Search Documents

By James P. Ulery, Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for pre- venting explosions during auger mining.

Jan 1, 1993

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

7. Development of Acoustic Seal Checking System The acoustic approach was shown in Section 4 of this report to be the most promising concept for checking the seals. This section describes the development of this concept into a working hardware system to be used later in the field test program. This development effort included: (1) Theoretical analysis of the acoustic behavior in the mine using acoustic modeling- techniques. (2) Experimental determination of acoustic patterns in mine passages. (3) Refinement of the theoretical model. (4) Verification of final theoretical predictions in the quarter-scale laboratory model of a mine passage and seal. (5) Development of system specifications. (6) Development of the Acoustic Prototype Seal Checking System. 7. 1 Analysis of the Acoustic Seal Checker Concept The acoustic seal checker concept is based on a model which combines corridor acoustics and hole transmission theory. The idealized model for the mine sealing application is shown schematically in Figure 66. A high intensity acoustic- source is located in a corridor at a, position adjacent to the location to be sealed. The acoustic signal transmitted through the seal is monitored by a microphone pick-up placed on the opposite side.

Jan 1, 1973

By John Jordan, Steven J. Knoll, Douglas Tesarik, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

By R. J. Matetic, D. Elsworth

The objective of this U.S. Bureau of Mines hydrologic-subsidence investigation was to evaluate the effects of longwall mining on the local ground water regime through field monitoring and numerical modeling. Field data were obtained from multiple-position borehole extensometers (MPBX's) that were used to measure subsurface displacements. Survey monuments were installed to measure mining-induced surface deformations. Numerous drawdown and recovery tests were performed to characterize hydrologic properties of the overburden strata. Coreholes were drilled above the study area to determine lithologic and strength characteristics of the overburden strata using the rock samples collected. Electronic recorders were installed on all monitoring wells to continuously monitor ground water levels in coordination with mining of the longwall panels. A combined finite element model of the deformation of overlying strata, and it's influence on ground water flow was used to define the change in local and regional water budgets. The predicted effects of the postmining ground water system determined by the model correlated well with field data collected from the field site. Without an infiltration rate added to the model, a static decrease of 3.0 m (10 ft) in water level would occur due to mining of both longwall panels and if an infiltration rate was inputted in the model, no predicted long-term effects would occur to the ground water system.

Jan 1, 1995

By R. V. Ramani, C. B. Manula, A. Owili-Eger

All the input data required to operate the ventilation simulator except the title, are entered with I10 or F1O.O formats. The title is entered with (18A4) format. The floating points are designated by (FP) and the integers by (INT)

Jan 1, 1975

By Frank E. Cash

The iron-ore ranges in the Lake Superior district are the liarquette in Michigan, Menominee and Gogebic in Michigan end Wisconsin, and the Vermilion, Mesabi, and Cuvuna in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. Accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year but closely approximate each other over a period of years. During the 4-year period 1940 to 1943, inclusive, 323,667,599 long tons of iron ore was shipped from the Lake Superior district.4/ Michigan and Wisconsin shipped 65,386,608 tons, or 20.2 percent of the total, and employed approximately 15,000 men; Minnesota shipped 258,280,991 tons, or 79.8 percent of the total, and employed approximately 10,000 men. The tons produced per man employed is much, greater in Minnesota than in Michigan and Wisconsin owing to the large open-cut production in Minnesota.

