Search Documents

MR. GIBSON (continuing): In connection with the coal from this mine, I will say that it is not a very dirty coal. The vein where most of the coal comes from is about eight feet thick, and two feet from the bottom there is a small boney band about two inches thick. The breaking shot has to be placed over the, band, therefore breaking the boney into fine particles which goes off with the slack. This coal is a very good domestic coal and the slack is in great demand for various power, plants, such as sugar plants, smelters and other industries, but where this, boney is broken up and goes into the slack, it is very injurious in effect and retards the sale of the slack. Therefore the Spring Canyon Coal Company went to the expense of' building this plant, costing over $250,000, just in order to get that, two inches of boney coal out of the rest of the vein. The market in, Utah is very critical, and in order to sell coal, the product must be thoroughly clean in every way and, as Mr. Murphy says, I believe they have succeeded in making a very good commercial product. In any event the Spring Canyon Coal Company put out more coal than any other one mine during the last year, 1924, they had the largest production. I thank, you. (Applause). PRESIDENT MARKS: With the assistance of Mr. Robinson and Mr. Miller, I am sorry you could not get the pictures a little better synchronized with the story. MR. F. C. MILLER (Chief Chemist The Colorado Fuel & Iron Company, Pueblo) : We had seven slides to show eighteen different views on the screen and we did remarkably well. (Laughter.) PRESIDENT MARKS: Is there : any further discussion on this paper? MR. G. B. JONES (Mining Inspector, Victor-American Fuel Co.) : I would like to ask a question on the

Jan 1, 1926

By F. T. Baker

The Primero mine, operated by the Colorado Fuel & Iron Company, is located 17 miles west of Trinidad, Colorado, in Las Animas County. Unusually bad roof conditions, along with heavy side pressure and other conditions causing rapid decay of timbers, all combine to create a very serious timbering problem. The height of the coal averages six feet six inches. It is a heavy coking coal and has a tendency to become easily crushed and broken down in the seam. The seam lies about 35 feet below the sandstone and the intervening formation is composed of loose shaly rock, and as the coal is extracted, the air slackens this rock to such an extent that within 24 hours, roof falls varying from five to fifteen feet in height are likely to occur. Under these conditions it is necessary to use cross bar sets in both rooms and entries, and they must be spaced no further apart than three and one-half foot centers, and be maintained within a distance of three feet of the face. Rooms are spaced on fifty footcenters, and cannot with safety be driven to exceed 14 feet in width, and 200 feet in length. The large pillar must be maintained to protect from side pressure, and the rooms must be driven up and retreated with as quickly as possible to avoid the squeeze caused by the intense side and roof pressure. Best results in extraction have been obtained by driving rooms for only a distance of 150 feet. Under these circumstances, it is readily seen that timbers of small diameters cannot be utilized in timbering any development work of a permanent nature. Entries are driven nine feet wide, and special peeled piling with an average diameter of 12 inches are most commonly used. It, is necessary to use lagging between each set of crossbars . Conditions such as these necessitated an immense expenditure for mine timber. In addition to ordinary seven and eight foot props, we used a yearly average of 65,000 feet of heavy peeled piling, averaging in diameter from 10 inches to 12 inches. Annual expenditures for timber of all classes was in excess of $60,000.00. Timber costs per ton averaged around 29 cents. In view of these exceptionally severe timber conditions at Primero, the company, in 1920, had a survey made with a view of providing some remedy to this problem. A comparison of the life of main entry timber at other bituminous mines was made, and an average life of four years was established. The actual data collected at Primero indicated an average of less than two years in the manway or "return" airways, and up to five years on the haulageways or "intake" airways. While some of this timber will stand up for a much longer period than this, a close inspection will reveal in most cases that its period of usefulness is spent. It is very essential when discussing the life of timber, especially that used on, main haulageways and aircourses, that a distinction be made between the point of service, that is, the point where it is sound, serviceable and able to carry weight, and the point of breakdown or failure, where it is no longer sound and able to carry weight. In figuring the life of timber, the point of service only should be considered as timber will frequently stand for a considerable length of time when it is entirely decayed and unserviceable. The larger part of the timber used for our permanent work was Alpine Fir, or what is locally termed Red Spruce, and the supply of this I is gradually becoming depleted and has to be obtained at a point so distant

