Search Documents

By R. R. Backer

The Bureau of Mines, in cooperation with Washington Irrigation and Development Co. (WIDCO), evaluated the dewatering of fine coal-refuse slurry using chemicals and various types and combinations of drains in natural earth impoundments. About 40 lb of lime and 2 lb of polymer per ton of dry solids were mixed with the underflow from the preparation-plant thickener. Clear, free water was immediately liberated from the slurry. The percent solids by weight of the slurry increased from about 17 to 30 immediately, and after 5 days increased to 45 wt-pct. This indicates a threefold reduction in total volume after 5 days from 172 cu ft/ton solids originally to 56 cu ft/ton solids.

Jan 1, 1981

By Dean E. Bluman

The Bureau of Mines investigated the convective heat transfer coefficients for recirculated suspensions of 30-micron glass beads in inert gas. Coefficients for the suspensions were not significantly higher than coefficients for the pure gas. Reynolds numbers of the suspensions were 20,000 to 35,000; solids loadings ranged from 0.0 to 0.7 pound per pound of gas. Comparison of the results with published data showed the direction of heat flow to have no effect at the test conditions.

Jan 1, 1967

By W. H. Herschel, E. W. Dean

"IntroductoryThe common practice of the petroleum industry is to measure viscosity by the use of instruments of the efflux or capillary tube type. The Saybolt universal viscosimeter has been tentatively adopted as a standard by the American Society for Testing Materials and is used extensively in the United States.Several instruments of foreign origin are also more or less familiar, such as the Redwood, the Engier, and the Baroey.Effina-type viscosimeters are well adapted to the ordinary needs of petroleum testing laberatories as they are simple and rugged in construction and away to manipulate, even in the hands of operators lacking scientific training. They have, however, certain limitations and for certain spacial types of work there are notable advantages incident to the use of the so-called torsion types of type of viacosimeter. The most satisfactory type of torsion viscosimeter now available in the market some to be that of MacMchael, which has been discussed in detail in a recent paper (Herschel, W. H., The MacMichael Torsional Viscosimeter. Jour. of Int. and Eng. Chem., vol. 12, 1920, pp. 282-286). The present paper indicates conditions under which this viscosimeter may be used to advantage in the petroleum laboratory, and outlines simple methods of operation and calibration."

Jan 1, 1921

By D. Bienstock

The Fischer-Tropsch synthesis is practicable in a reactor where the exothermic heat of reaction is removed by circulating large quantities of recycle gas through a catalyst bed of high-voids content. At an hourly space velocity of 1100, the feed gas, a mixture of 1.5 parts hydrogen to 1 of carbon monoxide, was converted 90 percent, producing hydrocarbons predominantly in the gasoline range. At these conditions a recycle-to-fresh gas ratio of 40:1 was enough to give excellent temperature control with a pressure drop of 1.5 p.s.i. per foot of bed using a steel catalyst in the form of lathe turnings. Steel parallel plates, although offering lower resistance to gasflow, were less reactive and less durable. INTRODUCTION The Federal Bureau of Mines has been engaged in a research and development program since 1944 on the synthesis of gasoline from coal. Gasification of coal with steam and oxygen to yield a synthesis gas--a mixture of carbon monoxide and hydrogen--is being investigated at Morgantown, W. Va.; and the synthesis of gasoline by catalytically reacting the carbon monoxide and hydrogen over iron by the Fischer-Tropsch reaction is being investigated at Bruceton, Pa.

Jan 1, 1960

By Tony Keller, Setsuo Maeda

Hand-Arm Vibration Syndrome (HAVS) was identified as early as 1918 in Bedford, Indiana in the U.S. Since then much research work has been done around the world in the areas of medical, epidemiological, engineering and legal aspects of HAVS. In Japan, much of the pioneering work in this field has been performed by Dr. Setsuo Maeda and his staff at the National Institute of Industrial Health (NIIH) in Kawasaki. Most recently, reports of work done by this group and by Dr. Ren Dong1 of NIOSH in the U.S., as well as many other suppliers and Japanese practitioners were presented at the 13th Japan Group Meeting on Human Response to Vibration held in Osaka2 during August 3-5, 2005. [ ]

