sulphide concentrate. Cobalt is extracted using Cyanex 272. This reagent also extracts all the iron, aluminium, copper, zinc, and manganese from the nickel stream. Versatic 10 carboxylic acid is then used as extractant to recover nickel from the stream, separating it from calcium and magnesium, and upgrading it to provide a suitable advance electrolyte for nickel electrowinning. However, the selectivity of Versatic 10 for nickel over calcium is limited, and gypsum formation in the extraction circuit is a problem when attempts are made to maximize the recovery of nickel. Mintek has developed a synergistic system with Versatic 10 for improved separation of nickel from calcium and magnesium. Laboratory testwork was conducted on the raffinate of the cobalt solvent extraction circuit to optimize the Versatic 10/Nicksyn? (Mintek synergist) system to be employed. Extraction and stripping parameters suitable for this stream were optimized in the laboratory and then applied on the demonstration plant. A commercial batch (0.5 tons) of Nicksyn? reagent was produced for the demonstration plant. The laboratory testwork results and the demonstration plant performance are discussed in detail in this paper.

Jan 1, 2007

By P. J. D. Lloyd

An account is given of the development of a process to concentrate gold and other valuable minerals and to produce a discardable waste. In this process, the ore is coarsely milled, a bulk flotation concentrate is prepared, and the flotation tailing is scavenged in a hydrocyclone, which returns coarse gangue, moderately coarse valuable minerals, and locked valuable minerals back to the mill. The engineering developments required by this circuit in order that it will fit underground, and the progress made towards the achievement of those requirements, are reviewed. If the waste is to be suitable for use as a backfill in a deep-level, flat tabular excavation, it should be capable of being placed hydraulically, and should have both low voidage and high rates of drainage. Such a material could be prepared by the fine screening of the overflow from the cyclone in the proposed circuit. Possible methods for the handling of the concentrate and the recovery of its valuable constituents are described. The paper concludes with a discussion of the possible benefits from the use, in deep-level Witwatersrand mines, of a system involving concentration underground, extensive backfilling using the tailings from the concentration process, and hydraulic hoisting of the concentrate.

Jan 1, 1979

A set of six design principles for rock engineering was developed by Bieniawski: design objectives; minimum uncertainty; simplicity of design components; state-of-the-art practice; optimization; and constructability. These principles translate into a ten-step design process. Although this methodology was developed for rock engineering, it is applicable to any design process, feasibility study, etc. Diligent use of such a process will ensure that a defensible design or evaluation has been carried out. Recently a ?strategic conversation? process has been identified by Ilbury and Sunter that includes the following ten steps: scope; players; rules of the game; key uncertainties; scenarios; SWOT analysis; options; decisions; measurable outcomes; and meaning of winning. A comparison of these steps with those of the design process shows a remarkable correlation. This is perhaps not surprising since engineering design is a strategic up-front issue, and front end loading in a project is critical to achieve the expected project performance. Based on the close correlation between the strategic conversation and engineering design processes, a circular design process, rather than a linear process, is proposed. The ?circle of design? better reflects the importance of review and monitoring in the two phases of successful design and implementation?defining the design, and executing the design.

Jan 1, 2009

By Stuart Marsland

"Reference materials have always been important for validating and controlling analytical methods', They have recently become even more important as quality requirements have become more stringent and customer demands for properly verified and controlled results increase. Clients, especially from the resource exploration industry demand critical validation of all results reported. Mintek has been producing geological and semi processed ore references since the early 1970's and recently due to increase in demand other manufactures have entered the South African Market.This paper describes Analytical challenges from the customer's perspective. The customer being the metallurgist, mine geologist, environmental scientist and geologists from resource companies. Reference Materials and their appropriate use and good understanding of them can aid greatly in building confidence in the results, choosing the right Laboratory for a project, deciding which set of results arc correct and providing evidence to the customer's clients that the results obtained are the very best possible.Throughout the world there are hundreds of reference materials produced by over 80 organisations and these are mainly ores, rocks, semi processed ores, metals, and many more. Mintek is one of the top 10 producers with over 75 products. Many of these producers including Mintek and their respective standards organisations belong to the ISO REMCO committee and their respective work groups. This committee's main task is to draw up guide lines for the use, manufacturing and certifying reference materials. In South Africa a mirror committee has recently had its inaugural meeting the function is to give clear mandate to the South African representative on the main ISO REMCO committee, the South African delegate bas an opportunity to influence the contents of the guides.Tile SARM program has since the year 2000 increased its sale three fold, the question is why? There is more accountability needed in our world. That means Analytical results have to be the very best possible and risks associated to them must be well quantified. Consider that the risk of wrong results of wrong decisions made from a result is trivial to laboratory, in comparison to the laboratories customers. The consequence to a laboratory could be a loss of income or some one may lose their job. To the customer he may dig up 1000 of ton's of rock with nothing in it or worse still don't mine it when the grade is high enough. This is seriol1s money."

