Search Documents

By J. D. Spagnola

The Bureau of Mines conducted research to obtain comparative data on the extent of reduction of galena and sphalerite with molecular hydrogen and with hydrogen from the thermal cracking of ammonia and methane at various time intervals. Galena reductions of 95 to 99 percent were obtained with H2 and with decomposed NH3 while reductions of 70 to 80 percent were obtained with cracked CH4? Sphalerite reductions of 99 percent were obtained at 1,000° C with Hz and with decomposed NBs; however, complete volatilization of the free zinc from the remaining concentrate and the subsequent recombination of zinc and sulfur vapors resulted. A promoted iron catalyst brought about a decrease of 100° C in the temperature required for complete decomposition of ammonia. It was found that H2S retards NB3 decomposition and that nitrogen retards the reduction of galena by H2? A mixture of N2 and He in about the same ratio as that obtained by the thermal cracking of NBs gave about 15 percent less reduction of galena than was obtained with decomposed NB3; this indicates that a portion of the hydrogen obtained by NBs decomposition is in an active form.

Jan 1, 1965

By W. T. Reid

A shortage of anthracite for home heating indicates the necessity of using other fuels for this purpose; low-volatile bituminous, or "soft" coal is the most feasible supplementary fuel, either burned alone or when mixed with anthracite. Comparison of Bituminous Coal and Anthracite Whereas anthracite is clean, burns without smoke, and requires little attention, bituminous coal is dusty, tends to burn with a smoky flame, and forms coke in the fire pot that must be broken up to maintain a continuous high output of heat. When properly fired, however, bituminous coal responds more quickly than anthracite to changes in damper settings and consequently can supply more heat in a short time. It is generally less expensive and usually contains less ash than anthracite.

Jan 1, 1943

By R. V. Higgins, H. C. Miller

"INTRODUCTION The development of methods for determining the total quantity of crude oil that a given pool could be expected to produce in the future and the well-spacing and drilling programs most likely to result in the recovery of the maximum quantity of oil at the minimum cost became problems of acute concern to American oil producers and petroleum engineers during the second decade of the twentieth century, The United States faced what seemed at that time to be a serious shortage of petroleum, and it appeared that the constantly increasing demand for petroleum and its products could not be adequately supplied. Undrilled prospective acreage, which until then had been plentiful, seemed to be getting scarcer, competition was increasing, the margin of profit to the producer was shrinking, and the need for developing constructive policies of conservation appeared paramount. As a result of physical and economic changes then taking place within the petroleum industry prompted by the seemingly uncertain future, accurate knowledge pertaining to the probable future production of oil wells and of oil lands especially was needed and greatly desired. Furthermore, the need for obtaining the maximum quantity of oil from known fields caused technical information - which up to that time had not been deemed essential to the successful and profitable operation of oil lands - to be sought eagerly. The need for technical information, such as methods for determining future reserves of oil and the rate at which the oil could be obtained under a specific program of drilling, was emphasized further with the passage of the Revenue Act of 1918, and oil producers with enough income to place them in the taxable class were compelled, for the first time, to report their taxable income 4/ to the Treasury Department."

Nov 1, 1939

By J. M. Stuve

Calorimetric determinations of the low-temperature heat capacities, standard enthalpy of formation, and high-temperature enthalpies were made of (Na20)4 ?Fe20,(c). The resulting values of entropy (S°), enthalpy of formation (?Hf°), and free energy of formation (?Gf°) at 298.15° K are 104.676 cal/deg mole, -656.2 ±.kcal/mole, and -603.4 A kcal/mole, respectively. Tabulations of Cp°, S°, - (G°-H°298)/T, H°-H°298, ?Hf°, ?Gf°, and log Kf are given to 1,200° K.