Jan 6, 2006

By S. P. Sandoval

Several researchers have shown that the surface of chalcopyrite becomes hydrophobic under oxidizing conditions. Because dissolution of copper from chalcopyrite in dump leaching occurs under oxidizing conditions, the U.S. Bureau of Mines studied the effect of surfactants on chalcopyrite leaching under dump chemical conditions. Surfactants were selected for study because they can lower interfacial tension. The tests were conducted in shaking water baths using 250-mL Erlenmeyer flasks in statistical experimental design formats. The addition of nonionic surfactants increased copper extraction in the fernc sulfate leaching of chalcopyrite when sufficient Fe3+ was present. A positive interaction between Fe3l+ concentration and surfactant concentration was demonstrated. Copper concentration in the leachhing solutions was increased by as much as 100 pct at 25° and 50° C by adding nonionic surfactants. ionic surfactants decreased leaching. The structure of the nonionic surfactants and their hydrophile-lipophile balance (HLB) influenced surfactant performance. The branched hydrophile of an ethoxypolyol was beneficial to surfactant performance. The ethoxypolyol was the superior surfactant at 25° C, but became unstable at 50° C. Four surfactants, an ethoxyalchohol and three block copolymers, performed best at 50° C.

Jan 1, 1990

By H. J. Heinen

Malononitrile [CH2(CN)2J, which forms a carbanion in basic solutions, was investigated as a potential leachant for gold and was shown to be an effective extractant in alkaline pulps. Malononitrile was comparable to equal molar quantities of sodium cyanide (NaCN) in leaching gold from an oxide ore and yielded 10 to 20 percent higher recovery in leaching a refractory carbonaceous ore, although dissolution was slower with malononitrile than with cyanide. Complete recovery of the gold from the pregnant solutions was achieved by coprecipitation with a lead salt on zinc dust; the leachant was shown to be capable of regeneration and recycling a limited number of times. Addition of an anion-exchange resin to the carbonaceous pulp containing malononitri1e increased gold recovery from 67 to 95 percent. Some malononitrile derivatives were also shown to be gold solvents.

Jan 1, 1970

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

APPENDIX G TABLE IX MINE A 1 General Total Employees 3000 Maximum No, of Men Underground/Shift 800 Shifts/Day 3 Type of Ore Copper Daily Production (TPD) 25,000 Mining Method Room and Pillar Vein Dip/Thickness l0°/l5 ft Number of Levels/Max Depth 1/0 to 1800 ft 2 Haulage, Conveyances and Travelway Main Haulage Rubber Tire/10 miles belts Man-Ways - Typical Route of Travel to most Remote Sites Rubber Tired Vehicles Hoists - Capacity/Speed/Depth Depth under construction 3 Ventilation 2,500,000 cfm - 5 surface fans 4 Compressed Air N/A cfm 10" and 12" lines 5 Incendiary Storage 2 day powder 1000 gal fuel oil 6 Communications 1 complete system - all shops, dinner areas, and feeder/breaker stations 2 partial systems 7 Escapeway- Systems Man Check System Section boss log and punch cards Alarm System Mine phones with paging system Posting of Escape Route Maps No Escape Signs Every intersection, fluorescent paint Evacuation Drills 2/yr/shift Refuge Chambers - 1 cinder block - No longer required

Jan 1, 1976

By Jim F. Lemons

The Bureau of Mines Minerals Availability System collected and analyzed data for 34 nonlaterite and 9 nickeliferous laterite domestic chromite deposits in order to assess their viability as sources of chromium under present technologic and economic conditions. These 43 deposits, none currently in production, contain approximately 6.3 and 22.3 million metric tons of Cr203 at the demonstrated and identified resource levels, respectively. Approximately 4.6 and 15.6 million metric tons of Cr203 are recoverable at the demonstrated and identified levels, respectively, for the 34 nonlaterite deposits. None of these resources are economically recoverable at January 1981 market prices. Production of metallurgical-grade chromite (market price $128 to $144) would require a minimum chromite market price of $237 per metric ton. Chemical-grade chromite production (market price $74 to $85) would require a chromite market price in excess of $188 per metric ton. From the 34 nonlaterite deposits, roughly 5.4 and 17.6 million metric tons of ferrochrome could be produced at the demonstrated and identified resource levels, respectively; however, a minimum market price of $770 per metric ton of ferrochrome would be required to stimulate production. The nine nickeliferous laterite deposits were not evaluated through production stages because of uncertainties in process technology and cost.

