Search Documents

Large quantities of combustible materials are often found in underground metal and nonmetal mines, with support timber predominating. Wood lagging and timber, wires and cables, brattice cloth, hose, paper products, cardboard cartons, and wooden containers are additional combustible materials commonly found in underground storage areas. Shorted or overloaded electrical cables, worn sockets and plugs, spontaneous combustion, careless smoking, and welding and cutting are common fire ignition sources. Inexpensive, reliable fire detection and suppression systems are available to provide early warning and to extinguish fires that originate in underground storage areas.

Jan 1, 2011

By P. J. Dallimore

The Bureau of Mines has calculated general time-dependent solutions for radon diffusion from cylindrical and slab rock samples containing uniform radium distribution. Results have been obtained for several sets of boundary conditions. The method is suitable for determining the effective diffusion coefficient and the effective porosity for radon.

Jan 1, 1983

By H. E. Powell

Because of increasing consumption of high-and super-duty refractories, the Bureau is studying the feasibility of beneficiating submarginal and marginal clays. Diverse mineral dressing tests were used to beneficiate samples from the east-central Missouri fire clay district. Standard ASTM tests were used to determine refractory properties of both crude and beneficiated clay samples. Marginal and submarginal clays containing impurities were effectively beneficiated by both wet-cyclone and wet-table treatment, but the wet-cyclone treatment was cheaper. Ion-exchange resins in the hydrogen form will probably prove more effective in removing potassium, the only alkali in Missouri fire clays to be a problem. Resins with greater cross linkage are more effective than resins with less. Roasting the crude clays before removing alkalis by chemical leaching was ineffective. By applying ultrasonic energy at a frequency of 10 to 25 kilocycles to aqueous suspensions of the clays, subsequent ion-exchange extraction of potassium was slightly improved. Higher frequency ranges did not help.

Jan 1, 1963

By J. E. Pahlman

One of the goals of the Bureau of Mines is to develop metallurgical pro-cesses that conserve energy and/or that take advantage of abundant domestic energy sources. Western lignites and subbituminous coals can be used for firing pellet induration and metallization furnaces. However, the refractory linings of these furnaces must be able to withstand attack from corrosive alkali metal oxides present in the ash of many of the low-rank fossil fuels. The Bureau of Mines conducted dynamic and static slag tests on high-alumina and alumina-silica refractories to determine their resistance to lignite ash slags. The investigations showed that increased alkali content in the lignite ash caused increased corrosion and erosion of the tested refractories. The degree of corrosion decreased with increasing alumina content, with the 99-percent-alumina refractories having the highest resistance. In general, the matrix phase was attacked preferentially to the alumina grains. Also, porosity reduction and tar impregnation enhanced the corrosion and erosion resistance. The 90-to 99-percent-alumina refractories are recommended for use as furnace linings in alkali slag environments.

Jan 1, 1979

Synthetic dawsonite [NaAl(OH)2C03] has been prepared with crystallinity similar to that of dawsonite found in oil shale deposits of the Piceance Creek area of Colorado. Optimum experimental conditions were as follows: Na/Al atomic ratio, 43; temperature, 175° to 200° C; pCO2, 15 psig; and reaction time 5 hr. Chemical and spectrographic analysis revealed that the synthetic dawsonite was of high purity and Has essentially stoichwmetric. Similarity of the synthetic to natural dawsonite, demonstrated by X-ray diffraction, infrared spectrophotometry, and electron microscopy, suggests its suitability as a standard.

Jan 1, 1972

By H. E. Powell

The selective recovery of nickel and zinc from a waste phosphate solution by solvent extraction was investigated by the Bureau of Mines as part of a broad program to recover valuable metals and compounds from industrial wastes, and to reduce the associated land and water pollution caused by dumping these wastes. The waste, which resulted from the phosphation of automboile bodies, yielded 99 percent of both the nickel and the zinc by extraction with dinonyl naphthalene sulfonic acid (DNSA) and di-2-ethylhexyl phosphoric acid (EHPA), respectively. Dilute sulfuric acid was used to recover the metals and regenerate the solvents.

Jan 1, 1970

By Charles L. Kimbell

Available statistics on 1989 worldwide consumption of selected nonfuel minerals shown in table 5 show increases for 11 of 14 listed nonfuel mineral commodities with 1 unchanged from the 1988 level, a departure from the pattern of the past 2 years, in which each of the listed commodities registered gains. The 1989 results, however, were better than those for 1986 when only seven listed nonfuel mineral commodities recorded gains with one un- changed from 1985. Consumption of the two ferrous metal raw materials listed advanced as functions of increased output of pig iron and crude steel. The increase in iron ore consumption exceeded the increase in iron ore output, suggesting a slight drawdown of world iron ore inventories. The estimated in- crease in iron and steel scrap consumption was slightly greater than the minuscule increase in world steel production, but it is believed that there was little change in the ratio of iron ore to scrap in steel plant feed on a global basis.