Jan 1, 1926

By P. F. Patterson

It is a well established fact that 60 per cent of all accidents in coal mines occur from falls of roof and coal at or in the proximity of the working face. Notwithstanding that this is well known, and has been frequently discussed by mining men, this seems to be the irreducible minimum. It is even said by those in a position to know that the percentage stated is increasing. With this, information before us it would seem that not enough attention is being given to close supervision at the working face, and until this is done we may expect to continue experiencing an increase in the accidents in this area. No workman generally feels that it is more important to finish loading a car of coal than to set a timber for protection, and many accidents happen from this source, not from a lack of knowledge of the dangerous conditions existing, but negligence in taking remedies necessary to remove the danger. It is true that nearly all state laws require the mine foreman or his assistant to visit each working face every day, but with the constantly changing conditions on account of the advance of the working faces, these daily visits may be entirely inadequate to discover possible dangers and prevent accidents. The obvious remedy then is closer and more systematic inspection and supervision of the working faces. Many accidents are caused in mines on account of not enough clearance between the rib and track or between timber and track. On all main haulage ways. there should be a space of at least 30 inches between the rib and track, or timber and track, and on all rooms not less than two feet should be left between the track and upright timbers.. A great deal has been said and written with regard to systematic timbering. We doubt very much the feasibility of adopting any standard of timbering that would be suitable for all roof conditions, and any such system in our opinion would not tend to cause a decrease in the number of accidents. The proper place to put up a prop, regardless of whether it conforms to any established system, is under a piece of loose roof. No habit is becoming more prevalent among miners and other mine workers than wearing gloves, principally flimsy canvas gloves, which afford no protection to the wearers and are the direct cause of many hand injuries. If gloves must be worn, and no doubt they will be as the habit has become well established, then they should be made from some heavy material and should fit the hands fairly snug.

Jan 1, 1923

By George B. Pryde

Dear Sir: Yours of July 23rd, relative to my appointment on the Safety Committee in connection with the Rocky Mountain Coal Mining Institute. As you say in your letter, "The duty of this committee is to draft suggestions as to safer mining practices with the idea of preventing disasters in coal mines." Much has been written and many suggestions made on this same subject, and it is very hard to put up further recommendations than have already been made. The disasters you mention in your letter unquestionably have direct reference to coal mine explosions, which from time to time still occur in this and other countries. As far as our Western mines are concerned, you know that sprinkling and shot firing by electricity have been very extensively carried out. Notwithstanding these precautions; we have had a few rather serious disasters in the past in these mines. I do not care to place any blame or responsibility on the companies having these disasters, but it is a fact that in each and all of them, after careful investigation has been made, that the human element has had more or less bearing on the accidents happening. From most reports that we gain, either directly or indirectly, it is very evident that investigation shows after an explosion that the rules governing one or both of the above safety measures have been somewhat carelessly or negligently carried out. Much has been written and read about rock dust sprinkling, but it is questionable if this method is doing a great deal toward the eliminating of disasters. While it is true it may have the effect of preventing propagation, still I do not believe anyone claims for it a sure preventative against initial explosions. I had occasion not long ago to visit a mine, after an explosion, in which dust barriers were supposed to be hung, and from indications it was quite evident that the dust barriers had been in operation, but they did not prevent the explosion from reaching all open parts of the mine. It is also true that profuse scattering of rock dust throughout a mine would have a beneficial effect, but there is a question arises here as to whether the sprinkling by rock dust or the spraying by water, if available, is the most effective. I am satisfied that if all coal mines are kept well sprinkled and all open workings maintained in a thorough moist condition, that the biggest factor in a coal mine explosion is in this way eliminated. There is no doubt but what the use of permissible powder, particularly if shot by electricity, has had a very marked effect on the number of disasters in mines, and if this method of shooting was energetically carried out there would be a difference in the number of explosions, both minor and Major, all over the country. Some of the recent explosions have taken place where no shooting was being done, but there is no denying the fact that the other ingredient, namely, coal dust, entered in the elements very extensively. We have read and heard of hydraulic cartridges and other patents (substitutes for powder) that were being worked out for the purpose of

Jan 1, 1923

By H. F. Nash

Coal is the basic necessity of our present-day civilization, and those engaged in the industry, whether miner, day-man, pit boss, tipple boss, superintendent, salesman or operator, have a direct responsibility to the public at large. Our country is blessed with a great supply of Bituminous coal, upon which it must largely depend for its industrial prosperity. Anthracite coal, in its relation to our economic situation, is a small factor, as its ratio of production to Bituminous coal is only about one-sixth. However, within the last ten years, electricity and oil have largely displaced the use of coal in industry, so that the use of Bituminous coal is decreasing, relatively, and the potential production of Bituminous coal has largely increased since the war. High wage scales and high freight rates make the delivered price of coal to the consumer so out of proportion to the cost of electricity and oil -and strikes make the supply of coal so uncertain-that industry is rapidly turning to electricity and oil. The energy in a ton of coal can be transported, by electric current, a distance of 250 miles for 78% of what it costs to ship the coal in bulk, by rail, in the East-and, for about 60% of what it costs in our section of the country. The use of fuel oil, distillate and gasoline, in industry, has increased by leaps and bounds. Especially was this noticeable during the strike this year, as the large packing plants in Kansas City, Omaha and Sioux City (that formerly used nothing but coal) are now practically all using oil. This also supplies to other industrial plants throughout our territory in Texas, Oklahoma, Kansas and Nebraska. Many railroads are using oil, as are also the smelters, cement plants, etc., etc. Ten years ago, 100% of the threshing in the state of Kansas was done with coal-today not over 25% of it is done through that means-and so it goes all along the line. The use of our coal is being yearly more restricted in industry. In the case of domestic consumption, the circle is also ever decreasing.' In small towns and on farms, kerosene, gasoline and wood are largely utilized for cooking. For the past four years, along any country road, it is a common occurrence to hear a buzz-saw cutting old fence posts or timbers taken from creek bottoms. Many thousands of tons of coal are displaced each year through the use of corn and cobs. In larger towns, gas plants have been installed, and many housewives use gas-in communities contiguous to natural gas, that is used for industrial and domestic purposes. The time has gone when industrial and domestic consumers or dealers are satisfied to buy anything that is black-competition among the coal-producing states is keen, and will become more so. Eastern and southern fields are turning out splendidly prepared coals of high quality, and with their lower freight rates to competitive territory, will entirely nullify the use. of our Western coal unless-