Jan 1, 1982

Establish a procedure for reliably determining cation exchange parameters at an in situ mining site. The Problem Predicting the movement rates of pollutants from waste disposal sites requires reliable measurements of cation exchange parameters since cation exchange can retard pollutant movement. Reliable measurements of these parameters are also required for predicting the length of time needed to restore groundwater quality after in situ mining. Cation exchange is otten the controlling mechanism for the replacement of leach solution cations by the cations in the returning ground-water. Unfortunately, laboratory measurements using core samples are of minimal reliability. The uneven clay distribution at most sites produces a high variability in laboratory results. In addition the flow pattern in the laboratory tests is different from that in the field. Approach Bureau of Mines research has developed a field-test procedure that is quick and yields reliable and representative data. A corresponding data analysis procedure was also established in order to verify the' applicability of the computer simulation model of cation exchange used in the analysis, and of the general analysis procedure, with actual field data.

Jan 1, 1986

By Thomas H. Dubaniewicz

Fiber optic systems are being deployed in locations where explosive gas atmospheres are normally present or are present under fault conditions. The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (NIOSH, PRL) conducted a study of laser safety in potentially flammable environments. Researchers conducted experiments to estimate the mean and standard deviation of laser powers needed to ignite 6% methane-air atmospheres using single mode optical fiber tips covered by two types of iron oxide (Fe304 and (FeMn)203) mixed with a ceramic adhesive. The iron oxides, heated by a 1064 nm continuous wave laser, ignited the methane-air mixtures ,at similar powers. The minimum igniting power and maximum non-igniting power (10 tests) were 407 and 350 mW, respectively, using a 62.5 pm fiber. Laser beams guided by 125 and 80 pm diameter cladding single mode fibers produced similar methane-air igniting powers. Ignition was not observed using coal particles at powers that produced ignition with the iron oxides. Threshold ignition delays using the single mode fiber were approxinlately proportional to the inverse square of the igniting power. Ignition delays were significantly longer than the reported activation time for a comnlercial fiber optic power limiter. Comparisons are made with the results of other researchers. Published by Elsevier Ltd.

By Robert W. Gordon

This report describes the results and conclusions of the further development of a lightweight probe drill for use in anthracite mines. Improvements to the drill previously developed under Contract H0282044 were made and tested at an Eastern Pennsylvania mine. These improvements were: 1. Better hole cleaning due to the development of an air-water mist flushing system. 2. The application of roof drill bits to allow drilling through rock seams and lenses. 3. The development of a quick coupling drill system which reduced total steel change time. 4. Adaptation of a swivel to the drill anchoring system which greatly reduced set-up time between holes. With these improvements the probe drill demonstrated its ability to drill the required 11 holes in one shift. It also gained miner acceptance as a viable underground working tool. The probe drill proved to meet all of the design requirements of portability, low weight drilling controllability, structural integrity and reliability. In addition to its ability to drill the required probe pattern, the probe drill has the capability of drilling long holes. By drilling several holes over 80 feet deep the probe drill has demonstrated a potential for use in robbing pillars and for methane drainage.

Jan 1, 1981

By Jr. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel.

Jan 1, 1931

By C. H. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is al¬ways the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxida¬tion practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel.

Jan 1, 1931

By John Nagy, Henry G. Dorsett, Murray Jacobson

Laboratory studies show that ignition of a dispersed combustible dust in an open vessel may be prevented by adequate inerting . Factors affecting the inerting requirements are -- dust concentration , spark energy , ignition temperature , composition of the substances used for inerting , fineness of dust and type of combustible . The oxygen concentration of the atmosphere and in some instances the proportion of admixed inert powder and moisture required to prevent ignition are given for 367 dust samples . Variations in inerting requirements with strength of igniting source are discussed .

