Search Documents

[ ]

Jan 1, 2011

By H. P. LeVan

Research was conducted to examine the feasibility of extracting manganese from Georgia umber ore by a three-stage continuous sulfuric acid-ferrous sulfate pickle liquor leaching process. A continuous cyclic process for treating the umber was operated successfully, using a synthetic solution simulating a ferrous sulfate fortified anolyte solution discharged from a manganese electrolytic cell as the leaching medium. Leaching efficiency based on removal of the manganese from the ore ranged from 83 to 89 percent for all systems tested.

Jan 1, 1965

By Suresh K. Bhatt, Gary L. Mowrey, Timothy R. Rehak, David K. Ingram

Coal and nonmetal mining used about 4.3 billion pounds of explosives and blasting agents during 2001 in the United States. A major part of this consumption was related to surface mining. Mine Safety and Health Administration accident data indicate that flyrock and lack of blast area security were the primary causes of blasting-related injuries in surface mining. Fatal injuries due to lack of blast area security were primarily caused by failure to clear blast area or inadequate access control to the blast area. At a coal mine, a neighbor walked into the blast area and was fatally injured. The blaster could not see the victim entering the blast area from the firing station. In another case, a passenger in a vehicle was fatally injured by flyrock because highway traffic was not monitored during the blast. In another example, a dozer operator entered a blast area due to lack of access control. Several fatalities resulted from using inadequate or no blasting shelter. A crane operator was fatally injured while standing in the open about 120 ft from the blast site. In another instance, a helper, standing about 150 ft away from the edge of a blast, was fatally injured by flyrock. In a limestone mine an equipment operator was fatally injured while guarding access roads in a pickup truck. This paper briefly describes six representative fatalities due to flyrock and lack of blast area security in coal and nonmetal mines. Several mines were visited to collect information relative to working practices aimed at mitigating blasting hazards. Salient information obtained through these visits is presented.

By Charles Vaught

The U.S. Bureau of Mines evaluated the self-contained self-rescuer (SCSR) donning proficiency of 243 miners. These workers were from eight underground coal mines in the eastern United States. The objectives of the study were (1) to gather information on skill levels, since all miners in the study had prior instruction and opportunity to practice donning the apparatus, and (2) to summarize a quality control procedure useful in conducting periodic evaluations of donning proficiency. The sampling procedure used proved to be both reasonable and efficient in gathering information on training effectiveness. It also provided a good statistical base for making informed site-specific decisions regarding SCSR training needs. Results from the observed samples at each of the eight mines indicate a wide variability across sites. The rate at which miners failed to isolate their lungs varied from 3.3 to 40.0 pet. Concomitantly, proficiency rates (miners either performing adequately or demonstrating a perfect 3 + 3 sequence) ranged from 13.3 to 63.3 pet.

Jan 1, 2010

By G. W. Jones, R. E. Kennedy

A simple , quick, and relatively accurate device is needed for determining the presence of very small concentrations of organic halide gases in various atmospheres . Such a device would enable safety engineers , health officials , and others to discover quickly the presence of these gases in a suspected atmosphere and thus be able to apply protective measures promptly. This detector should prove useful in detecting leakage of halide gases from refrigerating and air - conditioning systems and in determining the presence of halide solvents in the atmosphere of dry - cleaning and degreasing establishments where organic halide solvents are used . Virtually all poison war gases are halide compounds . Because of the high toxicity of these gases , even in very low concentrations , a detector having the proper sensitivity should be useful in civilian defense for determining when atmospheres are relatively free of poison gases .

Apr 1, 1943

By M. S. Cetiner

This report describes the prototype development If a medium to high voltage coupler, suitable for underground coal mining operations. The coupler has such unique features as automatic dust covers and continuous phase pin shielding. The coupler is rated at 7500V and 250A continuous operation.