Jan 1, 1971

By E. M. SEELEY, F. S. LOTT

Expansion in total capacity of the natural-gasoline industry.to produce light products continued in 1944 and 1945. The average rate of gain, however, was reduced to about 6 percent annually from over 9 percent in the preceding 4-year period. New facilities at cycle plants again accounted for most of the increase in productive capacity. Between January 1, 1944, and January 1, 1946, the number of cycle plants increased from 32 to 37 and their total capacity from 3,278 thousand gallons daily to 4,848 thousand (48 percent). Capacity of all other plants in the industry increased in the same period from 12,735 thousand gallons daily to 13,080 thousand, or only 3 percent. The capacity of the average plant increased to 28,600 gallons a day from 24,400 gallons on January 1, 1944, continuing the established trend. The average capacity of cycle plants increased to 131,000 gallons a day from 102,400 gallons, and the average capacity of all other natural-gasoline plants increased to 22,200 gallons a day from 20,400 gallons. Although the number of plants increased in only three States in the 2-year period (Texas, Okla- homa, and Arkansas), the total capacity of plants increased in eight States. A further decline of 29 reduced the total number of plants to 626 on January 1, 1946. Compared with 10 years earlier, gasoline plants were more numerous in only 4 States: Texas (48 more), New Mexico (7 more), Arkansas (2 more), and Louisiana (1 more). The largest declines, in order, were in Oklahoma, Illinois, Pennsylvania, West Virginia, and California. The number of plants with fractionating equipment for separating the liquefied gases from heavier fractions was 202 on January 1, 1946 and 182 2 years earlier. The principal changes in number and capacity of shut-down plants were an increase in Texas and a decrease in California. Shut-down natural-gaso- line plants are usually among the smallest units in their vicinity.

Apr 1, 1947

By Walter C. Lorenz

Samples of materials containing pyrite from various coal mines and coalbeds were studied to compare their compositions and oxidizing characteristics. Pyrite was the only form of iron sulfide identified, but X-ray diffraction, emission spectrography, and microscopic analyses revealed similar suites of minerals and trace elements. The pyrite occurred usually in spherical clusters of very small crystals. The oxidation of pyrite in solutions of PeSO4 and Fe2(SO4)3 and in the presence of an iron oxidizing bacterium Ferrobacillus ferrooxidans, was studied through a manometric technique. FeS04 or Fe2(SO4)3 solutions had no appreciable influence on pyrite oxidation under the test conditions, The bacterium acted as a catalyst, greatly increasing the oxidation rates; however, in three samples that also contained calcites, bacterial oxidation was greatly reduced. The oxidation rates also increased approximately as the percentage of pyrite in the samples increased. For the series of samples studied, there was no definite correlation of the results with the location of the various mines nor with the acidity of alkalinity of the mine drainage.

Jan 1, 1963

By Paul M. Tyler

The enormous deposits of greensand in New Jersey and elsewhere in the United States, many of them close to important octant industrial centers, constitute a perpetual challenge for research chemists to convert them into a commercial asset of national importance. Following the introduction of more concentrated fertilizers, comprising synthetic mixtures of more soluble salts, the quantity of greensand used directly upon the soil has diminished, but deposits of such material still have at least potential value locally for use not only as fertilizer but also as a water softener. An annotated bibliography of the already extensive Literature on greensand, virtually complete to about the end of 1929, has been issued by the Bureau of Mines3/, and the commercial aspects as well as the technology of greensand utilization are discussed in available publications, The purpose of the present circular, therefore, is merely to provide a brief outline of certain general essential considerations for use in appraising the potential value of a greensand deposit in any given locality.

