Search Documents

By E. G. King

Cerium and thorium sulfides have found use as crucible materials for melting certain radioactive metals. However, thermodynamic treatment of these sulfides has been hampered by lack of experimentally derived entropy values. This Bureau of Mines report describes heat-capacity measurements between 51° and 298° K, and entropy evaluations at 298.15° K, for cerium monosulfide (CeS), cerium sesquisulfide (Ce2S3), and thorium disulfide (THS2). The entropy values, with Literature results for the heats of formation, are used to obtain free energies of formation at 298.15°K. MATERIALS The samples used in this work were supplied by Prof, Leo Brewer of the Department of Chemistry, University of California. The methods of preparation and some of the physical and chemical properties of these sulfides were given by Eastman and coworkers.3 4/ Chemical analyses, conducted in our laboratory, gave the following results:

Jan 1, 1959

By ROBERT R. ROUGH, FRANK L. BACON, John Dasher

(being shipped as bailast in ocean freighters). Within the last 10 years it has become more economical to use local sands, and there has been a general shift from the Belgian sand. Deposits of purer sand were treated and used for 'some time: but the suprly became limited, and means were sought to beneficiate the more bountiful subpay-f impure beach sands. These sands are composed of, 50 percent feldspar and 50 percent quartz, with small amounts of iron- bearing minerals, The most objectionable impurities in these West coast sands are the oxides of iron and aluminum. The Del Monte (Calif.) beach sand contains about 0.13 percent FeqQg and about 11.0 percent Aig03 (the latter being furnished by the large amount of feldspar present.) For the manufacture of feldspar present.) For the manufacture of flint-glass containers the maximuni quantities of these two impurities permitted in the sand are 0.05 percent F20 and 6 to 8 percent A1203.. The Fe0g occurs in the sand as follows: Traces of iron-bearing minerais resistant to weathering, ferruginous clay stains on the sand grains, and iron minerais not visible and possibly in solid solution or as colloidal incisions in the grains of feidspar or quartz. A good part of the iron in the sand is present in the traces of iron-bearing minerals, biotite, ilmenite, garnet, monazite; and hornblende. Biotite is present in larger quantities than the others. Samples of quartz, were freed of iron-bearing minerais by the use of heavy liquid (sp.gr. 2.70), leached with boiling HCI and SnCl2. Under a microscope a few apparently clean quartz grains were selected, and Fe203 was determined spectrographically to be 0.03 percent. The technique is similar to that described by Gabriel and Slavin. 4/

Dec 1, 1943

By Willard L. Hunter

The separation of tantalum and columbium by solvent extraction was under-taken as part of the Bureau of Mines research program to improve methods for extracting, separating, and reducing these elements to metal. The diethyl ketone aqueous HCl-HF system was one of several systems studied to determine the effect of metal and acid concentrations in aqueous solutions upon the transfer of tantalum and columbium into selected ketones. The tantalum-columbium oxide mixture used in this investigation was obtained by chemical extraction from Geomines slag. The investigation showed that tantalum 99.4 percent pure and columbium 97.2 percent pure can be produced by the selective transfer of tantalum into diethyl ketone from a solution of 2-N HF and 1-N HC1. The relatively low acid concentration necessary for tantalum transfer and the excellent selectivity of the system recommend its use for the separation of tantalum and columbium.