Jan 1, 1922

PRESIDENT LITTLEJOHN: The paper of Mr. Emrick will now be open for discussion for about twenty minutes. The meeting is now open for discussion. MR. EMRICK: There is some question that may have occurred to you at different times, that is how are you going to tell when the bits are properly made? A fairly good rule to go by is when the used bits come out of the mine, if half of them are bent and half of them are broken, the average is pretty good MR. GEO. B. PRYDE (Union Pacific Coal Company): I would like to ask Mr. Emrick if he has any figures as to the saving of Dower with the different styles of its. MR. EMRICK: I suppose you mean chisel point bits and pick point bits? MR. PRYDE: Yes. MR. EMRICK: So far as I have been able to learn, the only reason why chisel point bits are used is to prevent coring that might be done by the cutter chain. The pick point bit, of course, is the proper thing to use. It can be used when the position of the cutter links in the cutter chain is right. I do not know of any figures which give power consumption ratings on the use of pick point and chisel point bits, but there are tests and ratings, etc., which have been taken- which have been tested as against different bits, which have been given proper clearances against bits not having been given proper clearances, and they will run,-in their saving in power, they will run 20 to 25 per cent. MR. A. C. WATTS (Chief Engineer, Utah Fuel Company) : I would like to ask Mr. Emrick if he has any record showing the saving in power on using the alloy steel chisel bits. I know that several experiments have been made; I do not recall the figures now, but we had a very decided saving in power. MR. EMRICK: I haven't any of the records. Do you think that is because of the steel that has been used? MR. WATTS: Well, they were all sharpened by the same man and used in the same machine, and at the same shop. I do not know the composition. It is "Red Star" Vanadium that I had in mind. MR. EMRICK: I have not seen any records. Some companies are using the tool steel bits because they stand up a little bit better. MR. BENEDICT SHUBART (Secretary) : I was going to ask Mr. Emrick about that question. There is one company that does not recommend tempering the bits. They recommend using not exactly self-hardening steel, but one that is bard enough without quenching-they use 80-90-point car- bon but about a 70-point manganese, not exactly self-hardening steel, but they do not temper this at all. Will Mr. Emrick state if a steel of that kind could be worked in the bit sharpening machine that his company makes, as it

Jan 1, 1925

forated, allowing the completion of the removal of wash water. When discharged into the washed nut bin, the coal is moist but carries so little water as to not be objectionable to the trade, nor to give any difficulty from freezing during the coldest weather. The rock and bone from the primary jigs is elevated to a 15-ton bin by means of a single strand scraper conveyor 40 feet center to center operating on a 45 degree incline, carrying 12" x 5" scrapers every two feet. This conveyor travels at a speed of 100 feet per minute and has a capacity of 17 tons per hour. From this bin, this material falls into the third or rewash jig similar in all respects to the first two, which discharges the rock waste directly into a 15-ton refuse bin below and the bone into a short dewatering conveyor which delivers into a similar 15-ton bin from which the bone is taken to the powerhouse. The oversize and water from the shaker screen, the water from the dewatering conveyor for both the washed nut and bone, and the sludge and wash water from the three jigs, are delivered by launders to the first compartment of a three-compartment settling tank. Most of the coarser broken coal is deposited in this tank, from which is it continually removed by a bucket elevator carrying 8" x 5" perforated buckets operated on a 60 degree incline at 200 feet per minute, capable of delivering 25 tons per hour to the 50-ton washed coarse slack bin. The water passes successively through the three compartments of the settling tank and from thence through a six-inch pipe to a centrifugal pump, circulating 900 gallons per minute against a 32-foot head. A four-mesh screen 30" x 72" in the third compartment of the settling tank removes the chips of wood, paper, and the other trash, which otherwise would accumulate in the water. Water is provided from the camp water system, deriving water from the well located in an arroyo bed. During the summer months just passed, the water used, has been 108 gallons per ton of raw nut, or 146 gallons per ton of washed nut. The water meter had not been installed last winter, but it is estimated that operating at capacity, the washery will be found to require only about 75 to 100 gallons per ton of raw nut. It has not been found necessary, nor advisable, to attempt to dry the sludge from the settling tank, nor to save the water from leakage of the tanks and bins. The sludge from the jigs is washed into the settling tank and the sludge from the settling tank is washed through a tile drain to the arroyo. The jigs, shaker screen, circulating pump, washed slack elevator, and the rock handling conveyor, are all driven from line shafts driven by one 40 H. P. motor, each jig driven through a clutch. The belt conveyor and the washed nut conveyor, have separate motor drives of five and seven and a half H. P. respectively. The washer is housed in a corrugated iron building, which is partially heated by steam coils. One attendant is required for operation, regulating the feed of the jigs, the supply of water, removal of the rock, and oiling and maintaining the machinery. The rewash jig is operated only intermittently. About eleven per cent by weight of raw nut is removed as waste and four per cent goes to the washed slack bin. No control analyses of the products have been made; the efficiency of the plant being determined only by the physical appearance of the products; but the washery has been a source of pride and satisfaction to all those connected with it. As mentioned before, it has caused no interruption of operation and it has assisted materially in creating an unprecedented demand for ALAMO nut. MR. CHARLES: If there are any questions, I shall be pleased to endeavor to answer them. MR. LITTLEJOHN: Mr. Charles, do I understand it is the nut only that is washed there? MR. CHARLES: Yes, sir. MR. LITTLEJOHN: What did you say the size was? MR. CHARLES: Through three inch round perforations, retained on