Jan 1, 1934

By Alan G. Mayton

The Bureau of Mines conducted a study to (1) determine from laboratory tests the feasibility of a photographic method for determining reflec-tances that may be applied to measuring in-mine mineral reflectances and (2) formulate a procedure for collecting and analyzing the data. The method uses a 35-mm camera with automatic flash and a gray-scale re-flectance standard to collect on film the reflectivity data in under-ground mineral mines. After the film is processed, the data on the photographic prints are analyzed in the laboratory with a photometer. Test results show the photographic method can provide values of reflec-tance to within ±5 pet of full scale (full scale = 100 pet). The method's usefulness for determining reflectivity values, within similar limits of absolute percent error at the lower end of the scale, however, has not been completely resolved by the study and consequently warrants further investigation. The method offers an acceptable means for collecting and analyzing reflectivity data for reflectivities at the higher end of the scale, i.e., 50 pet or above; it should be used with caution when reflectivity values are below 50 pet. Four films were evaluated; all gave relatively satisfactory results.

Jan 1, 1987

By G. A. Brady

Seven samples of Pennsylvania anthracite from the Bottom Ross bed were analyzed and tested to obtain data on cleaning characteristics, proximate and ultimate analyses, specific gravity, grindability, heating value, and ash softening temperature. Ash content of the samples varied irregularly from 9.0 to 34.4 percent, the range being narrowed to an upper limit of 14.8 percent ash by removing impurities dense enough to sink in a medium with a specific gravity of 1.90. Ash content of the sink material with specific gravity greater than 1.90 ranged from 56.4 to 80.4 percent; corresponding specific gravities were 2.095 to 2.534. Volatile matter contents were indicated to be higher for the ash-forming minerals than for the pure coal substance in the various specific gravity fractions of a given sample. Specific gravities of anthracites with compa¬rable ash contents but from different locations in the bed varied as much as 0.06. The grindability index increased significantly with increasing ash con¬tent of specific gravity fractions from all the samples.

Jan 1, 1968

By Nicholas Kyriazi

The Bureau of Mines has been developing breathing and metabolic simulator technology since 1970. Breathing simulation has been widely achieved throughout the world and used in the testing of open-circuit breathing apparatus, but satisfactory metabolism simulation has not been achieved. This situation required that the testing of closed-circuit breathing apparatus, which are the only type used in mines, be done using human test subjects. The goal was a machine that could accurately simulate both the breathing and the metabolic functions of a human being for testing of closed-circuit breathing apparatus. The advantages of using such a machine instead of a human being for testing respiratory protective devices lie in its ability to quantify metabolic input, its repeatability, and the lack of a need to deal with the vagaries of human subjects. This report will describe the breathing and metabolic simulators that have been developed and used by the Bureau over the past 15 yr.

Jan 1, 1986

By Lucien Eaton

This paper describing the mining practices at Mine No. 2 of the Marquette Range, Michigan is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various minim; districts of the United States. The publication, of this information should be of interest to the industry at large and the exchange of ideas thereby made possible should be of economic value to operators in all harts of the country. ACKNOWLEDGMENTS The author is indebted to the superintendent, engineer, and mining captain of the property discussed in this paper for much of the information presented. The geological classification is taken from publications of the U. S. Geological purvey.

Jan 1, 1929

By K. C. Dean

Horizontal and vertical air classification systems were tested individually and in simulated tandem use for the recovery of ferrous and nonferrous metals and of other noncombustible and combustible products from shredded urban refuse. The horizontal air system with a larger tonnage throughput was used to obtain preliminary separations, and a smaller capacity vertical system was used as a cleaning device. Air elutriation, magnetic separation, and screening of shredded minus 6-inch municipal refuse recovered 92 percent of the metal in a relatively clean iron product contaminated only by adhering coatings or entrapped materials, recovered 97 percent of the combustibles in a 97-percent combustible product, and rejected 88 percent of the nonmetal noncombustibles. Cleaning of the preliminary combustible fraction produced a 98-percent paper product while rejecting other combustibles (plastics, rubber, textiles, etc.) into a 94-percent combustible product. Retreatment of the preliminary noncombustible fraction produced a relatively clean glass product.