Jan 1, 1961

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

8. Refuge Chambers 8.1 Refuge Chambers - Technical Discussion 8.1.1 Introduction As a part of the overall escape system, refuge chambers can provide a last resort when existing escapeways are blocked. These chambers are intended to provide both protection from toxic gases and a life supporting environment for a period of time before external rescue or further escape efforts can be carried out Escapeways may be blocked physically (due to cave-ins, etc), by fire, or by the presence of a toxic or oxygen deficient atmosphere. In the first two cases, the trapped miners would most likely await external rescue efforts, and hence the design of the chamber will have to consider the time durations that such efforts may take, It is also possible, in the second case, for fire fighting and fire protective equipment to be stored in the chamber so that miners may attempt their own escape. In the third case, it should be recognized that a compact, beltmounted 1-hour self-contained breathing apparatus has been developed(9), and that other, less compact equipment is available for up to 4 hours of self-contained breathing supply. If such equipment were stored in the chambers, then miners could escape by travelling from chamber to chamber, taking temporary refuge in each before proceeding to the next. 8.1.2 Background The concept of "barricading" has long been recommended for those emergencies where miners are trapped inby a fire. Barricading, which is the construction of a makeshift shelter in a crosscut or deadend, protects the entrapped miners from toxic gases and enables them to conserve a supply of air. In this manner, they can survive two or three days--hopefully enough time for them to be reached by rescue teams. In the past, many lives have been saved with this technique.

Jan 1, 1976

In December's marketing of 99.5 percent aluminum ingot, domestic producer pricing remained at 53$ per pound, while dealer quoting rose from 47.5¢ to 48.5¢. BORON Domestic production of boron minerals and chemicals reached an all-time high in 1977--1.4 million short tons valued at $236 million. Combined sales of the three California producers topped the 1976 level by 15 percent in quantity and 28 percent in value, a consequence of healthy demand in the glass and insulation industries. Unprecedented demand for boric acid as a flame retardant for cellulosic insulation stimulated producers to utilize fully all available capacity, thereby achieving a record output of 158,000 tons. One company increased output from its existing boric acid facilities and initiated production at another plant that historically had produced only sodium borates. A second company achieved a previously planned 25 percent plant expansion.

Jan 1, 1978

By R. E. Head, Virgil Miller

"Under existing conditions in the treatment of oxidized lead ores containing small quantities of molybdenum no provision is made for the recovery of the molybdenum. Considerable quantities of this important element are lost in the slags of the lead smelters and constitute an economic waste. There is little or no probability that slag dumps containing molybdenum in small quantities could be economically treated for the recovery of the element, and steps for the prevention of waste in this respect must be taken prior to smelter treatment.Wulfenite, lead molybdate (PbMo04), and molybdite, molybdic ocher (Mo03), are the molybdenum minerals most abundantly found in deposits of oxidized lead ores. Wulfenite contains 39.3 per cent molybdenum trioxide and 60.7 per cent lead oxide; molybdite contains 66.7 per cent molybdenum and 33.3 per cent oxygen. Plumbojarosite, argentojarosite, cerussite, and occasionally anglesite are commonly associated with wulfenite ores, and the oxidized iron content is usually fairly high.The recent discovery and development of a body of wulfenite ore in the Star district near Milford led to a cursory microscopic examination of samples of the ore, followed by a few preliminary tests which had for their object the separation and recovery of the lead and molybdenum in separate products.The microscopic examination showed that the samples used in the work were composed of wulfenite, plumbojarosite, and a small quantity of cerussite, and indicated that the iron content was quite high. The ore was porous and yellowish-brown; crystals of wulfenite appeared to be quite uniformly distributed through it, and this mineral and plumbojarosite (Pb0.3Fe203.4S03.6H20) apparently accounted for the major part of the lead content, although lead"

Sep 1, 1928

By R. V. Ramani, C. B. Manula, A. Owili-Eger

The mine ventilation system consists of the fan, the roadways, and the regulatory devices. Sufficient fresh air must reach each working face in the mines to render harmless noxious, toxic, and respirable pollutants and to provide for the breathing of men. This is achieved by the proper selection of fan and regulatory devices. Because a mining system is dynamic, the mine ventilation system must also be dynamic. In short, mine ventilation engineers are frequently called upon to provide answers to the following questions: 1. Given a mine or the projected plan of a mine, what fan must be selected for the quantities specified in the section? At what point in its characteristic must it be operated? Are any speed changes or changes in blade settings warranted? 2. What should be the regulation in a section to insure cer¬tain desired quantity in that section? How does it affect the overall ventilation system? 3. What are the effects of driving a new shaft? Where should it be located? What size fan should be installed in the shaft? How does this affect the overall ventilation sys¬tem? 4. How much quantity increases can be obtained by cleaning up falls and streamlining roadways and by driving addi¬tional parallel airways? These questions are in no way exhaustive, nor are answers easy. Most of the operational and planning problems discussed above are to a cer¬tain extent solved by ventilation engineers using rules of thumb from experience. Both natural conditions and regulatory requirements have changed so drastically recently that use of scientific methods in ventilation planning and of faster methods in evaluating the plans is a must. Fortunately, computers offer the greatest hope for good