Jan 1, 1926

It was said that the coal operators are losing a great advantage in permitting the oil producers to take the domestic market away from them. Coal is so much less expensive and more economical than oil that even the oil producers themselves are burning coal under their stills. No longer is the housewife afraid of machinery. Not only does she operate an automobile, but in her home she is used to vacuum sweepers, washing machines, refrigerators, and multitudinous devices. She is no longer machine-shy. An electrically operated stoker, if properly introduced and guaranteed with only a fraction of the enthusiasm that the oil furnace salesman shows, would get a ready reception. Several devices now on the market are much less complicated, much less apt to get out of order, than the oil burners. In place of an increased cost for the sake of convenience, the stoker will give all this convenience at a decreased cost. So said Mr. Herres. He said, however, that it must be enclosed so that the working parts are not too much in evidence. MR. McAULIFFE: While it appears possible to adapt a continuous feed to the needs of the furnace in an apartment or a house burning thirty tons or more annually, it is not yet possible to get a furnace that would satisfy the home which burns only seven or eight tons in a season. A delegate described the Garrison stoker which is designed to care for this problem. Mr. Herres said that the Pacific Coal Company had a small stoker furnace more simple than the Harrington. Pulverized coal equipment is being adapted to use in apartment houses. The stoker designed by Lloyd Garrison, State Engineer of Utah, was described, and also one which Mr. G. W. Megeath of Omaha, Nebraska, had manufactured, which Mr. McAuliffe says, is recommended only for Rock Springs coal. It was brought out that there are over forty installations of the "Iran Fireman" in Salt Lake City. For apartment buildings, there is no question as to their satisfaction. Many of the down town office buildings are so heated.

Jan 1, 1925

MR. MARGOLF: Our final speaker this afternoon before we have an opportunity for some questions for the members of the panel, is a gentleman who has spent more than 40 years in the newspaper industry. He started out as an office boy while he was still in high school. He worked his way through college working for a newspaper in Lexington, Kentucky where he graduated from the University. He has a long association with the Albuquerque Tribune but what brings him here today is in his position as editor of The Rocky Mountain News which is certainly one of our largest circulations. I think it is the largest circulation newspaper in the Rocky Mountain states. Ralph Looney, in that

Jan 1, 1982

By Geo. B. Pryde

Dear Sir: Yours of July 23rd, relative to my appointment on the Safety Committee in connection with the Rocky Mountain Coal Mining Institute. As you say in your letter, "The duty of this committee is to draft suggestions as to safer mining practices with the idea of preventing disasters in coal mines." Much has been written and many suggestions made on this same subject, and it is very hard to put up further recommendations than have already been made. The disasters you mention in your letter unquestionably have direct reference to coal mine explosions, which from time to time still occur in this and other countries. As far as our Western mines are concerned, you know that sprinkling and shot firing by electricity have been very extensively carried out. Notwithstanding these precautions; we have had a few rather serious disasters in the past in these mines. I do not care to place any blame or responsibility on the companies having these disasters, but it is a fact that in each and all of them, after careful investigation has been made, that the human element has had more or less bearing on the accidents happening. From most reports that we gain, either directly or indirectly, it is very evident that investigation shows after an explosion that the rules governing one or both of the above safety measures have been somewhat carelessly or negligently carried out. Much has been written and read about rock dust sprinkling, but it is questionable if this method is doing a great deal toward the eliminating of disasters. While it is true it may have the effect of preventing propagation, still I do not believe anyone claims for it a sure preventative against initial explosions. I had occasion not long ago to visit a mine, after an explosion, in which dust barriers were supposed to be hung, and from indications it was quite evident that the dust barriers had been in operation, but they did not prevent the explosion from reaching. all open parts of the mine. It is also true that profuse scattering of rock dust throughout a mine would have a beneficial effect, but there is a question arises here as to whether the sprinkling by rock dust or the spraying by water, if available, is the most effective. I am satisfied that if all coal mines are kept well sprinkled and all open workings maintained in a thorough moist condition, that the biggest factor in a coal mine explosion is in this way eliminated. There is no doubt but what the use of permissible powder, particularly if shot by electricity, has had a very marked effect on the number of dis¬asters in mines, and if this method of shooting was energetically carried out there would be a difference in the number of explosions, both minor and Major, all over the country. Some of the recent explosions have taken place where no shooting was being done, but there is no denying the fact that the other ingredient, namely, coal dust, entered in the elements very extensively. We have read and heard of hydraulic cartridges and other patents (substitutes for powder) that were being worked out for the purpose of

