Search Documents

By H. O. Poppleton, F. E. Block

This investigation was made to develop a method of preparing high - purity thorium metal in quantities up to 20 kilograms per batch . Several methods for the preparation , purification , and reduction of thorium tetrachloride are discussed . Thorium tetrachloride was prepared by chlorination of decomposed thorium nitrate or oxalate with carbon tetrachloride or phosgene . tion of the crude tetrachloride was achieved by multiple distillations or by filtration of the molten chloride . It was found that high - purity thorium metal could be prepared by sodium reduction of thorium tetrachloride if chloride of sufficient purity were available . Byproduct salts and excess reductant were removed by vacuum distillation , and the resultant thorium metal sponge was consolidated by consumable - electrode or fixed - electrode arc melting . It was demonstrated that metal prepared by this method could be fabricated into bar , rod , or sheet , at room temperature .

Jan 1, 1964

By Richard D. Graves

Pitch from low-temperature carbonization of bituminous coal was hydrogenated at cracking conditions in a continuous bench-scale unit to produce low-molecular-weight oils and tar acids. The pitch contained 15.6 pct benzene-insoluble material, 4.0 pct hexane-soluble oil, and 80.4 pct asphaltene by weight. At 475° C, 7,500 psig, and 1.5 hours residence time, hydrogenation products, based on the weight of pitch, were about 36 pct oil boiling below 325° C, 24 pct hexane-soluble heavy oil, 17 pct asphaltene, 1 pct benzene insolubles, and 12 pct hydrocarbon gases. The yield of tar acids boiling below 250° C was 4.3 pct, and the yields of C6 to C8 paraffins, naphthenes, and aromatics were each less than 1.0 pct. The yield of tar acids was within the range of yields obtained by hydrogenation or high-temperature carbonization of bituminous coal (2 to 5 wt pct). Yields of oil boiling below 325° C increased with increased residence time or temperature. There was little or no effect of residence time on yields of alkali- soluble material which contained tar acids. Yields of hydro-carbon gases increased markedly with an increase in temperature from 475° to 500° C. Lowering the hydrogen pressure to 4,500 psig resulted in yields similar to those obtained at 7,500 psig.

Jan 1, 1962

By L. L. Oden

The Bureau of Mines has studied a number of processes to remove Cu from molten steel scrap with the objective of determining if any of the laboratory methods studied warranted in depth research investigations. Experimental approaches included oxidizing Cu from steel containing other metals that form stable mixed oxides with Cu (AI, Cr, Fe, Mn, Mo, and V), injecting the same metals as oxides to simplify the mechanism of complex oxide formation, partitioning Cu into alkali or alkaline earth silicate slags or oxide-moderated sulfides, and coremoving Cu and S by injecting active compounds of Ca and Mg. The most promising tests, producing nearly 0.3 pct Cu in the slag, used Ar injection of K20-moderated Na2S-FeS below the surface of molten steel containing about 0.6 pct Cu and protected by a CaO-SiOz slag; however, in depth research investigations currently are not felt to be warranted.

Jan 1, 1987

By W. P. Yant

A previous report of the Bureau of Mines dealt with the toxicity of dichlorodifluoromethane, a new refrigerant that has a remarkably low toxicity. Continued research by the Frigidaire Corporation and toxicological experiments performed in the Laboratory of Applied Physiology of the University of Cincinnati revealed another organic fluoride, dichlorotetrafluoroethane, whose toxicity also appeared to be of a very low order and whose physical and chemical properties make it suitable for refrigeration purposes. In addition to low toxicity, safety in its use is further enhanced by its physical properties, which permit the design of equipment that operates at comparatively low pressures and hence mitigates the dangers and problems of leakage. The investigation described in this report was performed by the Bureau of Mines at the request and with the cooperation of the Frigidaire Corporation.

Jan 1, 1932

By M. R. Yenchek

The U.S. Bureau of Mines has determined a method for calculating coal mine portable power cable thermal life for a specified temperature loading. This work was the culmination of a multifaceted research project involving (1) accelerated life tests of insulation and jacket materials and (2) steady-state and cyclical loading of cables. Composite Arrhenius curves were derived for common insulation and jacket materials to identify the key cable quality that precipitates thermal failure. Plots of temperature rise versus current for popular cable sizes were then referenced to develop a correspondence between cable life, based upon thermal degradation and current loading. Predictions of cable thermal life were made through integration over variable load cycles and, consequently variable operating temperatures. This procedure may have utility for both the U.S. Mine Safety and Health Administration and mining machine designers in determining the appropriate cable size for new equipment.