Jan 1, 1975

By A. Gene Collins

During recent years the interest in trace and minor constituents of oil-field water, petroleum, and their associated reservoir rocks has increased. The metals copper, nickel, lead, manganese, iron, zinc, and cadmium are not determined routinely in oilfield brine analyses. Determination of these metals and subsequent correlation of these data should yield information to aid 1n the interpretation of the origin of different waters. The methods of analyzing oilfield waters have several potential applications: (1) Aiding in the search for petroleum; (2) identifying sources of intrusive brines; (3) controlling corrosion; (4) controlling produced water; increasing knowledge of the geology of subsurface formations; (5) identifying incompatible waters in waterflooding operations; (6) increasing the knowledge of the flow of oil, gas, and water in underground formations; and (7) aiding in the identification and location of valuable mineral reserves. Some brines contain enough valuable minerals to be recovered commercially.

Jan 1, 1962

By J. R. Allsup

In cooperation with the Division of Advanced Automotive Power Systems Development, Environmental Protection Agency, the Bureau of Mines studied a conventional spark-ignition engine as a prime mover for use in a hybrid system. The study involved both steady-state and transient engine operation with ignition timing, air-fuel ratio, exhaust gas recirculation, oxidizing type catalytic converters, engine speed, and power output as variables. Data were obtained from two 1971 model 350-cubic-inch-displacement engines mounted on engine dynamometer stands. When the hybrid engine was operated with an oxidizing catalyst at power output levels required for a 4,000-lb curb weight hybrid vehicle, carbon monoxide and hydrocarbon emissions could be reduced to approximately 2.0 grams and 0.3 gram per brake horsepower-hour, respectively. With exhaust gas recirculation, oxides of nitrogen emission levels could be reduced to approximately 1.2 grams per brake horsepower-hour.

Jan 1, 1974

By Stephen A. Hare, O&apos

The melting, casting, and welding of the Raney nickel alloy (42 pct Ni-58 pct A1), a methanation catalyst useful in coal gasification, were investigated. Melting was done in graphite crucibles by heating aluminum and adding nickel using a cryolite slag cover. Casting conditions were found to be optimum when the melt temperature ranged from 1,125° to 1,200° C and the mold temperature ranged from ambient to 250° C. Suitable mold materials were found to be quartz, heat-resistant glassware, olivine, and zircon. Welding of the alloy can be accomplished using tungsten inert gas process. Tensile strength of the alloy, in the as-cast condition, was found to be 2,000 1b/sq in with an impact strength of less than 1 ft-1b. The coefficient of thermal expansion was determined to be 18.4 x 10-6/° C after heat treatment.

Jan 1, 1977

By Tobias W. Goodman, Joseph Cervik

This Bureau of Mines report investigates the horizontal trajectory of boreholes drilled in coalbeds using the rotary drilling technique. Test holes drilled in coalbeds showed that the path of a borehole in the horizontal plane depends on drilling assembly configuration, drill bit rotation, and coalbed geologic features. An assembly that contained an 18-ft (5.53) long drill collar and two centralizers had the best horizontal stability evidenced by trajectories that deviated less than 16 ft (4.9 m) from a target at 1,000 ft (305 m). Removal of one of the centralizers resulted in a loss of control of hole trajectory in the horizontal plane. Generally, holes tended to turn to the right, presumably because of right-hand rotation of the bit. Deviations from the original bearing line were as much as 200 ft (61 m) or more at a depth of 1,000 ft (305 m).