Jan 1, 1982

By X. B. Starnes

"INTRODUCTION The Eva Tanguay property is in Crittenden County, Kentucky, about 1 mile south or the village of Mexico, and can be reached from Marion, the County seat, by travellng south on State Highway 91 for 6.8 miles and then turning southwest on State Highway 70 and traveling 2 miles farther.Although the property lies between the Huffaw and Pigmy properties, which together have produced 200,000 tons of fluorspar ore, production from the Eva Tanguay has been estimed at only 1,000 tons. Geological factors on the property indicated the likelihood of an ore occurrence, and the author examined the property in April 1944. Shortly thereafter, the U.S. Geological Survey wrote a report on the property, which was not published. A drilling program was initiated by the Bureau of Mines November 1, 1944, and continued until eight holes totaling 3,137.5 feet were drilled.The holes showed that the Tubb fault system on the Eva Tanguay property is composed of three members, all of which contained commercial ore. The line dividing the Haffaw and Tanguay properties crosses the vein outcrops, causing a part of the ore indicated to be on each property.The mineral rights, which are leased by Robert Frazer of Marion, are owned by Mrs. O. S. Denny and W. C. Bohn, both of Marion."

May 1, 1947

By F. Varley

Researchers from the National Institute for Occupational Safety and Health (NIOSH), in cooperation with mine operators, conducted a study of heat stress exposures among mine rescue workers in underground mines. Mine rescue workers face extreme heat loads as they enter hot and poorly ventilated environments, particularly when they are wearing breathing apparatuses. The burden of wearing a closed-circuit breathing apparatus (CCBA), the inability to drink fluids for extended periods of time, and the potential for ventilation disruptions and fires combine to increase the risk of heat illness during a response to an emergency. In this research, ambient environmental conditions and heat strain indicators were measured using conventional ventilation monitoring tools during mine rescue training exercises. Heat strain was measured with an ingestible temperature-sensing pill that measured core temperature continuously. In addition, a heart-rate monitoring chest strap was used to indicate physical strain resulting from physical activity and heat. Both core temperature and heart rate data were transmitted to a remote recorder worn by a rescuer and time-stamped. Team activities were also observed to determine the contribution of work rate to a person’s total heat load. The effectiveness of several engineering controls, such as cooling the air inhaled by rescuers through an apparatus, wearing cooling vests, and supplying water through the CCBA masks, were investigated. Administrative controls, such as limiting the duration of exposure and controlling the work rate through forced-rest regimens, were also evaluated. Results to date are discussed, and tools for evaluating team condition and estimating the length of time it would be safe for rescuers to work are proposed.

By P. L. Woolf

Seven evaluation tests with blast furnace iron bearing burden materials are described. The effects of pellet strength, fines in the burden, decreasing slag volume, pellet size, eliminating stone with superfluxed sinter, and eliminating stone by prefluxing the pellets were determined. Fluxed pellets and fluxed sinter made with the same ore fines were compared. The tests were conducted under cooperative agreements between the Bureau of Mines and North American steel companies. The objectives were to improve blast furnace practice, expand and develop understanding of the operation and theory, quantify the effects of changes, and explore the limitations of operability. This work was part of an extensive program of blast furnace research in experimental blast furnaces at Bruceton, PA conducted in the years 1958 to 1967.

Jan 1, 1984

1. PURPOSE The Temporary Face Support System (TFSS) consisting of beams, posts and carrying-emplacing equipment was developed to provide temporary supports between the working face and the permanent roof supports. 2. GENERAL DESCRIPTION The system consists of: ? A Beam And Post Carrier And Deployer (BAPCAD), a self-propelled machine that carries as well as emplaces the beam-and-post sets. ? Lightweight mechanically self-deploying posts designed to safely support a load of 10,000 pounds each. ? Lightweight constant strength beams (bars) capable of sustaining an approximate equally distributed load of 8500 pounds. Note. All referenced figures and drawings are found at the back of this manual.

Jan 1, 1980

By Katherine Harding

Basic concepts of matrix algebra and manipulations of matrices are presented in such a way that little competence in mathematics is required. Examples are always included to illustrate concepts and techniques. The paper is divided into six sections. The first four sections are devoted to some of the more basic concepts of matrix algebra, whereas the last two sections are concerned with specific applications.