Jan 1, 1945

By Eugene T. Sheridan

This report presents data on individual plants of the fuel-briquet and packaged-fuel industries that were circularized by the Bureau of Mines, United States Department of the Interior, in its annual survey for 1958. Only plants that processed fuels of mineral origin were included; specifically, plants that manufactured briquets from charcoal were excluded. Fuel briquets and packaged fuel are manufactured by mixing fine-sized fuels with binders and compressing into small individual shapes. Both are used mainly for residential heating in the United States, but they differ considerably in appearance and physical characteristics. Briquets usually are produced as small, pillow-shaped forms, 2 to 4 inches in length, weighing from 2 to 4 ounces. Pack-aged fuel consists of 3-to 4-inch cubes, 6 or 8 of which are wrapped in heavy kraft paper to form a package weighing 10 to 15 pounds. Briquets are made with a water-insoluble binder and are designed for rough handling and outdoor storage, whereas packaged fuel generally is made with a water-soluble binder and must be stored indoors to prevent deterioration. Briquet plants are relatively large and usually are at mines or in dock areas where large quantities of fine-sized fuels accumulate. Packaged-fuel plants are smaller and are used chiefly by retail dealers to convert locally available coal and coke fines into a product that can be burned efficiently in residential beating equipment.

Jan 1, 1959

By A. J. Barry

[This is the third report related to fundamental retail roof-bolting research in underground mines (1, 2)3/ and describes an investigation of the torque-load relationship for 3/ -inch, expansion-type mine roof bolts. In a previous investigation the relationship between torque and bolt load was established for 1-inch slotted-type bolts (1). The two types of bolts differ in diameter and method of tightening and consequently may exhibit different torque-load behavior. The 1-inch bolt is tightened by turning the nut, the 3/4-inch bolt by rotating the beaded bolt itself. Experience indicates that roof bolts should be tightened to moors satisfactory anchorage sand to minimise nag of tie roof over the mine opening. The generally accepted means for determining the bolt load is to see a torque wrench to measure he torque applied in tightening the bolt and, from a predetermined relationship between torque and molt load, to, determine the corresponding bolt load. Because frictional effects may vary between one type of shell assembly or bolt and others, 7 types of expansion shell units and 3 types of 3/4-inch-diameter, mild steel bolts were tested.]

Jan 1, 1954

By Larry J. Nicks

The Bureau of Mines is investigating the catalytic activity of rare-earth compounds to develop a catalyst for the cathode reaction of a hydrogen-oxygen fuel cell. This report presents the results of studies of the catalytic activities of lanthanide oxides for the oxidation of hydrogen at 150° to 250° C. Preliminary activity tests were made with approximately stoichiometric mixtures of hydrogen and oxygen diluted with helium. A series of tests was also run under oxygen-rich conditions in which specific rate constants and activation energies were determined. Variations in rate constants up to 2,000 times were observed for the various lanthanide oxides. The three most active catalysts were oxides of Ce, Pr, and Eu, having specific activities of 6.93 X 10-7, 4.88 X 10-7, and 4.06 X 10-7 moles H2.sec-1.m-2, respectively, at 200° C.

Jan 1, 1973

By D. S. Harper, C. O. Carman

A German coal planer was put in operation in the Keystone mine of the Eastern Associated Coal Corp. , Keystone , W. Va . , in August 1960 . At present , the planer is mining in the fourth panel . The blocks of coal mined were 340 by 1,900 feet in panel 1 , 340 by 1,660 feet in panel 2 , 590 by 1,900 feet in panel 3 , and panel 4 , currently being mined , is 590 by 1,900 feet . Almost one- half million tons of coal have been mined from these four panels . An 11 - man crew handles the complete planer operation and produces an average of 500 tons of clean coal per shift . Self - advancing hydraulic props are used to support the roof over the entire face . Roof control and action on all of the panels has been highly satisfactory . During periods of extreme pressure , some additional support is required in the tail entry where evidence of weight from the retreating longwall extends about 200 feet outby the face . The time lost from production by moving equipment between panels has been reduced steadily . The move from panel 3 to panel 4 required 5 days , but it is believed that even that time could be reduced .