Jan 1, 1992

By B. T. Brady

Results of a study are presented of the effect of low radial reinforcement pressure on the postfailure characteristics of two types of granite, a sandstone, and marble. The low radial reinforcement pressure is applied to the rock surface by a gooch rubber sleeve. The gooch rubber sleeve provides a radial pressure of less than 1 psi pressure to the rock surface. This method of support gives an average strength increase of approximately 8 percent to the fractured rock sample.

Jan 1, 1973

By R. H. Grau, S. B. Robertson, R. B. Krog, T. P. Mucho

Stone mines represent the highest percentage of operating underground nonmetal mines in the United States. With the introduction of stricter Diesel Particular Matter (DPM) regulations, large-opening underground room-and-pillar stone mine operators are faced with implementing one or more alternative methods to reduce concentration levels including: install and maintain an effective ventilation system; install lower DPM emission diesel engines; the adding of DPM filters. The National Institute for Occupational Safety and Health (NIOSH) is actively researching various aspects of fan and stopping designs in an effort to improve the ventilation of these mines. NIOSH has identified and further developed three alternative ventilation methods for use in large-opening underground mines: split-mine, perimeter, and unit-ventilation. This paper describes the implementation of the three methods with respect to their use in mines of various levels of development.

By E. Morrice

High-purity lanthanum metal was prepared by electrolysis of La003 in a LaF3-LiF-BaF2 bath at 950° C. The requisite bath temperature for the deposition of molten metal was maintained by supplying the heat as current directly to the electrodes. A current efficiency of about 60 percent was obtained. The lanthanum nodules contained carbon and oxygen as major impurities. The total impurity content was from about 0.1 to 0.2 percent.

Jan 1, 1962

By James A. West

THE South Asian countries of India, Ceylon, Pakistan, Afghanistan, Nepal, Bhutan, and Sikkim have a large variety of mineral resources; however, in spite of mineral industry growth during 1964, development of resources remained far short of possible development, and, in terms of value of trade in minerals, the area remained a sizeable net importer. India's mineral industry is by far the most significant; its minerals production in 1964 accounted for more than 90 per cent of the total value of all minerals produced in the area. The total value of all minerals produced in South Asia in 1964 was only about 1 percent of the area's estimated gross national product of $55,125 million. Despite the rather small current contribution of minerals to the economy, development of mineral resources figures prominently in plans for the industrial development of the nations of this area.

Jan 1, 1966

By M. M. Fine

In an experimental study by the Bureau of Mines, in cooperation with National Lead Co., the roast-flotation process was found to be an effective means of upgrading certain cobalt-nickel stockpiles. The research was undertaken to determine whether the process could yield an enriched feed, with a minimum cobalt content of 6.0 percent, for the company refinery. The stockpiles (products of the company Fredericktown, Mo., milling operations) were essentially complex sulfides of cobalt, nickel, copper, lead, and iron, 1 sample of which contained 2.84 percent Co and 3.57 percent Ni. After a controlled oxidizing roast at 400° C., laboratory flotation with conventional sulfhydric reagents yielded an enriched concentrate analyzing 9.22 percent Co and 11.43 percent Ni, with recoveries of 84.9 and 85.8 percent, respectively. These are typical laboratory data; other data indicated higher grades were possible but at reduced recoveries. A brief, continuous campaign verified the applicability of the process to the raw material in question but was not continued long enough to establish optimum conditions. As a consequence, the results of the large-scale tests did not equal those obtained in the laboratory but definitely confirm the beneficiation possible from the roast-flotation process.

Jan 1, 1958

By M. M. Fine

This report describes a Bureau of Mines technical feasibility study of simultaneous reduction and induration of pelletized iron ore to make a product with superior qualities as blast-furnace feed. Highly reduced, physically competent pellets can be made from magnetite and specularite concentrates that contain small additions of bentonite as binder. In batch tests, pellets were dried, surrounded with solid fuel in crucibles, and heated to the reducing temperature. Total iron content of the best products was higher than 80 percent and crushing strength of 1/2-inch metallized pellets ranged up to 600 pounds or more. Comparative tests of several commercial oxide pellets showed a wide range in crushing strengths, but most values were less than 350 pounds. Continuous tests in a rotary kiln resulted in the same degree of reduction, but the pellets had lower crushing strengths because of the limitations in the maximum operating temperature of the small kiln.

Jan 1, 1962

By B. E. Blair

Accelerometers of various types, velocity gages, and a displacement meter are shown to give reliable date when measuring seismic pulses generated in rock by the detonation of explosive charges. Displacement and velocity records are differentiated and shown to compare with velocity and acceleration records. Velocity and acceleration records are integrated and shown to compare with displacement and velocity records, respectively. The experimental data are shown to satisfy the scaling laws developed by dimensional analysis. Propagation laws are developed for peak amplitudes of the first pulse of displacement, velocity, and acceleration. These propagation laws are shown to be independent of the gage used to obtain the data. As a result, the usefulness of the various gage types can be extended. For example, accelerometers, because of their high frequency and amplitude limits, can be employed near the shot to measure acceleration and/or velocity (by integration), Velocity gages, because of their higher sensitivity, can be employed at relatively larger distances from the shot to measure velocity and displacement or acceleration (by integration or differentiation).

