Search Documents

By P. F. Sands, Michael Sokaski, M. R. Geer

The purpose of this investigation was to determine the advantage of using either a conventional sieve bend ahead of a vibrating screen or of attaching a sieve - bend screen surface onto a vibrating screen to serve as a scalping deck when dewatering or draining dense medium from fine coal . In dewatering , use of either the sieve bend or scalping deck increased the capacity of the vibrating screen tenfold and the recovery of coal finer than 0.5 mm threefold , with no sacrifice in the moisture content of the oversize product . In dense -medium drainage , either the sieve bend or the scalping deck reduced the amount of magnetite retained on the product of the vibrating screen , particularly when the medium was as dense as that characteristic of the underflows from dense - medium cyclones . The sieve bend was slightly superior to the scalping deck in dewatering , but the scalping deck was clearly superior in dense -medium drainage . Additional advantages of the scalping deck are lower cost and a substantial saving in headroom.

Jan 1, 1963

By J. E. Pahlman

The Bureau of Mines performed research on a fluid-bed magnetic roasting process for nonmagnetic taconites that utilizes low-rank coals and lignites as reductants and fuels. Roasting tests on a Michigan nonmagnetic taconite were conducted at 600° to 725° C with lignite or subbituminous coal as reductants. Partial combustion of the reductant reduced the amount of heat externally applied to the reactor to maintain the desired reactor temperature. Cleaned, dried reactor top gases were recycled to recover a portion of the reducing potential in these gases without adversely affecting concentrate grade and iron recovery. Highest iron recoveries for magnetic concentrates were obtained at a roast temperature of 650° C with lignite and at a roast temperature of 725° C with subbituminous coal. Magnetic concentrates were obtained that were comparable with commercial concentrates.

Jan 1, 1976

By A. R. Taylor Jr.

The heat capacities of a-quartz form beryllium fluoride were measured at approximately 3° intervals from 8° to 300° K., using an adiabatic calorimeter. At 298.15° K the heat capacity and entropy were 12.39 cal/deg mole and 12.75 ±0.04 eu respectively. Enthalpy measurements were made with an ice calorimeter at approximately 30° intervals on the quartz and glassy forms of beryllium fluoride between 300° and 1,200° K. A melting point of 825° K and an 0,-8 type transition at 500° K with a heat effect of 75 ca1/mole were deter-mined from the enthalpy data for the quartz-type sample. Beryllium fluoride glass crystallized spontaneously into the quartz modification at 500° K. The heat of the reaction BeF2 (a-quartz) .... BeF2 (glass) was found to be 1,125 ±16 cal/mole at 298° K by solution calorimetry. This value, when corrected to 273° K, was used to correct for the heat absorbed by the formation of glassy BeF2 when the sample was dropped into the ice calorimeter from temperatures above the melting point. Using corrected enthalpy measurements, the heat of fusion was determined to be 1.13 kcal/mole at 825° K.

Jan 1, 1965

By E. C. Baker

The Bureau of Mines estimated the economic feasibility of investing in a directional hole methane drainage project in the Pittsburgh coalbed for 5 yr in advance of mining. This report estimates the capital investment and operating cost of recovering 325 MMft3 of methane gas per year and the selling price of approximately 317 MMft3 of gas per year. The labor, equipment, and supply requirements were determined from those of a previous directional hole drilled at the Emerald Mine, near Waynesburg, PA. The cost of equipment, materials, services, and labor are in third quarter 1982 dollars. They were obtained from vendors, contractors, and the U.S. Department of Labor. Findings indicate a total capital investment of $1,381,160. Annual operating cost amounted to $167,690. At a wellhead price of $2.05 per thousand cubic feet, the sale of approximately 317 MMft3 of gas per year results in a rate of return on investment of approximately 25 pet.

Jan 1, 1984

By Ani Chitaley

A new method has been developed for handling supplies in underground bituminous coal mines. A survey indicates industry wide implementation potential for the proposed method. Reduction of supply handling accidents' by as much as 73% and improvements in the productivity of face operations by at least 3% are anticipated benefits. The new method is based on the palletization of daily supplies and the use of a forklift for carrying out the handling tasks at the underground section. A prototype of the forklift has been delivered to the U.S. Bureau of Mines. The forklift has demonstrated several important features necessary for underground supply handling such as compactness, maneuverability, visibility, ease of control and auxiliary attachments for hoisting, carrying timber and pulling. Design improvements are recommended for future generation underground forklifts. These relate to higher speed, increased battery duty cycle, higher payload and modified traction/steering to eliminate plowing of soft mine floors.