Jan 1, 1971

By John J. Sammarco

Computer-related accidents have caused injuries and fatalities in mining as well as other industries. Normal accident theory (NAT) explains that some accidents are inevitable because of system complexity. NAT is a classic argument in organizational sociology although it has been criticized as having imprecise definitions and lacking criteria for quantifying complexity. These limitations are addressed by a unique approach that recasts this organizational theory into an engineering-based methodology to quantify NAT complexities of computer-based systems. In this approach complexity is categorized as external or internal. External complexity is defined by the external behavior of a system, and is quantified by these dependent variables: system predictability, observability, and usability. Dependent variable data contain the perceptions of 32 subjects running simulations of a system. The system?s internal complexity is characterized by modeling system-level requirements with the software cost reduction (SCR) formal method. Model attributes are quantified using 15 graph-theoretical metrics?the independent variables. Five of 15 metrics are correlated with the dependent variables as evidenced by structure correlations exceeding 0.25, with standard errors <0.10 and a 95% confidence interval. The results also show that the system predictability, observability, and usability decreased as NAT complexities increased. This research takes a step forward in operationalizing NAT for computerized systems. The research benefits mining and other industries as well.

Jan 1, 2005

By Alvin Schallis

Of all the uses for dolomite that depend on its magnesia content, perhaps the most important is its use in basic refractories. The quantities of dolomite (including both that used as crude and that calcined before use) sold or used for refractory purposes by producers in the United States for 1920-41, inclusive, are shown in figure 1. As can be seen from the chart, the utilization of dolomite as a basic refractory is far from new; it was, in fact, the first basic refractory used extensively in open-hearth steel furnaces. After large deposits of magnesite were opened in Austria-Hungary, the use of dolomite in the open hearth declined somewhat, only to be actively revived during the World War of 1914 to 1918, when supplies from Austria were shut off. The use of dolomite as a refractory in the steel industry again declined slightly for a brief period after the Armistice, but subsequently its use has tended steadily to increase, latest statistics indicating that more dead-burned dolomite is used per ton of open-hearth steel now than during the World War of 1914 to 1918. Despite fluctuations in consumption, dolomite has continued to be by far the most widely used basic refractory material. The following table, showing the quantities of basic refractories consumed in the manufacture of steel, the principal outlet, indicates the relative importance of dolomite. The chief reason for the widespread use of dolomite as a basic refractory is its relatively low cost. Its abundance and the proximity of the deposits to the steel industry (see fig. 2) afford every incentive to enhance the desirable physical properties of dolomite refractories and to ameliorate certain of their less desirable characteristics. The present emergency, with its huge demands upon the steel industry, has lent further impetus to the work of improving dolomite refractories.

Jan 1, 1942

The objectives of this research were to examine and to laboratory performance of several brands of rigid urethane een brands, produced by 13 manufacturers, were examined. was performed in a laboratory under controlled conditions. document the foam. Eight-All testing Preliminary laboratory tests included flame spread evaluations, flame penetration, ignition temperatures, air permeability, and adhesion. Having established arbitrary cutoff values, the original 18 candidates were narrowed to 8. More specialized tests followed. The effects of water immersion and dry aging on flame spread performance and other physical properties were then examined. This Bureau of Mines report was written to provide information for those concerned with using rigid urethane foam as a sealant. Its intent is to describe the various laboratory evaluations performed and to delineate the performance of each candidate. This report neither promotes nor discourages the use of rigid urethane foams. It presents results that will enable those responsible for using or enforcing the use of rigid urethane foams in underground mines to make informed decisions.