Jan 1, 1923

PRESIDENT OLIVER: May I have your attention, please, gentlemen? The Forty-Fourth Meeting of the Rocky Mountain, Coal Mining Institute is now In session. I want to say just a few words of welcome to all the delegates this morning, both old and new. There is a large group of men around here I notice who come to this meeting year after year, and it occurs to me that they must be getting something worthwhile out of these meetings, the renewal of old acquaintances, the making of new acquaintances, and the opportunity to find out what is doing in the technical end of the coal business, and what is new. So, we greet you enthusiastically and trust that you will find this meetnig on a par with all those which have gone before and. that each one of you will leave these sessions determined that you will not miss next year but will be back again. So, with that introduction, we will proceed with the business of the convention. As time is fleeing away from us, if there is no objection, I wil lentertain a motion to dispense with the reading of last year's minutes. Will somebody make that motion? MR. H: C. MARCHANT: I move we dispense with the reading of last year's minutes. (The motion was carries unanimously.)

Jan 1, 1948

By D. Harrington

E. H. DENNY (United States Bureau of Mines, Denver, Colorado) In the absence of Mr. Harrington it is my privilege to read his paper, which is in his usual, forcible and sincere style, and it is within the province of this Institute, certainly, to go into it as it concerns safety and efficiency in mining. He brings out some points in his paper that, I think, are well worth the consideration of the Institute. The figures he uses were compiled by Mr. Adams, of the Bureau, and cover a five-year period. However, examination of similar Bureau figures for a ten-year period, or any other long period on other bases brings out similar results. The figures in this paper have been based on the million hours of exposure of accidents, and the figures based on three hundred working-man-day basis, or on tonnage, brings out similar results. This paper is entitled "Accident Record in Western Mines," and it is, in a way, an amplification of Mr. Harrington's letter which was read at the Glenwood Springs Meeting.

Jan 1, 1927

By N. H. Wetzel

Railroads, attempting to increase their tonnage without adding new lines, have for some time realized there is a definite relationship between increasd haulage efficiency, and constant communication with each moving unit that operates along their roadbeds. Elaborate radio communication equipment has been devised for this purpose, and is rapidly being installed. Coal mines are faced with similar haulage problems and have sought this constant contact through the use of telephone systems, and dispatcher stations. Often the fixed mine telephone system is unsatisfactory, since the desired person is not present at the phone when needed. Dispatchers lose contact with a motorman as soon as he is out of sight, until he calls in from another telephone. The recently developed frequency-modelated radio phone which makes use of the trolleywire network in a mine as a carrying medium, permits instant and continuous contact between dispatcher and locomotives. The motorman can immediately contact another motor or the dispatcher regardless, of his motor's position on the trollywire system, whether moving or standing.

Jan 1, 1948

MR. HARRINGTON: I would like to ask Mr. Bottomley if they fire their shots while the men are in the mine? MR. BOTTOMLEY: No sir; the shot-firing law in our State requires the shots to be fired after the men are out of the mine. We fire more shots than we did under the hand method of loading. Where formerly four holes were drilled, now we drill eight, using the same amount of powder as we did formerly, perhaps a little more, but we use a slower grade of powder. CHAIRMAN LITTLEJOHN: Any further discussion, gentlemen? MR. GIBSON: Mr. Chairman, I would like to ask Mr. Bottomley, if, in his shot-firing system, as I understand it, he has a very high coal and is working something like eleven feet? MR. BOTTOMLEY: Something like that. MR. GIBSON: I read the article that you referred to. Did you use both the first and the second delay explo¬ders in shooting the coal? MR. BOTTOMLEY: We use the ordinary fuse. MR. GIBSON: That is what I wanted to find out; whether you use the delay exploders and the detonators. In Utah, we are getting away from the fuse altogether, because we do not think it is accomplishing anything to use the electric light on the cap, and' at the same time shooting with fuse. We are defeating the object we might gain in using the electric safety lamp. That is a point that might be discussed a little further. MR. E. H. JOHNSON, The Coloder Company: I would like-since it is a general opinion that mechanical loading breaks up the coal, to ask Mr. Bottomley, if he finds a larger percentage of small coal, or how much, through the use of the mechanical loaders? MR. BOTTOMLEY: We do not find any great difference. In fact, we have succeeded in improving our lump coal percentage, and that is important, because it is largely domestic. At first, when the machines were installed, the boys shot the coal too hard, and we fell down a little, about two or three per cent, the first month, in our lump percentage, and we tightened up a little and changed our methods in shooting and got on to the stunt of drilling more holes and getting a slower grade of powder. We could not load as much coal in one day as we could before, but we did succeed in in. creasing our lump coal percentage four and a half per cent over the hand method, and that is quite a factor-quite an important factor and since our domestic trade is over with, we loosened up on the shooting and we are running about the same as we did with the hand loading, maybe a half per cent more, or one per cent, but pretty much the same. MR. SHUBART: Your coal is very high? MR. BOTTOMLEY: Yes. MR. SHUBART: Have you tried sunbbing the coal before shooting? MR. BOTTOMLEY: No, we have not tried that. It is very hard coal to shoot; we have no defined cleavage in our coal. It is the worst coal I ever saw to shoot. We do not try to snub it. Formerly, as I said, the miners drilled four holes, pretty well up near the top, and then four holes down, within about three feet of the bottom. It is the same thing as a snub shot, and that we find is the best method for shooting the coal. We have not tried any mechanical device for snubbing as yet. SECRETARY SHUBART: At one mine I saw snubbing tried with a Jeffrey undercutter with a seven-foot Jeffrey bar. This mine, by the way, is very similar to Mr. Bottomley's condition. They have very high coal, so the snub cut is a small percentage. They cut a seven foot undercut and raise the machine on an eight inch tie and undercut five feet to give the effect of a snub cut, 14 inches at the front of the cut, and then six inches at the back of the cut. They made a very marked increase in lump. (The bug dust would be a small percentage of the total coal), and they increased the percentage of the slack at the same time. They found a decrease by reason of the easier shooting of about 15 per cent in their slack. In other words their nut and lump coal ran considerably higher and their slack decreased 5 per cent with the snubbing cut. Mr. Bottomley, I believe, understands those conditions.