Jan 1, 1983

By W. L. Anderson

Standard tellurium analytical procedures were modified to obtain the greater sensitivity needed to support a survey of tellurium resources by the Bureau of Mines. Resulting volumetric and spectrophotometric methods for determining tellurium in all types of tellurium-containing materials are described. Sample decomposition and preliminary separations of interfering selenium, gold, and silver are the same in both procedures. The volumetric method is applicable to samples containing a minimum of 10 parts per million of tellurium, In this method the tellurium is reduced to elemental form, and the colloidal suspension is titrated with 0.01 normal iodine solution. The weight of sample for analysis, from 0.25 to 10 grams, should be selected so that the sample contains 0.1 to 5 milligrams of tellurium. To insure accuracy, duplicate samples should be run and the results averaged, particularly on samples of low tellurium content: The limit of determination is 0,001 percent tellurium, which is equivalent to 0.1 milligram of tellurium when using a 10-gram sample. The spectrophotometric method is particularly applicable to low-tenor materials containing from 0.5 to 50 parts per million of tellurium. Up to 10 gram samples are required for making accurate determinations in the low-concentration range. The sample used should contain between 5 and 100 micrograms of tellurium. The turbidity of a colloidal suspension of tellurium prepared from such a sample is determined in a spectrophotometer .t at a. wave-length of 440 millimicrons, and this value is compared with those of standard samples containing known amounts of tellurium.

Jan 1, 1963

By R. P. Jewett

The object of this investigation was to correlate the crushing strength of green pellets prepared from magnetite, specular and earthy hematite with the particle size of these respective raw materials. In this study no attempt was made to correlate the strength of fired pellets and particle size. The effect of particle size upon a number of fine ores and concentrates was studied. Much of the low-grade ore reserves in the Lake Superior Region must be finely ground before concentration and then agglomerated for iron and steelmaking processes. Fine natural ores also must be agglomerated. Pellets constitute an important type of agglomerate. Considerable handling occurs during screening to remove undersize and oversize pellets, and in transfering green unfired pellets from the balling machines to the heat-hardening equipment. As a result the strength of the green pellets is a factor of great importance.

Jan 1, 1961

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to pieces weighing as much as 5 tons, a 150-ton batch retort was designed and constructed at the Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11-1/2 feel in inside diameter and is supported in a 92-Foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, is currently being used as the test shale. To date, three runs have been completed. Results of the second and third runs are reported in this paper. The two runs considered in this report are the first of a series of nine to determine operating conditions that will yield maximum oil recovery from a column of mine-run shale. Variables studied :ire the oxygen content of the retorting gas and the space velocity of the retorting gas expressed as ft3 gas/ft3 bed/min. Oil recoveries for the two runs reported are 62.2 volume percent of Fischer assay for the run using higher oxygen and space velocity, compared with 39.3 volume-percent when less oxygen and a Lower space velocity were used.

Jan 1, 1971

By D. D. Fischer

Recovery and separation of molybdenum and rhenium from a process solution was accomplished by a technique developed by the Federal Bureau of Mines involving a combined solvent extraction and activated carbon adsorption procedure. The processing sequence required treatment of the solution with S02 to reduce the chlorate ion and adjust the pR prior to solvent extraction of molybdenum and rhenium with a tertiary amine. Molybdenum and rhenium were stripped from the organic phase with an NH40H solution, and the strip solution was then passed through activated carbon to preferentially adsorb the rhenium. After washing entrained molybdenum from the column with a brine solution, rhenium was eluted with an MeOH-H20 mixture. The activated carbon was regenerated with water. Molybdenum was recovered as (NH4)6Mo7024 by evaporating the column effluent. Rhenium in the column eluate was reextracted with a tertiary amine, stripped from the organic phase with dilute NH40H, and recovered as NH4Re04 by evaporating the strip solution. The final (NR4)Re04 product contained < 80 ppm impurities. Sodium sulfate was crystallized from the first solvent-extraction raffinate by lowering the solution temperature to 0° C. Precious metals contained in the original process solution were adsorbed onto the activated carbon.