Jan 1, 1967

By B. K. Shibler, I. S. Solet, H. W. St. Clair

"This study was undertaken to provide a more adequate knowledge of the chemistry of the sulfide volatilization process for recovery of tin from low-grade Bolivian ores. The investigation was partly supported by the Department of State under its program for scientific cooperation with South American republics.The results of this investigation demonstrate the conditions under which cassiterite (Sn02) may be converted to stannous sulfide by reaction with pyrite or sulfur vapor. Quantitative data are given on the rate of sulfidization and on the vapor pressure of stannous sulfide.INTRODUCTIONAlthough the United States is the world's largest consumer of tin, virtually no tin ores occur within our national borders. Most of the world's tin supply comes from alluvial deposits in the Far East and in Africa, The major sources of tin ores are Malaya, Indochina, Bolivia, Belgian Congo, Nigeria, Thailand, Burma, China, and the United Kingdom. Bolivia is the only important source of tin in the western hemisphere. It was the chief source of tin f or the United States during World War II. The Government-owned tin smelter at Texas City, Tex., was built primarily for smelting Bolivian ores and depends largely on Bolivian ores for its operation. Bolivia is the only major tin-producing country in which the tin ores occur as vein or lode deposits requiring underground mining. Most of the tin from the Far East and Africa is mined by dredges from alluvial or placer depos its. It is recovered as a high-grade concentrate of cassiterite relatively free from impurities. The tin minerals in the lode deposits are more intimately associated with other minerals and more difficult to separate into a clean concentrate. Furthermore, a large part of the tin in the original ore is lost during concentration. The ores as mined contain only a few percent of tin, so they must be milled to separate the gangue minerals and produce a concentrate containing 30 to 40 percent tin before they are shipped to the smelter. The losses of tin that occur during milling vary from 18 to 65 percent. The average recovery of tin from Bolivian ores is probably 50 to 60 percent."

Dec 1, 1954

By Wing G. Agnew

The drilling and bit-sharpening practice in the southwest Wisconsin zinc district generally conforms to the procedure described herein, except at very small properties, where drill steel is sharpened by hand. Though hot milling of rock-drill bits is practiced in South Africa on some of the large-scale operations, it is seldom seen at American minus in any form. Because of the simplicity and low cost of the equipment, it was thought that a brief description might prove interesting to same of the operators in ether districts who do not have enough steel to sharpen to warrant equipping an elaborate sharpening shop.

Jan 1, 1936

By W. P. Yant, R. R. Sayers

The rather sudden increase in the use of methanol as an antifreeze for automobile radiators has caused considerable comment , with some anxiety to persons interested in industrial and public health , regarding the possible health hazard in dispensing and using the product . In view of this , the chemical industry interested in the manufacture and marketing of methanol requested the Bureau of Mines to make an impartial and extensive investigation of the hazard involved . With the assistance of the industry this investigation is now in progress and will extend throughout the present winter . When these observations are finished a complete report will be made . At present , however , the acute interest in the problem and the many inquiries that have been received from manufacturers of methanol , garage owners , the automotive industry , public health officials , and private persons demands a brief statement relative to the reasons for the recent availability of methanol for antifreeze purposes , the plan of the bureau's investigation , and the trend of the results of the investigation obtained to date .

Dec 1, 1930

By Graham W. Mark

A chemical method of analysis for beryllium was developed recently in Bureau of Mines laboratories. In this method, quinalizarin (1-2-5-8 tetrahydroxyanthraquinone) in N/4 NaOH is used as a colorimetric titration reagent. This solution has a reddish-purple color, whereas the solution containing equivalent amounts of beryllium and the dye is rather blue. In the titration procedure, standard quinalizarin solution is added to the unknown beryllium sample and to two standard beryllium samples of different but known concentrations. Then adjustments in concentrations of BeO in the two known and of quinalizarin in all three are made until the red-violet shade of the unknown is halfway between that of the two knowns. The amount of BeO in the unknown is calculated from the known BeO content of the solutions between which it lies. It is extremely difficult to distinguish the slight differences in shade of these solutions without the use of a proper light filter, especially when the concentration is over 0.1 mg. of BeO, so a study was made of the transmission characteristics of quinalizarin in N/4 NaOH and of the corresponding beryllium complex to determine what filter would give the most contrast.