Jan 1, 1963

It is suggested in chapter 1 that emergency activities (including escape) are not individualistic. They tend to be group responses. If escapes from mine fires are group activities, then preparation for such events must take group behavior into account. This chapter explores the hypothesis that the miners who escaped from the three mines under study did so as members of groups. For development of this chapter, the database was examined for evidence of the existence of escape groups and for instances when individualistic behavior was paramount. Illustrations of group and/or individualistic behavior were analyzed and representative examples are provided in the following discussion. The nature of groups was discussed in chapter 3 and the following working definition was offered: "We mean by a group a number of persons who communicate with one another often over a span of time, and who are few enough so that each person is able to communicate with all the others, not at second-hand, through other people, but face-to-face" [Homans 1950]. To determine whether or not groups existed during the fire evacuations, it is important that the concept of group be clearly defined. Therefore, the discussion started in chapter 3 will be elaborated here. The defining characteristics of group given in chapter 3 were taken from Homans [1950]. They include size, person-to-person com¬munication, feelings that members have for each other, explicit and implicit rules for behavior, and common activities. An additional characteristic that is sometimes used to define groups is cohesiveness. Kiesler and Kiesler [1970] state, "Cohesiveness would include not only the attraction that the group holds for its members but also any other force operating on the individual to stay in the group." Variables said to contribute to cohesiveness include "(1) the attractiveness of a group for its members," and "(2) the coordination of the efforts of the members" [Keisler 1970]. One source of the attraction to a group occurs when "the goals or exterior tasks confronting the group are consistent with those of the individual person, and can best be handled by group action" [Cartwright and Zander 1968, in Davis 1969]. In other words, a common goal and a coordinated effort mounted to achieve that goal contributes toward the creation of a cohesive group. As discussed in the earlier review of research (chapter 1), groups have frequently been studied in laboratory or simulation settings. These methods allowed control over variables of interest. Kiesler and Kiesler [1970] state, however, that they "find group variables conceptually imprecise and experimentally difficult to work with." Experimental control, in other words, is difficult to achieve in the study of groups. The richness of the naturalistic mine fire data may provide an opportunity for an examination of groups that cannot be found in laboratories or simulations because this environment was not

Jan 1, 2000

By R. H. Fernald

In investigating general problems that relate to the fuel resources of this country, and in testing fuels belonging to or for the use of the Government, the Bureau of Mines has given considerable attention to the efficiency and economic value of producer-gas power plants. Government inquiries during the past eight years not only have shown a very low fuel consumption per horsepower-hour for these plants but have demonstrated conclusively the possibility of utilizing commer- cially low grades of bituminous coal, lignite, and peat in plants prop- erly designed for the use of these fuels. The anthracite plant has been recognized as a commercial possibility for several years, although the cost of the fuel used has in general restricted these plants to com- paratively small units. The commercial development of the producer-gas power plant in the United States has been largely within the past six or eight years. In 1909 the United States Geological Survey published in a bulletin entitled "Recent Development of the Producer-Gas Power Plant in the United States" a list of producer-gas power-plant installations. The data presented in that bulletin showed a strong development in this field and led to much conjecture as to the future of this type of power. Owing to the extensive introduction of the steam turbine, however, many persons predicted the almost immediate doom of the producer-gas plant. In addition to the inroads made by this formida- ble rival, the interest of the gas-engine enthusiasts became centered to such an extent in the oil engine that the gas producer was relegated to second place by many and absolutely abandoned by some. During the past three years the belief of many who were formerly firm be- lievers in the gas producer has been that this type of power has reached its height of development in this country and that from a commercial standpoint it can no longer be regarded as a complete success. This feeling of commercial decadence has become so general

Jan 1, 1913

By Raymond M. Kacmar

This paper describes the Bureau of Mines research program on the reliability of computerized mine-monitoring systems. The basic concepts of computerized monitoring are introduced along with its advantages and limitations. Current Bureau projects covering mine-monitoring systems are described, and some of the major areas of concern that should be addressed by future projects are outlined.