Jan 1, 2014

By C. R. Thomas

Although stainless steels have been used to a limited extent in the South African mining industry, the metallurgical development of 3CRI2 has presented materials engineers with a viable alternative for certain materials-handling applications. The various types of wear involved in these operations are described, and an explanation is given of how 3CRI2 is able to offer advantages, particularly in wet sliding applications. Certain applications result in various types of abrasive wear, and the performance of 3CRI2 in these areas is described.

Jan 1, 1981

By K. Barlow, J. M. W. Mackenzie

Trochem (pty) Limited, which is jointly owned by Chemical Holdings Limited and Henkel Corporation of America, recently commissioned the first fatty amine plant to be built in Africa. The plant is capable of producing primary, secondary, and tertiary fatty amines with varying hydrocarbon-chain lengths. Process control Sponsored by the South African Institute of Measurement and Control, the Instrument Society of America is bringing a short course in process control to South Africa. This will be the first in a series of courses in instrumentation and process control.

Jan 1, 1982

Today's conservation thinking is becoming increasingly polarised-a widening gap that could eventually be to the overall detriment of mankind, one way or the other. In one corner, stand the disciples of the untainted wilderness, moral protectors of the natural world who subscribe to the doctrine that the fragile balance of nature is threatened by man's very existence. On the opposite side of the ring, stands the relentless developer, with the megalomaniac notion that nature is purely there to serve humanity and civilisation, under the auspices of 'progress',

Jan 1, 1996

By A. V. Z. Brink, D. M. O’Connor

Recent research into the prediction of mining-induced seismic events by the monitoring of small microseismic events at Western Deep levels Gold Mine is described. Measurement and interpretation techniques and results are presented. It was found that the occurrence of the larger events near longwall faces on the Carbon leader reef is preceded for some hours by an increased rate of microseismic emission and spatial concentration of the microseismic events in the zone of eventual failure. The research is currently being expanded with the aim of producing a practical rockburst early-warning system.

Jan 1, 1983

By M. J. Nicol, G. Cromberge

An account is given of the development of a relatively simple model that describes the kinetics of the absorption of gold cyanide on activated carbon. The model is based on the treatment of the carbon solution interface as a homogeneous boundary across which gold is transported at a rate determined by the rate of mass transport to and from the interface. Rate equations derived from this model describe the results of various kinetic experiments under continuous or batch conditions in the laboratory and on operating pilot and full-scale plants.

Jan 1, 1983

By F. H. Deist, R. P. Plewman

The history of development of analytical techniques for the determination of elastic behaviour around tabular excavations, is examined briefly. The design of a completely digital system, which appears to afford considerable improvements in speed, accuracy and versatility compared with existing analogue methods, is described in detail. The practical application of this system is illustrated by means of an actual underground problem. The results are presented, not in the form of specific solutions to the mine's problems, but as indications of the versatility and scope of the new method.

By J. A. L. Napier

The application of excess shear stress as an aid to the design of mine layout is reviewed, and the critical parameters required to describe slip on a plane of weakness are noted. A design procedure that is required to model the cyclic build-up of excess shear stress is described. A number of simple examples of mine layouts on two reef planes intersecting a fault plane are then considered to illustrate the application of the design concept and to highlight some of the pitfals that may be encountered

Jan 1, 1987