Jan 1, 1950

By Terry S. Cory

This report covers antenna design, analysis, and development work suited for use with a wireless radio communication system operating at medium frequency. The work includes the test and evaluation of prototype vehicular antennas developed during the program.

Jan 12, 1978

By Robert E. Barieau

In the design of plants to separate helium from natural gas, it is necessary to estimate the enthalpies of the various streams at various positions in the process. This Bureau of Mines report surveys the various methods that have been used to determine enthalpies and gives information on the organizations with such capabilities. The minimum information required for developing an enthalpy diagram is presented, and the relative merits of the various methods are discussed. It is concluded that methods that require no mass flow rate or energy measurements are to be preferred.

Jan 1, 1965

By Robert E. Barieau

In the design of plants to separate helium from natural gas, it is necessary to estimate the enthalpies of the various streams at various positions in the process. This Bureau of Mines report surveys the various methods that have been used to determine enthalpies and gives information on the organizations with such capabilities. The minimum information required for developing an enthalpy diagram is presented, and the relative merits of the various methods are discussed. It is concluded that methods that require no mass flow rate or energy measurements are to be preferred.

Jan 1, 1965

By F. S. Wartman

Recent changes in metallurgical practice, particularly those in flotation, have altered greatly the functions of the different units of a copper smelter. Gangue minerals are removed from the feed so much more thoroughly that the reverberatory furnace, once virtually a concentrator in which a low-grade ore was concentrated into a rich matte by virtue of the removal of gangue elements as slag, has become very largely a melting furnace in which the rich flotation concentrates are rendered molten so that they may be converted. Moreover, since the proportion of matte to slag in the reverberatory furnace output is greater than it was formerly, the amount of converter slag returned to the reverberatory for cleaning is, in comparison to the amount of slag actually formed in that furnace, also much larger. In some cases, approximately half of the reverberatory dump slag may have originated in the converter. The increase in the proportion of convertor slag to total slag produced has brought about certain consequences not entirely desirable. Converter slags contain a high percentage of iron and therefore are high in specific gravity and are very basic. A considerable guantity of magnetite, both dissolved and suspended as solid crystals, is always a component, The basic nature of the ordinary converter slag and the presence of the suspended magnetite crystals make impossible the reduction of the copper content of the slag below approximately 1 per cent by even the most prelonged settling, and a re-treating process is necessary. At present, general practice in western copper smelters is to return the converter slag molten to the reverberatory furnace. Here dilution by mixing, with slag formed in the reverberatory furnace and reaction with raw sulphides and siliceous materials in the reverberatory feed reduce the magnetite and increase the silicates to the point necessary for a satisfactory dump slag.

Jan 1, 1930

By L. B. Pankratz

Present-day interest in the rare-earth elements and their compounds, for both metallurgical and ceramic uses, makes it highly desirable to accumulate basic thermodynamic data that can be applied to theoretical considerations of the processing of these substances. Such data still are seriously lacking. This Bureau of Mines paper reports the results of high-temperature heat content measurements of the sesquioxides of four rare-earth elements--europium, gadolinium, neodymium, and samarium--and of the closely related element, yttrium. The temperature ranges covered by the measurements are as follows: Monoclinic Eu2O3, 298°-1,802° K. Cubic Eu203, 298°-1,350° K. Monoclinic Gd203, 298-1,802° K. Cubic Gd203, 298°-1,550° K. Hexagonal Nd203, 298°-1,795° K. Monoclinic Sm203 298°-1,798° K. Cubic Sm203, 298°-1,149° K. Cubic Y203, 298°-1,799° K.

Jan 1, 1962