Jan 1, 1988

By C. I. Pierce

The Bureau of Mines conducted laboratory tests to determine if ultrasonic energy could reduce either the residual water or oil content of petroleum reservoir-rock samples from Appalachian area oilfields. Brine-saturated core samples were flooded with oil to residual brine saturation and subjected to 20 kilocycles per second ultrasonic energy. Then they were flooded with brine to residual oil saturation and again subjected to ultrasonic energy. Additional water displaced as a result of the application of ultrasonic energy to the flow system ranged from 0 to 4.3 percent of the original brine and averaged 1.9 percent. The increase in oil recovery as a result of the ultrasonic energy ranged from 0 to 9.0 percent of the original oil and averaged 3.1 percent. On the basis of the tests, it appears that 20-kcps acoustic waves would not have field application for oil recovery.

Jan 1, 1968

By G. T. Lineberry, W. J. Wiehagen

This paper discusses a practical method for enhancing the performance of mining work crews. The method, described as the Work Crew Performance Model (WCPM), seeks to define performance variability within similar tasks of an underground work crew. Key components of the WCPM include: (I) job definition through task analyses; (2) the ranking of job elements by perceived cost consequence; (3) observational techniques to establish performance baselines; and (4) cost linkages between adherence to task procedures and measures of consequence for noncompliance. The components of this model emphasize a reliance on learning from a veteran work force and using that information to reinvest in strategies to enhance safety and efficiency. These strategies are not limited to technologic efforts but include consideration of the so-called "soft-skill technologies" aimed at reducing variability in individual performance and at effecting a continuous improvement in overall system effectiveness.

By E. S. Longfellow, S. H. Katz

Poisonous hydrocyanic acid gas (HCN) is sometimes evolved in dangerous quantities from cyanides used in metallurgical and chemical operations. This gas is much used for fumigating buildings, ships, greenhouses, and such commodities as grain and cotton to destroy rats, mice and insect pests. Wherever cyanide fumes are evolved, thorough ventilation is necessary in order to render the sur- rounding air safe to breathe. Many persons have been killed by entering tanks and fumigated places too soon, and a simple test for this gas would promote safety. In view of the need for an easy method for quantitatively determining HCN in air, the three color reactions used originally for testing HCN in solution tions *** were modified and adapted. The reactions employ (1) picric acid (CH(NO2)3OH) which is yellow but combines with hydrogen cyanide to form a red- purple dye, isopurpuric acid****; (2) phenolphthalin (CH1604), which is a reduc- tian product of the phenolphthalein (CH4) used for acid indicator, this colorless substance is oxidized***** by presence of HCN to pink colored phenolph- thalin; and (3) guaiacum which oxidized from colorless to blue******. Phenolph- thalin and guaiacum require the presence of copper compounds which catalize the color formation by reduction of cupric cyanide. The chemical processes involved *Associate physical organic chemist, Bureau of Mines, Department of the Interior. **Assistant gas chemist, Bureau of Mines, Department of the Interior. 2014 20 *** Kohn-Abrest, E., Notice toxicologique sur les gas: Arnales des Falsifica- tions, vol. 8, 1915, pp. 215-35. (Tested air with picric acid and guaiacum papers). **** Élasiwietz, H., Ueber eine neue Zersetzungsweise der Trinitrophenylsaure: Anal. der Chemie, vol. 110, 1859, pp. 289-303. ***** Weehuizen, F., Phenolphthalin as reagent for HCN: Pharmaceutrisch weekblad, Utrecht, vol. 42, 1905, pp. 271-2. Abstract, Jour. Chem. Soc., vol. 88, part 2, 1905, p. 489. ****** Schonbein, C. F., Ueber den thatigen Zustand der Helfte des in dem Kupfer- oxydenthaltenen Sauerstoffs und ein darauf beruhendes hochst empfindliches Reagens auf die Blausaure und die loslichen Cyanmetalle: Jour. fur. Praktische Chemie, vol. 106, 1869, pp. 263-70.