Jan 1, 1982

By Andrew J. Fergus

A study of the flotation characteristics of columbium-tantalum minerals was made by contact-angle and microflotation methods, and the findings were confirmed by flotation of two natural ores. In the contact-angle study conditions for collection of columbite, pyrochlore, and tantalite were determined for (1) sodium oleate with a sulfonate; (2) sodium isooctyl phosphate; (3) a short-chain primary amine; (4) a long-chain primary amine; and (5) a quaternary amine. These conditions were confirmed in microflotation tests. Information about collector action on common gangue minerals was also obtained by these two methods. In batch flotation tests on a pyrochlore ore and a columbite ore, it was demonstrated that collectors selected on the basis of contact-angle and micro-flotation studies would float columbium minerals from a complex natural ore. However, multiple cleaner and scavenger flotation steps will be necessary to produce commercial concentrates. From a pyrochlore ore containing 0.54 percent Cb2O5, a 44.4 percent Cb2O5 concentrate was made containing 36.4 percent of the total Cb2O5. For a columbite are the corresponding values were: 4.35, 54.6, and 67.1 percent. During the batch flotation study, wetting agents were found to aid in the gangue-ore mineral separations.

Jan 1, 1968

By R. V. Ramani, P. M. T. White, D. Sutton

4.1 Introduction Using methods outlined in previous sections of this report, programs were written and/or obtained to: i) select best combinations of "a" and "k" for up to 8 different value parameters, ii) calculate available and unavailable ore tonnages and other statistics, and iii) produce contour maps of various parameter characteristics and available tonnages on a line printer. All the above programs are written in Fortran IV for execu¬tion on IBM 360/370 computers. 4.2 Calculation of Coal Reserves The Ore Reserve program suite consists of the following sections: (a) UNIT 1: This unit is a subroutine called by Unit 2 to determine values for "a" and "k" from the given data. (b) UNIT 2: These programs calculate ore reserves and are composed of a main program and several sub¬routines. In the following, their functions are abbreviated: i) MAIN - calls subroutines, reads run parameter variables, reads borehole data and interpolates grid node values for the area of investigation

Jan 1, 1974

By F. R. McDonald

This report presents a discussion of the spectra of 39 condensed thiophenes in which the structure includes at least 1 benzene ring. The vibrational bands present in three regions of the infrared spectra of these thiophenes were interpreted by comparing the similarities of the spectra of condensed thiophenes with the spectra of substituted benzenes. In the overtone-combination region 23 of the 39 condensed thiophenes had spectra which contained sufficient detail to be usable for correlating this region of the spectrum with the appropriate benzene spectrum. In the in-plane deformation region it was possible to make correlations for the vibrations of 18 of the 39 condensed thiophenes whose infrared spectra were studied. In the out-of-plane deformation region the C-H out-of-plane vibrations for hydrogen on benzene rings in the condensed thiophenes can be correlated using known data from substituted benzenes.

Jan 1, 1967

Roof bolting is a slow, expensive, and absolutely necessary mining activity. Roof-bolting activities also account for the largest percentage of lost-time injuries in underground coal mines. Dull bits result in the application of excessive force, which bends drill steel; and changing starter and finisher steel was the most significant source of injuries associated with roof bolting. The tungsten carbide (WC) roof-bolt drill bits currently used in American, Canadian, and Australian coal mines are capable of drilling only one or two 4-ft holes and then they are resharpened once or twice to drill another one or two holes. Often, in medium-hard rock formations (sandstone), as many as 20 to 30 bits may be required to drill a single 4-ft hole. Objective To compare the performance, longevity, and cost of newly developed polycrystalline diamond compact (PDC) roof-bolt drill bits against WC bits. Research and Background Diamonds for industrial use have been scarce throughout history and continuous attempts have been made to produce synthetic diamonds. The first synthetic diamonds were manufactured in 1953. Economically produced synthetic diamonds are 1 to 10 µm in size, but in this size range, they are totally unsuitable for industrial applications. In 1972, General Electric Co. developed a process to sinter the artificially developed, minuscule diamond particles into usable products. In this process, several layers of diamond-particles-and cobalt mixture are overlaid on WC substrates and sintered at 2,350° F and 1,000,000 psi. The final product is known as PDC. Today, PDC's are available in many shapes, but their size is limited to 3/4 in, or less, in length or diameter, because pressures greater than 1,000,000 psi are required to manufacture larger PDC's. At present, diamond and PDC arc the hardest and strongest commercial materials available for wear surfaces. The PDC used in this study had a hardness 3.61 times greater than that of WC.