Jan 1, 1926

MR. DICKINSON: There is an increase of dust in machine loading, especially with the McKinlay loading and cutting machine which was extremely dusty. MR. FORRESTER: Declared more dust must be expected because when loading by machinery, the coal is shot harder in order to make it easier for the machine to pick it up. He believes however, that there was less hazard because of the closer supervision possible by reason of the concentration of operation. MR. McAULIFFE: Machine loading more dusty than hand loading. D. HARRINGTON: The hazard is greatly increased by modern methods of loading. Not only do the methods increase the quantity of dust, but they also increase the rapidity of mining and the increased quantity of coal broken down causes large quantities of gas to be released. The number of motors on loading machines and conveyors add to the hazard. No more dangerous places can be found for such motors than at the working face where there is excessive quantities of pure coal dust and where there is more gas than along any other point. Regarding Mr. Herres remarks that the machine loading was safer on account of the concentration and possibility of close supervision, Mr. Harrington said he believed concentration likely to prove a source of danger rather than its preventive. At Dolomite, Alabama, a number of men had assembled, and as a result what was a relatively small explosion killed a large number of men. Concentration is not without its dangers to mine operations. MR. McAULIFFE: These arguments do not appeal to me. Few places are better sprinkled than the working places in a machine loading mine. There is. more effective supervision, and there can be more ventilation. I believe machine loading will increase safety by that very concentration that Mr. Harrington deplores.

Jan 1, 1925

By Eugene McAuliffe

The subject of my few remarks addressed to the Rocky Mountain Coal Mining Institute, "Guessing or Knowing! Which," may perhaps suggest but little to you here today. However, I am sure you will all agree with me when I say that in the conduct of a coal mining operation there should be no choice between guessing and knowing. The value of, and the results to be obtained from this Institute, its meetings and printed transactions, as well as those of other similar educational organizations, depend very largely on the mental attitude of those who constitute, through their pronouncements, the more active portion of the membership. Perhaps the most apt criticism that is now being made of the coal industry is that, to an extent possibly exceeding any other industry of similar magnitude and importance, it depends for its conduct altogether too much on "rule of thumb" and "tradition," rather than on proven practice and actual fact. The records of our coal mining association meetings bear expression of many conflicting opinions, the majority of which are sincerely put forth by those expressing same as representing the facts; the extremes expressed, however, frequently fix the question raised as one yet located in "no man's land." There are yet too many chances taken we are still "weighing pounds on railroad track scales" and measuring yards with the proverbial "bit of string." The actual expense of conducting any one of the several operations incident to the production of coal is rarely determined, and in many instances the general cost figures, prepared some weeks after the work is complete, are of that sweeping character that very little can be abstracted therefrom. Many coal companies are now making a daily cost sheet, showing the cost of labor and material in detail, as used in the several related operations,, and such is decidedly helpful, particularly to the mine superintendent and his foreman, who, without such, sail an uncharted sea; the auditor's belated monthly summary rarely ever seen by these men who are held responsible for the labor and material used. I have made reference to this situation as an accentuation of the fact that the coal industry contains more "serious minded, conscientious guessers" than does any other similar industry, although the annual cost of our product runs up well beyond the billion dollar mark, and what is more important, our industry is one that still continues to exact a heavy toll of human life. Now this brings me to the question of safety, the one question that should be, and which is, I know, uppermost in your minds. The coal mining world, engineering and operating, is now well sold on at least two things the theory of using permissible explosives and the elimination of the open light. Furthermore, the industry, particularly that portion which is located in Great Britain and the United States and Canada, are now planning vast extensions of the use of "rock" or "shale dust," both in the form of "dust barriers" and in "direct application" to entries and cross-cuts. This is well; however,, my study of past mine explosions has convinced me that the great majority of such had their very beginning in gas accumulations; frequently originating in restricted areas at the working face, in abandoned worked-out areas, or in some other certain place where ventilation is not, maintained as it should be; and that again leads me to the point where it can again be well said, that there is too much "rule of thumb," too much guessing now being done in regard to the volume of air required, and continuously furnished, in a given entry,, panel, room or area. Just to emphasize this situation, is it not a fact that the majority of mine inspectors express the ventilation conditions as measured by them, in terms of cubic feet per man employed, in each certain split, and does not the mining laws of many states yet demand a minimum of "100 or 150 cubic feet