Jan 1, 1991

By Douglas A. Elkins

The unique characteristics of plasmas, their current applications, and ongoing research into new applications are described. Major technical and economic problems in application of plasma technology are discussed. Examples of potential applications of plasma in extractive metallurgy are described and evaluated. The report includes a selected bibliography of articles on plasma and related high-temperature technology.

Jan 1, 1969

By Bernard Lewis

The ignition problem: for a layer of firedamp bordering on a cloud of detonation products is evidently considerably more complicated than in the usual laboratory ignition experiments, in which a well-defined volume of gas is heated and the occurrence of ignition is observed after an induction period. An atmosphere of firedamp exposed to the detonation of a high explosive is subjected to heating by shock-wave compression and thermal conduction and to intermixing at the interface of the firedamp atmosphere and the cloud of deto¬nation products. Although a reliable physical-chemical analysis of the problem is not yet possible, one may nevertheless form a general view of the role of compression waves and the processes of heat transfer and diffusion at the interface. Near the mouth of a shot hole, or near a freely suspended cartridge, the firedamp atmosphere attains very high temperatures by adiabatic compression, and it is certain that such temperatures are sufficient to initiate chemical reaction. The pressure wave pattern is reproducible from one test charge to another if the initial experimental conditions are held constant; on the other hand, experiments on firedamp ignition do not yield a reproducible threshold condition for ignition, but only an ignition probability. Thus, the induction periods are sufficiently long that there is time for the compressed', heated gas layers to undergo random changes that may quench or promote ignition. Therefore, the analysis of the ignition problem hinges primarily on the discovery of the random events that modify the chemical reaction in the activated gas layers.

Jan 1, 1948

By G. R. Hopkins

According to reports received by the United States Bureau of Mines, Department of Commerce, as of January 1, 1929, there were 2,205 cracking units completed or being built in the United States, with a total daily charging capacity of 1,476,874 barrels. A similar survey of a year ago showed 2,334 units of 1,288,000 barrels total capacity. This indicates that despite a decrease in. number of units, there was a material increase in capacity. The year 1928 was, in general, an important one for the cracking branch of the industry. Gasoline consumption reached record levels, prices were higher than in 1927, and it is probable that in the late months of the year the cracking plants were operating very close to capacity.

Jan 1, 1929

By John Hays Hammond, James Douglas, J. PARKE CHAN- NING, W. R. Ingalls, J. R. Finlay

The committee making this report, consisting of Walter Renton Ingalls (chairman), J. Parke Channing, James Douglas, James R. Finlay, and John Hays Hammond, was originally appointed at a meeting of the American Mining Congress at Denver, Colo., in No- vember, 1906. The object of this appointment was the drafting of a modern law governing quarrying and metalliferous mining which could be recommended to the several States for adoption, in the hope that the passage of such a uniform law by the mining States would tend to lower the number of fatal and serious accidents. The first step of the committee (the personnel of which has re- mained unchanged from the beginning) was to procure copies of existing laws from the officials of the several States of the Union. With the assistance of the Engineering and Mining Journal, copies of the laws of Great Britain, the Transvaal, New South Wales, Victoria, Queensland, Western Australia, Tasmania, New Zealand, and certain European countries were also obtained. The replies to the inquiries made at that time developed the fact that a number of States in which mining was carried on had no laws at all. Other States were found to have elaborate provisions regulating coal min- ing, but none applying to metalliferous mining. Still other States were found to have miscellaneous and unrelated provisions passed at odd times, seemingly as the result of the occurrence of some dis- aster or other.

Jan 1, 1915

By F. S. Crawford

Interesting data on electric blasting and sinking of the Montreal No. 5 shaft of the Montreal Mining Co., Montreal, Wis., were obtained during the sinking of the last 877 feet of this shaft. Several unusual features and safety practices are also to be found in the Montreal mine. The Montreal shaft was sunk 2,156 feet from August 16, 1921, to May 1, 1924, and 877 feet from October, 1927, to June, 1928. The first section of the shaft was supported with steel sets spaced 5 feet on centers; and instead of lagging the walls were covered with three-eighths of an inch of gunite where Greenstone was encountered, and where quartz-slate was found (from the surface to the 12th level) the walls were lagged with tamarack lath treated with carbolineum, a preservative.

Jan 1, 1929

By Harold E. Heide

The United States is the world's largest consumer of tin and depends entirely upon foreign imports for its major source of supply. Only a small quantity of tin is produced on the North America continent. The advent of the war in Europe in 1939?brought a threat to our foreign sources of supply, and the Congress took steps to forestall shortages of tin and other metals. By authority of the Strategic Minerals Act, passed by Congress in 1939, and subsequent legislation, the Bureau of' Mines ?and Geological Survey conducted investigations of domestic tin deposits. Most of the tin that has been produced in North America came from the Seward Peninsula, Alaska.