Jan 1, 1992

By H. H. Schrenk

Much has been written and said concerning tables of permissible or maximum allowable concentrations of various toxic substances in air, but not enough attention has been given to their limitations and how to use them intelligently . There is a tendency to place too much reliance on figures , with little or no consideration of their real meaning . The repeated publication of a figure often adds significance to it far beyond that intended by the original author or publisher . How are these figures referred to as "maximum allowable concentrations " established? What is their real meaning? To answer these questions it is necessary first to define maximum allowable concentration . The usual definition is somewhat as follows : "The average concentration to which an industrial worker can be exposed for 8- hours daily for an indefinite period without injury or occupational disease . This definition is made up of the following items : ( 1 ) Average concentration, ( 2 ) 8 - hour day , ( 3 ) indefinite exposure period , and ( 4 ) lack of injury or occupational disease . There is some controversy regarding item ( 1 ) , items ( 2 ) and ( 3 ) are usually though not invariably accepted , and there is definite disagreement regarding the interpretation of item ( 4 ) . . To reach a more satisfactory interpretation of maximum allowable concentration , attention is directed to ( 1 ) the development of tables of maximum allowable concentrations , ( 2 ) criteria on which limits are based , and (3 ) methods used to obtain data on which limits are based .

May 1, 1948

By R. E. Lindstrom

Separation efficiency of a 4 percent divinylbenzene (DVB) resin is not altered over a wide range in temperature. A 12 percent DVB resin, however, exhibits a marked sensitivity to temperature. When flow rates are high at ordinary temperatures, 4 percent DVB resin exhibits higher efficiency, but at 200° F. both resins are equal in performance. Effective separation of rare-earth mixtures may be obtained with hydrogen as a retaining ion by maintaining column temperatures above the solubility of ethylenediaminetetraacetic acid (EDTA) in the free acid form. Slightly lower separation characteristics were obtained with this method as compared with copper as a retaining ion, Recovery of 99 percent of the EDTA from spent eluting solutions that contain copper has been accomplished by a calcium-copper displacement reaction followed by EDTA precipitation. Impurities in the product are correspondingly low. Recoveries of EDTA from holmium solutions with sulfuric acid are substantial; however, those from yttrium solutions are quite modest. Radiotracer experiments show the presence of approximately 0.1 percent yttrium contamina¬tion in the recovered material. The study presented is one phase of a broad research program designed to assist the technology of separating and purifying rare-earth elements.

Jan 1, 1961

By Laurance L. Oden

The Bureau of Mines conducted corrosion tests of 18 commercial alloys in H3 P04 -phosphate rock or A1,03 slurry, in 10 pct HF, and in 25 pct H2 SiF6 to simulate three environments anticipated in a Bureau process to extract fluoride values from phosphate rock. Small alloy coupons were rotated in duplicate tests at 4.4 to 21 fps in the slurry at 170° C to determine rates of erosion-corrosion. At 4.4 fps the lowest rates, in mils penetration per year (mpy), were measured for Hastelloy C-276 (<20), Hastelloy B (30), and Inconel 625 (150);the rates increased at 21 fps to 55 mpy, 45 mpy, and 1,000 mpy, respectively. The corrosion rate for all alloys exceeded 40 mpy in either the equilibrium vapor or liquid phases of aqueous solutions containing 10 pct HF or 25 pct H2SiF6 at 100° C. Uniform corrosion in 10 pct HF at 50° C was observed only for Inconel 625 (22 mpy), Hastelloy C-276 (43 mpy), and Illium 98 (17 mpy). Inconel 625 (0.75 mpy), Hastelloy C-276 (1.3 mpy), Illium 98 (1.7 mpy), and Incoloy 825 (0.45 mpy) were attacked uniformly in 25 pct H2SiF6 at 50° C.

Jan 1, 1974