Jan 1, 1924

Profiled on these pages are the eight RMCMl 1998 Scholarship Award winners. Six of the eight winners were present as guests of the lnstitute at the June convention at Snowmass Village, Colorado. Each received recognition at the Institute Awards Luncheon Sunday. June 28. 1998. Each state vice president served as host for the collegiate winner and his firm provided travel and hotel expenses. In addition to receiving a plaque from the Scholarship Chairman, Jim Mattern, each winner receives $1.000 tuition credit for the coming academic year, as well as transportation, hotel lodging and meals at convention as guests of the Institute. Because this IS a continuing award, the winners from the previous year also receive a $1,000 tuition credit in their senior year if recommended by the dean of the college or university and if they remain full time students. A resident from each of the eight RMCMI member states is selected from among Board approved institutions. Criteria for these awards made annually is that the recipient (1) Is a full time sophomore student who will use the tuition credit during the junior year. (2) Be both a U.S. citizen and a resident of the member state. (3) Maintain good academic standing, be pursuing a degree in a mining related field and have an expressed interest in western coal as a possible career path. The scholarship program includes curricula other than in the mining departments, but in engineering disciplines, such as geology, mineral processing and metallurgy. Through annual donations of $100 or more. the Patrons of the Institute fund the scholarship program. A listing of current donors is found elsewhere in this book. Donations to this worthwhile program are payable to RMCMl Patrons and may be mailed to the RMCMl Office, 3000 Youngfield Street, Suite 324, Lakewood, Colorado 80215. Profiles of the 1998 Scholarship Winners follow. [ ] ARIZONA WINNER Christopher L. Delp University of Arizona Christopher is the son of Drusilla and John Delp of Tucson. He is pursuing a degree in Mining Engineering as a junior at the University of Arizona. He enjoys outdoor sports including skiing, mountain biking, golf, and hiking. He also enjoys reading, ghost town and old mine exploration, computer, Japanese conversation, and sketching cars and other forms of transportation. Chris hopes to attain a Masters Degree. [ ] COLORADO WINNER Matthew D. Lengerich Colorado School of Mines Matthew, the son of Judy Lengerich, Durango, Colorado and Ronald Lengerich of Redlands, California, is pursuing his degree in Mining Engineering with a 3.93 GPA. He is a member of the National Honor Society and the German National Honor Society. An avid outdoorsman, Matt also finds time to pursue music and theater. He was unable to attend convention this year as he was on a collegiate trip to South Africa. He is Co-President CSM Newman Group and Youth Leader at Christ on the Mountain Catholic Church.

Jan 1, 1998

By C. H. Trik

Any article or discussion on the ventilation of Working Faces under different systems of concentrated mining is of little value to any practical man unless based upon facts gleaned from actual experience, and empirical data on this subject is, to say the least mighty scarce. Of this one thing, however, you can rest assured, the old cry of "no air at the working faces" will have become a thing of the past. No longer will we hear of some operator who has been too eager to get out the coal and who has lost sight of everything else in his mad dash for production, digging himself shut until his airways are mere pin- points and his air current a feeble thing, too weak to combat the high resistance of his restricted mine. A mine operating under one or more of the various systems of concentrated mining should always have plenty of air, for in concentrated mining the tendency is toward greatly reduced mine resistances due to increased sectional areas. It can readily be seen that the tendency is to large, wide areas across the panel and where this is true large volumes and low gauges are the rule, unless inordinate restriction is encountered in the permanent airways, and no operator, far sighted or progressive enough to adopt this system of mining when his conditions permit, would ever allow his main airways both intake and return, to be anything but model courses. As a matter of .fact, we are likely to encounter the opposite of what is usually the case in most mines to day. We are apt to find the air at the working faces sluggish due to the large areas of passage rather than to high resistance. This is combated in. various ways which will be discussed further along in this article. Those companies, of which we have knowledge in this country who, to- day are using any of the new systems of mining, seem to proceed alike in the general method of developing their acreage. Let us assume, for this discussion, the Utah Colorado Coal Corporation is going to open a mine under the new system and their conditions are such as to permit their adopting the simple block system, each face served by a separate machine, each entry having its conveyor to the cars. After the permanent haulage and airways are driven "narrow work" starts to shape the blocks. We are not interested in the length of these "conveyor headings" since we do not need to drive breakthroughs nor build stoppings for ventilation until we have reached their end when we connect them together. We have two methods of sending air to the face of these dead ends. We can laboriously and expeilsively install brattice cloth, as we go, or we can use a small auxiliary blower with canvas tubing to the face. Indeed I may say that one of the great difficulties encountered under the new systems is in the ventilation of these narrow faces. After they have been connected and an air circuit or current established, ventilation becomes plain sailing until the block is worked out. The auxiliary blower when used with flexible canvas tubing, has been found to be the ideal answer to the question of how to ventilate the headings which are anywhere from 100 to 1,000 feet long. These small blowers when properly used, can go a very long way to assist in further reducing the cost of production already assured by the new method of mining. Right angle bends are made by the tubing manufacturers to enable the fan to sit in the fresh air current, yet out of the way of operations and any recirculation is positively avoided by blowing the air around the corner to the face.