Jan 1, 1954

By J. W. Paul

This paper deals with the third phase of on extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the results public as rapidly as possible. Parts I and II of this paper were issued Serial 2621 and Serial 2647 of the Bureau of Mines in July and October, 1924. They dealt with the resistance of unobstructed entry and the resistance caused by mine cars in untimbered entry. Description of the Tests After the resistance of unobstructed entry and of mine cars in untimbered entry had been determined by tests in the Experimental Mine, three different types of timbering were installed in the test section and the increased resistance caused by the timbering was determined.

Jan 1, 1925

By Basil Dimitriades

The association of automotive fuel composition with exhaust reactivity was studied in an experimental program that involved testing with different automotive engines and with gasolines of varied composition. Results showed clearly the exhaust reactivity to increase with increasing levels of polyalkylbenzenes in the fuel. No other systematic patterns of high significance were detected in the association of exhaust reactivity with several broadly defined groups of fuel components. For the purposes of this study, had it been possible, fuel composition should have been defined and expressed in terms of component groups such that the potential for exhaust reactivity would be the same within each group and different from group to group. Classification of fuel components in terms of the paraffins-olefins-aromatics groups does not meet the latter requirements. For appropriate classification of fuel components more information is needed on the combustion .of hydrocarbons in the multicylinder internal combustion engine. Statistical analysis of the mass emissions data showed significant car and fuel effects on hydrocarbon, carbon monoxide, nitric oxide, total aldehydes, and formaldehyde emission levels and on total photochemical reactivity. Car-fuel interactions were not significant at the 90-pct level. Correlations were found between mass emission parameters and fuel composition.

Jan 1, 1973

By H. H. Fields, Stephen Krickovic, M. G. Zabetakis, Albert Sainato

The Bureau of Mines is in the process of degasifying a virgin area in northern West Virginia from the base of an 839-foot -deep vertical borehole. An in situ gas pressure hole 199 feet long, and seven degasification holes ranging in depth from 500 to 850 feet (average 618 feet) were drilled in an 8-foot-thick virgin Pittsburgh coalbed from the enlarged (14-foot-diameter) bottom of this borehole. The in situ pressure at the back end of the hole and the range of gas and water flows from degasification holes as they were completed and closed off were 203 psi, 79,000 to 257,000 cfd (average 160,000 cfd), and 5 to 8 gpm per hole (average 6.8 gpm), respectively. Twenty-four hours after the seven holes were connected through individual water traps to a common collector for natural venting of the gas through pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psi. Eighty days later the corresponding values dropped to 529,000 cfd, 0.50 gpm, and 13 psi. After 180 days of degasification, 91 million cubic feet of gas had been removed from the affected virgin area. This represents 60 to 70 percent of the gas calculated to be contained in the area of coal affected by the holes.

Jan 1, 1973

By A. J. Kraemer

The Bureau of Mines for a number of years has been carrying on an investigation of properties of crude petroleum from producing, fields in the United States and the Western Hemisphere, and has published a series of reports on these fields, including oil fields of Oklahoma2. Acknowledgements Thanks are due to R. R. Brandenthaler and Peter Grandone, of the Petroleum Experiment Station of the Bureau of Mines, at Bartlesville, Oklahoma, who reviewed the manuscript and contributed valuable suggestions. The samples were analyzed under the direction of E. C. Lane at the Bartlesville station of the Bureau of Mines.

Jan 1, 1927

By Walter W. Fisher

A kinetic investigation of copper cementation in a revolving drum was undertaken by the Bureau of Mines to explore the effects of a porous copper deposit attached to the iron surface and a fluidized slurry of copper particles surrounding the iron precipitant. The rate of cementation was found to be significantly enhanced by the increased cathodic areas provided by a porous copper deposit or the presence of a fluidized bed of copper particles contacting the iron precipitant. The cementation rate was found to be retarded by increased ionic strength, low pH, and the presence of oxygen. The cementation reaction was first order with respect to precipitant surface area. Copper cementation on iron is visualized to occur by two basic mechanisms. Precipitation may occur through a series of shorted electrochemical cells, whereby cupric ion precipitates on a growing cathodic copper deposit, or, deposition may occur via a fluidized cathode of copper particles contacting the ion precipitant.

Jan 1, 1976

Provide longwall operators with practical information and guidelines concerning mine design to reduce problems associated with the interaction of adjacent workings in multiple-scam longwall mines. Background The high productivity achieved by longwall mining demonstrates its potential to provide a substantial segment of underground coal production. Longwall mines produce more than 30 pct of underground coal, up from pct just 15 years ago. However, the continued growth of this mining method without appropriate multiple-seam planning may increase the cost and risk of mining. Research by the U.S. Bureau of Mines (USBM) indicates that 25 longwall mines (32 pct of the total number in the United States) have mining in adjacent coalbeds either above or below. About half of these longwall mines report some type of interaction problem with the adjacent workings, such as caving due to subsidence. Optimization of mine design factors is the best means for controlling interactions between operations in adjacent scams. To avoid higher mining costs, operators should focus on adopting practices and procedures that prevent and control interactions in multiple scams. The USBM, in an effort to improve longwall mine planning, has been investigating multiple-seam longwall design and development.

Jan 1, 1994