Jun 1, 1923

By Ronald D. Hill, Elmore C. Grim

1.In 1972 over 595 million tons (51+0 million metric tons) of bituminous coal were mined; 49% of this tonnage was obtained by surface mining methods. Authorities have predicted that the tonnage of surface mined coal will increase in the future, especially since oil and gas resources are becoming limited. 2. Demands for clean air have increased mining activities in the low-sulfur coal deposits in the West. Pollution problems arising from these operations will be considerably different than those found in the East. The deposits are located in arid to semi-arid regions. Coal seams are generally aquifers and are a principle source of fresh water. Therefore mining may result in alteration of groundwater distribution patterns by aquifer disruption. In general, pollution problems associated with western mining are not well characterized. 3.Since any disturbance of the surface will alter the environment in the vicinity of the disturbance, pre-mining planning is a prerequisite to any environmentally successful surface mining operation. If properly carried out, the adverse social, economic, and environmental effects of coal surface mining will be minimized. Certain land areas will be unsuitable for surface mining where: a.Reclamation is not physically or economically possible. b.Mining is incompatible with existing land use plans. c.The proposed mining area is of critical environmental concern. Core drilling is the most satisfactory method of obtaining accurate information for pre-mining planning. 4. Unaccountable strip mining in the past has created problems that are still present today. Contour mining methods that involve the indiscriminate dumping of overburden on the downslope is one of the largest single sources of sediment from strip mining. However, land disturbed by strip mining can be reclaimed. Techniques have been and are being developed by which mining and reclamation are integrated into a single operation. Mountain top removal, head-of-hollow fill, and block cutting are examples in contour surface mining. These methods drastically reduce pollution problems associated with contour stripping.

Jan 1, 1974

Design, fabricate, and test a machine capable of operating in coal seams 48-inches and thicker that can reduce the time, expense, and injury potential inherent in extending and retracting mine-wide section belt conveyors, while eliminating the need to use additional machinery or equipment in accomplishing such moves. The Problem Many underground coal mines use a belt haulage system to move cut coal from the face to the loading area. This system usually consists of a main line belt conveyor fed by section belt conveyors. A shuttle car at the face carries the coal cut by a continuous mining machine to a feeder breaker that breaks the large lumps of coal into smaller, transport-able pieces and unloads them onto the tail piece of the section conveyor. This tail piece is skid-mounted so it can be readily moved as needed. The conveyor is kept close to the face during mining in order to shorten the haul distance of the shuttle cars. Section belts can be lengthened by adding belting, wire rope, and support hard-ware. During pillar retreat mining, these section belts are shortened to keep pace with pillar extraction operations. However, these belt moves, either the extensions or retractions, usually require six to eight workers and three to eight hours to complete. In addition, a 100-foot belt move requires workers to handle up to 4,000 lbs. of material, not including the tail section. Strain and sprain injuries can be incurred during this heavily labor-intensive task. The time required to move the section belt can also create losses in the mine's production. To help solve this problem, the Bureau of Mines

Jan 1, 1984

By J. E. Tiffany, Z. C. Gaugler

This supplement has been prepared to furnish information on amendments to the regulations that were approved by acting secretary of the Interior on June 24, 1946, while this report was in the press. Page 14, item 2, and page 20, item 4, have been amended by the addition of the following footnote: "Pending the development of a satisfactory multiple-shot permissible blasting unit, a blasting unit of Type II, Class A, covered by Federal Specification WB 411, December 31, 1941 (with or without Amendment 2, June 16, 1945), may be used until Decem- ber 31, 1947. Should a satisfactory multiple-shot permissible unit be made available prior to that date, this interim approval may be terminated." Page 14, footnote / has been amended to read as follows: "The use of charges over 1-1/2 pounds and not exceeding 3 pounds is approved pending further investigation. The approval, which may be withdrawn at any time, expires December 31, 1947, unless renewed. For charges over 1-1/2 pounds, the following additional requirements must be observed: (1) Shot holes must be 6 feet or greater in length. (2) Explosives must be charged in a continuous train with no cartridges deliberately deformed or crushed, with all car- tridges in contact with each other, and with the end cartridges touching the rear of the hole and the stemming, respectively. (3) The permissible explosive must be one showing toxic gas omission that will place it in either Class A or Class B."