Jan 1, 1964

By Cecil E. Lester

Since the advent of coal mining, the minimal lighting in the under¬ground working place has been an obstacle to the safe and efficient performance of the miner's many tasks. Compounding this problem is the fact that the machines being operated in the working place are so large that the vertical and horizontal clearances around the machinery are severely limited. Consequently, in these poorly lighted and congested working places, the machine operator is unable to utilize his peripheral vision. He cannot see hazards as they develop and, too often, cannot react in time to avoid serious injury or death to himself or his fellow miners. The greatest hazard to miners inby the last open crosscut is from falls of roof which are often preceded by warning signs such as falling rock fragments, roof supports taking weight, or a sudden reduction in the height of the working place. These warning signs often go undectected because the machine operator's attention is focused on the small circle of light emitted from his cap lamp. Congress recognized the illumination deficiencies, and, in the Federal Coal Mine Health and Safety Act of 1969, charged the Secretary of the Interior with the authority and responsibility for development and promulgation of minimum standards for illuminating working places in coal mines. These standards have been developed and, as stated in the April 1, 1976 Notice, Federal Register, Volume 41, No. 64, will be promulgated on October 1, 1976, as mandatory regulations under Section 75.1719, Title 30, Code of Federal Regulations. The regulations require that the designated surfaces within the miner's normal field of vision be illuminated to 0.06 foot-lamberts while self¬propelled mining equipment is being operated in the working places. The term "working place" is defined in the Act as "the area of a coal mine inby the last open crosscut".

Jan 1, 1976

A Helix Pressure Gauge to Indicate roof bolt loads was designed, fabricated and field tested. The gauge indicated loads between 3,000 and 15,000 pounds with a ± ten per cent error. The coat of fabrication of the gauge was estimated to be $3.39 including an assumed overhead and profit per indicator for a series production of 5,000 unite. The unit can be read on a bolt to within ± 1,000 pounds load from a distance of twenty feet.

Jan 1, 1974

By Thomas V. Falkie, R. Venkataramani

Table

Jan 1, 1972

Mining and reclamation procedures that meet the requirements of SMCRA are illustrated on pages 8 and 9 for each of the three major surface coal mining methods -- area mining, contour mining, and mountaintop removal mining. The three methods involve the same basic steps: clearing the land of trees and other vegetation, removing topsoil and overburden, mining the coal, and reclaiming the land. Although all three methods would not usually occur on any single site, the illustration facilitates comparison of mining and reclamation methods and aids basic understanding of the reclamation processes that take place under SMCRA. Area Mining The area mining method is commonly used to mine coal in the flat to moderately rolling terrain found principally in the western and midwestern states. After the overburden is excavated down to a coal seam, the mining area is enlarged horizontally to expose more coal for removal. In the West, where coal seams are commonly 10 to 20 feet thick (and range up to 100 feet thick in the Powder River Basin of Wyoming), the life of some mines maybe more than 50 years. In the Midwest, coal seams are typically 3 to 7 feet thick and 75 to 100 feet below the surface. Because of the large expanse of area mines and their relatively unrestricted sites, enormous equipment is used to remove overburden and reconstruct the land. The area mining operation in the illustration is on land that was formerly used for farming. The drawing shows that the agricultural use is being reestablished immediately following reclamation. Mining is proceeding across the land toward the left side of the site. The initial excavation was made far enough away from the stream along the right edge of the site to prevent damage to the water supply. The coal under most of the site has been removed, and reclamation has been completed on some of the land. For example, some of the cattle in the foreground and those in the feedlot behind the silo are grazing on reclaimed land that has been mined. At the far left of the illustration, topsoil from the unmined area is being removed by scrapers, transported across the area of active mining, and immediately spread on the land on the right, which is being reclaimed. (Reclamation of mined land as soon as practical, as required by the Act, is called contemporaneous reclamation.) A

Jan 1, 1992

By T. A. Lang

The objective was to develop a Program Plan of analytical studies and tests for determining (1) the optimum installation tension of a coal mine roof bolt, (2) the most valid bolt support theory or theories, and (3) the most valid roof failure theory or theories. On this basis a comprehensive literature search was made and significant material dealing with coal mine roof behavior, roof bolting and roof support was collected, reviewed, classified and analyzed. Emphasis was given to the influence of rock reinforcement on the control of deformation, stress field modification and mine roof stability. An assessment was made of the effect of various parameters including bolt tension, bolt pattern and time of installation, on the effectiveness of rock reinforcement systems, and equations developed for bolt tension as a function of these parameters, and rock properties. From these studies, a major program plan of tests and studies was developed for verifying and validating the most tenable theories of roof behavior and roof support and for determining optimum bolt installation tension.

Jan 1, 1979