Jan 1, 1948

"The following articles were produced through funding under Generic Mineral Technology Center for Respirable Dust research. Full articles appear in the proceedings, 3rd Symposium in the Mineral Industries, published in 1991 by the Society for Mining, Metallurgy and Exploration, Inc.Personal Diesel Exhaust Aerosol SamplerV.A. Marple, K.L. Rubow, and Y. TaoParticle Technology, Mechanical Engineering Department, University of Minnesota, Minneapolis, Minnesota(Section ill. Diesel I: Diesel Particulate Measurement, pp. 73-81)Abstract. Techniques are being developed for measuring the mass concentration of respirable diesel exhaust particles found in underground coal mines. Studies have been conducted over the past five years to investigate size selective 18Dlpling techniques to measure the respirable mass concentrations of diesel exhaust and mine dust aerosol particles in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler.Three personal diesel exhaust aerosol samplers have subsequently been designed and evaluated in both laboratory and field settings. These samplers use size selective classifiers for the determination of respirable mass concentrations of mineral dust and diesel exhaust particles. Their designs are based on the premise that diesel exhaust particles are predominantly less than 0.8 µm while mineral dust is greater than 0.8 µm.One design, selected for field evaluation, consists of a 10 mm nylon respirable dust cyclone followed by a 0.8 µm cutpoint impactor and afterfilter. The cyclone removes the nonrespirable particles while the inertial impactor state, collects the mineral dust on an impaction plate and allows the diesel particles to penetrate to an afterfilter. The two sample fractions of the respirable particles ( <0.8 µ.m and >0.8 µm) are gravimetrically analyzed to determine the concentrations of the diesel and mineral dust portions in the respirable coal mine aerosol."

Mar 1, 1992

By D. J. Stoops

The object of the research described in this paper was to investigate the effect of metallurgical and surface treatments on the corrosion behavior of arc-melted reactor-grade zirconium in cupric or ferric chloride solutions. An apparatus was constructed and specimens of various metallurgical conditions and surface treatments were tested for 6 days at 35° C., with aeration. Some correlations were observed between corrosion rate and the metal&apos;s condition and treatment, Specifically, the unattacked or least attacked specimens were those that had been etched as a final treatment before testing. The most severely attacked specimens were those that had been vacuum-annealed as a final treatment before testing. The moderately attacked specimens were those neither vacuum-annealed nor etched, but having a final surface treatment which left a cold-worked surface. Attack by cupric and ferric chloride was by pit- ting with no preference for grain boundaries, The corrosion scale was cow posed predominately of very fine zirconim particles, Particles from the FeC1,-corroded specimens were more pyrophoric than those from CuCl2-corroded specimens, and appeared to have a higher surface area to volume ratio. Comparison of results to those of previous investigators showed that at certain salt concentrations the more pure, reactor-grade zirconium was quite resistant to attack while the less pure, graphite-melted zirconium was severely attacked.

Jan 1, 1962

By W. L. Dare

This information circular is one of a series, published by the Federal Bureau of Mines, on methods and costs of mining uranium ore on the Colorado Plateau. This report describes the relatively small-scale operations of the Salt Wash miner: The mining method followed, the equipment used, and the production costs. It describes 10 lease-operated mines of Union Carbide: Nuclear Co. that are typical of Salt Wash operations on the plateau. These mines lie within the Uravan mineral belt3/ and arc in the Gateway, Bull Canyon, and Uravan mining districts. (See fig. 1.) Generally the ore bodies occur as irregular, discontinuous layers of ore minerals within sandstone beds in the Salt Wash member of the Jurassic Morrison formation. The ore bodies sometimes occur as rolls, pod associat with carbonaceous trash, or tabular masses. Their size and erratic distribution preclude the use of a prearranged and uniform stoping system. The mining method is simply to follow the ore and leave open scopes behind.

Jan 1, 1959

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Bolivia has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State. SYNOPSIS OF LAW All useful substances of the mineral Kingdom belong originally to the State. The soil and subsoil are regarded as two distinct parts, the latter extending indefinitely in depth (Art. 2). The subsoil is under the dominion of the State, which may either abandon it to common use, grant it gratuitously to the owner of the soil, or alienate it, in return for an annual fee, to any individual or association that applies for it. (Art. 1-3.)

Jan 1, 1929

By D. B. McGilvra

This paper, describing the mining practices and methods at the Black Rock mine, is one of a series of similar papers on mining methods in the various mines of the United States being prepared by the Bureau of Mines. The Black Rock mine is located in the northeast corner of the Butte district, about 3 miles from the center of the town of Butte, and is owned and operated by the Butte & Superior Mining Co.