Jan 1, 1947

By Paul S. Lewis

The Bureau of Mines hydrogenated coals of different rank that had been irradiated with either x-rays or gamma rays. Lignite, high-volatile A and C bituminous, and low-volatile bituminous coals were exposed to l billion roent¬gens of gamma-ray radiation; specimens of high-volatile A and C bituminous coals from other sources received 6 million roentgens of X-ray radiation. Irradiated and unirradiated control specimens of those coals were hydrogenated in autoclave experiments at (6,000-p.s.i. final pressure and 400° C. with retention times of 15, 30, or 60 minutes depending on the coal rank and catalytic treatment. Comparison of results from irradiated specimens with those from the control experiments showed that the radiation had no beneficial effect on the coal. High-volatile C bituminous coal may have been affected by radiation more than the other coals. One billion roentgens appeared to reduce the amount of coal converted to liquids and gases by about 10 pct., and 6 million roentgens reduced it by about 6 pct. then catalyzed with tin. In all other cases, the conversion of irradiated coal was either reduced by as much as 4 pct. or was essentially the sank as that obtained with unirradiated coal. Irradiation during hydrogenation nay be effective for increasing the reactivity of coal and should be investigated; further work with coals irradiated prier to hydrogenation is not recommended.

Jan 1, 1962

Provide guidance on the selection of millisecond initiator delays between blastholes in surface mine blasting to provide a desired degree of rock fragmentation consistent with safety and vibration considerations. The Problem Blasting remains the primary means of fragmenting, rock for all kinds of mining, quarrying, construction, and excavation activities, and it is the only practical and economic method of breaking up and moving large amounts of material such as coal overburden and stone aggregate. Because of the large amount of blasting done, typically using 4 billion pounds of explosive to break about 8 billion tons of rock annually in the United States, a small improvement in blasting performance will have a significant productivity impact. Standard blasting practices involve the selection of time delays in a blast for at [cast three purposes: (1) to control energy flow to minimize adverse vibrations, (2) to provide sufficient time relief for good rock displacement, appropriate muck pile shape for digging, and the prevention of collar violence, misfires, and flyrock, and (3) to provide an appropriate amount of interhole stress wave and gas pressure action for a desired fragmentation size distribution. Timing guidelines that exist are based on subjective observations rather than measurements, even for the relatively new casting methods. Until this Bureau study, no definitive analysis had been done to quantify the fragmentation and productivity of full-scale blast rounds as functions of precision delay timing.

Jan 1, 1989

By M. D. Schlesinger

As part of the development of processes for producing synthetic fuels from coal, the Bureau of Mines prepared a special jet fuel in a pilot plant for evaluation by the Air Force. This jet fuel had all the required physical properties, including the important specifications of high heating value and high density. However, the finished fuel did not pass the stability test specified by the Air Force and conducted by the Southwest Research Institute in a high-temperature research coker. The cause for this instability is being investigated because pure compounds of the type identified in this fuel are known to be stable. The tar acid oil used was a 230° to 300° C. fraction of low-temperature tar obtained by carbonization of a West Virginia bituminous coal in the pilot plant of the Consolidation Coal Co. Both the desulfurization at 400° C. and saturation at 300" C. were done in the vapor phase at 2,500 p.s.i.g. After catalytic treatment and distillation the final jet fuel had a boiling range of 194° to 247° C., a net heating value of 18,420 B.t.u./lb. and a specific gravity of 0.8463 60° F./60° F. It also had u pour point below -62° C., and at 0° C. its viscosity was 4.5 cs. The oil was virtually all bicyclic, 41 pct. noncondensed and 56 pct. condensed.

Jan 1, 1961