Jan 1, 1926

By Franklin P. Wood

Unnumbered ages have passed since the time when nature's laboratories were working without the aid of capital or labor unions assisted only by earth's cooling crust and old Sol's rays, to lay the prodigious coal beds of the earth and distil the oils which now furnish the basis for the world's great industries. Strangely enough rays from the same old sun probably somewhat diminished in intensity are still drawing from earth to clouds the water that will run down hill and through man-made devices produce energy to compete with that made with the products created in ages past. So now we find that within the past century vast human industries have grown up around the products of these agencies and here we are today discussing the many problems connected therewith and among the others the subject of this paper, which is essentially the relation of COAL to OIL in industry. The problems involved are those of human relationship and are not fundamentally unsolvable when engineering skill and knowledge is properly applied. The last few years has developed a brand of pessimism that is especially prevalent in the coal industry, at any rate in the west where we come in contact with it. In any general discussion with coal men, a very short time only is required to bring out the feeling or expression that the coal business is on the rocks and the reasons run the gamut of human deviltry. We have heard that in the not far distant past corn was so cheap that the farmers were compelled to burn it and thus deprive the coal mines of their well earned right to sell coal for this purpose. We have heard that the flood of oil is so vast that it was being burned in preference to coal, and to heap insult on injury that the rail- road locomotives were burning oil in order to pull coal away from the mines. We have heard that the union was responsible for all the woes to which the industry is subjected. We have heard that the family tin lizzie is so depleting the family exchequer that coal could not be purchased and if purchased could not be collected for. We have heard that producing mines are so numerous that the profits are a negligible quantity. These are but a few of the reasons assigned for making the coal producers a class of pessimists which is not good for the industry. All these reasons given and all the others must be taken collectively and these are not the cause but the effect of a rapidly changing civilization. An analogy may be found in the experience of many of us in the electric industry a few years ago. You may remember that less than 20 years ago the high efficiency Tungsten electric globe was introduced. It was so much more efficient than the old carbon lamp that only one-third of the current previously required was needed to produce the same illumination. Consternation seized the ranks of electrical men who had little or no vision, for the out- look was that so little current would be sold that everyone would be bankrupt. This limited vision, however, did not prevail, for all engaged in the industry spurred on by necessity, accomplished many of the things that we are now enjoying the fruits of be- cause the electric industry has grown and is growing by leaps and bounds and every highly efficient improvement is greeted with rejoicing. It is well known that when the old type of carbon arc lamp began to be replaced by modern units the manufacturer of carbon rods thought his doom was sealed and yet these same manufacturers have so adjusted them- selves to conditions that the dry battery business of today is of vastly greater volume and profit than was the carbon rod business of the past. Of course, there are industries that should not have survived anyway that have gone down and out to makeway for vastly improved conditions and can

Jan 1, 1925

By T. H. Brien, O&apos

At nearly all of the copper smelters in the Southwest, at some time, calculations have been made having in view the economy of replacing fuel oil with pulverized coal as a heat-producing medium for smelting operations This matter has been, and is more so now than at any time heretofore, of very great importance. Due to the intensive development of oil-producing areas of the world and the tremendous use of fuel oil for many purposes, it seems that before many years the supply of oil will become so small as to prohibit its use for such operations as smelting. This may be caused by prohibitive prices, or even by government decree as a conservation measure. In the event that the use of fuel oil becomes out of the question, the copper companies have just two alternatives: the use of pulverized coal or electricity. The copper companies of the Southwest produced an average of 808,400,000 pounds of copper per year for the war years of 1916, 1917 and 1918. This figure is, of course, a higher one than has prevailed since the war, but at the present time nearly all of the mines and smelters are getting back to capacity. There is no doubt whatever that the consumption of copper is going to increase, perhaps for the next ten years. This means that more copper mines will be discovered and developed, and that the mines which are now producing will be called upon for a greater production. This all tends to show that the mine manager who is looking ahead must develop some substitute for fuel oil in the event of its use becoming prohibitive, and all indications seem to point in that direction. The only coal which is commercially available to the smelters in the district under discussion must come from Colorado and New Mexico. These coals are high in ash and volatile matter and comparatively low in calorific value. The proximity of the smelter to the coal mines is a large factor in determining which fuel is more economical. Most of the smelters within two or three hundred miles of the coal mines find it more profitable to burn coal, while those at greater distance find that the higher freight charges on the coal make the use of oil more economical.

Jan 1, 1923