Jan 1, 1930

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1957 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1-6: Current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury experience: Tables 7-36: Current data on causes of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employ¬ment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation&apos;s coal mines. (C) Injury experience, by States: Tables 37-41: Data on injuries, injury rates, employment, causes of injuries, and severity rates. (D) Major disasters: Table 42: Data on major disasters from 1948 to 1957. A major disaster is defined as a single accident in which, or as a result of which, five persons or more are killed instantly or die at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 43-47: Data on fatalities and their causes at bituminous-coal, lignite, and anthracite mines from the earliest records through 1957.

Jan 1, 1960

By Michael G. Zabetakis, Israel Liebman, Henry E. Perlee

Flammability studies conducted to date on stratified methane - air and pentane - air mixtures in air indicate that location and extent of a flammable layer are affected by molecular diffusion , gas motion , and propagation of flame . In initially quiescent mixtures , the lower limit - of - flammability zone may be determined by assuming molecular diffusion alone governs mixing rate . The upper limit - of - flammability zone can be predicted in this manner only for stratified layers with small concentration gradients ( less than 0.2 volumepercent per inch ) ; where large concentration gradients are encountered ( for example , as much as 30 volume - percent per inch ) , the initial - mixture methane concentrations that yield flammable mixtures are larger than anticipated . Flames propagating through heterogeneous quiescent methane - air atmospheres in the direction of the concentration gradient exhibit flame speeds at any point that corresponds to the flame speed of the homogeneous gas mixture having the same gas composition as that of the point in the heterogeneous system . In flowing mixtures with large concentration gradients , the degree of mixing prior to ignition does not appear to affect the flame velocity and emitted radiation appreciably in a 6.5 - ft - diameter gallery .

Jan 1, 1964

By Christopher Van Dyke, Knox Van Dyke, Lixin Wu, Jaime Gutierrez

"I. INTRODUCTION(SILICA, THE LUNG, INFLAMMATION, AND FIBROSIS)Inhalation of respirable-size silica (0. I to 5 µm in diameter) deposits the particles in the deep spaces of the Jung where oxygen is exchanged. The resulting pattern of inflammation is substantially different compared to that observed from other inhaled substances such as carbon, polystyrene titanium dioxide etc. 1 Following the inflammatory reaction the body attempts to isolate the damage by walling off the area via fibrosis. 2 The unique nature of the inflammatory response to silica makes it logical to infer that fibrosis is a later-stage manifestation of the initial inflammatory damage. In addition to the inflammation extensive lysis and cellular death particularly to macrophages and neutrophils, can occur, depending on the dose of silica.' The ingestion of significant amounts of silica by macrophages and neutrophils produces an inflammatory sequence which activates the lipoxygenase pathway of arachidonic acid metabolism and produces platelet activating factor (PAF) and leukotrienes (LT).4·5II. CALCIUM IONOPHORE MIMICS SILICA TOXICITY IN VITROPhagocytic cells exposed to silica in vitro produce PAF and LT. This response is reminiscent of phagocytic cells exposed to the calcium ionophore (A23 l 87) in the presence of ionic calcium.6-8 A23 l 87 forms a complex with free ionic calcium which passes through cellular membranes, thus transporting calcium inside the cell. The increased intracellular calcium concentration triggers the production of small amounts of prostaglandins large amounts of LT. PAF and. depending on dose cellular death (see Figure 1 ). Could silica cause LT production and cellular death by a similar mechanism? How could silica - an inert solid - act in a similar fashion as a soluble stimulant? Clearly the negative SiO2 and OH- surface of silica can bind calcium ions9 and therefore could theoretically act as a solid-state ionophore releasing bound calcium inside of cells following phagocytosis."

Jan 1, 1998

By L. E. Schultze

As part of the Bureau of Mines research program on recovering alumina from domestic resources, methods for extracting iron from aluminum sulfate solutions (obtained by leaching kaolinitic clay with dilute sulfuric ,acid) were investigated. In countercurrent extraction experiments at a l-gal/hr flow rate of aluminum sulfate leach liquor, the iron concentration &apos;was decreased from 1.4 g/l to 0.01 g/l after four stages of using a primary amine extractant. The iron-loaded amine solution was regenerated in five stages using 3[N] sulfuric acid or in four stages using 6[N] sulfuric acid. The aluminum sulfate solution obtained was suitable for the preparation of alumina meeting cell-grade standards of less than 0.01 pct iron.

Jan 1, 1979