Jan 1, 1985

By George S. Rice, J. W. Paull, R. R. Sayers

"Standard rock dust for use in the rock dusting of coal mines might be defined tentatively as powdered mineral, light colored and free of carbonaceous matter and free silica, all of which will pass a 20-mesh screen while 50% of it will pass-through a 200-mesh screen.Such dust may be prepared from limestone, gypsum, anhydrite, or shale free of sand and flint. For the initial rock dusting of the average nongaseous bituminous mines enough standard rock dust should be applied so that the combustible content of the resulting mixture of rook dust with mine dust shall not exceed 45%, a range somewhere between 35% end 45% being the practical objective sought.All entries, slopes or passageways and room necks should be rock dusted.Additional safeguards are:a.,Rockdusting roomsb.,Scattering of dust in vicinity of shots before firing.c.,Placing of barriers in the mouths of panels, cross-entries and other key positions.Redusting becomes necessary whenever the combustible content of the mine dust exceeds the permissible maximum. This should be determined by regular, systematic sampling, followed by a simple analysis of the samples for combustible content. A Bureau of Mines volumeter for measuring the density can be used for the determination of combustible content."

May 1, 1924

By Ronald D. Hill, Elmore C. Grim

The removal of overburden often exposes pyritic materials (iron disulfide). As shown in equations 1 and 2, the oxidation of this material results in the production of ferrous iron and sulfuric acid. The reaction then proceeds to form ferric hydroxide and more acid, as shown in equations 2 and 4. [ ] Consequently a low pH water is produced (pH 2-4.5). At these pH levels, the heavy metals such as iron, manganese, copper, and zinc are more soluble and enter into the solution to further pollute the water. Water of this type supports only limited water flora, such as acid-tolerant molds and algae; it will not support fish life, destroys and corrodes metal piers, culverts, barges, etc., increases the cost of water treatment for power plants and municipal water supplies, and leaves the water unacceptable for recreational uses. The amount, and rate of acid formation, and the quality of water discharged are a function of the amount and type of pyrite in the overburden and coal, time of exposure, characteristics of the overburden, and amount of available water(l). Crystalline forms of pyritic material are less subject to weathering and oxidation than amorphic forms. Since oxidation by oxygen is the primary reaction during early acid formation, the less time pyritic material is exposed to air, the less acid is formed. Thus, a positive preventative method is to cover pyritic materials as soon as possible with earth, which serves as an oxygen barrier. In terms of mining, this step is accomplished by current reclamation techniques and small open pits.

Jan 1, 1974

By R. Barany

The heats of formation at 298.15° K of calcium tungstate, calcium molybdate, and magnesium molybdate were determined by solution calorimetry. For the heats of formation from the elements, the values obtained were calcium tungstate, -402.4 ± 0.5 kcal/mole, calcium molybdate, -369.5 ± 0.3 kcal/mole, -334.8 ± 0.2 kcal/mole. For the heats of formation from the oxides J the values obtained were calcium tungstate, -49.2 ± 0.4 kcal/mole, calcium molybdate, -39.6 ± 0.1 kcal/mole, and magnesium molybdate, -12.9 [ ] 0.1 kcal/mole.

Jan 1, 1962

By Ernest W. Loya

A method for preparing gravimetric primary standards of helium in the parts per trillion range has been developed by the Bureau of Mines. The standards are used to calibrate a specially modified mass spectrometer used in determining the abundance of helium-3 and helium-4 in geochemical samples and of helium-3 in isotopically purified helium-4. The desired gas standards are prepared in 5-kg metal cylinders filled to 1,800 psia. Relative errors of less than 1 pct have been attained in the parts per trillion range using a successive dilution technique.

Jan 1, 1982

By Victor E. Kral

"INTRODUCTION The Segerstorm-Heizer property was examined by engineers 3/ of the Bureau of Mines in May and June 1942 and Mach 1943. As a result of these examination, the Nevada State Department of Highways,constructed 9.3 miles of graveled road under the mine access-road program. A magnetometer survey was made by the Geophysical Division 4/ in October 1943, and as a result the Mining Branch set up and conducted a core-drilling,project. Work on the deposit started May 24, 1944, and was suspended on July 31, 1944, but was resumed on December 4, 1944 and continued until completion on March 27, 1945.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as it, primary objective the more effective resource to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploration work, and prepares the final report. The Metallurgical Branch, R. G. Kinickerbocker, chief analyses samples and performs beneficiation tests."

Mar 1, 1947