Jan 1, 1975

By M. C. Irani

The Bureau of Mines, in cooperation with the Mine Safety Appliances Co., has developed a new methane analyzer system for underground applications. Methane enters coal mine ventilation air from the breakup of coal at the active face, from the collapse of roof rock during retreat mining, and from the ribs abutting virgin coal. Each source contributes varying amounts to the total emission, depending upon rate of mining, type of mining, and the character of the coalbed and adjacent strata. The evaluation of individual parameters of methane emission requires the continuous monitoring of individual mine sections over a long period of time. The methane analyzer system was developed to meet this need. The system has been installed and operated in an active mine in the Pittsburgh coalbed. The system and details of its installation and calibration are described. Data are presented to substantiate its reliability.

Jan 1, 1975

By Lee M. Manna

Approximately 10,000, 10-Ton, 4 wheel, 2 truck, coal mine cars are in general service in U. S. Mines. None are equipped with an automatic braking system. Very few are equipped with hand or parking brakes. The report lists major manufacturers of the car and develops estimate as the percentage represented. It complies physical specification of cars of major car manufacturers, and develops a composite clearance diagram. It then discusses a pneumatic system employing truck components for an automatic system that could be used as an add-on unit. The components are listed and priced and a schematic circuit is developed for the system. Recommendations as to future programming are made.

Jan 1, 1976

By R. D. Leitch

The work of the United States Bureau of Mines on stream pollution by coal-mine drainage has included a study of seasonal variations in acidity and volume of several streams in Pennsylvania. The acidity of these streams has been determined during the two or three years prior to 1930 and the results may be considered to represent "normal" low water conditions. The summer of 1330, however, was unusually dry and represents what may be termed "extreme low water conditions on these streams. This report is a comparison of the results obtained for extreme low water of 1930 and for other years. The streams investigated were Buffalo Creek in Somerset County, Indian Creek (lower 5 miles) in Westmoreland County, Little Toby Creek in Elk and Jefferson Counties, Daguscohonda Run in Elk County and West Creek in Elk and Cameron Counties. These will be treated separately in the order given. Most of the descriptive matter and physical data pertinent to the streams and drainage basins are taken from published reports of the Pennsylvania State Water Supply Commission, 1917.

Jan 1, 1931

By J. L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former US Bureau of Mines (USBM) to engineer techniques that will reduce the hazards in the mining workplace associated with coal bumps. Recent research focused on a longwall coal mine in Utah with overburden greater than 750 m (2,500 ft) containing several massive sandstone units. The primary field instrumentation at the site was three-dimensional, full waveform, autonomous microseismic arrays placed underground and on the surface in order to surround the active multi-panel longwall district. The purpose of these arrays was to help investigate the strata mechanics associated with the redistribution of stress and the associated gob formation of the longwall. Specifically, the seismic arrays were used to determine the timing and location of the failure in the strata surrounding the active mining. Overall 13,000 seismic events were detected and located with on-site processing during the five months the panel was being mined, including a magnitude (ML) 4.2 event. Of these, a smaller subset of 5,000 well-located events was selected during post-processing to form a consistent data set for analysis in this paper. From this data set, it was observed that the seismic events generally occurred in advance of the longwall face, both above and below the panel, consistent with failure of the strata in the forward stress abutment zone. Also, the occurrence of the ML 4.2 seismic event within 150-180 m (500-600 ft) of a deep cover longwall face with no associated bump caused a re-evaluation of the nature of the connection between seismic activity and coal bumps.

Jan 1, 2002

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U. S. economy. The USBM&apos;s data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1994

By Carlton E. Brown

This report contains information on the cells or containers used to hold a known small depth (usually 1 mm. or less) of the dust-containing liquid from impinger, 5/6/ filter-paper,7/ and other samples collected from the air while the particles revealed by a microscope (equipped with a 16-mm., 0.25- or 0.50-N. A. objective and ordinarily used with axial light-field illumination) are counted in order to obtain an index of the concentration of dust in the sampled air. Information is given on such subjects as the kinds of cells available, kinds used, actual depths of cells, and construction of simple, inexpensive cells. ACKNOWLEDGMENTS The interest, encouragement, and assistance received from H. H. Schrenk, chief chemist of the Health Division, in the preparation of this report are gratefully acknowledged, as &apos;is all other assistance received.

Jan 1, 1945

By Frank J. Wiebelt

The Carbonate King zinc mine is on the west slope of Kokoweef Peak, Ivanpah Mountains, San Bernardino County, Calif. It has produced more-than 10,000 tons of ore with a 39-percent?zinc content since mining operations began in 1940. The ore, consisting principally of calamine and smithsonite, occurs in replacements of the YellowPine limestone. Milling, has been done from the surface to a depth of 275 feet. Eight holes, aggregating 2,121, feet were drilled by the Bureau of Mines in an endeavor to establish extensions of the worked-out ore bodies and to develop new ones. Although indication of mineralization was found in several of the holes, no new ore bodies were developed.

Jan 1, 1949

By Kenneth G. Broadhead

Four applications of radiotracer techniques in metallurgical research are described: (1) In electrowinning tungsten from scheelite, molybdenum 99 was used to detemine the molybdenum concentration of the fused alkali-phosphate bath and the electrowon tungsten; (2) an attempt to detemine the solubility of tagged ceric oxide in molten CeF3-BaF2-LiF was unsuccessful, but a high rate of cerium ion exchange was observed; (3) iron 59 was added to cerium during casting and used to follow the migration of iron during solid state electrolysis; (4) radiotracers were used in developing special analytical techniques applicable to high-purity rare-earth metals produced by molten salt electrolysis.

Jan 1, 1963

By W. W. Simpson

During cyanidation of mercury-bearing gold-silver ores, significant amounts of mercury are extracted. The presence of mercury decreases. gold loading and increases mercury stripping time on activated carbon, complicates fire refining of the gold cathodes, and creates a potential health hazard. Addition of calcium sulfide (CaS) to the cyanide leach slurry precipitates the solubilized mercury but also some silver. The Bureau of Mines investigated silver loss during CaS precipitation of mercury. Addition of 0.1 lb CaS per short ton ore to a mercury-bearing gold-silver ore precipitated both mercury and silver. However, if copper was added with CaS, or if the ore contained copper, much of the sil-ver loss was prevented. Addition of 235 ppm Cu with 0.1 lb/st CaS, prior to carbon-in-pulp adsorption, resulted in 89-to 97-pct, 80-to 91-pct, and O-pct adsorption of the solubilized gold, silver, and mer-cury, respectively, on the activated carbon.

Jan 1, 1986

By M. F. Chambers

The U.S. Bureau of Mines conducted experiments on electrowinning of neodymium metal by using a molten-metal cathode at 650° C and an electrolyte of 50 mol pct NdCl3 (neodymium chloride) and 50 mol pct KCI (potassium chloride). The molten-metal cathodes were alloys of magnesium and zinc or magnesium and cadmium. Current efficiencies were 90 pct with a Mg-Zn cathode and 80 pct with a Mg-Cd cathode; The Mg-Cd cathode was easily separated from the electrolyte. In contrast, the Mg-Zn cathode tended to mix with the electrolyte, making separation difficult. The cathode metals were separated from the neodymium by distillation at 1,100° C under a vacuum of 10-3 torr. Neodymium metal of 99.9+ purity was recovered from the Mg-Cd alloy cathode after 30 min distillation time. The neodymium recovered from the Mg-Zn system contained almost 2 pct Zn after vacuum distillation. Continuous operation using the Mg-Cd alloy cathode was demonstrated.

Jan 1, 2010

Viable domestic mineral industries are essential to the economic health of the United States and the well-being of its citizens. The charts in this publication reflect developments significant to the Nation&apos;s mineral industries during 1975. Last year was a year of reduced activity for the Nation&apos;s mineral industries. Although the value of the country&apos;s total mineral output rose, for example, the overall production and use of many minerals fell. At the same time, the industry experienced lower profits and higher debt/equity ratios. These and other adverse effects on many segments of the Nation&apos;s mineral industries resulted from the overall decline in domestic and international economic activity.

Jan 1, 1976